QEMU-Arm Archive on lore.kernel.org
 help / color / mirror / Atom feed
From: Jamin Lin <jamin_lin@aspeedtech.com>
To: "Cédric Le Goater" <clg@kaod.org>,
	"Peter Maydell" <peter.maydell@linaro.org>,
	"Steven Lee" <steven_lee@aspeedtech.com>,
	"Troy Lee" <leetroy@gmail.com>,
	"Kane Chen" <kane_chen@aspeedtech.com>,
	"Andrew Jeffery" <andrew@codeconstruct.com.au>,
	"Joel Stanley" <joel@jms.id.au>,
	"open list:ASPEED BMCs" <qemu-arm@nongnu.org>,
	"open list:All patches CC here" <qemu-devel@nongnu.org>
Cc: Jamin Lin <jamin_lin@aspeedtech.com>, Troy Lee <troy_lee@aspeedtech.com>
Subject: [PATCH v2 01/10] hw/i2c/aspeed_i2c: Introduce dma_addr_lo_mask to unify DMA address handling
Date: Tue, 2 Jun 2026 05:28:29 +0000	[thread overview]
Message-ID: <20260602052827.1535299-2-jamin_lin@aspeedtech.com> (raw)
In-Reply-To: <20260602052827.1535299-1-jamin_lin@aspeedtech.com>

The Aspeed I2C controller has two register layouts.

The AST2500 uses the old mode with a single DMA address register (I2CD_DMA_ADDR)
where the address is 4-byte aligned and masked to 0x3ffffffc.

From AST2600 onwards, the new mode provides separate master TX/RX and slave RX DMA
address registers (I2CM_DMA_TX_ADDR, I2CM_DMA_RX_ADDR, I2CS_DMA_RX_ADDR)
with different address widths per SoC:
  AST2600 (new mode): 0x7fffffff  - bits[30:0]
  AST1030 (new mode): 0x7fffffff  - bits[30:0]
  AST1060 (new mode): 0x7fffffff  - bits[30:0]
  AST2700 (new mode): 0xffffffff  - bits[31:0]

Introduce dma_addr_lo_mask as a per-class attribute and apply it
uniformly when storing DMA address register writes and when loading
the address into dma_dram_offset for both master and slave paths.
This replaces the previous FIELD_EX32 extractions (which incorrectly
stripped bit 31 on AST2700) and the hardcoded 0x3ffffffc literal in
the old-mode path.

Fixes: 1809ab6a67359e0876981cd05d2a50b2843eabad ("hw/i2c/aspeed: Add AST2700 support")
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
---
 include/hw/i2c/aspeed_i2c.h |  5 +----
 hw/i2c/aspeed_i2c.c         | 22 +++++++++++++---------
 2 files changed, 14 insertions(+), 13 deletions(-)

diff --git a/include/hw/i2c/aspeed_i2c.h b/include/hw/i2c/aspeed_i2c.h
index d42cb4865a..1fc229f699 100644
--- a/include/hw/i2c/aspeed_i2c.h
+++ b/include/hw/i2c/aspeed_i2c.h
@@ -209,13 +209,9 @@ REG32(I2CS_DMA_LEN, 0x2c)
     FIELD(I2CS_DMA_LEN, TX_BUF_LEN_W1T, 15, 1)
     FIELD(I2CS_DMA_LEN, TX_BUF_LEN, 0, 11)
 REG32(I2CM_DMA_TX_ADDR, 0x30)
-    FIELD(I2CM_DMA_TX_ADDR, ADDR, 0, 31)
 REG32(I2CM_DMA_RX_ADDR, 0x34)
-    FIELD(I2CM_DMA_RX_ADDR, ADDR, 0, 31)
 REG32(I2CS_DMA_TX_ADDR, 0x38)
-    FIELD(I2CS_DMA_TX_ADDR, ADDR, 0, 31)
 REG32(I2CS_DMA_RX_ADDR, 0x3c)
-    FIELD(I2CS_DMA_RX_ADDR, ADDR, 0, 31)
 REG32(I2CS_DEV_ADDR, 0x40)
 REG32(I2CM_DMA_LEN_STS, 0x48)
     FIELD(I2CM_DMA_LEN_STS, RX_LEN, 16, 13)
@@ -303,6 +299,7 @@ struct AspeedI2CClass {
     bool has_share_pool;
     uint64_t mem_size;
     bool has_dma64;
+    uint32_t dma_addr_lo_mask;
 };
 
 static inline bool aspeed_i2c_is_new_mode(AspeedI2CState *s)
diff --git a/hw/i2c/aspeed_i2c.c b/hw/i2c/aspeed_i2c.c
index 4a6732a185..a6b44174f5 100644
--- a/hw/i2c/aspeed_i2c.c
+++ b/hw/i2c/aspeed_i2c.c
@@ -236,7 +236,7 @@ static void aspeed_i2c_set_tx_dma_dram_offset(AspeedI2CBus *bus)
         value = bus->regs[R_I2CM_DMA_TX_ADDR];
         bus->dma_dram_offset =
             deposit64(bus->dma_dram_offset, 0, 32,
-                      FIELD_EX32(value, I2CM_DMA_TX_ADDR, ADDR));
+                      value & aic->dma_addr_lo_mask);
         if (aic->has_dma64) {
             value = bus->regs[R_I2CM_DMA_TX_ADDR_HI];
             bus->dma_dram_offset =
@@ -246,7 +246,7 @@ static void aspeed_i2c_set_tx_dma_dram_offset(AspeedI2CBus *bus)
     } else {
         value = bus->regs[R_I2CD_DMA_ADDR];
         bus->dma_dram_offset = deposit64(bus->dma_dram_offset, 0, 32,
-                                         value & 0x3ffffffc);
+                                         value & aic->dma_addr_lo_mask);
     }
 }
 
@@ -261,7 +261,7 @@ static void aspeed_i2c_set_rx_dma_dram_offset(AspeedI2CBus *bus)
         value = bus->regs[R_I2CM_DMA_RX_ADDR];
         bus->dma_dram_offset =
             deposit64(bus->dma_dram_offset, 0, 32,
-                      FIELD_EX32(value, I2CM_DMA_RX_ADDR, ADDR));
+                      value & aic->dma_addr_lo_mask);
         if (aic->has_dma64) {
             value = bus->regs[R_I2CM_DMA_RX_ADDR_HI];
             bus->dma_dram_offset =
@@ -271,7 +271,7 @@ static void aspeed_i2c_set_rx_dma_dram_offset(AspeedI2CBus *bus)
     } else {
         value = bus->regs[R_I2CD_DMA_ADDR];
         bus->dma_dram_offset = deposit64(bus->dma_dram_offset, 0, 32,
-                                         value & 0x3ffffffc);
+                                         value & aic->dma_addr_lo_mask);
     }
 }
 
@@ -735,12 +735,10 @@ static void aspeed_i2c_bus_new_write(AspeedI2CBus *bus, hwaddr offset,
         aspeed_i2c_bus_raise_interrupt(bus);
         break;
     case A_I2CM_DMA_TX_ADDR:
-        bus->regs[R_I2CM_DMA_TX_ADDR] = FIELD_EX32(value, I2CM_DMA_TX_ADDR,
-                                                   ADDR);
+        bus->regs[R_I2CM_DMA_TX_ADDR] = value & aic->dma_addr_lo_mask;
         break;
     case A_I2CM_DMA_RX_ADDR:
-        bus->regs[R_I2CM_DMA_RX_ADDR] = FIELD_EX32(value, I2CM_DMA_RX_ADDR,
-                                                   ADDR);
+        bus->regs[R_I2CM_DMA_RX_ADDR] = value & aic->dma_addr_lo_mask;
         break;
     case A_I2CM_DMA_LEN:
         w1t = FIELD_EX32(value, I2CM_DMA_LEN, RX_BUF_LEN_W1T) ||
@@ -1375,6 +1373,8 @@ static void aspeed_i2c_class_init(ObjectClass *klass, const void *data)
 static int aspeed_i2c_bus_new_slave_event(AspeedI2CBus *bus,
                                           enum i2c_event event)
 {
+    AspeedI2CClass *aic = ASPEED_I2C_GET_CLASS(bus->controller);
+
     switch (event) {
     case I2C_START_SEND_ASYNC:
         if (!SHARED_ARRAY_FIELD_EX32(bus->regs, R_I2CS_CMD, RX_DMA_EN)) {
@@ -1385,7 +1385,7 @@ static int aspeed_i2c_bus_new_slave_event(AspeedI2CBus *bus,
         ARRAY_FIELD_DP32(bus->regs, I2CS_DMA_LEN_STS, RX_LEN, 0);
         bus->dma_dram_offset =
             deposit64(bus->dma_dram_offset, 0, 32,
-                      ARRAY_FIELD_EX32(bus->regs, I2CS_DMA_RX_ADDR, ADDR));
+                      bus->regs[R_I2CS_DMA_RX_ADDR] & aic->dma_addr_lo_mask);
         bus->regs[R_I2CC_DMA_LEN] =
             ARRAY_FIELD_EX32(bus->regs, I2CS_DMA_LEN, RX_BUF_LEN) + 1;
         i2c_ack(bus->bus);
@@ -1608,6 +1608,7 @@ static void aspeed_2500_i2c_class_init(ObjectClass *klass, const void *data)
     aic->check_sram = true;
     aic->has_dma = true;
     aic->mem_size = 0x1000;
+    aic->dma_addr_lo_mask = 0x3ffffffc;
 }
 
 static qemu_irq aspeed_2600_i2c_bus_get_irq(AspeedI2CBus *bus)
@@ -1631,6 +1632,7 @@ static void aspeed_2600_i2c_class_init(ObjectClass *klass, const void *data)
     aic->bus_pool_base = aspeed_2500_i2c_bus_pool_base;
     aic->has_dma = true;
     aic->mem_size = 0x1000;
+    aic->dma_addr_lo_mask = 0x7fffffff;
 }
 
 static void aspeed_1030_i2c_class_init(ObjectClass *klass, const void *data)
@@ -1649,6 +1651,7 @@ static void aspeed_1030_i2c_class_init(ObjectClass *klass, const void *data)
     aic->bus_pool_base = aspeed_2500_i2c_bus_pool_base;
     aic->has_dma = true;
     aic->mem_size = 0x10000;
+    aic->dma_addr_lo_mask = 0x7fffffff;
 }
 
 static void aspeed_2700_i2c_class_init(ObjectClass *klass, const void *data)
@@ -1670,6 +1673,7 @@ static void aspeed_2700_i2c_class_init(ObjectClass *klass, const void *data)
     aic->has_dma = true;
     aic->mem_size = 0x2000;
     aic->has_dma64 = true;
+    aic->dma_addr_lo_mask = 0xffffffff;
 }
 
 static const TypeInfo aspeed_i2c_types[] = {
-- 
2.43.0


  reply	other threads:[~2026-06-02  5:30 UTC|newest]

Thread overview: 19+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2026-06-02  5:28 [PATCH v2 00/10] hw/arm/aspeed: Add AST1040 peripheral support Jamin Lin
2026-06-02  5:28 ` Jamin Lin [this message]
2026-06-02  6:26   ` [PATCH v2 01/10] hw/i2c/aspeed_i2c: Introduce dma_addr_lo_mask to unify DMA address handling Cédric Le Goater
2026-06-03  2:58     ` Jamin Lin
2026-06-02  5:28 ` [PATCH v2 02/10] hw/i2c/aspeed_i2c: Increase AST2700 buffer mode size and adjust offset Jamin Lin
2026-06-02  6:33   ` Cédric Le Goater
2026-06-02  8:22     ` Jamin Lin
2026-06-02  5:28 ` [PATCH v2 03/10] hw/arm/aspeed_ast1040: Reuse AST2700 ADC model Jamin Lin
2026-06-02  5:28 ` [PATCH v2 04/10] hw/arm/aspeed_ast1040: Introduce PECI support Jamin Lin
2026-06-02  5:28 ` [PATCH v2 05/10] hw/arm/aspeed_ast1040: Reuse AST2700 GPIO controller model Jamin Lin
2026-06-02  5:28 ` [PATCH v2 06/10] hw/arm/aspeed_ast1040: Add SGPIO controller support Jamin Lin
2026-06-02  5:28 ` [PATCH v2 07/10] hw/i2c/aspeed_i2c: Introduce AST1040 I2C model Jamin Lin
2026-06-02  5:28 ` [PATCH v2 08/10] hw/arm/aspeed_ast1040: Introduce I2C support Jamin Lin
2026-06-02  6:33   ` Cédric Le Goater
2026-06-02  8:41     ` Jamin Lin
2026-06-02  5:28 ` [PATCH v2 09/10] hw/arm/aspeed_ast1040_evb: Introduce onboard I2C device Jamin Lin
2026-06-02  6:34   ` Cédric Le Goater
2026-06-03  1:31     ` Jamin Lin
2026-06-02  5:28 ` [PATCH v2 10/10] hw/arm/aspeed_ast1040: Reuse AST2700 watchdog models Jamin Lin

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20260602052827.1535299-2-jamin_lin@aspeedtech.com \
    --to=jamin_lin@aspeedtech.com \
    --cc=andrew@codeconstruct.com.au \
    --cc=clg@kaod.org \
    --cc=joel@jms.id.au \
    --cc=kane_chen@aspeedtech.com \
    --cc=leetroy@gmail.com \
    --cc=peter.maydell@linaro.org \
    --cc=qemu-arm@nongnu.org \
    --cc=qemu-devel@nongnu.org \
    --cc=steven_lee@aspeedtech.com \
    --cc=troy_lee@aspeedtech.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox