FAILED: patch "[PATCH] usb: typec: fusb302: cache PD RX state" failed to apply to 5.15-stable tree

FAILED: patch "[PATCH] usb: typec: fusb302: cache PD RX state" failed to apply to 5.15-stable tree

[gregkh]

The patch below does not apply to the 5.15-stable tree.
If someone wants it applied there, or to any other stable or longterm
tree, then please email the backport, including the original git commit
id to <stable@vger.kernel.org>.

To reproduce the conflict and resubmit, you may use the following commands:

git fetch https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/ linux-5.15.y
git checkout FETCH_HEAD
git cherry-pick -x 1e61f6ab08786d66a11cfc51e13d6f08a6b06c56
# <resolve conflicts, build, test, etc.>
git commit -s
git send-email --to '<stable@vger.kernel.org>' --in-reply-to '2025081833-chatting-dragging-a84b@gregkh' --subject-prefix 'PATCH 5.15.y' HEAD^..

Possible dependencies:



thanks,

greg k-h

------------------ original commit in Linus's tree ------------------

From 1e61f6ab08786d66a11cfc51e13d6f08a6b06c56 Mon Sep 17 00:00:00 2001
From: Sebastian Reichel <sebastian.reichel@collabora.com>
Date: Fri, 4 Jul 2025 19:55:06 +0200
Subject: [PATCH] usb: typec: fusb302: cache PD RX state

This patch fixes a race condition communication error, which ends up in
PD hard resets when losing the race. Some systems, like the Radxa ROCK
5B are powered through USB-C without any backup power source and use a
FUSB302 chip to do the PD negotiation. This means it is quite important
to avoid hard resets, since that effectively kills the system's
power-supply.

I've found the following race condition while debugging unplanned power
loss during booting the board every now and then:

1. lots of TCPM/FUSB302/PD initialization stuff
2. TCPM ends up in SNK_WAIT_CAPABILITIES (tcpm_set_pd_rx is enabled here)
3. the remote PD source does not send anything, so TCPM does a SOFT RESET
4. TCPM ends up in SNK_WAIT_CAPABILITIES for the second time
   (tcpm_set_pd_rx is enabled again, even though it is still on)

At this point I've seen broken CRC good messages being send by the
FUSB302 with a logic analyzer sniffing the CC lines. Also it looks like
messages are being lost and things generally going haywire with one of
the two sides doing a hard reset once a broken CRC good message was send
to the bus.

I think the system is running into a race condition, that the FIFOs are
being cleared and/or the automatic good CRC message generation flag is
being updated while a message is already arriving.

Let's avoid this by caching the PD RX enabled state, as we have already
processed anything in the FIFOs and are in a good state. As a side
effect that this also optimizes I2C bus usage :)

As far as I can tell the problem theoretically also exists when TCPM
enters SNK_WAIT_CAPABILITIES the first time, but I believe this is less
critical for the following reason:

On devices like the ROCK 5B, which are powered through a TCPM backed
USB-C port, the bootloader must have done some prior PD communication
(initial communication must happen within 5 seconds after plugging the
USB-C plug). This means the first time the kernel TCPM state machine
reaches SNK_WAIT_CAPABILITIES, the remote side is not sending messages
actively. On other devices a hard reset simply adds some extra delay and
things should be good afterwards.

Fixes: c034a43e72dda ("staging: typec: Fairchild FUSB302 Type-c chip driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250704-fusb302-race-condition-fix-v1-1-239012c0e27a@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

diff --git a/drivers/usb/typec/tcpm/fusb302.c b/drivers/usb/typec/tcpm/fusb302.c
index f2801279c4b5..a4ff2403ddd6 100644
--- a/drivers/usb/typec/tcpm/fusb302.c
+++ b/drivers/usb/typec/tcpm/fusb302.c
@@ -104,6 +104,7 @@ struct fusb302_chip {
 	bool vconn_on;
 	bool vbus_on;
 	bool charge_on;
+	bool pd_rx_on;
 	bool vbus_present;
 	enum typec_cc_polarity cc_polarity;
 	enum typec_cc_status cc1;
@@ -841,6 +842,11 @@ static int tcpm_set_pd_rx(struct tcpc_dev *dev, bool on)
 	int ret = 0;
 
 	mutex_lock(&chip->lock);
+	if (chip->pd_rx_on == on) {
+		fusb302_log(chip, "pd is already %s", str_on_off(on));
+		goto done;
+	}
+
 	ret = fusb302_pd_rx_flush(chip);
 	if (ret < 0) {
 		fusb302_log(chip, "cannot flush pd rx buffer, ret=%d", ret);
@@ -863,6 +869,8 @@ static int tcpm_set_pd_rx(struct tcpc_dev *dev, bool on)
 			    str_on_off(on), ret);
 		goto done;
 	}
+
+	chip->pd_rx_on = on;
 	fusb302_log(chip, "pd := %s", str_on_off(on));
 done:
 	mutex_unlock(&chip->lock);

[PATCH 5.15.y] usb: typec: fusb302: cache PD RX state

[Sasha Levin]

From: Sebastian Reichel <sebastian.reichel@collabora.com>

[ Upstream commit 1e61f6ab08786d66a11cfc51e13d6f08a6b06c56 ]

This patch fixes a race condition communication error, which ends up in
PD hard resets when losing the race. Some systems, like the Radxa ROCK
5B are powered through USB-C without any backup power source and use a
FUSB302 chip to do the PD negotiation. This means it is quite important
to avoid hard resets, since that effectively kills the system's
power-supply.

I've found the following race condition while debugging unplanned power
loss during booting the board every now and then:

1. lots of TCPM/FUSB302/PD initialization stuff
2. TCPM ends up in SNK_WAIT_CAPABILITIES (tcpm_set_pd_rx is enabled here)
3. the remote PD source does not send anything, so TCPM does a SOFT RESET
4. TCPM ends up in SNK_WAIT_CAPABILITIES for the second time
   (tcpm_set_pd_rx is enabled again, even though it is still on)

At this point I've seen broken CRC good messages being send by the
FUSB302 with a logic analyzer sniffing the CC lines. Also it looks like
messages are being lost and things generally going haywire with one of
the two sides doing a hard reset once a broken CRC good message was send
to the bus.

I think the system is running into a race condition, that the FIFOs are
being cleared and/or the automatic good CRC message generation flag is
being updated while a message is already arriving.

Let's avoid this by caching the PD RX enabled state, as we have already
processed anything in the FIFOs and are in a good state. As a side
effect that this also optimizes I2C bus usage :)

As far as I can tell the problem theoretically also exists when TCPM
enters SNK_WAIT_CAPABILITIES the first time, but I believe this is less
critical for the following reason:

On devices like the ROCK 5B, which are powered through a TCPM backed
USB-C port, the bootloader must have done some prior PD communication
(initial communication must happen within 5 seconds after plugging the
USB-C plug). This means the first time the kernel TCPM state machine
reaches SNK_WAIT_CAPABILITIES, the remote side is not sending messages
actively. On other devices a hard reset simply adds some extra delay and
things should be good afterwards.

Fixes: c034a43e72dda ("staging: typec: Fairchild FUSB302 Type-c chip driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250704-fusb302-race-condition-fix-v1-1-239012c0e27a@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ replaced str_on_off(on) with ternary operator ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/usb/typec/tcpm/fusb302.c | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/drivers/usb/typec/tcpm/fusb302.c b/drivers/usb/typec/tcpm/fusb302.c
index 96c55eaf3f80..2ec67debc4ce 100644
--- a/drivers/usb/typec/tcpm/fusb302.c
+++ b/drivers/usb/typec/tcpm/fusb302.c
@@ -103,6 +103,7 @@ struct fusb302_chip {
 	bool vconn_on;
 	bool vbus_on;
 	bool charge_on;
+	bool pd_rx_on;
 	bool vbus_present;
 	enum typec_cc_polarity cc_polarity;
 	enum typec_cc_status cc1;
@@ -841,6 +842,11 @@ static int tcpm_set_pd_rx(struct tcpc_dev *dev, bool on)
 	int ret = 0;
 
 	mutex_lock(&chip->lock);
+	if (chip->pd_rx_on == on) {
+		fusb302_log(chip, "pd is already %s", on ? "on" : "off");
+		goto done;
+	}
+
 	ret = fusb302_pd_rx_flush(chip);
 	if (ret < 0) {
 		fusb302_log(chip, "cannot flush pd rx buffer, ret=%d", ret);
@@ -863,6 +869,8 @@ static int tcpm_set_pd_rx(struct tcpc_dev *dev, bool on)
 			    on ? "on" : "off", ret);
 		goto done;
 	}
+
+	chip->pd_rx_on = on;
 	fusb302_log(chip, "pd := %s", on ? "on" : "off");
 done:
 	mutex_unlock(&chip->lock);
-- 
2.50.1