* [U-Boot] [PATCH 2/2] sunxi: Add defconfig and dts for colorfly e708 q1 tablet
2016-03-09 21:51 [U-Boot] [PATCH 1/2] sunxi: A23: Fix some revisions needing a different magic sram poke Hans de Goede
@ 2016-03-09 21:51 ` Hans de Goede
2016-03-11 10:13 ` [U-Boot] [PATCH 1/2] sunxi: A23: Fix some revisions needing a different magic sram poke Ian Campbell
1 sibling, 0 replies; 3+ messages in thread
From: Hans de Goede @ 2016-03-09 21:51 UTC (permalink / raw)
To: u-boot
The colorfly e708 q1 is a 7" tablet which is clearly marked as colorfly
e708 q1 on the back. It features a 9:16 800x1280 IPS LCD, A31s SoC,
1GB RAM, 8G NAND, ilitek 2139qt004 touchscreen on i2c-1 addr 0x41,
stk8313 accelerometer on i2c-2 addr 0x22 and a rtl8188etv wifi chip.
The added dts is identical to the dts submitted to the upstream kernel,
note this commit also syncs axp22x.dtsi and sun6i-a31.dtsi with the
upstream kernel as the added dts depends on these.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
---
arch/arm/dts/Makefile | 1 +
arch/arm/dts/axp22x.dtsi | 143 ++++++++++++++++++
arch/arm/dts/sun6i-a31.dtsi | 65 ++++++++-
arch/arm/dts/sun6i-a31s-colorfly-e708-q1.dts | 208 +++++++++++++++++++++++++++
board/sunxi/MAINTAINERS | 1 +
configs/colorfly_e708_q1_defconfig | 25 ++++
6 files changed, 440 insertions(+), 3 deletions(-)
create mode 100644 arch/arm/dts/axp22x.dtsi
create mode 100644 arch/arm/dts/sun6i-a31s-colorfly-e708-q1.dts
create mode 100644 configs/colorfly_e708_q1_defconfig
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 578038b..a8bc7b0 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -152,6 +152,7 @@ dtb-$(CONFIG_MACH_SUN6I) += \
sun6i-a31-m9.dtb \
sun6i-a31-mele-a1000g-quad.dtb \
sun6i-a31-mixtile-loftq.dtb \
+ sun6i-a31s-colorfly-e708-q1.dtb \
sun6i-a31s-cs908.dtb \
sun6i-a31s-primo81.dtb \
sun6i-a31s-sinovoip-bpi-m2.dtb
diff --git a/arch/arm/dts/axp22x.dtsi b/arch/arm/dts/axp22x.dtsi
new file mode 100644
index 0000000..76302f5
--- /dev/null
+++ b/arch/arm/dts/axp22x.dtsi
@@ -0,0 +1,143 @@
+/*
+ * Copyright 2015 Chen-Yu Tsai
+ *
+ * Chen-Yu Tsai <wens@csie.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/*
+ * AXP221/221s/223 Integrated Power Management Chip
+ * http://www.x-powers.com/product/AXP22X.php
+ * http://dl.linux-sunxi.org/AXP/AXP221%20Datasheet%20V1.2%2020130326%20.pdf
+ */
+
+&axp22x {
+ interrupt-controller;
+ #interrupt-cells = <1>;
+
+ regulators {
+ /* Default work frequency for buck regulators */
+ x-powers,dcdc-freq = <3000>;
+
+ reg_dcdc1: dcdc1 {
+ regulator-name = "dcdc1";
+ };
+
+ reg_dcdc2: dcdc2 {
+ regulator-name = "dcdc2";
+ };
+
+ reg_dcdc3: dcdc3 {
+ regulator-name = "dcdc3";
+ };
+
+ reg_dcdc4: dcdc4 {
+ regulator-name = "dcdc4";
+ };
+
+ reg_dcdc5: dcdc5 {
+ regulator-name = "dcdc5";
+ };
+
+ reg_dc1sw: dc1sw {
+ regulator-name = "dc1sw";
+ };
+
+ reg_dc5ldo: dc5ldo {
+ regulator-name = "dc5ldo";
+ };
+
+ reg_aldo1: aldo1 {
+ regulator-name = "aldo1";
+ };
+
+ reg_aldo2: aldo2 {
+ regulator-name = "aldo2";
+ };
+
+ reg_aldo3: aldo3 {
+ regulator-name = "aldo3";
+ };
+
+ reg_dldo1: dldo1 {
+ regulator-name = "dldo1";
+ };
+
+ reg_dldo2: dldo2 {
+ regulator-name = "dldo2";
+ };
+
+ reg_dldo3: dldo3 {
+ regulator-name = "dldo3";
+ };
+
+ reg_dldo4: dldo4 {
+ regulator-name = "dldo4";
+ };
+
+ reg_eldo1: eldo1 {
+ regulator-name = "eldo1";
+ };
+
+ reg_eldo2: eldo2 {
+ regulator-name = "eldo2";
+ };
+
+ reg_eldo3: eldo3 {
+ regulator-name = "eldo3";
+ };
+
+ reg_ldo_io0: ldo_io0 {
+ regulator-name = "ldo_io0";
+ };
+
+ reg_ldo_io1: ldo_io1 {
+ regulator-name = "ldo_io1";
+ };
+
+ reg_rtc_ldo: rtc_ldo {
+ /* RTC_LDO is a fixed, always-on regulator */
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "rtc_ldo";
+ };
+ };
+};
diff --git a/arch/arm/dts/sun6i-a31.dtsi b/arch/arm/dts/sun6i-a31.dtsi
index 44f889f..1867af2 100644
--- a/arch/arm/dts/sun6i-a31.dtsi
+++ b/arch/arm/dts/sun6i-a31.dtsi
@@ -61,7 +61,7 @@
#size-cells = <1>;
ranges;
- framebuffer at 0 {
+ simplefb_hdmi: framebuffer at 0 {
compatible = "allwinner,simple-framebuffer",
"simple-framebuffer";
allwinner,pipeline = "de_be0-lcd0-hdmi";
@@ -69,7 +69,7 @@
status = "disabled";
};
- framebuffer at 1 {
+ simplefb_lcd: framebuffer at 1 {
compatible = "allwinner,simple-framebuffer",
"simple-framebuffer";
allwinner,pipeline = "de_be0-lcd0";
@@ -252,6 +252,20 @@
compatible = "allwinner,sun6i-a31-ahb1-gates-clk";
reg = <0x01c20060 0x8>;
clocks = <&ahb1>;
+ clock-indices = <1>, <5>,
+ <6>, <8>, <9>,
+ <10>, <11>, <12>,
+ <13>, <14>,
+ <17>, <18>, <19>,
+ <20>, <21>, <22>,
+ <23>, <24>, <26>,
+ <27>, <29>,
+ <30>, <31>, <32>,
+ <36>, <37>, <40>,
+ <43>, <44>, <45>,
+ <46>, <47>, <50>,
+ <52>, <55>, <56>,
+ <57>, <58>;
clock-output-names = "ahb1_mipidsi", "ahb1_ss",
"ahb1_dma", "ahb1_mmc0", "ahb1_mmc1",
"ahb1_mmc2", "ahb1_mmc3", "ahb1_nand1",
@@ -281,6 +295,9 @@
compatible = "allwinner,sun6i-a31-apb1-gates-clk";
reg = <0x01c20068 0x4>;
clocks = <&apb1>;
+ clock-indices = <0>, <4>,
+ <5>, <12>,
+ <13>;
clock-output-names = "apb1_codec", "apb1_digital_mic",
"apb1_pio", "apb1_daudio0",
"apb1_daudio1";
@@ -299,6 +316,10 @@
compatible = "allwinner,sun6i-a31-apb2-gates-clk";
reg = <0x01c2006c 0x4>;
clocks = <&apb2>;
+ clock-indices = <0>, <1>,
+ <2>, <3>, <16>,
+ <17>, <18>, <19>,
+ <20>, <21>;
clock-output-names = "apb2_i2c0", "apb2_i2c1",
"apb2_i2c2", "apb2_i2c3",
"apb2_uart0", "apb2_uart1",
@@ -346,6 +367,14 @@
"mmc3_sample";
};
+ ss_clk: clk at 01c2009c {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-mod0-clk";
+ reg = <0x01c2009c 0x4>;
+ clocks = <&osc24M>, <&pll6 0>;
+ clock-output-names = "ss";
+ };
+
spi0_clk: clk at 01c200a0 {
#clock-cells = <0>;
compatible = "allwinner,sun4i-a10-mod0-clk";
@@ -384,6 +413,9 @@
compatible = "allwinner,sun6i-a31-usb-clk";
reg = <0x01c200cc 0x4>;
clocks = <&osc24M>;
+ clock-indices = <8>, <9>, <10>,
+ <16>, <17>,
+ <18>;
clock-output-names = "usb_phy0", "usb_phy1", "usb_phy2",
"usb_ohci0", "usb_ohci1",
"usb_ohci2";
@@ -677,6 +709,16 @@
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
+ mmc3_8bit_emmc_pins: mmc3 at 1 {
+ allwinner,pins = "PC6", "PC7", "PC8", "PC9",
+ "PC10", "PC11", "PC12",
+ "PC13", "PC14", "PC15",
+ "PC24";
+ allwinner,function = "mmc3";
+ allwinner,drive = <SUN4I_PINCTRL_40_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
gmac_pins_mii_a: gmac_mii at 0 {
allwinner,pins = "PA0", "PA1", "PA2", "PA3",
"PA8", "PA9", "PA11",
@@ -754,6 +796,13 @@
reg = <0x01c20ca0 0x20>;
};
+ lradc: lradc at 01c22800 {
+ compatible = "allwinner,sun4i-a10-lradc-keys";
+ reg = <0x01c22800 0x100>;
+ interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
rtp: rtp at 01c25000 {
compatible = "allwinner,sun6i-a31-ts";
reg = <0x01c25000 0x100>;
@@ -900,6 +949,16 @@
#size-cells = <0>;
};
+ crypto: crypto-engine at 01c15000 {
+ compatible = "allwinner,sun4i-a10-crypto";
+ reg = <0x01c15000 0x1000>;
+ interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ahb1_gates 5>, <&ss_clk>;
+ clock-names = "ahb", "mod";
+ resets = <&ahb1_rst 5>;
+ reset-names = "ahb";
+ };
+
timer at 01c60000 {
compatible = "allwinner,sun6i-a31-hstimer",
"allwinner,sun7i-a20-hstimer";
@@ -1061,7 +1120,7 @@
resets = <&apb0_rst 0>;
gpio-controller;
interrupt-controller;
- #interrupt-cells = <2>;
+ #interrupt-cells = <3>;
#size-cells = <0>;
#gpio-cells = <3>;
diff --git a/arch/arm/dts/sun6i-a31s-colorfly-e708-q1.dts b/arch/arm/dts/sun6i-a31s-colorfly-e708-q1.dts
new file mode 100644
index 0000000..e182eec
--- /dev/null
+++ b/arch/arm/dts/sun6i-a31s-colorfly-e708-q1.dts
@@ -0,0 +1,208 @@
+/*
+ * Copyright 2016 Hans de Goede <hdegoede@redhat.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun6i-a31s.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "Colorfly E708 Q1 tablet";
+ compatible = "colorfly,e708-q1", "allwinner,sun6i-a31s";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&cpu0 {
+ cpu-supply = <®_dcdc3>;
+};
+
+&ehci0 {
+ /* rtl8188etv wifi is connected here */
+ status = "okay";
+};
+
+&lradc {
+ vref-supply = <®_aldo3>;
+ status = "okay";
+
+ button at 1000 {
+ label = "Home";
+ linux,code = <KEY_HOMEPAGE>;
+ channel = <0>;
+ voltage = <1000000>;
+ };
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_e708_q1>;
+ vmmc-supply = <®_dcdc1>;
+ bus-width = <4>;
+ cd-gpios = <&pio 0 8 GPIO_ACTIVE_HIGH>; /* PA8 */
+ cd-inverted;
+ status = "okay";
+};
+
+&pio {
+ mma8452_int_e708_q1: mma8452_int_pin at 0 {
+ allwinner,pins = "PA9";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
+ mmc0_cd_pin_e708_q1: mmc0_cd_pin at 0 {
+ allwinner,pins = "PA8";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+};
+
+&p2wi {
+ status = "okay";
+
+ axp22x: pmic at 68 {
+ compatible = "x-powers,axp221";
+ reg = <0x68>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+#include "axp22x.dtsi"
+
+®_aldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "avcc";
+};
+
+®_dc1sw {
+ regulator-name = "vcc-lcd";
+};
+
+®_dc5ldo {
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd-cpus"; /* This is an educated guess */
+};
+
+®_dcdc1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-3v0";
+};
+
+®_dcdc2 {
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd-gpu";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc4 {
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd-sys-dll";
+};
+
+®_dcdc5 {
+ regulator-always-on;
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vcc-dram";
+};
+
+®_dldo1 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi";
+};
+
+®_dldo2 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc-pg";
+};
+
+&simplefb_lcd {
+ vcc-lcd-supply = <®_dc1sw>;
+ vcc-pg-supply = <®_dldo2>;
+};
+
+/*
+ * FIXME for now we only support host mode and rely on u-boot to have
+ * turned on Vbus which is controlled by the axp221 pmic on the board.
+ *
+ * Once we have axp221 power-supply and vbus-usb support we should switch
+ * to fully supporting otg.
+ */
+&usb_otg {
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_dldo1>;
+ status = "okay";
+};
diff --git a/board/sunxi/MAINTAINERS b/board/sunxi/MAINTAINERS
index 739b6fd..34729d2 100644
--- a/board/sunxi/MAINTAINERS
+++ b/board/sunxi/MAINTAINERS
@@ -33,6 +33,7 @@ F: configs/r7-tv-dongle_defconfig
F: configs/UTOO_P66_defconfig
F: configs/Wobo_i5_defconfig
F: include/configs/sun6i.h
+F: configs/colorfly_e708_q1_defconfig
F: configs/CSQ_CS908_defconfig
F: configs/Mele_A1000G_quad_defconfig
F: configs/Mele_M9_defconfig
diff --git a/configs/colorfly_e708_q1_defconfig b/configs/colorfly_e708_q1_defconfig
new file mode 100644
index 0000000..5958d334
--- /dev/null
+++ b/configs/colorfly_e708_q1_defconfig
@@ -0,0 +1,25 @@
+CONFIG_ARM=y
+CONFIG_ARCH_SUNXI=y
+CONFIG_MACH_SUN6I=y
+CONFIG_DRAM_CLK=432
+CONFIG_DRAM_ZQ=251
+CONFIG_MMC0_CD_PIN="PA8"
+CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
+CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
+CONFIG_USB0_ID_DET="PA15"
+CONFIG_AXP_GPIO=y
+CONFIG_VIDEO_LCD_MODE="x:800,y:1280,depth:24,pclk_khz:64000,le:20,ri:34,up:1,lo:16,hs:10,vs:1,sync:3,vmode:0"
+CONFIG_VIDEO_LCD_DCLK_PHASE=0
+CONFIG_VIDEO_LCD_BL_EN="PA25"
+CONFIG_VIDEO_LCD_BL_PWM="PH13"
+CONFIG_VIDEO_LCD_PANEL_LVDS=y
+CONFIG_DEFAULT_DEVICE_TREE="sun6i-a31s-colorfly-e708-q1"
+# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_SPL=y
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_FLASH is not set
+# CONFIG_CMD_FPGA is not set
+CONFIG_CMD_GPIO=y
+CONFIG_AXP_DLDO1_VOLT=3300
+CONFIG_AXP_DLDO2_VOLT=1800
+CONFIG_USB_MUSB_HOST=y
--
2.7.2
^ permalink raw reply related [flat|nested] 3+ messages in thread