From: Jamin Lin <jamin_lin@aspeedtech.com>
To: "Cédric Le Goater" <clg@kaod.org>,
"Peter Maydell" <peter.maydell@linaro.org>,
"Steven Lee" <steven_lee@aspeedtech.com>,
"Troy Lee" <leetroy@gmail.com>,
"Kane Chen" <kane_chen@aspeedtech.com>,
"Andrew Jeffery" <andrew@codeconstruct.com.au>,
"Joel Stanley" <joel@jms.id.au>,
"open list:ASPEED BMCs" <qemu-arm@nongnu.org>,
"open list:All patches CC here" <qemu-devel@nongnu.org>
Cc: Jamin Lin <jamin_lin@aspeedtech.com>, Troy Lee <troy_lee@aspeedtech.com>
Subject: [PATCH v1 07/10] hw/i2c/aspeed_i2c: Introduce AST1040 I2C model
Date: Fri, 29 May 2026 06:42:52 +0000 [thread overview]
Message-ID: <20260529064243.2064188-8-jamin_lin@aspeedtech.com> (raw)
In-Reply-To: <20260529064243.2064188-1-jamin_lin@aspeedtech.com>
Introduce the AST1040 I2C controller model.
The AST1040 I2C controller is compatible with the AST2700 I2C controller,
including DMA support and the 64-bit DMA address registers. Set has_dma64 so
firmware can access the high address register and program it to zero, as the
CM4 CPU only supports 32-bit addressing.
Since AST1040 has 16MB HyperRAM, limit the DMA low address mask to
0x00ffffff.
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
---
include/hw/i2c/aspeed_i2c.h | 1 +
hw/i2c/aspeed_i2c.c | 29 +++++++++++++++++++++++++++++
2 files changed, 30 insertions(+)
diff --git a/include/hw/i2c/aspeed_i2c.h b/include/hw/i2c/aspeed_i2c.h
index b2e4d2fb9d..156998e7c1 100644
--- a/include/hw/i2c/aspeed_i2c.h
+++ b/include/hw/i2c/aspeed_i2c.h
@@ -30,6 +30,7 @@
#define TYPE_ASPEED_2500_I2C TYPE_ASPEED_I2C "-ast2500"
#define TYPE_ASPEED_2600_I2C TYPE_ASPEED_I2C "-ast2600"
#define TYPE_ASPEED_1030_I2C TYPE_ASPEED_I2C "-ast1030"
+#define TYPE_ASPEED_1040_I2C TYPE_ASPEED_I2C "-ast1040"
#define TYPE_ASPEED_2700_I2C TYPE_ASPEED_I2C "-ast2700"
OBJECT_DECLARE_TYPE(AspeedI2CState, AspeedI2CClass, ASPEED_I2C)
diff --git a/hw/i2c/aspeed_i2c.c b/hw/i2c/aspeed_i2c.c
index 5be6fefc4d..8418a0a686 100644
--- a/hw/i2c/aspeed_i2c.c
+++ b/hw/i2c/aspeed_i2c.c
@@ -1702,6 +1702,34 @@ static const TypeInfo aspeed_1030_i2c_info = {
.class_init = aspeed_1030_i2c_class_init,
};
+static void aspeed_1040_i2c_class_init(ObjectClass *klass, const void *data)
+{
+ DeviceClass *dc = DEVICE_CLASS(klass);
+ AspeedI2CClass *aic = ASPEED_I2C_CLASS(klass);
+
+ dc->desc = "ASPEED 1040 I2C Controller";
+
+ aic->num_busses = 16;
+ aic->reg_size = 0xa0;
+ aic->reg_gap_size = 0x60;
+ aic->gap = -1; /* no gap */
+ aic->bus_get_irq = aspeed_2600_i2c_bus_get_irq;
+ aic->pool_size = 0x40;
+ aic->pool_gap_size = 0xc0;
+ aic->pool_base = 0x1c0;
+ aic->bus_pool_base = aspeed_2500_i2c_bus_pool_base;
+ aic->has_dma = true;
+ aic->mem_size = 0x2000;
+ aic->has_dma64 = true;
+ aic->dma_addr_lo_mask = 0x00ffffff;
+}
+
+static const TypeInfo aspeed_1040_i2c_info = {
+ .name = TYPE_ASPEED_1040_I2C,
+ .parent = TYPE_ASPEED_I2C,
+ .class_init = aspeed_1040_i2c_class_init,
+};
+
static void aspeed_2700_i2c_class_init(ObjectClass *klass, const void *data)
{
DeviceClass *dc = DEVICE_CLASS(klass);
@@ -1739,6 +1767,7 @@ static void aspeed_i2c_register_types(void)
type_register_static(&aspeed_2500_i2c_info);
type_register_static(&aspeed_2600_i2c_info);
type_register_static(&aspeed_1030_i2c_info);
+ type_register_static(&aspeed_1040_i2c_info);
type_register_static(&aspeed_2700_i2c_info);
}
--
2.43.0
next prev parent reply other threads:[~2026-05-29 6:45 UTC|newest]
Thread overview: 26+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-05-29 6:42 [PATCH v1 00/10] hw/arm: Add AST1040 peripheral support Jamin Lin
2026-05-29 6:42 ` [PATCH v1 01/10] hw/i2c/aspeed_i2c: Introduce dma_addr_lo_mask to unify DMA address handling Jamin Lin
2026-06-01 12:51 ` Cédric Le Goater
2026-06-02 3:12 ` Jamin Lin
2026-05-29 6:42 ` [PATCH v1 02/10] hw/i2c/aspeed_i2c: Increase AST2700 buffer mode size and adjust offset Jamin Lin
2026-06-01 12:50 ` Cédric Le Goater
2026-06-02 2:54 ` Jamin Lin
2026-05-29 6:42 ` [PATCH v1 03/10] hw/arm/aspeed_ast1040: Reuse AST2700 ADC model Jamin Lin
2026-06-01 12:52 ` Cédric Le Goater
2026-05-29 6:42 ` [PATCH v1 04/10] hw/arm/aspeed_ast1040: Introduce PECI support Jamin Lin
2026-06-01 12:52 ` Cédric Le Goater
2026-05-29 6:42 ` [PATCH v1 05/10] hw/arm/aspeed_ast1040: Reuse AST2700 GPIO controller model Jamin Lin
2026-06-01 12:52 ` Cédric Le Goater
2026-05-29 6:42 ` [PATCH v1 06/10] hw/arm/aspeed_ast1040: Add SGPIO controller support Jamin Lin
2026-06-01 12:54 ` Cédric Le Goater
2026-05-29 6:42 ` Jamin Lin [this message]
2026-06-01 12:57 ` [PATCH v1 07/10] hw/i2c/aspeed_i2c: Introduce AST1040 I2C model Cédric Le Goater
2026-06-02 3:34 ` Jamin Lin
2026-05-29 6:42 ` [PATCH v1 08/10] hw/arm/aspeed_ast1040: Introduce I2C support Jamin Lin
2026-06-01 13:00 ` Cédric Le Goater
2026-06-02 3:45 ` Jamin Lin
2026-05-29 6:42 ` [PATCH v1 09/10] hw/arm/aspeed_ast1040_evb: Introduce onboard I2C device Jamin Lin
2026-06-01 13:02 ` Cédric Le Goater
2026-06-02 3:47 ` Jamin Lin
2026-05-29 6:42 ` [PATCH v1 10/10] hw/arm/aspeed_ast1040: Reuse AST2700 watchdog models Jamin Lin
2026-06-01 13:03 ` Cédric Le Goater
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20260529064243.2064188-8-jamin_lin@aspeedtech.com \
--to=jamin_lin@aspeedtech.com \
--cc=andrew@codeconstruct.com.au \
--cc=clg@kaod.org \
--cc=joel@jms.id.au \
--cc=kane_chen@aspeedtech.com \
--cc=leetroy@gmail.com \
--cc=peter.maydell@linaro.org \
--cc=qemu-arm@nongnu.org \
--cc=qemu-devel@nongnu.org \
--cc=steven_lee@aspeedtech.com \
--cc=troy_lee@aspeedtech.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox