* [PATCH v5 1/8] ARM: zte: Add zx297520v3 platform support
2026-04-21 20:23 [PATCH v5 0/8] Add support for ZTE zx297520v3 Stefan Dösinger
@ 2026-04-21 20:23 ` Stefan Dösinger
2026-04-21 20:23 ` [PATCH v5 2/8] dt-bindings: arm: Add zx297520v3 board binding Stefan Dösinger
` (6 subsequent siblings)
7 siblings, 0 replies; 14+ messages in thread
From: Stefan Dösinger @ 2026-04-21 20:23 UTC (permalink / raw)
To: Jonathan Corbet, Shuah Khan, Russell King, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Arnd Bergmann,
Krzysztof Kozlowski, Alexandre Belloni, Linus Walleij,
Drew Fustini, Greg Kroah-Hartman, Jiri Slaby
Cc: linux-doc, linux-kernel, linux-arm-kernel, devicetree, soc,
linux-serial, Stefan Dösinger
This SoC is used in low end LTE-to-WiFi routers, for example some D-Link
DWR 932 revisions, ZTE K10, ZLT S10 4G, but also models that are branded
and sold by ISPs themselves. They are widespread in Africa, China,
Russia and Eastern Europe.
This SoC is a relative of the zx296702 and zx296718 that had some
upstream support until commit 89d4f98ae90d ("ARM: remove zte zx
platform"). My eventual goal is to enable OpenWRT to run on these
devices.
Signed-off-by: Stefan Dösinger <stefandoesinger@gmail.com>
---
Documentation/arch/arm/zte/zx297520v3.rst | 158 ++++++++++++++++++++++++++++++
MAINTAINERS | 4 +
arch/arm/Kconfig | 2 +
arch/arm/Makefile | 1 +
arch/arm/mach-zte/Kconfig | 26 +++++
arch/arm/mach-zte/Makefile | 2 +
arch/arm/mach-zte/zx297520v3.c | 19 ++++
7 files changed, 212 insertions(+)
diff --git a/Documentation/arch/arm/zte/zx297520v3.rst b/Documentation/arch/arm/zte/zx297520v3.rst
new file mode 100644
index 000000000000..6621ea72769f
--- /dev/null
+++ b/Documentation/arch/arm/zte/zx297520v3.rst
@@ -0,0 +1,158 @@
+.. SPDX-License-Identifier: GPL-2.0-only
+
+====================================
+Booting Linux on ZTE zx297520v3 SoCs
+====================================
+
+...............................................................................
+
+Author: Stefan Dösinger
+
+Date : 27 Jan 2026
+
+1. Hardware description
+---------------------------
+Zx297520v3 SoCs use a 64 bit capable Cortex-A53 CPU and GICv3, although they
+run in arm32 mode only. The CPU has support EL3, but no hypervisor (EL2) and
+it seems to lack VFP and NEON.
+
+The SoC is used in a number of cheap LTE to WiFi routers, both battery powered
+MiFis and stationary CPEs. In addition to the CPU these devices usually have
+64 MB Ram (although some is shared with the LTE chip), 128 MB NAND flash, an
+SDIO connected RTL8192-type Wifi chip limited to 2.4 ghz operation, USB 2,
+and buttons. Devices with as low as 32 MB or as high as 128 MB ram exist, as
+do devices with 8 or 16 MB of NOR flash.
+
+Some devices, especially the stationary ones, have 100 mbit Ethernet and an
+Ethernet switch.
+
+Usually the devices have LEDs for status indication, although some have SPI or
+I2C connected displays
+
+Some have an SD card slot. If it exists, it is a better choice for the root
+file system because it easily outperforms the built-in NAND.
+
+The LTE interface runs on a separate DSP called ZSP880. It is probably derived
+from LSI ZSPs and has an undocumented instruction set. The ZSP communicates
+with the main CPU via SRAM and DRAM and a mailbox hardware that can generate
+IRQs on either ends.
+
+There is also a Cortex M0 CPU, which is responsible for early HW initialization
+and starting the Cortex A53 CPU. It does not have any essential purpose once
+U-Boot is started. A SRAM-Based handover protocol exists to run custom code on
+this CPU.
+
+2. Booting via USB
+---------------------------
+
+The Boot ROM has support for booting custom code via USB. This mode can be
+entered by connecting a Boot PIN to GND or by modifying the third byte on NAND
+(set it to anything other than 0x5A aka 'Z'). A free software tool to start
+custom U-Boot and kernels can be found here:
+
+https://github.com/zx297520v3-mainline/zx297520v3-loader
+
+If USB download mode is entered but no boot commands are sent through USB, the
+device will proceed to boot normally after a few seconds. It is therefore
+possible to enable USB boot permanently and still leave the default boot files
+in place.
+
+3. Building for built-in U-Boot
+---------------------------
+The devices come with an ancient U-Boot that loads legacy uImages from NAND and
+boots them without a chance for the user to interrupt. The images are stored in
+files ap_cpuap.bin and ap_recovery.bin on a jffs2 partition named imagefs,
+usually mtd4. A file named "fotaflag" switches between the two modes.
+
+In addition to the uImage header, those files have a 384 byte signature header,
+which is used for authenticating the images on some devices. Most devices have
+this authentication disabled and it is enough to pad the uImage files with 384
+zero bytes.
+
+Builtin U-Boot also poorly sets up the CPU. Read the next section for details
+on this. It has no support for loading DTBs, so CONFIG_ARM_APPENDED_DTB is
+needed.
+
+So to build an image that boots from NAND the following steps are necessary:
+
+1) Patch the assembly code from section 3 into arch/arm/kernel/head.S.
+2) make zx29_defconfig
+3) make [-j x]
+4) cat arch/arm/boot/zImage arch/arm/boot/dts/zte/[device].dtb > kernel+dtb
+5) mkimage -A arm -O linux -T kernel -C none -a 0x20008000 -d kernel+dtb uimg
+6) dd if=/dev/zero bs=1 count=384 of=ap_recovery.bin
+7) cat uimg >> ap_recovery.bin
+8) Place this file onto imagefs on the device. Delete ap_cpuap.bin if the
+free space is not enough.
+9) Create the file fotaflag: echo -n FOTA-RECOVERY > fotaflag
+
+For development, booting ap_recovery.bin is recommended because the normal boot
+mode arms the watchdog before starting the kernel.
+
+4. CPU and GIC Setup
+---------------------------
+
+Generally CPU and GICv3 need to be set up according to the requirements spelled
+out in Documentation/arch/arm64/booting.rst. For zx297520v3 this means:
+
+1. GICD_CTLR.DS=1 to disable GIC security
+2. Enable access to ICC_SRE
+3. Disable trapping IRQs into monitor mode
+4. Configure EL2 and below to run in insecure mode.
+5. Configure timer PPIs to active-low.
+
+The kernel sources provided by ZTE do not boot either (interrupts do not work
+at all). They are incomplete in other aspects too, so it is assumed that there
+is some workaround similar to the one described in this document somewhere in
+the binary blobs.
+
+The assembly code below is given as an example of how to achieve this:
+
+```
+#include <linux/irqchip/arm-gic-v3.h>
+#include <asm/assembler.h>
+#include <asm/cp15.h>
+
+@ This allows EL1 to handle ints hat are normally handled by EL2/3.
+ldr r3, =0xf2000000
+ldr r4, =(GICD_CTLR_ARE_NS | GICD_CTLR_DS)
+str r4, [r3]
+
+cps #MON_MODE
+
+@ Work in non-secure physical address space: SCR_EL3.NS = 1. At least the UART
+@ seems to respond only to non-secure addresses. I have taken insipiration from
+@ Raspberry pi's armstub7.S here.
+@
+@ ARM docs say modify this bit in monitor mode only...
+mov r3, #0x131 @ non-secure, Make F, A bits in CPSR writeable
+ @ Allow hypervisor call.
+mcr p15, 0, r3, c1, c1, 0
+
+@ AP_PPI_MODE_REG: Configure timer PPIs (10, 11, 13, 14) to active-low.
+ldr r3, =0xF22020a8
+ldr r4, =0x50
+str r4, [r3]
+ldr r3, =0xF22020ac
+ldr r4, =0x14
+str r4, [r3]
+
+@ Enable EL2 access to ICC_SRE (bit 3, ICC_SRE_EL3.Enable). Enable system reg
+@ access to GICv3 registers (bit 0, ICC_SRE_EL3.SRE) for EL1 and EL3.
+mrc p15, 6, r3, c12, c12, 5 @ ICC_SRE_EL3
+orr r3, #0x9 @ FIXME: No defines for SRE_EL3 values?
+mcr p15, 6, r3, c12, c12, 5
+mrc p15, 0, r3, c12, c12, 5 @ ICC_SRE_EL1
+orr r3, #(ICC_SRE_EL1_SRE)
+mcr p15, 0, r3, c12, c12, 5
+
+@ Like ICC_SRE_EL3, enable EL1 access to ICC_SRE and system register access
+@ for EL2.
+mrc p15, 4, r3, c12, c9, 5 @ ICC_SRE_EL2 aka ICC_HSRE
+orr r3, r3, #(ICC_SRE_EL2_ENABLE | ICC_SRE_EL2_SRE)
+mcr p15, 4, r3, c12, c9, 5
+isb
+
+@ Back to SVC mode. TODO: Doesn't safe_svcmode_maskall do this for us anyway?
+cps #SVC_MODE
+```
diff --git a/MAINTAINERS b/MAINTAINERS
index d1cc0e12fe1f..974d7a98956a 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -29200,6 +29200,10 @@ F: include/linux/zswap.h
F: mm/zswap.c
F: tools/testing/selftests/cgroup/test_zswap.c
+ZX29
+M: Stefan Dösinger <stefandoesinger@gmail.com>
+F: arch/arm/mach-zte/
+
SENARYTECH AUDIO CODEC DRIVER
M: bo liu <bo.liu@senarytech.com>
S: Maintained
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index ec33376f8e2b..4217ed704e48 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -464,6 +464,8 @@ source "arch/arm/mach-versatile/Kconfig"
source "arch/arm/mach-vt8500/Kconfig"
+source "arch/arm/mach-zte/Kconfig"
+
source "arch/arm/mach-zynq/Kconfig"
# ARMv7-M architecture
diff --git a/arch/arm/Makefile b/arch/arm/Makefile
index b7de4b6b284c..573813ef5e77 100644
--- a/arch/arm/Makefile
+++ b/arch/arm/Makefile
@@ -223,6 +223,7 @@ machine-$(CONFIG_ARCH_SUNXI) += sunxi
machine-$(CONFIG_ARCH_TEGRA) += tegra
machine-$(CONFIG_ARCH_U8500) += ux500
machine-$(CONFIG_ARCH_VT8500) += vt8500
+machine-$(CONFIG_ARCH_ZTE) += zte
machine-$(CONFIG_ARCH_ZYNQ) += zynq
machine-$(CONFIG_PLAT_VERSATILE) += versatile
machine-$(CONFIG_PLAT_SPEAR) += spear
diff --git a/arch/arm/mach-zte/Kconfig b/arch/arm/mach-zte/Kconfig
new file mode 100644
index 000000000000..2e3abee94994
--- /dev/null
+++ b/arch/arm/mach-zte/Kconfig
@@ -0,0 +1,26 @@
+# SPDX-License-Identifier: GPL-2.0-only
+menuconfig ARCH_ZTE
+ bool "ZTE zx family"
+ depends on ARCH_MULTI_V7
+ help
+ Support for ZTE zx-based family of processors.
+
+if ARCH_ZTE
+
+config SOC_ZX297520V3
+ default y if ARCH_ZTE
+ bool "zx297520v3"
+ select ARM_GIC_V3
+ select ARM_AMBA
+ select HAVE_ARM_ARCH_TIMER
+ select PM_GENERIC_DOMAINS if PM
+ help
+ Support for ZTE zx297520v3 SoC. It is a single core SoC used in cheap
+ LTE to WiFi routers. These devices can be identified by the occurrence
+ of the string "zx297520v3" in the boot output and /proc/cpuinfo of
+ their stock firmware.
+
+ Please read Documentation/arch/arm/zte/zx297520v3.rst on how to boot
+ the kernel.
+
+endif
diff --git a/arch/arm/mach-zte/Makefile b/arch/arm/mach-zte/Makefile
new file mode 100644
index 000000000000..1bfe4fddd6af
--- /dev/null
+++ b/arch/arm/mach-zte/Makefile
@@ -0,0 +1,2 @@
+# SPDX-License-Identifier: GPL-2.0-only
+obj-$(CONFIG_SOC_ZX297520V3) += zx297520v3.o
diff --git a/arch/arm/mach-zte/zx297520v3.c b/arch/arm/mach-zte/zx297520v3.c
new file mode 100644
index 000000000000..c11c7e836f91
--- /dev/null
+++ b/arch/arm/mach-zte/zx297520v3.c
@@ -0,0 +1,19 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright 2026 Stefan Dösinger
+ */
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+
+#include <linux/of_address.h>
+#include <linux/of_platform.h>
+
+static const char *const zx297520v3_dt_compat[] __initconst = {
+ "zte,zx297520v3",
+ NULL,
+};
+
+DT_MACHINE_START(ZX, "ZTE zx297520v3 (Device Tree)")
+ .dt_compat = zx297520v3_dt_compat,
+MACHINE_END
--
2.53.0
^ permalink raw reply related [flat|nested] 14+ messages in thread* [PATCH v5 2/8] dt-bindings: arm: Add zx297520v3 board binding
2026-04-21 20:23 [PATCH v5 0/8] Add support for ZTE zx297520v3 Stefan Dösinger
2026-04-21 20:23 ` [PATCH v5 1/8] ARM: zte: Add zx297520v3 platform support Stefan Dösinger
@ 2026-04-21 20:23 ` Stefan Dösinger
2026-04-22 7:06 ` Krzysztof Kozlowski
2026-04-21 20:23 ` [PATCH v5 3/8] ARM: dts: Add D-Link DWR-932M support Stefan Dösinger
` (5 subsequent siblings)
7 siblings, 1 reply; 14+ messages in thread
From: Stefan Dösinger @ 2026-04-21 20:23 UTC (permalink / raw)
To: Jonathan Corbet, Shuah Khan, Russell King, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Arnd Bergmann,
Krzysztof Kozlowski, Alexandre Belloni, Linus Walleij,
Drew Fustini, Greg Kroah-Hartman, Jiri Slaby
Cc: linux-doc, linux-kernel, linux-arm-kernel, devicetree, soc,
linux-serial, Stefan Dösinger
Add a compatible for boards based on the ZTE zx297520v3 SoC.
Signed-off-by: Stefan Dösinger <stefandoesinger@gmail.com>
---
The list of devices is the devices I have access to for testing. There
are many more devices based on this board and it is not always easy to
identify them. Often they are sold without any branding ("4G home
router") or with mobile carrier branding.
---
Documentation/devicetree/bindings/arm/zte.yaml | 25 +++++++++++++++++++++++++
MAINTAINERS | 1 +
2 files changed, 26 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/zte.yaml b/Documentation/devicetree/bindings/arm/zte.yaml
new file mode 100644
index 000000000000..4b0d6d53402b
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/zte.yaml
@@ -0,0 +1,25 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/arm/zte.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: ZTE zx29
+
+maintainers:
+ - Stefan Dösinger <stefandoesinger@gmail.com>
+
+properties:
+ $nodename:
+ const: "/"
+ compatible:
+ oneOf:
+ - items:
+ - enum:
+ - dlink,dwr932m
+ - hgsd,r310
+ - tecno,tr118
+ - zte,k10
+ - const: zte,zx297520v3
+
+additionalProperties: true
diff --git a/MAINTAINERS b/MAINTAINERS
index 974d7a98956a..bcade90ca14e 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -29202,6 +29202,7 @@ F: tools/testing/selftests/cgroup/test_zswap.c
ZX29
M: Stefan Dösinger <stefandoesinger@gmail.com>
+F: Documentation/devicetree/bindings/arm/zte.yaml
F: arch/arm/mach-zte/
SENARYTECH AUDIO CODEC DRIVER
--
2.53.0
^ permalink raw reply related [flat|nested] 14+ messages in thread* Re: [PATCH v5 2/8] dt-bindings: arm: Add zx297520v3 board binding
2026-04-21 20:23 ` [PATCH v5 2/8] dt-bindings: arm: Add zx297520v3 board binding Stefan Dösinger
@ 2026-04-22 7:06 ` Krzysztof Kozlowski
0 siblings, 0 replies; 14+ messages in thread
From: Krzysztof Kozlowski @ 2026-04-22 7:06 UTC (permalink / raw)
To: Stefan Dösinger
Cc: Jonathan Corbet, Shuah Khan, Russell King, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Arnd Bergmann,
Alexandre Belloni, Linus Walleij, Drew Fustini,
Greg Kroah-Hartman, Jiri Slaby, linux-doc, linux-kernel,
linux-arm-kernel, devicetree, soc, linux-serial
On Tue, Apr 21, 2026 at 11:23:10PM +0300, Stefan Dösinger wrote:
> +maintainers:
> + - Stefan Dösinger <stefandoesinger@gmail.com>
> +
> +properties:
> + $nodename:
> + const: "/"
> + compatible:
> + oneOf:
> + - items:
> + - enum:
> + - dlink,dwr932m
> + - hgsd,r310
> + - tecno,tr118
> + - zte,k10
Where are users of these bindings? We do not need unused ABI.
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH v5 3/8] ARM: dts: Add D-Link DWR-932M support
2026-04-21 20:23 [PATCH v5 0/8] Add support for ZTE zx297520v3 Stefan Dösinger
2026-04-21 20:23 ` [PATCH v5 1/8] ARM: zte: Add zx297520v3 platform support Stefan Dösinger
2026-04-21 20:23 ` [PATCH v5 2/8] dt-bindings: arm: Add zx297520v3 board binding Stefan Dösinger
@ 2026-04-21 20:23 ` Stefan Dösinger
2026-04-22 7:09 ` Krzysztof Kozlowski
2026-04-21 20:23 ` [PATCH v5 4/8] ARM: zte: Add support for zx29 low level debug Stefan Dösinger
` (4 subsequent siblings)
7 siblings, 1 reply; 14+ messages in thread
From: Stefan Dösinger @ 2026-04-21 20:23 UTC (permalink / raw)
To: Jonathan Corbet, Shuah Khan, Russell King, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Arnd Bergmann,
Krzysztof Kozlowski, Alexandre Belloni, Linus Walleij,
Drew Fustini, Greg Kroah-Hartman, Jiri Slaby
Cc: linux-doc, linux-kernel, linux-arm-kernel, devicetree, soc,
linux-serial, Stefan Dösinger
This adds base DT definition for zx297520v3 and one board that consumes it.
Signed-off-by: Stefan Dösinger <stefandoesinger@gmail.com>
---
Changes in v5:
Prepend the SoC name in the device specific DTS filename.
---
MAINTAINERS | 1 +
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/zte/Makefile | 3 ++
arch/arm/boot/dts/zte/zx297520v3-dlink-dwr932m.dts | 18 ++++++++++
arch/arm/boot/dts/zte/zx297520v3.dtsi | 40 ++++++++++++++++++++++
5 files changed, 63 insertions(+)
diff --git a/MAINTAINERS b/MAINTAINERS
index bcade90ca14e..f7ca0d478e81 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -29203,6 +29203,7 @@ F: tools/testing/selftests/cgroup/test_zswap.c
ZX29
M: Stefan Dösinger <stefandoesinger@gmail.com>
F: Documentation/devicetree/bindings/arm/zte.yaml
+F: arch/arm/boot/dts/zte
F: arch/arm/mach-zte/
SENARYTECH AUDIO CODEC DRIVER
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index efe38eb25301..28fba538d552 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -39,3 +39,4 @@ subdir-y += unisoc
subdir-y += vt8500
subdir-y += xen
subdir-y += xilinx
+subdir-y += zte
diff --git a/arch/arm/boot/dts/zte/Makefile b/arch/arm/boot/dts/zte/Makefile
new file mode 100644
index 000000000000..f052cfbd636c
--- /dev/null
+++ b/arch/arm/boot/dts/zte/Makefile
@@ -0,0 +1,3 @@
+# SPDX-License-Identifier: GPL-2.0-only
+dtb-$(CONFIG_SOC_ZX297520V3) += \
+ zx297520v3-dlink-dwr932m.dtb
diff --git a/arch/arm/boot/dts/zte/zx297520v3-dlink-dwr932m.dts b/arch/arm/boot/dts/zte/zx297520v3-dlink-dwr932m.dts
new file mode 100644
index 000000000000..ac20215fddef
--- /dev/null
+++ b/arch/arm/boot/dts/zte/zx297520v3-dlink-dwr932m.dts
@@ -0,0 +1,18 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2026 Stefan Dösinger <stefandoesinger@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "zx297520v3.dtsi"
+
+/ {
+ model = "D-Link DWR-932M";
+ compatible = "dlink,dwr932m", "zte,zx297520v3";
+
+ memory@20000000 {
+ device_type = "memory";
+ reg = <0x20000000 0x04000000>;
+ };
+};
diff --git a/arch/arm/boot/dts/zte/zx297520v3.dtsi b/arch/arm/boot/dts/zte/zx297520v3.dtsi
new file mode 100644
index 000000000000..0fff00f910d6
--- /dev/null
+++ b/arch/arm/boot/dts/zte/zx297520v3.dtsi
@@ -0,0 +1,40 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2026 Stefan Dösinger <stefandoesinger@gmail.com>
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ reg = <0>;
+ };
+ };
+
+ soc {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "simple-bus";
+ interrupt-parent = <&gic>;
+ ranges;
+
+ gic: interrupt-controller@f2000000 {
+ compatible = "arm,gic-v3";
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0xf2000000 0x10000>,
+ <0xf2040000 0x20000>;
+ };
+ };
+};
--
2.53.0
^ permalink raw reply related [flat|nested] 14+ messages in thread* Re: [PATCH v5 3/8] ARM: dts: Add D-Link DWR-932M support
2026-04-21 20:23 ` [PATCH v5 3/8] ARM: dts: Add D-Link DWR-932M support Stefan Dösinger
@ 2026-04-22 7:09 ` Krzysztof Kozlowski
0 siblings, 0 replies; 14+ messages in thread
From: Krzysztof Kozlowski @ 2026-04-22 7:09 UTC (permalink / raw)
To: Stefan Dösinger
Cc: Jonathan Corbet, Shuah Khan, Russell King, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Arnd Bergmann,
Alexandre Belloni, Linus Walleij, Drew Fustini,
Greg Kroah-Hartman, Jiri Slaby, linux-doc, linux-kernel,
linux-arm-kernel, devicetree, soc, linux-serial
On Tue, Apr 21, 2026 at 11:23:11PM +0300, Stefan Dösinger wrote:
> This adds base DT definition for zx297520v3 and one board that consumes it.
>
> Signed-off-by: Stefan Dösinger <stefandoesinger@gmail.com>
subject - missing zte prefix.
Please use subject prefixes matching the subsystem. You can get them for
example with 'git log --oneline -- DIRECTORY_OR_FILE' on the directory
your patch is touching. For bindings, the preferred subjects are
explained here:
https://www.kernel.org/doc/html/latest/devicetree/bindings/submitting-patches.html#i-for-patch-submitters
...
> +/ {
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + cpus {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + cpu@0 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53";
> + reg = <0>;
> + };
> + };
> +
> + soc {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + compatible = "simple-bus";
> + interrupt-parent = <&gic>;
> + ranges;
> +
> + gic: interrupt-controller@f2000000 {
> + compatible = "arm,gic-v3";
> + interrupt-controller;
> + #interrupt-cells = <3>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + reg = <0xf2000000 0x10000>,
> + <0xf2040000 0x20000>;
> + };
This is pretty incomplete DTS. The first submission must have a working,
basic device support which requires at least one interface, e.g. serial.
Otherwise how is this usable?
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH v5 4/8] ARM: zte: Add support for zx29 low level debug
2026-04-21 20:23 [PATCH v5 0/8] Add support for ZTE zx297520v3 Stefan Dösinger
` (2 preceding siblings ...)
2026-04-21 20:23 ` [PATCH v5 3/8] ARM: dts: Add D-Link DWR-932M support Stefan Dösinger
@ 2026-04-21 20:23 ` Stefan Dösinger
2026-04-21 20:23 ` [PATCH v5 5/8] ARM: dts: Add an armv7 timer for zx297520v3 Stefan Dösinger
` (3 subsequent siblings)
7 siblings, 0 replies; 14+ messages in thread
From: Stefan Dösinger @ 2026-04-21 20:23 UTC (permalink / raw)
To: Jonathan Corbet, Shuah Khan, Russell King, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Arnd Bergmann,
Krzysztof Kozlowski, Alexandre Belloni, Linus Walleij,
Drew Fustini, Greg Kroah-Hartman, Jiri Slaby
Cc: linux-doc, linux-kernel, linux-arm-kernel, devicetree, soc,
linux-serial, Stefan Dösinger
This is based on the removed zx29 code. A separate (more complicated)
patch will re-add the register map to the pl011 serial driver.
Signed-off-by: Stefan Dösinger <stefandoesinger@gmail.com>
---
I am unsure about the virtual address. It doesn't seem to matter, as
long as it is a valid address. This address is based on the old removed
code. Is there a rule-of-thumb physical to virtual mapping I can use to
give a sensible default value?
---
arch/arm/Kconfig.debug | 12 ++++++++++++
arch/arm/include/debug/pl01x.S | 7 +++++++
2 files changed, 19 insertions(+)
diff --git a/arch/arm/Kconfig.debug b/arch/arm/Kconfig.debug
index 366f162e147d..98d8a5a60048 100644
--- a/arch/arm/Kconfig.debug
+++ b/arch/arm/Kconfig.debug
@@ -1331,6 +1331,16 @@ choice
This option selects UART0 on VIA/Wondermedia System-on-a-chip
devices, including VT8500, WM8505, WM8650 and WM8850.
+ config DEBUG_ZTE_ZX
+ bool "Kernel low-level debugging via zx29 UART"
+ select DEBUG_UART_PL01X
+ depends on ARCH_ZTE
+ help
+ Say Y here if you are enabling ZTE zx297520v3 SOC and need
+ debug UART support. This UART is a PL011 with different
+ register addresses. The UART for boot messages on zx29 boards
+ is usually UART1 and is operating at 921600 8N1.
+
config DEBUG_ZYNQ_UART0
bool "Kernel low-level debugging on Xilinx Zynq using UART0"
depends on ARCH_ZYNQ
@@ -1545,6 +1555,7 @@ config DEBUG_UART_8250
config DEBUG_UART_PHYS
hex "Physical base address of debug UART"
+ default 0x01408000 if DEBUG_ZTE_ZX
default 0x01c28000 if DEBUG_SUNXI_UART0
default 0x01c28400 if DEBUG_SUNXI_UART1
default 0x01d0c000 if DEBUG_DAVINCI_DA8XX_UART1
@@ -1701,6 +1712,7 @@ config DEBUG_UART_VIRT
default 0xf31004c0 if DEBUG_MESON_UARTAO
default 0xf4090000 if DEBUG_LPC32XX
default 0xf4200000 if DEBUG_GEMINI
+ default 0xf4708000 if DEBUG_ZTE_ZX
default 0xf6200000 if DEBUG_PXA_UART1
default 0xf7000000 if DEBUG_SUN9I_UART0
default 0xf7000000 if DEBUG_S3C64XX_UART && DEBUG_S3C_UART0
diff --git a/arch/arm/include/debug/pl01x.S b/arch/arm/include/debug/pl01x.S
index c7e02d0628bf..0c7bfa4c10db 100644
--- a/arch/arm/include/debug/pl01x.S
+++ b/arch/arm/include/debug/pl01x.S
@@ -8,6 +8,13 @@
*/
#include <linux/amba/serial.h>
+#ifdef CONFIG_DEBUG_ZTE_ZX
+#undef UART01x_DR
+#undef UART01x_FR
+#define UART01x_DR 0x04
+#define UART01x_FR 0x14
+#endif
+
#ifdef CONFIG_DEBUG_UART_PHYS
.macro addruart, rp, rv, tmp
ldr \rp, =CONFIG_DEBUG_UART_PHYS
--
2.53.0
^ permalink raw reply related [flat|nested] 14+ messages in thread* [PATCH v5 5/8] ARM: dts: Add an armv7 timer for zx297520v3
2026-04-21 20:23 [PATCH v5 0/8] Add support for ZTE zx297520v3 Stefan Dösinger
` (3 preceding siblings ...)
2026-04-21 20:23 ` [PATCH v5 4/8] ARM: zte: Add support for zx29 low level debug Stefan Dösinger
@ 2026-04-21 20:23 ` Stefan Dösinger
2026-04-22 7:10 ` Krzysztof Kozlowski
2026-04-21 20:23 ` [PATCH v5 6/8] amba/serial: amba-pl011: Bring back zx29 UART support Stefan Dösinger
` (2 subsequent siblings)
7 siblings, 1 reply; 14+ messages in thread
From: Stefan Dösinger @ 2026-04-21 20:23 UTC (permalink / raw)
To: Jonathan Corbet, Shuah Khan, Russell King, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Arnd Bergmann,
Krzysztof Kozlowski, Alexandre Belloni, Linus Walleij,
Drew Fustini, Greg Kroah-Hartman, Jiri Slaby
Cc: linux-doc, linux-kernel, linux-arm-kernel, devicetree, soc,
linux-serial, Stefan Dösinger
The stock kernel does not use this timer, but it seems to work fine. The
board has other board-specific timers that would need a driver and I see
no reason to bother with them since the arm standard timer works.
The caveat is the non-standard GIC setup needed to handle the timer's
level-low PPI. This is the responsibility of the boot loader and
documented in Documentation/arch/arm/zte/zx297520v3.rst.
Signed-off-by: Stefan Dösinger <stefandoesinger@gmail.com>
---
arch/arm/boot/dts/zte/zx297520v3.dtsi | 24 ++++++++++++++++++++++++
1 file changed, 24 insertions(+)
diff --git a/arch/arm/boot/dts/zte/zx297520v3.dtsi b/arch/arm/boot/dts/zte/zx297520v3.dtsi
index 0fff00f910d6..903050c684cb 100644
--- a/arch/arm/boot/dts/zte/zx297520v3.dtsi
+++ b/arch/arm/boot/dts/zte/zx297520v3.dtsi
@@ -20,6 +20,21 @@ cpu@0 {
};
};
+ timer {
+ compatible = "arm,armv7-timer";
+ interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>;
+ clock-frequency = <26000000>;
+ interrupt-parent = <&gic>;
+ /* I don't think uboot sets CNTVOFF and the stock kernel doesn't use the
+ * arm timer at all. Since this is a single CPU system I don't think it
+ * really matters that the offset is random though.
+ */
+ arm,cpu-registers-not-fw-configured;
+ };
+
soc {
#address-cells = <1>;
#size-cells = <1>;
@@ -27,6 +42,15 @@ soc {
interrupt-parent = <&gic>;
ranges;
+ /* The GIC has a non-standard way of configuring ints between level-low/level
+ * high or rising edge/falling edge at 0xf2202070 and onwards. See AP_INT_MODE_BASE
+ * and AP_PPI_MODE_REG in the ZTE kernel, although the offsets in the kernel source
+ * seem wrong.
+ *
+ * Everything defaults to active-high/rising edge, but the timer is active-low. We
+ * currently rely on the boot loader to change timer IRQs to active-low for us for
+ * now.
+ */
gic: interrupt-controller@f2000000 {
compatible = "arm,gic-v3";
interrupt-controller;
--
2.53.0
^ permalink raw reply related [flat|nested] 14+ messages in thread* Re: [PATCH v5 5/8] ARM: dts: Add an armv7 timer for zx297520v3
2026-04-21 20:23 ` [PATCH v5 5/8] ARM: dts: Add an armv7 timer for zx297520v3 Stefan Dösinger
@ 2026-04-22 7:10 ` Krzysztof Kozlowski
0 siblings, 0 replies; 14+ messages in thread
From: Krzysztof Kozlowski @ 2026-04-22 7:10 UTC (permalink / raw)
To: Stefan Dösinger
Cc: Jonathan Corbet, Shuah Khan, Russell King, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Arnd Bergmann,
Alexandre Belloni, Linus Walleij, Drew Fustini,
Greg Kroah-Hartman, Jiri Slaby, linux-doc, linux-kernel,
linux-arm-kernel, devicetree, soc, linux-serial
On Tue, Apr 21, 2026 at 11:23:13PM +0300, Stefan Dösinger wrote:
> The stock kernel does not use this timer, but it seems to work fine. The
> board has other board-specific timers that would need a driver and I see
> no reason to bother with them since the arm standard timer works.
>
> The caveat is the non-standard GIC setup needed to handle the timer's
> level-low PPI. This is the responsibility of the boot loader and
> documented in Documentation/arch/arm/zte/zx297520v3.rst.
>
> Signed-off-by: Stefan Dösinger <stefandoesinger@gmail.com>
> ---
> arch/arm/boot/dts/zte/zx297520v3.dtsi | 24 ++++++++++++++++++++++++
This must be squashed. You add new SoC - that's one commit. One logical
change. Adding "not working SoC" and then "let's fix it" are not two
separate tasks.
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH v5 6/8] amba/serial: amba-pl011: Bring back zx29 UART support
2026-04-21 20:23 [PATCH v5 0/8] Add support for ZTE zx297520v3 Stefan Dösinger
` (4 preceding siblings ...)
2026-04-21 20:23 ` [PATCH v5 5/8] ARM: dts: Add an armv7 timer for zx297520v3 Stefan Dösinger
@ 2026-04-21 20:23 ` Stefan Dösinger
2026-04-21 20:23 ` [PATCH v5 7/8] ARM: dts: Declare UARTs on zx297520v3 boards Stefan Dösinger
2026-04-21 20:23 ` [PATCH v5 8/8] ARM: defconfig: Add a zx29 defconfig file Stefan Dösinger
7 siblings, 0 replies; 14+ messages in thread
From: Stefan Dösinger @ 2026-04-21 20:23 UTC (permalink / raw)
To: Jonathan Corbet, Shuah Khan, Russell King, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Arnd Bergmann,
Krzysztof Kozlowski, Alexandre Belloni, Linus Walleij,
Drew Fustini, Greg Kroah-Hartman, Jiri Slaby
Cc: linux-doc, linux-kernel, linux-arm-kernel, devicetree, soc,
linux-serial, Stefan Dösinger
This is based on code removed in commit 89d4f98ae90d ("ARM: remove zte
zx platform"). I did not bring back the zx29-uart .compatible as the
arm,primecell-periphid does the job.
Signed-off-by: Stefan Dösinger <stefandoesinger@gmail.com>
---
Changes since v4:
Use ZTE's JEDEC ID instead of 0xfe for the DT-Provided AMBA ID.
---
drivers/tty/serial/amba-pl011.c | 42 +++++++++++++++++++++++++++++++++++++++++
1 file changed, 42 insertions(+)
diff --git a/drivers/tty/serial/amba-pl011.c b/drivers/tty/serial/amba-pl011.c
index 7f17d288c807..f24cc403d9e0 100644
--- a/drivers/tty/serial/amba-pl011.c
+++ b/drivers/tty/serial/amba-pl011.c
@@ -216,6 +216,38 @@ static struct vendor_data vendor_st = {
.get_fifosize = get_fifosize_st,
};
+static const u16 pl011_zte_offsets[REG_ARRAY_SIZE] = {
+ [REG_DR] = ZX_UART011_DR,
+ [REG_FR] = ZX_UART011_FR,
+ [REG_LCRH_RX] = ZX_UART011_LCRH,
+ [REG_LCRH_TX] = ZX_UART011_LCRH,
+ [REG_IBRD] = ZX_UART011_IBRD,
+ [REG_FBRD] = ZX_UART011_FBRD,
+ [REG_CR] = ZX_UART011_CR,
+ [REG_IFLS] = ZX_UART011_IFLS,
+ [REG_IMSC] = ZX_UART011_IMSC,
+ [REG_RIS] = ZX_UART011_RIS,
+ [REG_MIS] = ZX_UART011_MIS,
+ [REG_ICR] = ZX_UART011_ICR,
+ [REG_DMACR] = ZX_UART011_DMACR,
+};
+
+static unsigned int get_fifosize_zte(struct amba_device *dev)
+{
+ return 16;
+}
+
+static struct vendor_data vendor_zte = {
+ .reg_offset = pl011_zte_offsets,
+ .access_32b = true,
+ .ifls = UART011_IFLS_RX4_8 | UART011_IFLS_TX4_8,
+ .fr_busy = ZX_UART01x_FR_BUSY,
+ .fr_dsr = ZX_UART01x_FR_DSR,
+ .fr_cts = ZX_UART01x_FR_CTS,
+ .fr_ri = ZX_UART011_FR_RI,
+ .get_fifosize = get_fifosize_zte,
+};
+
/* Deals with DMA transactions */
struct pl011_dmabuf {
@@ -3081,6 +3113,16 @@ static const struct amba_id pl011_ids[] = {
.mask = 0x00ffffff,
.data = &vendor_st,
},
+ {
+ /* This is an invented ID. The actual hardware that contains
+ * these ZTE UARTs (zx29 boards) has no AMBA PIDs stored. ZTE
+ * JEDEC ID (ignoring banks) and the "011" part number as used
+ * by ARM.
+ */
+ .id = 0x0008c011,
+ .mask = 0x000fffff,
+ .data = &vendor_zte,
+ },
{ 0, 0 },
};
--
2.53.0
^ permalink raw reply related [flat|nested] 14+ messages in thread* [PATCH v5 7/8] ARM: dts: Declare UARTs on zx297520v3 boards
2026-04-21 20:23 [PATCH v5 0/8] Add support for ZTE zx297520v3 Stefan Dösinger
` (5 preceding siblings ...)
2026-04-21 20:23 ` [PATCH v5 6/8] amba/serial: amba-pl011: Bring back zx29 UART support Stefan Dösinger
@ 2026-04-21 20:23 ` Stefan Dösinger
2026-04-22 7:10 ` Krzysztof Kozlowski
2026-04-21 20:23 ` [PATCH v5 8/8] ARM: defconfig: Add a zx29 defconfig file Stefan Dösinger
7 siblings, 1 reply; 14+ messages in thread
From: Stefan Dösinger @ 2026-04-21 20:23 UTC (permalink / raw)
To: Jonathan Corbet, Shuah Khan, Russell King, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Arnd Bergmann,
Krzysztof Kozlowski, Alexandre Belloni, Linus Walleij,
Drew Fustini, Greg Kroah-Hartman, Jiri Slaby
Cc: linux-doc, linux-kernel, linux-arm-kernel, devicetree, soc,
linux-serial, Stefan Dösinger
Signed-off-by: Stefan Dösinger <stefandoesinger@gmail.com>
---
Changes since v4:
* Declare all uarts
* Remove the UART aliases for now. I can revisit this when I get my
hands on a board that exposes two UARTs.
---
arch/arm/boot/dts/zte/zx297520v3-dlink-dwr932m.dts | 4 +++
arch/arm/boot/dts/zte/zx297520v3.dtsi | 39 ++++++++++++++++++++++
2 files changed, 43 insertions(+)
diff --git a/arch/arm/boot/dts/zte/zx297520v3-dlink-dwr932m.dts b/arch/arm/boot/dts/zte/zx297520v3-dlink-dwr932m.dts
index ac20215fddef..1700f46aba86 100644
--- a/arch/arm/boot/dts/zte/zx297520v3-dlink-dwr932m.dts
+++ b/arch/arm/boot/dts/zte/zx297520v3-dlink-dwr932m.dts
@@ -16,3 +16,7 @@ memory@20000000 {
reg = <0x20000000 0x04000000>;
};
};
+
+&uart1 {
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/zte/zx297520v3.dtsi b/arch/arm/boot/dts/zte/zx297520v3.dtsi
index 903050c684cb..ca65797ed926 100644
--- a/arch/arm/boot/dts/zte/zx297520v3.dtsi
+++ b/arch/arm/boot/dts/zte/zx297520v3.dtsi
@@ -20,6 +20,15 @@ cpu@0 {
};
};
+ /* Base bus clock and default for the UART. It will be replaced once a clock driver has
+ * been added.
+ */
+ uartclk: uartclk: uartclk-26000000 {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <26000000>;
+ };
+
timer {
compatible = "arm,armv7-timer";
interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>,
@@ -60,5 +69,35 @@ gic: interrupt-controller@f2000000 {
reg = <0xf2000000 0x10000>,
<0xf2040000 0x20000>;
};
+
+ uart0: serial@131000 {
+ compatible = "arm,primecell";
+ arm,primecell-periphid = <0x0018c011>;
+ reg = <0x00131000 0x1000>;
+ interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&uartclk>, <&uartclk>;
+ clock-names = "uartclk", "apb_pclk";
+ status = "disabled";
+ };
+
+ uart1: serial@1408000 {
+ compatible = "arm,pl011", "arm,primecell";
+ arm,primecell-periphid = <0x0018c011>;
+ reg = <0x01408000 0x1000>;
+ interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&uartclk>, <&uartclk>;
+ clock-names = "uartclk", "apb_pclk";
+ status = "disabled";
+ };
+
+ uart2: serial@140d000 {
+ compatible = "arm,primecell";
+ arm,primecell-periphid = <0x0018c011>;
+ reg = <0x0140d000 0x1000>;
+ interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&uartclk>, <&uartclk>;
+ clock-names = "uartclk", "apb_pclk";
+ status = "disabled";
+ };
};
};
--
2.53.0
^ permalink raw reply related [flat|nested] 14+ messages in thread* Re: [PATCH v5 7/8] ARM: dts: Declare UARTs on zx297520v3 boards
2026-04-21 20:23 ` [PATCH v5 7/8] ARM: dts: Declare UARTs on zx297520v3 boards Stefan Dösinger
@ 2026-04-22 7:10 ` Krzysztof Kozlowski
2026-04-22 7:11 ` Krzysztof Kozlowski
0 siblings, 1 reply; 14+ messages in thread
From: Krzysztof Kozlowski @ 2026-04-22 7:10 UTC (permalink / raw)
To: Stefan Dösinger
Cc: Jonathan Corbet, Shuah Khan, Russell King, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Arnd Bergmann,
Alexandre Belloni, Linus Walleij, Drew Fustini,
Greg Kroah-Hartman, Jiri Slaby, linux-doc, linux-kernel,
linux-arm-kernel, devicetree, soc, linux-serial
On Tue, Apr 21, 2026 at 11:23:15PM +0300, Stefan Dösinger wrote:
> Signed-off-by: Stefan Dösinger <stefandoesinger@gmail.com>
>
> ---
>
Same comments about subject and squashing. This cannot be a separate
commit.
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH v5 7/8] ARM: dts: Declare UARTs on zx297520v3 boards
2026-04-22 7:10 ` Krzysztof Kozlowski
@ 2026-04-22 7:11 ` Krzysztof Kozlowski
0 siblings, 0 replies; 14+ messages in thread
From: Krzysztof Kozlowski @ 2026-04-22 7:11 UTC (permalink / raw)
To: Stefan Dösinger
Cc: Jonathan Corbet, Shuah Khan, Russell King, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Arnd Bergmann,
Alexandre Belloni, Linus Walleij, Drew Fustini,
Greg Kroah-Hartman, Jiri Slaby, linux-doc, linux-kernel,
linux-arm-kernel, devicetree, soc, linux-serial
On 22/04/2026 09:10, Krzysztof Kozlowski wrote:
> On Tue, Apr 21, 2026 at 11:23:15PM +0300, Stefan Dösinger wrote:
>> Signed-off-by: Stefan Dösinger <stefandoesinger@gmail.com>
>>
>> ---
>>
>
> Same comments about subject and squashing. This cannot be a separate
> commit.
>
Heh, and with empty commit msg!
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH v5 8/8] ARM: defconfig: Add a zx29 defconfig file
2026-04-21 20:23 [PATCH v5 0/8] Add support for ZTE zx297520v3 Stefan Dösinger
` (6 preceding siblings ...)
2026-04-21 20:23 ` [PATCH v5 7/8] ARM: dts: Declare UARTs on zx297520v3 boards Stefan Dösinger
@ 2026-04-21 20:23 ` Stefan Dösinger
7 siblings, 0 replies; 14+ messages in thread
From: Stefan Dösinger @ 2026-04-21 20:23 UTC (permalink / raw)
To: Jonathan Corbet, Shuah Khan, Russell King, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Arnd Bergmann,
Krzysztof Kozlowski, Alexandre Belloni, Linus Walleij,
Drew Fustini, Greg Kroah-Hartman, Jiri Slaby
Cc: linux-doc, linux-kernel, linux-arm-kernel, devicetree, soc,
linux-serial, Stefan Dösinger
This enables existing drivers that already are (UART) or will be (USB,
GPIO) necessary to operate this board even if they aren't declared in
the DTS yet.
Signed-off-by: Stefan Dösinger <stefandoesinger@gmail.com>
---
arch/arm/configs/zx29_defconfig | 89 +++++++++++++++++++++++++++++++++++++++++
1 file changed, 89 insertions(+)
diff --git a/arch/arm/configs/zx29_defconfig b/arch/arm/configs/zx29_defconfig
new file mode 100644
index 000000000000..a78decd1d525
--- /dev/null
+++ b/arch/arm/configs/zx29_defconfig
@@ -0,0 +1,89 @@
+CONFIG_SYSVIPC=y
+CONFIG_BLK_DEV_INITRD=y
+# CONFIG_RD_BZIP2 is not set
+# CONFIG_RD_LZMA is not set
+# CONFIG_RD_XZ is not set
+# CONFIG_RD_LZ4 is not set
+CONFIG_EXPERT=y
+CONFIG_KALLSYMS_ALL=y
+CONFIG_MMU=y
+CONFIG_ARCH_MULTI_V7=y
+CONFIG_ARCH_ZTE=y
+CONFIG_SOC_ZX297520V3=y
+# FIXME: There is no PSCI on this board, but ARM_GIC_V3 depends on it
+CONFIG_ARM_PSCI=y
+CONFIG_ARM_APPENDED_DTB=y
+CONFIG_CMDLINE="console=ttyAMA0 earlyprintk root=/dev/ram rw"
+# CONFIG_SUSPEND is not set
+CONFIG_BINFMT_FLAT=y
+# CONFIG_UEVENT_HELPER is not set
+# CONFIG_STANDALONE is not set
+# CONFIG_PREVENT_FIRMWARE_BUILD is not set
+# CONFIG_ALLOW_DEV_COREDUMP is not set
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=4
+CONFIG_CPU_FREQ=y
+CONFIG_CPUFREQ_DT_PLATDEV=y
+CONFIG_PM=y
+CONFIG_PM_CLK=y
+CONFIG_PM_GENERIC_DOMAINS=y
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_DEVTMPFS=y # FIXME: This is specific to my initrd. Remove before upstream
+CONFIG_DEVTMPFS_MOUNT=y
+# CONFIG_INPUT_MOUSEDEV is not set
+CONFIG_KEYBOARD_GPIO_POLLED=y
+CONFIG_GPIOLIB=y
+CONFIG_OF_GPIO=y
+CONFIG_GPIO_GENERIC_PLATFORM=y
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_SERIO is not set
+CONFIG_VT_HW_CONSOLE_BINDING=y
+CONFIG_SERIAL_AMBA_PL011=y
+CONFIG_SERIAL_AMBA_PL011_CONSOLE=y
+CONFIG_SERIAL_OF_PLATFORM=y
+CONFIG_SERIAL_DEV_BUS=y
+CONFIG_SERIAL_DEV_CTRL_TTYPORT=y
+# CONFIG_HW_RANDOM is not set
+CONFIG_MFD_SYSCON=y
+# CONFIG_HID is not set
+CONFIG_PINCTRL=y
+CONFIG_GENERIC_PINCTRL_GROUPS=y
+CONFIG_PINMUX=y
+CONFIG_GENERIC_PINMUX_FUNCTIONS=y
+CONFIG_PINCONF=y
+CONFIG_GENERIC_PINCONF=y
+CONFIG_RESET_CONTROLLER=y
+CONFIG_POWER_RESET=y
+CONFIG_RESET_SIMPLE=y
+CONFIG_LEDS_GPIO=y
+CONFIG_USB_DWC2=y
+CONFIG_USB_GADGET=y
+CONFIG_MTD=y
+CONFIG_MTD_OF_PARTS=y
+CONFIG_MTD_BLKDEVS=y
+CONFIG_MTD_BLOCK=y
+CONFIG_MTD_SPI_NAND=y
+CONFIG_SPI_MASTER=y
+CONFIG_MMC=y
+CONFIG_MMC_DW=y
+CONFIG_MMC_DW_PLTFM=y
+CONFIG_STMMAC_ETH=y
+CONFIG_STMMAC_PLATFORM=y
+CONFIG_MDIO_BUS=y
+CONFIG_REGULATOR=y
+CONFIG_REGULATOR_FIXED_VOLTAGE=y
+CONFIG_SRAM=y
+CONFIG_MISC_FILESYSTEMS=y
+CONFIG_JFFS2_FS=y
+CONFIG_CONFIG_TMPFS=y
+CONFIG_PRINTK_TIME=y
+CONFIG_EARLY_PRINTK=y
+CONFIG_DEBUG_LL=y
+CONFIG_DEBUG_ZTE_ZX=y
+CONFIG_DEBUG_LL_INCLUDE="debug/pl01x.S"
+CONFIG_DEBUG_UART_PL01X=y
+CONFIG_DEBUG_UART_PHYS=0x01408000
+CONFIG_DEBUG_UART_VIRT=0xf4708000
--
2.53.0
^ permalink raw reply related [flat|nested] 14+ messages in thread