FAILED: patch "[PATCH] phy: cadence: cdns-dphy: Update calibration wait time for" failed to apply to 6.17-stable tree

FAILED: patch "[PATCH] phy: cadence: cdns-dphy: Update calibration wait time for" failed to apply to 6.17-stable tree

[gregkh]

The patch below does not apply to the 6.17-stable tree.
If someone wants it applied there, or to any other stable or longterm
tree, then please email the backport, including the original git commit
id to <stable@vger.kernel.org>.

To reproduce the conflict and resubmit, you may use the following commands:

git fetch https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/ linux-6.17.y
git checkout FETCH_HEAD
git cherry-pick -x 2c27aaee934a1b5229152fe33a14f1fdf50da143
# <resolve conflicts, build, test, etc.>
git commit -s
git send-email --to '<stable@vger.kernel.org>' --in-reply-to '2025101625-laborer-imaging-a408@gregkh' --subject-prefix 'PATCH 6.17.y' HEAD^..

Possible dependencies:



thanks,

greg k-h

------------------ original commit in Linus's tree ------------------

From 2c27aaee934a1b5229152fe33a14f1fdf50da143 Mon Sep 17 00:00:00 2001
From: Devarsh Thakkar <devarsht@ti.com>
Date: Fri, 4 Jul 2025 18:29:15 +0530
Subject: [PATCH] phy: cadence: cdns-dphy: Update calibration wait time for
 startup state machine

Do read-modify-write so that we re-use the characterized reset value as
specified in TRM [1] to program calibration wait time which defines number
of cycles to wait for after startup state machine is in bandgap enable
state.

This fixes PLL lock timeout error faced while using RPi DSI Panel on TI's
AM62L and J721E SoC since earlier calibration wait time was getting
overwritten to zero value thus failing the PLL to lockup and causing
timeout.

[1] AM62P TRM (Section 14.8.6.3.2.1.1 DPHY_TX_DPHYTX_CMN0_CMN_DIG_TBIT2):
Link: https://www.ti.com/lit/pdf/spruj83

Cc: stable@vger.kernel.org
Fixes: 7a343c8bf4b5 ("phy: Add Cadence D-PHY support")
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Tested-by: Harikrishna Shenoy <h-shenoy@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://lore.kernel.org/r/20250704125915.1224738-3-devarsht@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>

diff --git a/drivers/phy/cadence/cdns-dphy.c b/drivers/phy/cadence/cdns-dphy.c
index da8de0a9d086..24a25606996c 100644
--- a/drivers/phy/cadence/cdns-dphy.c
+++ b/drivers/phy/cadence/cdns-dphy.c
@@ -30,6 +30,7 @@
 
 #define DPHY_CMN_SSM			DPHY_PMA_CMN(0x20)
 #define DPHY_CMN_SSM_EN			BIT(0)
+#define DPHY_CMN_SSM_CAL_WAIT_TIME	GENMASK(8, 1)
 #define DPHY_CMN_TX_MODE_EN		BIT(9)
 
 #define DPHY_CMN_PWM			DPHY_PMA_CMN(0x40)
@@ -410,7 +411,8 @@ static int cdns_dphy_power_on(struct phy *phy)
 	writel(reg, dphy->regs + DPHY_BAND_CFG);
 
 	/* Start TX state machine. */
-	writel(DPHY_CMN_SSM_EN | DPHY_CMN_TX_MODE_EN,
+	reg = readl(dphy->regs + DPHY_CMN_SSM);
+	writel((reg & DPHY_CMN_SSM_CAL_WAIT_TIME) | DPHY_CMN_SSM_EN | DPHY_CMN_TX_MODE_EN,
 	       dphy->regs + DPHY_CMN_SSM);
 
 	ret = cdns_dphy_wait_for_pll_lock(dphy);

[PATCH 6.17.y 1/3] phy: cdns-dphy: Store hs_clk_rate and return it

[Sasha Levin]

From: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>

[ Upstream commit 689a54acb56858c85de8c7285db82b8ae6dbf683 ]

The DPHY driver does not return the actual hs_clk_rate, so the DSI
driver has no idea what clock was actually achieved. Set the realized
hs_clk_rate to the opts struct, so that the DSI driver gets it back.

Reviewed-by: Aradhya Bhatia <aradhya.bhatia@linux.dev>
Tested-by: Parth Pancholi <parth.pancholi@toradex.com>
Tested-by: Jayesh Choudhary <j-choudhary@ti.com>
Acked-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://lore.kernel.org/r/20250723-cdns-dphy-hs-clk-rate-fix-v1-1-d4539d44cbe7@ideasonboard.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Stable-dep-of: 2c27aaee934a ("phy: cadence: cdns-dphy: Update calibration wait time for startup state machine")
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/phy/cadence/cdns-dphy.c | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/drivers/phy/cadence/cdns-dphy.c b/drivers/phy/cadence/cdns-dphy.c
index ed87a3970f834..f79ec4fab4093 100644
--- a/drivers/phy/cadence/cdns-dphy.c
+++ b/drivers/phy/cadence/cdns-dphy.c
@@ -79,6 +79,7 @@ struct cdns_dphy_cfg {
 	u8 pll_ipdiv;
 	u8 pll_opdiv;
 	u16 pll_fbdiv;
+	u32 hs_clk_rate;
 	unsigned int nlanes;
 };
 
@@ -154,6 +155,9 @@ static int cdns_dsi_get_dphy_pll_cfg(struct cdns_dphy *dphy,
 					  cfg->pll_ipdiv,
 					  pll_ref_hz);
 
+	cfg->hs_clk_rate = div_u64((u64)pll_ref_hz * cfg->pll_fbdiv,
+				   2 * cfg->pll_opdiv * cfg->pll_ipdiv);
+
 	return 0;
 }
 
@@ -297,6 +301,7 @@ static int cdns_dphy_config_from_opts(struct phy *phy,
 	if (ret)
 		return ret;
 
+	opts->hs_clk_rate = cfg->hs_clk_rate;
 	opts->wakeup = cdns_dphy_get_wakeup_time_ns(dphy) / 1000;
 
 	return 0;
-- 
2.51.0

[PATCH 6.17.y 2/3] phy: cadence: cdns-dphy: Fix PLL lock and O_CMN_READY polling

[Sasha Levin]

From: Devarsh Thakkar <devarsht@ti.com>

[ Upstream commit 284fb19a3ffb1083c3ad9c00d29749d09dddb99c ]

PLL lockup and O_CMN_READY assertion can only happen after common state
machine gets enabled by programming DPHY_CMN_SSM register, but driver was
polling them before the common state machine was enabled which is
incorrect.  This is as per the DPHY initialization sequence as mentioned in
J721E TRM [1] at section "12.7.2.4.1.2.1 Start-up Sequence Timing Diagram".
It shows O_CMN_READY polling at the end after common configuration pin
setup where the common configuration pin setup step enables state machine
as referenced in "Table 12-1533. Common Configuration-Related Setup
mentions state machine"

To fix this :
- Add new function callbacks for polling on PLL lock and O_CMN_READY
  assertion.
- As state machine and clocks get enabled in power_on callback only, move
  the clock related programming part from configure callback to power_on
callback and poll for the PLL lockup and O_CMN_READY assertion after state
machine gets enabled.
- The configure callback only saves the PLL configuration received from the
  client driver which will be applied later on in power_on callback.
- Add checks to ensure configure is called before power_on and state
  machine is in disabled state before power_on callback is called.
- Disable state machine in power_off so that client driver can re-configure
  the PLL by following up a power_off, configure, power_on sequence.

[1]: https://www.ti.com/lit/zip/spruil1

Cc: stable@vger.kernel.org
Fixes: 7a343c8bf4b5 ("phy: Add Cadence D-PHY support")
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Tested-by: Harikrishna Shenoy <h-shenoy@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://lore.kernel.org/r/20250704125915.1224738-2-devarsht@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Stable-dep-of: 2c27aaee934a ("phy: cadence: cdns-dphy: Update calibration wait time for startup state machine")
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/phy/cadence/cdns-dphy.c | 124 +++++++++++++++++++++++---------
 1 file changed, 92 insertions(+), 32 deletions(-)

diff --git a/drivers/phy/cadence/cdns-dphy.c b/drivers/phy/cadence/cdns-dphy.c
index f79ec4fab4093..ee498df14ddab 100644
--- a/drivers/phy/cadence/cdns-dphy.c
+++ b/drivers/phy/cadence/cdns-dphy.c
@@ -100,6 +100,8 @@ struct cdns_dphy_ops {
 	void (*set_pll_cfg)(struct cdns_dphy *dphy,
 			    const struct cdns_dphy_cfg *cfg);
 	unsigned long (*get_wakeup_time_ns)(struct cdns_dphy *dphy);
+	int (*wait_for_pll_lock)(struct cdns_dphy *dphy);
+	int (*wait_for_cmn_ready)(struct cdns_dphy *dphy);
 };
 
 struct cdns_dphy {
@@ -109,6 +111,8 @@ struct cdns_dphy {
 	struct clk *pll_ref_clk;
 	const struct cdns_dphy_ops *ops;
 	struct phy *phy;
+	bool is_configured;
+	bool is_powered;
 };
 
 /* Order of bands is important since the index is the band number. */
@@ -195,6 +199,16 @@ static unsigned long cdns_dphy_get_wakeup_time_ns(struct cdns_dphy *dphy)
 	return dphy->ops->get_wakeup_time_ns(dphy);
 }
 
+static int cdns_dphy_wait_for_pll_lock(struct cdns_dphy *dphy)
+{
+	return dphy->ops->wait_for_pll_lock ? dphy->ops->wait_for_pll_lock(dphy) : 0;
+}
+
+static int cdns_dphy_wait_for_cmn_ready(struct cdns_dphy *dphy)
+{
+	return  dphy->ops->wait_for_cmn_ready ? dphy->ops->wait_for_cmn_ready(dphy) : 0;
+}
+
 static unsigned long cdns_dphy_ref_get_wakeup_time_ns(struct cdns_dphy *dphy)
 {
 	/* Default wakeup time is 800 ns (in a simulated environment). */
@@ -236,7 +250,6 @@ static unsigned long cdns_dphy_j721e_get_wakeup_time_ns(struct cdns_dphy *dphy)
 static void cdns_dphy_j721e_set_pll_cfg(struct cdns_dphy *dphy,
 					const struct cdns_dphy_cfg *cfg)
 {
-	u32 status;
 
 	/*
 	 * set the PWM and PLL Byteclk divider settings to recommended values
@@ -253,13 +266,6 @@ static void cdns_dphy_j721e_set_pll_cfg(struct cdns_dphy *dphy,
 
 	writel(DPHY_TX_J721E_WIZ_LANE_RSTB,
 	       dphy->regs + DPHY_TX_J721E_WIZ_RST_CTRL);
-
-	readl_poll_timeout(dphy->regs + DPHY_TX_J721E_WIZ_PLL_CTRL, status,
-			   (status & DPHY_TX_WIZ_PLL_LOCK), 0, POLL_TIMEOUT_US);
-
-	readl_poll_timeout(dphy->regs + DPHY_TX_J721E_WIZ_STATUS, status,
-			   (status & DPHY_TX_WIZ_O_CMN_READY), 0,
-			   POLL_TIMEOUT_US);
 }
 
 static void cdns_dphy_j721e_set_psm_div(struct cdns_dphy *dphy, u8 div)
@@ -267,6 +273,23 @@ static void cdns_dphy_j721e_set_psm_div(struct cdns_dphy *dphy, u8 div)
 	writel(div, dphy->regs + DPHY_TX_J721E_WIZ_PSM_FREQ);
 }
 
+static int cdns_dphy_j721e_wait_for_pll_lock(struct cdns_dphy *dphy)
+{
+	u32 status;
+
+	return readl_poll_timeout(dphy->regs + DPHY_TX_J721E_WIZ_PLL_CTRL, status,
+			       status & DPHY_TX_WIZ_PLL_LOCK, 0, POLL_TIMEOUT_US);
+}
+
+static int cdns_dphy_j721e_wait_for_cmn_ready(struct cdns_dphy *dphy)
+{
+	u32 status;
+
+	return readl_poll_timeout(dphy->regs + DPHY_TX_J721E_WIZ_STATUS, status,
+			       status & DPHY_TX_WIZ_O_CMN_READY, 0,
+			       POLL_TIMEOUT_US);
+}
+
 /*
  * This is the reference implementation of DPHY hooks. Specific integration of
  * this IP may have to re-implement some of them depending on how they decided
@@ -282,6 +305,8 @@ static const struct cdns_dphy_ops j721e_dphy_ops = {
 	.get_wakeup_time_ns = cdns_dphy_j721e_get_wakeup_time_ns,
 	.set_pll_cfg = cdns_dphy_j721e_set_pll_cfg,
 	.set_psm_div = cdns_dphy_j721e_set_psm_div,
+	.wait_for_pll_lock = cdns_dphy_j721e_wait_for_pll_lock,
+	.wait_for_cmn_ready = cdns_dphy_j721e_wait_for_cmn_ready,
 };
 
 static int cdns_dphy_config_from_opts(struct phy *phy,
@@ -339,21 +364,36 @@ static int cdns_dphy_validate(struct phy *phy, enum phy_mode mode, int submode,
 static int cdns_dphy_configure(struct phy *phy, union phy_configure_opts *opts)
 {
 	struct cdns_dphy *dphy = phy_get_drvdata(phy);
-	struct cdns_dphy_cfg cfg = { 0 };
-	int ret, band_ctrl;
-	unsigned int reg;
+	int ret;
 
-	ret = cdns_dphy_config_from_opts(phy, &opts->mipi_dphy, &cfg);
-	if (ret)
-		return ret;
+	ret = cdns_dphy_config_from_opts(phy, &opts->mipi_dphy, &dphy->cfg);
+	if (!ret)
+		dphy->is_configured = true;
+
+	return ret;
+}
+
+static int cdns_dphy_power_on(struct phy *phy)
+{
+	struct cdns_dphy *dphy = phy_get_drvdata(phy);
+	int ret;
+	u32 reg;
+
+	if (!dphy->is_configured || dphy->is_powered)
+		return -EINVAL;
+
+	clk_prepare_enable(dphy->psm_clk);
+	clk_prepare_enable(dphy->pll_ref_clk);
 
 	/*
 	 * Configure the internal PSM clk divider so that the DPHY has a
 	 * 1MHz clk (or something close).
 	 */
 	ret = cdns_dphy_setup_psm(dphy);
-	if (ret)
-		return ret;
+	if (ret) {
+		dev_err(&dphy->phy->dev, "Failed to setup PSM with error %d\n", ret);
+		goto err_power_on;
+	}
 
 	/*
 	 * Configure attach clk lanes to data lanes: the DPHY has 2 clk lanes
@@ -368,40 +408,60 @@ static int cdns_dphy_configure(struct phy *phy, union phy_configure_opts *opts)
 	 * Configure the DPHY PLL that will be used to generate the TX byte
 	 * clk.
 	 */
-	cdns_dphy_set_pll_cfg(dphy, &cfg);
+	cdns_dphy_set_pll_cfg(dphy, &dphy->cfg);
 
-	band_ctrl = cdns_dphy_tx_get_band_ctrl(opts->mipi_dphy.hs_clk_rate);
-	if (band_ctrl < 0)
-		return band_ctrl;
+	ret = cdns_dphy_tx_get_band_ctrl(dphy->cfg.hs_clk_rate);
+	if (ret < 0) {
+		dev_err(&dphy->phy->dev, "Failed to get band control value with error %d\n", ret);
+		goto err_power_on;
+	}
 
-	reg = FIELD_PREP(DPHY_BAND_CFG_LEFT_BAND, band_ctrl) |
-	      FIELD_PREP(DPHY_BAND_CFG_RIGHT_BAND, band_ctrl);
+	reg = FIELD_PREP(DPHY_BAND_CFG_LEFT_BAND, ret) |
+	      FIELD_PREP(DPHY_BAND_CFG_RIGHT_BAND, ret);
 	writel(reg, dphy->regs + DPHY_BAND_CFG);
 
-	return 0;
-}
-
-static int cdns_dphy_power_on(struct phy *phy)
-{
-	struct cdns_dphy *dphy = phy_get_drvdata(phy);
-
-	clk_prepare_enable(dphy->psm_clk);
-	clk_prepare_enable(dphy->pll_ref_clk);
-
 	/* Start TX state machine. */
 	writel(DPHY_CMN_SSM_EN | DPHY_CMN_TX_MODE_EN,
 	       dphy->regs + DPHY_CMN_SSM);
 
+	ret = cdns_dphy_wait_for_pll_lock(dphy);
+	if (ret) {
+		dev_err(&dphy->phy->dev, "Failed to lock PLL with error %d\n", ret);
+		goto err_power_on;
+	}
+
+	ret = cdns_dphy_wait_for_cmn_ready(dphy);
+	if (ret) {
+		dev_err(&dphy->phy->dev, "O_CMN_READY signal failed to assert with error %d\n",
+			ret);
+		goto err_power_on;
+	}
+
+	dphy->is_powered = true;
+
 	return 0;
+
+err_power_on:
+	clk_disable_unprepare(dphy->pll_ref_clk);
+	clk_disable_unprepare(dphy->psm_clk);
+
+	return ret;
 }
 
 static int cdns_dphy_power_off(struct phy *phy)
 {
 	struct cdns_dphy *dphy = phy_get_drvdata(phy);
+	u32 reg;
 
 	clk_disable_unprepare(dphy->pll_ref_clk);
 	clk_disable_unprepare(dphy->psm_clk);
 
+	/* Stop TX state machine. */
+	reg = readl(dphy->regs + DPHY_CMN_SSM);
+	writel(reg & ~DPHY_CMN_SSM_EN, dphy->regs + DPHY_CMN_SSM);
+
+	dphy->is_powered = false;
+
 	return 0;
 }
 
-- 
2.51.0

[PATCH 6.17.y 3/3] phy: cadence: cdns-dphy: Update calibration wait time for startup state machine

[Sasha Levin]

From: Devarsh Thakkar <devarsht@ti.com>

[ Upstream commit 2c27aaee934a1b5229152fe33a14f1fdf50da143 ]

Do read-modify-write so that we re-use the characterized reset value as
specified in TRM [1] to program calibration wait time which defines number
of cycles to wait for after startup state machine is in bandgap enable
state.

This fixes PLL lock timeout error faced while using RPi DSI Panel on TI's
AM62L and J721E SoC since earlier calibration wait time was getting
overwritten to zero value thus failing the PLL to lockup and causing
timeout.

[1] AM62P TRM (Section 14.8.6.3.2.1.1 DPHY_TX_DPHYTX_CMN0_CMN_DIG_TBIT2):
Link: https://www.ti.com/lit/pdf/spruj83

Cc: stable@vger.kernel.org
Fixes: 7a343c8bf4b5 ("phy: Add Cadence D-PHY support")
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Tested-by: Harikrishna Shenoy <h-shenoy@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://lore.kernel.org/r/20250704125915.1224738-3-devarsht@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/phy/cadence/cdns-dphy.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/drivers/phy/cadence/cdns-dphy.c b/drivers/phy/cadence/cdns-dphy.c
index ee498df14ddab..de5389374d79d 100644
--- a/drivers/phy/cadence/cdns-dphy.c
+++ b/drivers/phy/cadence/cdns-dphy.c
@@ -30,6 +30,7 @@
 
 #define DPHY_CMN_SSM			DPHY_PMA_CMN(0x20)
 #define DPHY_CMN_SSM_EN			BIT(0)
+#define DPHY_CMN_SSM_CAL_WAIT_TIME	GENMASK(8, 1)
 #define DPHY_CMN_TX_MODE_EN		BIT(9)
 
 #define DPHY_CMN_PWM			DPHY_PMA_CMN(0x40)
@@ -421,7 +422,8 @@ static int cdns_dphy_power_on(struct phy *phy)
 	writel(reg, dphy->regs + DPHY_BAND_CFG);
 
 	/* Start TX state machine. */
-	writel(DPHY_CMN_SSM_EN | DPHY_CMN_TX_MODE_EN,
+	reg = readl(dphy->regs + DPHY_CMN_SSM);
+	writel((reg & DPHY_CMN_SSM_CAL_WAIT_TIME) | DPHY_CMN_SSM_EN | DPHY_CMN_TX_MODE_EN,
 	       dphy->regs + DPHY_CMN_SSM);
 
 	ret = cdns_dphy_wait_for_pll_lock(dphy);
-- 
2.51.0