From: Richard Purdie <richard.purdie@linuxfoundation.org>
To: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
Cc: Poky <poky@lists.pokylinux.org>
Subject: Re: Booting BeagleBoard
Date: Mon, 14 Feb 2011 12:35:22 +0000 [thread overview]
Message-ID: <1297686922.4945.23.camel@rex> (raw)
In-Reply-To: <AANLkTikp04oEA4EL8tKC2VbDthfBHUgXPhkUMOqX=Zgn@mail.gmail.com>
On Sun, 2011-02-13 at 19:14 +0100, Frans Meulenbroeks wrote:
> 2011/2/13 Gary Thomas <gary@mlbassoc.com>:
> > On 02/13/2011 08:21 AM, Koen Kooi wrote:
> >>
> >> Op 13 feb 2011, om 16:06 heeft Gary Thomas het volgende geschreven:
> >>
> >>> On 02/13/2011 08:00 AM, Koen Kooi wrote:
> >>>>
> >>>> Op 13 feb 2011, om 15:57 heeft Gary Thomas het volgende geschreven:
> >>>>
> >>>>> On 02/12/2011 08:01 AM, Koen Kooi wrote:
> >>>>>>
> >>>>>> Op 12 feb 2011, om 15:52 heeft Gary Thomas het volgende geschreven:
> >>>>>>
> >>>>>>> I have a BeagleBoard C3 (not the new xM). Trying to run the
> >>>>>>> latest Poky ran into some problems:
> >>>>>>>
> >>>>>>> * The boot commands in README.hardware are no longer accurate
> >>>>>>> for the 2.6.37 (linux-yocto) kernel. At least you need to
> >>>>>>> use ttyO2 for the serial console.
> >>>>>>> * There is no video? /dev/fb0 is not being created.
> >>>>>>>
> >>>>>>> I know that the previous (Angstrom based) 2.6.32 kernel had
> >>>>>>> lots of additions which support video (DSS subsystem) and
> >>>>>>> also camera (ISP). Has this support been ported forward
> >>>>>>> into the Yocto kernel?
> >>>>>>
> >>>>>> Even better, there is a proper BSP with beagleboard support:
> >>>>>> http://gitorious.org/angstrom/angstrom-layers/commits/master
> >>>>>
> >>>>> How is this used? I tried just adding a pointer to that tree
> >>>>> in my conf/bblayers.conf. I also tried moving that tree into
> >>>>> my poky sources at the same level as meta-emenlow, etc. Both
> >>>>> attempts immediately yielded this error:
> >>>>> ERROR: Unable to parse conf/bitbake.conf: Could not include required
> >>>>> file conf/machine/include/omap3.inc
> >>>>>
> >>>>> Perhaps you can give some guidance for how to use this?
> >>>>
> >>>>
> >>>> http://thread.gmane.org/gmane.linux.distributions.angstrom.devel/4698/focus=4700
> >>>
> >>> Obviously this is not what I'm looking for.
> >>>
> >>> What I had wanted to test was your layering on top of my extant
> >>> Poky/Yocto environment. I don't want to start over as I have my
> >>> own layers that work just fine with Poky.
> >>
> >> I obviously misunderstood your request on the angstrom mailinglist on how
> >> to setup angstrom on top of yocto as a request on how to setup angstrom on
> >> top of yocto. I'm sorry that I fail to understand such obvious things. I
> >> will from now on stop trying to understand your requests to avoid any
> >> confusion and perceived wrongdoing on my part.
> >
> > That would be reasonable except that this entire thread was on
> > the Poky mailing list :-) If you look closely, I asked about
> > running the BeagleBoard on the latest Poky/Yocto and you replied
> > with this info about your angstrom layers.
>
> Gary, you're better off ignoring Koen.
> Apparently he hasn't taken his medicine this morning.
> And, frankly speaking, the reply above is among hismore friendly ones.
> His mission in life seems to be to drive everyone away from OE (unless
> of course you're one of his fan-boys). Guess he tries to pull the same
> trick with poky/yocto.
> Sometimes I really pity Richard, having to deal with someone like Koen..
Until now we've managed to keep the Poky/Yocto lists clear of this kind
of discussion. I'd like to point out:
https://wiki.yoctoproject.org/wiki/Community_Guidelines
and
http://www.yoctoproject.org/tos
Specifically, its usually better to keep discussions to technical
grounds and not make them personal.
Cheers,
Richard
next prev parent reply other threads:[~2011-02-14 12:35 UTC|newest]
Thread overview: 14+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-02-12 14:52 Booting BeagleBoard Gary Thomas
2011-02-12 14:55 ` Gary Thomas
2011-02-14 16:34 ` Darren Hart
2011-02-12 15:01 ` Koen Kooi
2011-02-13 14:57 ` Gary Thomas
2011-02-13 15:00 ` Koen Kooi
2011-02-13 15:06 ` Gary Thomas
2011-02-13 15:21 ` Koen Kooi
2011-02-13 15:32 ` Gary Thomas
2011-02-13 18:14 ` Frans Meulenbroeks
2011-02-14 12:35 ` Richard Purdie [this message]
2011-02-14 13:23 ` Frans Meulenbroeks
2011-02-13 1:21 ` Bruce Ashfield
2011-02-14 16:32 ` Darren Hart
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1297686922.4945.23.camel@rex \
--to=richard.purdie@linuxfoundation.org \
--cc=fransmeulenbroeks@gmail.com \
--cc=poky@lists.pokylinux.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox