* [PATCH 1/2] shadow-sysroot: new recipe for useradd.bbclass support
2011-06-21 0:29 [PATCH 0/2] login.defs move Scott Garman
@ 2011-06-21 0:29 ` Scott Garman
2011-06-21 6:30 ` Koen Kooi
2011-06-21 0:29 ` [PATCH 2/2] base-passwd: remove login.defs references Scott Garman
2011-06-30 3:57 ` [PATCH 0/2] login.defs move Saul Wold
2 siblings, 1 reply; 6+ messages in thread
From: Scott Garman @ 2011-06-21 0:29 UTC (permalink / raw)
To: openembedded-core; +Cc: Scott Garman
Packaging login.defs with base-passwd causes problems due to the
file being included in target package installs. Instead, this
shadow-sysroot recipe can be used by useradd.bbclass to put
login.defs into the target sysroot without disturbing packages
intended for target devices.
Signed-off-by: Scott Garman <scott.a.garman@intel.com>
---
.../shadow/files/login.defs_shadow-sysroot | 386 ++++++++++++++++++++
.../shadow/shadow-sysroot_4.1.4.3.bb | 41 ++
2 files changed, 427 insertions(+), 0 deletions(-)
create mode 100644 meta/recipes-extended/shadow/files/login.defs_shadow-sysroot
create mode 100644 meta/recipes-extended/shadow/shadow-sysroot_4.1.4.3.bb
diff --git a/meta/recipes-extended/shadow/files/login.defs_shadow-sysroot b/meta/recipes-extended/shadow/files/login.defs_shadow-sysroot
new file mode 100644
index 0000000..8a68dd3
--- /dev/null
+++ b/meta/recipes-extended/shadow/files/login.defs_shadow-sysroot
@@ -0,0 +1,386 @@
+#
+# /etc/login.defs - Configuration control definitions for the shadow package.
+#
+# $Id: login.defs 3038 2009-07-23 20:41:35Z nekral-guest $
+#
+
+#
+# Delay in seconds before being allowed another attempt after a login failure
+# Note: When PAM is used, some modules may enfore a minimal delay (e.g.
+# pam_unix enforces a 2s delay)
+#
+FAIL_DELAY 3
+
+#
+# Enable logging and display of /var/log/faillog login failure info.
+#
+#FAILLOG_ENAB yes
+
+#
+# Enable display of unknown usernames when login failures are recorded.
+#
+LOG_UNKFAIL_ENAB no
+
+#
+# Enable logging of successful logins
+#
+LOG_OK_LOGINS no
+
+#
+# Enable logging and display of /var/log/lastlog login time info.
+#
+#LASTLOG_ENAB yes
+
+#
+# Enable checking and display of mailbox status upon login.
+#
+# Disable if the shell startup files already check for mail
+# ("mailx -e" or equivalent).
+#
+##MAIL_CHECK_ENAB yes
+
+#
+# Enable additional checks upon password changes.
+#
+#OBSCURE_CHECKS_ENAB yes
+
+#
+# Enable checking of time restrictions specified in /etc/porttime.
+#
+#PORTTIME_CHECKS_ENAB yes
+
+#
+# Enable setting of ulimit, umask, and niceness from passwd gecos field.
+#
+#QUOTAS_ENAB yes
+
+#
+# Enable "syslog" logging of su activity - in addition to sulog file logging.
+# SYSLOG_SG_ENAB does the same for newgrp and sg.
+#
+SYSLOG_SU_ENAB yes
+SYSLOG_SG_ENAB yes
+
+#
+# If defined, either full pathname of a file containing device names or
+# a ":" delimited list of device names. Root logins will be allowed only
+# upon these devices.
+#
+CONSOLE /etc/securetty
+#CONSOLE console:tty01:tty02:tty03:tty04
+
+#
+# If defined, all su activity is logged to this file.
+#
+#SULOG_FILE /var/log/sulog
+
+#
+# If defined, ":" delimited list of "message of the day" files to
+# be displayed upon login.
+#
+#MOTD_FILE /etc/motd
+#MOTD_FILE /etc/motd:/usr/lib/news/news-motd
+
+#
+# If defined, this file will be output before each login prompt.
+#
+#ISSUE_FILE /etc/issue
+
+#
+# If defined, file which maps tty line to TERM environment parameter.
+# Each line of the file is in a format something like "vt100 tty01".
+#
+#TTYTYPE_FILE /etc/ttytype
+
+#
+# If defined, login failures will be logged here in a utmp format.
+# last, when invoked as lastb, will read /var/log/btmp, so...
+#
+#FTMP_FILE /var/log/btmp
+
+#
+# If defined, name of file whose presence which will inhibit non-root
+# logins. The contents of this file should be a message indicating
+# why logins are inhibited.
+#
+#NOLOGINS_FILE /etc/nologin
+
+#
+# If defined, the command name to display when running "su -". For
+# example, if this is defined as "su" then a "ps" will display the
+# command is "-su". If not defined, then "ps" would display the
+# name of the shell actually being run, e.g. something like "-sh".
+#
+SU_NAME su
+
+#
+# *REQUIRED*
+# Directory where mailboxes reside, _or_ name of file, relative to the
+# home directory. If you _do_ define both, #MAIL_DIR takes precedence.
+#
+#MAIL_DIR /var/spool/mail
+MAIL_FILE .mail
+
+#
+# If defined, file which inhibits all the usual chatter during the login
+# sequence. If a full pathname, then hushed mode will be enabled if the
+# user's name or shell are found in the file. If not a full pathname, then
+# hushed mode will be enabled if the file exists in the user's home directory.
+#
+HUSHLOGIN_FILE .hushlogin
+#HUSHLOGIN_FILE /etc/hushlogins
+
+#
+# If defined, either a TZ environment parameter spec or the
+# fully-rooted pathname of a file containing such a spec.
+#
+#ENV_TZ TZ=CST6CDT
+#ENV_TZ /etc/tzname
+
+#
+# If defined, an HZ environment parameter spec.
+#
+# for Linux/x86
+#ENV_HZ HZ=100
+# For Linux/Alpha...
+#ENV_HZ HZ=1024
+
+#
+# *REQUIRED* The default PATH settings, for superuser and normal users.
+#
+# (they are minimal, add the rest in the shell startup files)
+ENV_SUPATH PATH=/sbin:/bin:/usr/sbin:/usr/bin
+ENV_PATH PATH=/bin:/usr/bin
+
+#
+# Terminal permissions
+#
+# TTYGROUP Login tty will be assigned this group ownership.
+# TTYPERM Login tty will be set to this permission.
+#
+# If you have a "write" program which is "setgid" to a special group
+# which owns the terminals, define TTYGROUP to the group number and
+# TTYPERM to 0620. Otherwise leave TTYGROUP commented out and assign
+# TTYPERM to either 622 or 600.
+#
+TTYGROUP tty
+TTYPERM 0600
+
+#
+# Login configuration initializations:
+#
+# ERASECHAR Terminal ERASE character ('\010' = backspace).
+# KILLCHAR Terminal KILL character ('\025' = CTRL/U).
+# ULIMIT Default "ulimit" value.
+#
+# The ERASECHAR and KILLCHAR are used only on System V machines.
+# The ULIMIT is used only if the system supports it.
+# (now it works with setrlimit too; ulimit is in 512-byte units)
+#
+# Prefix these values with "0" to get octal, "0x" to get hexadecimal.
+#
+ERASECHAR 0177
+KILLCHAR 025
+#ULIMIT 2097152
+
+# Default initial "umask" value for non-PAM enabled systems.
+# UMASK is also used by useradd and newusers to set the mode of new home
+# directories.
+# 022 is the default value, but 027, or even 077, could be considered
+# better for privacy. There is no One True Answer here: each sysadmin
+# must make up her mind.
+UMASK 022
+
+#
+# Password aging controls:
+#
+# PASS_MAX_DAYS Maximum number of days a password may be used.
+# PASS_MIN_DAYS Minimum number of days allowed between password changes.
+# PASS_MIN_LEN Minimum acceptable password length.
+# PASS_WARN_AGE Number of days warning given before a password expires.
+#
+PASS_MAX_DAYS 99999
+PASS_MIN_DAYS 0
+#PASS_MIN_LEN 5
+PASS_WARN_AGE 7
+
+#
+# If "yes", the user must be listed as a member of the first gid 0 group
+# in /etc/group (called "root" on most Linux systems) to be able to "su"
+# to uid 0 accounts. If the group doesn't exist or is empty, no one
+# will be able to "su" to uid 0.
+#
+#SU_WHEEL_ONLY no
+
+#
+# If compiled with cracklib support, where are the dictionaries
+#
+#CRACKLIB_DICTPATH /var/cache/cracklib/cracklib_dict
+
+#
+# Min/max values for automatic uid selection in useradd
+#
+UID_MIN 1000
+UID_MAX 60000
+# System accounts
+SYS_UID_MIN 101
+SYS_UID_MAX 999
+
+#
+# Min/max values for automatic gid selection in groupadd
+#
+GID_MIN 1000
+GID_MAX 60000
+# System accounts
+SYS_GID_MIN 101
+SYS_GID_MAX 999
+
+#
+# Max number of login retries if password is bad
+#
+LOGIN_RETRIES 5
+
+#
+# Max time in seconds for login
+#
+LOGIN_TIMEOUT 60
+
+#
+# Maximum number of attempts to change password if rejected (too easy)
+#
+#PASS_CHANGE_TRIES 5
+
+#
+# Warn about weak passwords (but still allow them) if you are root.
+#
+#PASS_ALWAYS_WARN yes
+
+#
+# Number of significant characters in the password for crypt().
+# Default is 8, don't change unless your crypt() is better.
+# Ignored if MD5_CRYPT_ENAB set to "yes".
+#
+#PASS_MAX_LEN 8
+
+#
+# Require password before chfn/chsh can make any changes.
+#
+#CHFN_AUTH yes
+
+#
+# Which fields may be changed by regular users using chfn - use
+# any combination of letters "frwh" (full name, room number, work
+# phone, home phone). If not defined, no changes are allowed.
+# For backward compatibility, "yes" = "rwh" and "no" = "frwh".
+#
+CHFN_RESTRICT rwh
+
+#
+# Password prompt (%s will be replaced by user name).
+#
+# XXX - it doesn't work correctly yet, for now leave it commented out
+# to use the default which is just "Password: ".
+#LOGIN_STRING "%s's Password: "
+
+#
+# Only works if compiled with MD5_CRYPT defined:
+# If set to "yes", new passwords will be encrypted using the MD5-based
+# algorithm compatible with the one used by recent releases of FreeBSD.
+# It supports passwords of unlimited length and longer salt strings.
+# Set to "no" if you need to copy encrypted passwords to other systems
+# which don't understand the new algorithm. Default is "no".
+#
+# Note: If you use PAM, it is recommended to use a value consistent with
+# the PAM modules configuration.
+#
+# This variable is deprecated. You should use ENCRYPT_METHOD.
+#
+#MD5_CRYPT_ENAB no
+
+#
+# Only works if compiled with ENCRYPTMETHOD_SELECT defined:
+# If set to MD5 , MD5-based algorithm will be used for encrypting password
+# If set to SHA256, SHA256-based algorithm will be used for encrypting password
+# If set to SHA512, SHA512-based algorithm will be used for encrypting password
+# If set to DES, DES-based algorithm will be used for encrypting password (default)
+# Overrides the MD5_CRYPT_ENAB option
+#
+# Note: If you use PAM, it is recommended to use a value consistent with
+# the PAM modules configuration.
+#
+#ENCRYPT_METHOD DES
+
+#
+# Only works if ENCRYPT_METHOD is set to SHA256 or SHA512.
+#
+# Define the number of SHA rounds.
+# With a lot of rounds, it is more difficult to brute forcing the password.
+# But note also that it more CPU resources will be needed to authenticate
+# users.
+#
+# If not specified, the libc will choose the default number of rounds (5000).
+# The values must be inside the 1000-999999999 range.
+# If only one of the MIN or MAX values is set, then this value will be used.
+# If MIN > MAX, the highest value will be used.
+#
+# SHA_CRYPT_MIN_ROUNDS 5000
+# SHA_CRYPT_MAX_ROUNDS 5000
+
+#
+# List of groups to add to the user's supplementary group set
+# when logging in on the console (as determined by the CONSOLE
+# setting). Default is none.
+#
+# Use with caution - it is possible for users to gain permanent
+# access to these groups, even when not logged in on the console.
+# How to do it is left as an exercise for the reader...
+#
+#CONSOLE_GROUPS floppy:audio:cdrom
+
+#
+# Should login be allowed if we can't cd to the home directory?
+# Default in no.
+#
+DEFAULT_HOME yes
+
+#
+# If this file exists and is readable, login environment will be
+# read from it. Every line should be in the form name=value.
+#
+#ENVIRON_FILE /etc/environment
+
+#
+# If defined, this command is run when removing a user.
+# It should remove any at/cron/print jobs etc. owned by
+# the user to be removed (passed as the first argument).
+#
+#USERDEL_CMD /usr/sbin/userdel_local
+
+#
+# Enable setting of the umask group bits to be the same as owner bits
+# (examples: 022 -> 002, 077 -> 007) for non-root users, if the uid is
+# the same as gid, and username is the same as the primary group name.
+#
+# This also enables userdel to remove user groups if no members exist.
+#
+USERGROUPS_ENAB yes
+
+#
+# If set to a non-nul number, the shadow utilities will make sure that
+# groups never have more than this number of users on one line.
+# This permit to support split groups (groups split into multiple lines,
+# with the same group ID, to avoid limitation of the line length in the
+# group file).
+#
+# 0 is the default value and disables this feature.
+#
+#MAX_MEMBERS_PER_GROUP 0
+
+#
+# If useradd should create home directories for users by default (non
+# system users only)
+# This option is overridden with the -M or -m flags on the useradd command
+# line.
+#
+CREATE_HOME yes
+
diff --git a/meta/recipes-extended/shadow/shadow-sysroot_4.1.4.3.bb b/meta/recipes-extended/shadow/shadow-sysroot_4.1.4.3.bb
new file mode 100644
index 0000000..3fd5da9
--- /dev/null
+++ b/meta/recipes-extended/shadow/shadow-sysroot_4.1.4.3.bb
@@ -0,0 +1,41 @@
+SUMMARY = "Shadow utils requirements for useradd.bbclass"
+DESCRIPTION = "Shadow utils requirements for useradd.bbclass"
+HOMEPAGE = "http://pkg-shadow.alioth.debian.org"
+BUGTRACKER = "https://alioth.debian.org/tracker/?group_id=30580"
+SECTION = "base utils"
+PRIORITY = "optional"
+LICENSE = "BSD | Artistic"
+LIC_FILES_CHKSUM = "file://login.defs_shadow-sysroot;md5=25e2f2de4dfc8f966ac5cdfce45cd7d5"
+
+DEPENDS = "base-passwd"
+
+PR = "r0"
+
+# The sole purpose of this recipe is to provide the /etc/login.defs
+# file for the target sysroot - needed so the shadow-native utilities
+# can add custom users/groups for recipes that use inherit useradd.
+SRC_URI = "file://login.defs_shadow-sysroot"
+
+SRC_URI[md5sum] = "b8608d8294ac88974f27b20f991c0e79"
+SRC_URI[sha256sum] = "633f5bb4ea0c88c55f3642c97f9d25cbef74f82e0b4cf8d54e7ad6f9f9caa778"
+
+S = "${WORKDIR}"
+SSTATEPOSTINSTFUNCS += "shadow_sysroot_sstate_postinst"
+
+do_install() {
+ install -d ${D}${sysconfdir}
+ install -p -m 755 ${S}/login.defs_shadow-sysroot ${D}${sysconfdir}/login.defs
+}
+
+shadow_sysroot_sstate_postinst() {
+ if [ "${BB_CURRENTTASK}" = "populate_sysroot" -o "${BB_CURRENTTASK}" = "populate_sysroot_setscene" ]
+ then
+ # Staging does not copy ${sysconfdir} files into the
+ # target sysroot, so we need to do so manually. We
+ # put this file in the target sysroot so it can be
+ # used by recipes which use custom user/group
+ # permissions.
+ install -d -m 755 ${STAGING_DIR_TARGET}${sysconfdir}
+ install -p -m 644 ${D}${sysconfdir}/login.defs ${STAGING_DIR_TARGET}/${sysconfdir}/login.defs
+ fi
+}
--
1.7.1
^ permalink raw reply related [flat|nested] 6+ messages in thread* Re: [PATCH 1/2] shadow-sysroot: new recipe for useradd.bbclass support
2011-06-21 0:29 ` [PATCH 1/2] shadow-sysroot: new recipe for useradd.bbclass support Scott Garman
@ 2011-06-21 6:30 ` Koen Kooi
2011-06-21 22:38 ` Scott Garman
0 siblings, 1 reply; 6+ messages in thread
From: Koen Kooi @ 2011-06-21 6:30 UTC (permalink / raw)
To: Patches and discussions about the oe-core layer; +Cc: Scott Garman
Op 21 jun 2011, om 02:29 heeft Scott Garman het volgende geschreven:
> Packaging login.defs with base-passwd causes problems due to the
> file being included in target package installs. Instead, this
> shadow-sysroot recipe can be used by useradd.bbclass to put
> login.defs into the target sysroot without disturbing packages
> intended for target devices.
So how does it end up on the target device after this?
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH 1/2] shadow-sysroot: new recipe for useradd.bbclass support
2011-06-21 6:30 ` Koen Kooi
@ 2011-06-21 22:38 ` Scott Garman
0 siblings, 0 replies; 6+ messages in thread
From: Scott Garman @ 2011-06-21 22:38 UTC (permalink / raw)
To: Koen Kooi; +Cc: Patches and discussions about the oe-core layer
On 06/20/2011 11:30 PM, Koen Kooi wrote:
>
> Op 21 jun 2011, om 02:29 heeft Scott Garman het volgende geschreven:
>
>> Packaging login.defs with base-passwd causes problems due to the
>> file being included in target package installs. Instead, this
>> shadow-sysroot recipe can be used by useradd.bbclass to put
>> login.defs into the target sysroot without disturbing packages
>> intended for target devices.
>
> So how does it end up on the target device after this?
login.defs would still end up on the target device when you install the
shadow (target) package. Otherwise the file is not needed (and hence,
should not have been packaged with base-passwd to begin with - my bad).
Scott
--
Scott Garman
Embedded Linux Engineer - Yocto Project
Intel Open Source Technology Center
^ permalink raw reply [flat|nested] 6+ messages in thread
* [PATCH 2/2] base-passwd: remove login.defs references
2011-06-21 0:29 [PATCH 0/2] login.defs move Scott Garman
2011-06-21 0:29 ` [PATCH 1/2] shadow-sysroot: new recipe for useradd.bbclass support Scott Garman
@ 2011-06-21 0:29 ` Scott Garman
2011-06-30 3:57 ` [PATCH 0/2] login.defs move Saul Wold
2 siblings, 0 replies; 6+ messages in thread
From: Scott Garman @ 2011-06-21 0:29 UTC (permalink / raw)
To: openembedded-core; +Cc: Scott Garman
login.defs is owned by shadow-utils, and doesn't belong here. The
shadow-sysroot recipe was created to handle the case this was
originally added for (useradd.bbclass support).
Signed-off-by: Scott Garman <scott.a.garman@intel.com>
---
.../base-passwd/base-passwd-3.5.22/login.defs | 386 --------------------
.../recipes-core/base-passwd/base-passwd_3.5.22.bb | 11 +-
2 files changed, 2 insertions(+), 395 deletions(-)
delete mode 100644 meta/recipes-core/base-passwd/base-passwd-3.5.22/login.defs
diff --git a/meta/recipes-core/base-passwd/base-passwd-3.5.22/login.defs b/meta/recipes-core/base-passwd/base-passwd-3.5.22/login.defs
deleted file mode 100644
index 1d392ac..0000000
--- a/meta/recipes-core/base-passwd/base-passwd-3.5.22/login.defs
+++ /dev/null
@@ -1,386 +0,0 @@
-#
-# /etc/login.defs - Configuration control definitions for the shadow package.
-#
-# $Id: login.defs 3038 2009-07-23 20:41:35Z nekral-guest $
-#
-
-#
-# Delay in seconds before being allowed another attempt after a login failure
-# Note: When PAM is used, some modules may enfore a minimal delay (e.g.
-# pam_unix enforces a 2s delay)
-#
-FAIL_DELAY 3
-
-#
-# Enable logging and display of /var/log/faillog login failure info.
-#
-FAILLOG_ENAB yes
-
-#
-# Enable display of unknown usernames when login failures are recorded.
-#
-LOG_UNKFAIL_ENAB no
-
-#
-# Enable logging of successful logins
-#
-LOG_OK_LOGINS no
-
-#
-# Enable logging and display of /var/log/lastlog login time info.
-#
-LASTLOG_ENAB yes
-
-#
-# Enable checking and display of mailbox status upon login.
-#
-# Disable if the shell startup files already check for mail
-# ("mailx -e" or equivalent).
-#
-#MAIL_CHECK_ENAB yes
-
-#
-# Enable additional checks upon password changes.
-#
-OBSCURE_CHECKS_ENAB yes
-
-#
-# Enable checking of time restrictions specified in /etc/porttime.
-#
-PORTTIME_CHECKS_ENAB yes
-
-#
-# Enable setting of ulimit, umask, and niceness from passwd gecos field.
-#
-QUOTAS_ENAB yes
-
-#
-# Enable "syslog" logging of su activity - in addition to sulog file logging.
-# SYSLOG_SG_ENAB does the same for newgrp and sg.
-#
-SYSLOG_SU_ENAB yes
-SYSLOG_SG_ENAB yes
-
-#
-# If defined, either full pathname of a file containing device names or
-# a ":" delimited list of device names. Root logins will be allowed only
-# upon these devices.
-#
-CONSOLE /etc/securetty
-#CONSOLE console:tty01:tty02:tty03:tty04
-
-#
-# If defined, all su activity is logged to this file.
-#
-#SULOG_FILE /var/log/sulog
-
-#
-# If defined, ":" delimited list of "message of the day" files to
-# be displayed upon login.
-#
-MOTD_FILE /etc/motd
-#MOTD_FILE /etc/motd:/usr/lib/news/news-motd
-
-#
-# If defined, this file will be output before each login prompt.
-#
-#ISSUE_FILE /etc/issue
-
-#
-# If defined, file which maps tty line to TERM environment parameter.
-# Each line of the file is in a format something like "vt100 tty01".
-#
-#TTYTYPE_FILE /etc/ttytype
-
-#
-# If defined, login failures will be logged here in a utmp format.
-# last, when invoked as lastb, will read /var/log/btmp, so...
-#
-FTMP_FILE /var/log/btmp
-
-#
-# If defined, name of file whose presence which will inhibit non-root
-# logins. The contents of this file should be a message indicating
-# why logins are inhibited.
-#
-NOLOGINS_FILE /etc/nologin
-
-#
-# If defined, the command name to display when running "su -". For
-# example, if this is defined as "su" then a "ps" will display the
-# command is "-su". If not defined, then "ps" would display the
-# name of the shell actually being run, e.g. something like "-sh".
-#
-SU_NAME su
-
-#
-# *REQUIRED*
-# Directory where mailboxes reside, _or_ name of file, relative to the
-# home directory. If you _do_ define both, #MAIL_DIR takes precedence.
-#
-#MAIL_DIR /var/spool/mail
-MAIL_FILE .mail
-
-#
-# If defined, file which inhibits all the usual chatter during the login
-# sequence. If a full pathname, then hushed mode will be enabled if the
-# user's name or shell are found in the file. If not a full pathname, then
-# hushed mode will be enabled if the file exists in the user's home directory.
-#
-HUSHLOGIN_FILE .hushlogin
-#HUSHLOGIN_FILE /etc/hushlogins
-
-#
-# If defined, either a TZ environment parameter spec or the
-# fully-rooted pathname of a file containing such a spec.
-#
-#ENV_TZ TZ=CST6CDT
-#ENV_TZ /etc/tzname
-
-#
-# If defined, an HZ environment parameter spec.
-#
-# for Linux/x86
-ENV_HZ HZ=100
-# For Linux/Alpha...
-#ENV_HZ HZ=1024
-
-#
-# *REQUIRED* The default PATH settings, for superuser and normal users.
-#
-# (they are minimal, add the rest in the shell startup files)
-ENV_SUPATH PATH=/sbin:/bin:/usr/sbin:/usr/bin
-ENV_PATH PATH=/bin:/usr/bin
-
-#
-# Terminal permissions
-#
-# TTYGROUP Login tty will be assigned this group ownership.
-# TTYPERM Login tty will be set to this permission.
-#
-# If you have a "write" program which is "setgid" to a special group
-# which owns the terminals, define TTYGROUP to the group number and
-# TTYPERM to 0620. Otherwise leave TTYGROUP commented out and assign
-# TTYPERM to either 622 or 600.
-#
-TTYGROUP tty
-TTYPERM 0600
-
-#
-# Login configuration initializations:
-#
-# ERASECHAR Terminal ERASE character ('\010' = backspace).
-# KILLCHAR Terminal KILL character ('\025' = CTRL/U).
-# ULIMIT Default "ulimit" value.
-#
-# The ERASECHAR and KILLCHAR are used only on System V machines.
-# The ULIMIT is used only if the system supports it.
-# (now it works with setrlimit too; ulimit is in 512-byte units)
-#
-# Prefix these values with "0" to get octal, "0x" to get hexadecimal.
-#
-ERASECHAR 0177
-KILLCHAR 025
-#ULIMIT 2097152
-
-# Default initial "umask" value for non-PAM enabled systems.
-# UMASK is also used by useradd and newusers to set the mode of new home
-# directories.
-# 022 is the default value, but 027, or even 077, could be considered
-# better for privacy. There is no One True Answer here: each sysadmin
-# must make up her mind.
-UMASK 022
-
-#
-# Password aging controls:
-#
-# PASS_MAX_DAYS Maximum number of days a password may be used.
-# PASS_MIN_DAYS Minimum number of days allowed between password changes.
-# PASS_MIN_LEN Minimum acceptable password length.
-# PASS_WARN_AGE Number of days warning given before a password expires.
-#
-PASS_MAX_DAYS 99999
-PASS_MIN_DAYS 0
-PASS_MIN_LEN 5
-PASS_WARN_AGE 7
-
-#
-# If "yes", the user must be listed as a member of the first gid 0 group
-# in /etc/group (called "root" on most Linux systems) to be able to "su"
-# to uid 0 accounts. If the group doesn't exist or is empty, no one
-# will be able to "su" to uid 0.
-#
-SU_WHEEL_ONLY no
-
-#
-# If compiled with cracklib support, where are the dictionaries
-#
-CRACKLIB_DICTPATH /var/cache/cracklib/cracklib_dict
-
-#
-# Min/max values for automatic uid selection in useradd
-#
-UID_MIN 1000
-UID_MAX 60000
-# System accounts
-SYS_UID_MIN 101
-SYS_UID_MAX 999
-
-#
-# Min/max values for automatic gid selection in groupadd
-#
-GID_MIN 1000
-GID_MAX 60000
-# System accounts
-SYS_GID_MIN 101
-SYS_GID_MAX 999
-
-#
-# Max number of login retries if password is bad
-#
-LOGIN_RETRIES 5
-
-#
-# Max time in seconds for login
-#
-LOGIN_TIMEOUT 60
-
-#
-# Maximum number of attempts to change password if rejected (too easy)
-#
-PASS_CHANGE_TRIES 5
-
-#
-# Warn about weak passwords (but still allow them) if you are root.
-#
-PASS_ALWAYS_WARN yes
-
-#
-# Number of significant characters in the password for crypt().
-# Default is 8, don't change unless your crypt() is better.
-# Ignored if MD5_CRYPT_ENAB set to "yes".
-#
-#PASS_MAX_LEN 8
-
-#
-# Require password before chfn/chsh can make any changes.
-#
-CHFN_AUTH yes
-
-#
-# Which fields may be changed by regular users using chfn - use
-# any combination of letters "frwh" (full name, room number, work
-# phone, home phone). If not defined, no changes are allowed.
-# For backward compatibility, "yes" = "rwh" and "no" = "frwh".
-#
-CHFN_RESTRICT rwh
-
-#
-# Password prompt (%s will be replaced by user name).
-#
-# XXX - it doesn't work correctly yet, for now leave it commented out
-# to use the default which is just "Password: ".
-#LOGIN_STRING "%s's Password: "
-
-#
-# Only works if compiled with MD5_CRYPT defined:
-# If set to "yes", new passwords will be encrypted using the MD5-based
-# algorithm compatible with the one used by recent releases of FreeBSD.
-# It supports passwords of unlimited length and longer salt strings.
-# Set to "no" if you need to copy encrypted passwords to other systems
-# which don't understand the new algorithm. Default is "no".
-#
-# Note: If you use PAM, it is recommended to use a value consistent with
-# the PAM modules configuration.
-#
-# This variable is deprecated. You should use ENCRYPT_METHOD.
-#
-#MD5_CRYPT_ENAB no
-
-#
-# Only works if compiled with ENCRYPTMETHOD_SELECT defined:
-# If set to MD5 , MD5-based algorithm will be used for encrypting password
-# If set to SHA256, SHA256-based algorithm will be used for encrypting password
-# If set to SHA512, SHA512-based algorithm will be used for encrypting password
-# If set to DES, DES-based algorithm will be used for encrypting password (default)
-# Overrides the MD5_CRYPT_ENAB option
-#
-# Note: If you use PAM, it is recommended to use a value consistent with
-# the PAM modules configuration.
-#
-#ENCRYPT_METHOD DES
-
-#
-# Only works if ENCRYPT_METHOD is set to SHA256 or SHA512.
-#
-# Define the number of SHA rounds.
-# With a lot of rounds, it is more difficult to brute forcing the password.
-# But note also that it more CPU resources will be needed to authenticate
-# users.
-#
-# If not specified, the libc will choose the default number of rounds (5000).
-# The values must be inside the 1000-999999999 range.
-# If only one of the MIN or MAX values is set, then this value will be used.
-# If MIN > MAX, the highest value will be used.
-#
-# SHA_CRYPT_MIN_ROUNDS 5000
-# SHA_CRYPT_MAX_ROUNDS 5000
-
-#
-# List of groups to add to the user's supplementary group set
-# when logging in on the console (as determined by the CONSOLE
-# setting). Default is none.
-#
-# Use with caution - it is possible for users to gain permanent
-# access to these groups, even when not logged in on the console.
-# How to do it is left as an exercise for the reader...
-#
-#CONSOLE_GROUPS floppy:audio:cdrom
-
-#
-# Should login be allowed if we can't cd to the home directory?
-# Default in no.
-#
-DEFAULT_HOME yes
-
-#
-# If this file exists and is readable, login environment will be
-# read from it. Every line should be in the form name=value.
-#
-ENVIRON_FILE /etc/environment
-
-#
-# If defined, this command is run when removing a user.
-# It should remove any at/cron/print jobs etc. owned by
-# the user to be removed (passed as the first argument).
-#
-#USERDEL_CMD /usr/sbin/userdel_local
-
-#
-# Enable setting of the umask group bits to be the same as owner bits
-# (examples: 022 -> 002, 077 -> 007) for non-root users, if the uid is
-# the same as gid, and username is the same as the primary group name.
-#
-# This also enables userdel to remove user groups if no members exist.
-#
-USERGROUPS_ENAB yes
-
-#
-# If set to a non-nul number, the shadow utilities will make sure that
-# groups never have more than this number of users on one line.
-# This permit to support split groups (groups split into multiple lines,
-# with the same group ID, to avoid limitation of the line length in the
-# group file).
-#
-# 0 is the default value and disables this feature.
-#
-#MAX_MEMBERS_PER_GROUP 0
-
-#
-# If useradd should create home directories for users by default (non
-# system users only)
-# This option is overridden with the -M or -m flags on the useradd command
-# line.
-#
-CREATE_HOME yes
-
diff --git a/meta/recipes-core/base-passwd/base-passwd_3.5.22.bb b/meta/recipes-core/base-passwd/base-passwd_3.5.22.bb
index 3315c68..ffde423 100644
--- a/meta/recipes-core/base-passwd/base-passwd_3.5.22.bb
+++ b/meta/recipes-core/base-passwd/base-passwd_3.5.22.bb
@@ -1,14 +1,13 @@
SUMMARY = "Base system master password/group files."
DESCRIPTION = "The master copies of the user database files (/etc/passwd and /etc/group). The update-passwd tool is also provided to keep the system databases synchronized with these master files."
SECTION = "base"
-PR = "r2"
+PR = "r3"
LICENSE = "GPLv2+"
LIC_FILES_CHKSUM = "file://COPYING;md5=eb723b61539feef013de476e68b5c50a"
SRC_URI = "${DEBIAN_MIRROR}/main/b/base-passwd/base-passwd_${PV}.tar.gz \
file://nobash.patch \
- file://root-home.patch \
- file://login.defs"
+ file://root-home.patch"
SRC_URI[md5sum] = "47f22ab6b572d0133409ff6ad1fab402"
SRC_URI[sha256sum] = "d34acb35a9f9f221e7e4f642b9ef4b22083dd77bb2fc7216756f445316d842fc"
@@ -30,7 +29,6 @@ do_install () {
install -d -m 755 ${D}${datadir}/base-passwd
install -p -m 644 passwd.master ${D}${datadir}/base-passwd/
install -p -m 644 group.master ${D}${datadir}/base-passwd/
- install -p -m 644 ${S}/../login.defs ${D}${datadir}/base-passwd/login.defs
install -d -m 755 ${D}${docdir}/${PN}
install -p -m 644 debian/changelog ${D}${docdir}/${PN}/
@@ -49,10 +47,6 @@ pkg_postinst_${PN} () {
if [ ! -e $D${sysconfdir}/group ] ; then
cp $D${datadir}/base-passwd/group.master $D${sysconfdir}/group
fi
-
- if [ ! -e $D{sysconfdir}/login.defs ] ; then
- cp $D${datadir}/base-passwd/login.defs $D${sysconfdir}/login.defs
- fi
exit 0
}
@@ -67,6 +61,5 @@ base_passwd_sstate_postinst() {
install -d -m 755 ${STAGING_DIR_TARGET}${sysconfdir}
install -p -m 644 ${STAGING_DIR_TARGET}${datadir}/base-passwd/passwd.master ${STAGING_DIR_TARGET}${sysconfdir}/passwd
install -p -m 644 ${STAGING_DIR_TARGET}${datadir}/base-passwd/group.master ${STAGING_DIR_TARGET}${sysconfdir}/group
- install -p -m 644 ${STAGING_DIR_TARGET}${datadir}/base-passwd/login.defs ${STAGING_DIR_TARGET}/${sysconfdir}/login.defs
fi
}
--
1.7.1
^ permalink raw reply related [flat|nested] 6+ messages in thread* Re: [PATCH 0/2] login.defs move
2011-06-21 0:29 [PATCH 0/2] login.defs move Scott Garman
2011-06-21 0:29 ` [PATCH 1/2] shadow-sysroot: new recipe for useradd.bbclass support Scott Garman
2011-06-21 0:29 ` [PATCH 2/2] base-passwd: remove login.defs references Scott Garman
@ 2011-06-30 3:57 ` Saul Wold
2 siblings, 0 replies; 6+ messages in thread
From: Saul Wold @ 2011-06-30 3:57 UTC (permalink / raw)
To: Patches and discussions about the oe-core layer; +Cc: Scott Garman
On 06/20/2011 05:29 PM, Scott Garman wrote:
> Hello,
>
> This pull request moves the login.defs file previously included
> with base-passwd into a more appropriate recipe, shadow-sysroot
> (I'm not married to that recipe name if someone can suggest
> something better).
>
> login.defs is part of shadow-utils and the copy included with
> base-passwd was contaminating target package installations.
> Moving it into its own recipe keeps it logically separate and
> easier to manage the requirements of useradd.bbclass.
>
> The following changes since commit 2163461ec94528ecf046a04edc5db3d2dd3a6b8b:
>
> systemtap: remove non-core COMPATIBLE_MACHINES (2011-06-16 22:14:06 +0100)
>
> are available in the git repository at:
> git://git.pokylinux.org/poky-contrib sgarman/login-defs-move
> http://git.pokylinux.org/cgit.cgi/poky-contrib/log/?h=sgarman/login-defs-move
>
> Scott Garman (2):
> shadow-sysroot: new recipe for useradd.bbclass support
> base-passwd: remove login.defs references
>
> .../recipes-core/base-passwd/base-passwd_3.5.22.bb | 11 +----
> .../shadow/files/login.defs_shadow-sysroot} | 34 ++++++++--------
> .../shadow/shadow-sysroot_4.1.4.3.bb | 41 ++++++++++++++++++++
> 3 files changed, 60 insertions(+), 26 deletions(-)
> rename meta/{recipes-core/base-passwd/base-passwd-3.5.22/login.defs => recipes-extended/shadow/files/login.defs_shadow-sysroot} (96%)
> create mode 100644 meta/recipes-extended/shadow/shadow-sysroot_4.1.4.3.bb
>
>
> _______________________________________________
> Openembedded-core mailing list
> Openembedded-core@lists.openembedded.org
> http://lists.linuxtogo.org/cgi-bin/mailman/listinfo/openembedded-core
>
Merged into OE-Core
Thanks
Sau!
^ permalink raw reply [flat|nested] 6+ messages in thread