From: Jamin Lin <jamin_lin@aspeedtech.com>
To: "Cédric Le Goater" <clg@kaod.org>,
"Peter Maydell" <peter.maydell@linaro.org>,
"Steven Lee" <steven_lee@aspeedtech.com>,
"Troy Lee" <leetroy@gmail.com>,
"Kane Chen" <kane_chen@aspeedtech.com>,
"Andrew Jeffery" <andrew@codeconstruct.com.au>,
"Joel Stanley" <joel@jms.id.au>,
"open list:ASPEED BMCs" <qemu-arm@nongnu.org>,
"open list:All patches CC here" <qemu-devel@nongnu.org>
Cc: Jamin Lin <jamin_lin@aspeedtech.com>, Troy Lee <troy_lee@aspeedtech.com>
Subject: [PATCH v1 01/10] hw/i2c/aspeed_i2c: Introduce dma_addr_lo_mask to unify DMA address handling
Date: Fri, 29 May 2026 06:42:45 +0000 [thread overview]
Message-ID: <20260529064243.2064188-2-jamin_lin@aspeedtech.com> (raw)
In-Reply-To: <20260529064243.2064188-1-jamin_lin@aspeedtech.com>
The Aspeed I2C controller has two register layouts.
The AST2500 uses the old mode with a single DMA address register (I2CD_DMA_ADDR)
where the address is 4-byte aligned and masked to 0x3ffffffc.
From AST2600 onwards, the new mode provides separate master TX/RX and slave RX DMA
address registers (I2CM_DMA_TX_ADDR, I2CM_DMA_RX_ADDR, I2CS_DMA_RX_ADDR)
with different address widths per SoC:
AST2600 (new mode): 0x7fffffff - bits[30:0]
AST1030 (new mode): 0x7fffffff - bits[30:0]
AST1060 (new mode): 0x7fffffff - bits[30:0]
AST2700 (new mode): 0xffffffff - bits[31:0]
Introduce dma_addr_lo_mask as a per-class attribute and apply it
uniformly when storing DMA address register writes and when loading
the address into dma_dram_offset for both master and slave paths.
This replaces the previous FIELD_EX32 extractions (which incorrectly
stripped bit 31 on AST2700) and the hardcoded 0x3ffffffc literal in
the old-mode path.
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
---
include/hw/i2c/aspeed_i2c.h | 5 +----
hw/i2c/aspeed_i2c.c | 22 +++++++++++++---------
2 files changed, 14 insertions(+), 13 deletions(-)
diff --git a/include/hw/i2c/aspeed_i2c.h b/include/hw/i2c/aspeed_i2c.h
index d42cb4865a..1fc229f699 100644
--- a/include/hw/i2c/aspeed_i2c.h
+++ b/include/hw/i2c/aspeed_i2c.h
@@ -209,13 +209,9 @@ REG32(I2CS_DMA_LEN, 0x2c)
FIELD(I2CS_DMA_LEN, TX_BUF_LEN_W1T, 15, 1)
FIELD(I2CS_DMA_LEN, TX_BUF_LEN, 0, 11)
REG32(I2CM_DMA_TX_ADDR, 0x30)
- FIELD(I2CM_DMA_TX_ADDR, ADDR, 0, 31)
REG32(I2CM_DMA_RX_ADDR, 0x34)
- FIELD(I2CM_DMA_RX_ADDR, ADDR, 0, 31)
REG32(I2CS_DMA_TX_ADDR, 0x38)
- FIELD(I2CS_DMA_TX_ADDR, ADDR, 0, 31)
REG32(I2CS_DMA_RX_ADDR, 0x3c)
- FIELD(I2CS_DMA_RX_ADDR, ADDR, 0, 31)
REG32(I2CS_DEV_ADDR, 0x40)
REG32(I2CM_DMA_LEN_STS, 0x48)
FIELD(I2CM_DMA_LEN_STS, RX_LEN, 16, 13)
@@ -303,6 +299,7 @@ struct AspeedI2CClass {
bool has_share_pool;
uint64_t mem_size;
bool has_dma64;
+ uint32_t dma_addr_lo_mask;
};
static inline bool aspeed_i2c_is_new_mode(AspeedI2CState *s)
diff --git a/hw/i2c/aspeed_i2c.c b/hw/i2c/aspeed_i2c.c
index 80c4457500..9c0387a394 100644
--- a/hw/i2c/aspeed_i2c.c
+++ b/hw/i2c/aspeed_i2c.c
@@ -236,7 +236,7 @@ static void aspeed_i2c_set_tx_dma_dram_offset(AspeedI2CBus *bus)
value = bus->regs[R_I2CM_DMA_TX_ADDR];
bus->dma_dram_offset =
deposit64(bus->dma_dram_offset, 0, 32,
- FIELD_EX32(value, I2CM_DMA_TX_ADDR, ADDR));
+ value & aic->dma_addr_lo_mask);
if (aic->has_dma64) {
value = bus->regs[R_I2CM_DMA_TX_ADDR_HI];
bus->dma_dram_offset =
@@ -246,7 +246,7 @@ static void aspeed_i2c_set_tx_dma_dram_offset(AspeedI2CBus *bus)
} else {
value = bus->regs[R_I2CD_DMA_ADDR];
bus->dma_dram_offset = deposit64(bus->dma_dram_offset, 0, 32,
- value & 0x3ffffffc);
+ value & aic->dma_addr_lo_mask);
}
}
@@ -261,7 +261,7 @@ static void aspeed_i2c_set_rx_dma_dram_offset(AspeedI2CBus *bus)
value = bus->regs[R_I2CM_DMA_RX_ADDR];
bus->dma_dram_offset =
deposit64(bus->dma_dram_offset, 0, 32,
- FIELD_EX32(value, I2CM_DMA_RX_ADDR, ADDR));
+ value & aic->dma_addr_lo_mask);
if (aic->has_dma64) {
value = bus->regs[R_I2CM_DMA_RX_ADDR_HI];
bus->dma_dram_offset =
@@ -271,7 +271,7 @@ static void aspeed_i2c_set_rx_dma_dram_offset(AspeedI2CBus *bus)
} else {
value = bus->regs[R_I2CD_DMA_ADDR];
bus->dma_dram_offset = deposit64(bus->dma_dram_offset, 0, 32,
- value & 0x3ffffffc);
+ value & aic->dma_addr_lo_mask);
}
}
@@ -735,12 +735,10 @@ static void aspeed_i2c_bus_new_write(AspeedI2CBus *bus, hwaddr offset,
aspeed_i2c_bus_raise_interrupt(bus);
break;
case A_I2CM_DMA_TX_ADDR:
- bus->regs[R_I2CM_DMA_TX_ADDR] = FIELD_EX32(value, I2CM_DMA_TX_ADDR,
- ADDR);
+ bus->regs[R_I2CM_DMA_TX_ADDR] = value & aic->dma_addr_lo_mask;
break;
case A_I2CM_DMA_RX_ADDR:
- bus->regs[R_I2CM_DMA_RX_ADDR] = FIELD_EX32(value, I2CM_DMA_RX_ADDR,
- ADDR);
+ bus->regs[R_I2CM_DMA_RX_ADDR] = value & aic->dma_addr_lo_mask;
break;
case A_I2CM_DMA_LEN:
w1t = FIELD_EX32(value, I2CM_DMA_LEN, RX_BUF_LEN_W1T) ||
@@ -1385,6 +1383,8 @@ static const TypeInfo aspeed_i2c_info = {
static int aspeed_i2c_bus_new_slave_event(AspeedI2CBus *bus,
enum i2c_event event)
{
+ AspeedI2CClass *aic = ASPEED_I2C_GET_CLASS(bus->controller);
+
switch (event) {
case I2C_START_SEND_ASYNC:
if (!SHARED_ARRAY_FIELD_EX32(bus->regs, R_I2CS_CMD, RX_DMA_EN)) {
@@ -1395,7 +1395,7 @@ static int aspeed_i2c_bus_new_slave_event(AspeedI2CBus *bus,
ARRAY_FIELD_DP32(bus->regs, I2CS_DMA_LEN_STS, RX_LEN, 0);
bus->dma_dram_offset =
deposit64(bus->dma_dram_offset, 0, 32,
- ARRAY_FIELD_EX32(bus->regs, I2CS_DMA_RX_ADDR, ADDR));
+ bus->regs[R_I2CS_DMA_RX_ADDR] & aic->dma_addr_lo_mask);
bus->regs[R_I2CC_DMA_LEN] =
ARRAY_FIELD_EX32(bus->regs, I2CS_DMA_LEN, RX_BUF_LEN) + 1;
i2c_ack(bus->bus);
@@ -1638,6 +1638,7 @@ static void aspeed_2500_i2c_class_init(ObjectClass *klass, const void *data)
aic->check_sram = true;
aic->has_dma = true;
aic->mem_size = 0x1000;
+ aic->dma_addr_lo_mask = 0x3ffffffc;
}
static const TypeInfo aspeed_2500_i2c_info = {
@@ -1667,6 +1668,7 @@ static void aspeed_2600_i2c_class_init(ObjectClass *klass, const void *data)
aic->bus_pool_base = aspeed_2500_i2c_bus_pool_base;
aic->has_dma = true;
aic->mem_size = 0x1000;
+ aic->dma_addr_lo_mask = 0x7fffffff;
}
static const TypeInfo aspeed_2600_i2c_info = {
@@ -1691,6 +1693,7 @@ static void aspeed_1030_i2c_class_init(ObjectClass *klass, const void *data)
aic->bus_pool_base = aspeed_2500_i2c_bus_pool_base;
aic->has_dma = true;
aic->mem_size = 0x10000;
+ aic->dma_addr_lo_mask = 0x7fffffff;
}
static const TypeInfo aspeed_1030_i2c_info = {
@@ -1718,6 +1721,7 @@ static void aspeed_2700_i2c_class_init(ObjectClass *klass, const void *data)
aic->has_dma = true;
aic->mem_size = 0x2000;
aic->has_dma64 = true;
+ aic->dma_addr_lo_mask = 0xffffffff;
}
static const TypeInfo aspeed_2700_i2c_info = {
--
2.43.0
next prev parent reply other threads:[~2026-05-29 6:45 UTC|newest]
Thread overview: 26+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-05-29 6:42 [PATCH v1 00/10] hw/arm: Add AST1040 peripheral support Jamin Lin
2026-05-29 6:42 ` Jamin Lin [this message]
2026-06-01 12:51 ` [PATCH v1 01/10] hw/i2c/aspeed_i2c: Introduce dma_addr_lo_mask to unify DMA address handling Cédric Le Goater
2026-06-02 3:12 ` Jamin Lin
2026-05-29 6:42 ` [PATCH v1 02/10] hw/i2c/aspeed_i2c: Increase AST2700 buffer mode size and adjust offset Jamin Lin
2026-06-01 12:50 ` Cédric Le Goater
2026-06-02 2:54 ` Jamin Lin
2026-05-29 6:42 ` [PATCH v1 03/10] hw/arm/aspeed_ast1040: Reuse AST2700 ADC model Jamin Lin
2026-06-01 12:52 ` Cédric Le Goater
2026-05-29 6:42 ` [PATCH v1 04/10] hw/arm/aspeed_ast1040: Introduce PECI support Jamin Lin
2026-06-01 12:52 ` Cédric Le Goater
2026-05-29 6:42 ` [PATCH v1 05/10] hw/arm/aspeed_ast1040: Reuse AST2700 GPIO controller model Jamin Lin
2026-06-01 12:52 ` Cédric Le Goater
2026-05-29 6:42 ` [PATCH v1 06/10] hw/arm/aspeed_ast1040: Add SGPIO controller support Jamin Lin
2026-06-01 12:54 ` Cédric Le Goater
2026-05-29 6:42 ` [PATCH v1 07/10] hw/i2c/aspeed_i2c: Introduce AST1040 I2C model Jamin Lin
2026-06-01 12:57 ` Cédric Le Goater
2026-06-02 3:34 ` Jamin Lin
2026-05-29 6:42 ` [PATCH v1 08/10] hw/arm/aspeed_ast1040: Introduce I2C support Jamin Lin
2026-06-01 13:00 ` Cédric Le Goater
2026-06-02 3:45 ` Jamin Lin
2026-05-29 6:42 ` [PATCH v1 09/10] hw/arm/aspeed_ast1040_evb: Introduce onboard I2C device Jamin Lin
2026-06-01 13:02 ` Cédric Le Goater
2026-06-02 3:47 ` Jamin Lin
2026-05-29 6:42 ` [PATCH v1 10/10] hw/arm/aspeed_ast1040: Reuse AST2700 watchdog models Jamin Lin
2026-06-01 13:03 ` Cédric Le Goater
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20260529064243.2064188-2-jamin_lin@aspeedtech.com \
--to=jamin_lin@aspeedtech.com \
--cc=andrew@codeconstruct.com.au \
--cc=clg@kaod.org \
--cc=joel@jms.id.au \
--cc=kane_chen@aspeedtech.com \
--cc=leetroy@gmail.com \
--cc=peter.maydell@linaro.org \
--cc=qemu-arm@nongnu.org \
--cc=qemu-devel@nongnu.org \
--cc=steven_lee@aspeedtech.com \
--cc=troy_lee@aspeedtech.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox