U-Boot Archive on lore.kernel.org
 help / color / mirror / Atom feed
From: Wenyou Yang <wenyou.yang@atmel.com>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH v2 3/4] board: sama5d2_xplained: Set 'ethaddr' got from AT24MAC
Date: Tue, 13 Sep 2016 10:49:04 +0800	[thread overview]
Message-ID: <1473734945-23975-4-git-send-email-wenyou.yang@atmel.com> (raw)
In-Reply-To: <1473734945-23975-1-git-send-email-wenyou.yang@atmel.com>

If 'ethaddr' is not set, we will get the ethernet address from AT24MAC,
and set it to 'ethaddr' variable.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Songjun Wu <songjun.wu@microchip.com>
---

Changes in v2: None

 board/atmel/sama5d2_xplained/sama5d2_xplained.c | 51 +++++++++++++++++++++++++
 include/configs/sama5d2_xplained.h              |  6 +++
 2 files changed, 57 insertions(+)

diff --git a/board/atmel/sama5d2_xplained/sama5d2_xplained.c b/board/atmel/sama5d2_xplained/sama5d2_xplained.c
index 7ccadf2..c94574b 100644
--- a/board/atmel/sama5d2_xplained/sama5d2_xplained.c
+++ b/board/atmel/sama5d2_xplained/sama5d2_xplained.c
@@ -7,6 +7,8 @@
 
 #include <common.h>
 #include <atmel_hlcdc.h>
+#include <dm.h>
+#include <i2c.h>
 #include <lcd.h>
 #include <mmc.h>
 #include <net.h>
@@ -192,6 +194,55 @@ int board_eth_init(bd_t *bis)
 	return rc;
 }
 
+#ifdef CONFIG_CMD_I2C
+static int set_ethaddr_from_eeprom(void)
+{
+	const int ETH_ADDR_LEN = 6;
+	unsigned char ethaddr[ETH_ADDR_LEN];
+	const char *ETHADDR_NAME = "ethaddr";
+	struct udevice *bus, *dev;
+
+	if (getenv(ETHADDR_NAME))
+		return 0;
+
+	if (uclass_get_device_by_seq(UCLASS_I2C, 1, &bus)) {
+		printf("Cannot find I2C bus 1\n");
+		return -1;
+	}
+
+	if (dm_i2c_probe(bus, CONFIG_AT24MAC_ADDR, 0, &dev)) {
+		printf("Failed to probe I2C chip\n");
+		return -1;
+	}
+
+	if (dm_i2c_read(dev, CONFIG_AT24MAC_REG, ethaddr, ETH_ADDR_LEN)) {
+		printf("Failed to read ethernet address from EEPROM\n");
+		return -1;
+	}
+
+	if (!is_valid_ethaddr(ethaddr)) {
+		printf("The ethernet address read from EEPROM is not valid!\n");
+		return -1;
+	}
+
+	return eth_setenv_enetaddr(ETHADDR_NAME, ethaddr);
+}
+#else
+static int set_ethaddr_from_eeprom(void)
+{
+	return 0;
+}
+#endif
+
+#ifdef CONFIG_MISC_INIT_R
+int misc_init_r(void)
+{
+	set_ethaddr_from_eeprom();
+
+	return 0;
+}
+#endif
+
 /* SPL */
 #ifdef CONFIG_SPL_BUILD
 void spl_board_init(void)
diff --git a/include/configs/sama5d2_xplained.h b/include/configs/sama5d2_xplained.h
index 77757a3..cada04f 100644
--- a/include/configs/sama5d2_xplained.h
+++ b/include/configs/sama5d2_xplained.h
@@ -15,6 +15,8 @@
 
 #include "at91-sama5_common.h"
 
+#define CONFIG_MISC_INIT_R
+
 /* SDRAM */
 #define CONFIG_NR_DRAM_BANKS		1
 #define CONFIG_SYS_SDRAM_BASE           ATMEL_BASE_DDRCS
@@ -54,6 +56,10 @@
 #define CONFIG_DOS_PARTITION
 #endif
 
+/* I2C */
+#define CONFIG_AT24MAC_ADDR		0x5c
+#define CONFIG_AT24MAC_REG		0x9a
+
 /* Ethernet Hardware */
 #define CONFIG_MACB
 #define CONFIG_RMII
-- 
2.7.4

  parent reply	other threads:[~2016-09-13  2:49 UTC|newest]

Thread overview: 11+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2016-09-13  2:49 [U-Boot] [PATCH v2 0/4] board: sama5d2_xplained: Convert to use device tree and drivers with DM Wenyou Yang
2016-09-13  2:49 ` [U-Boot] [PATCH v2 1/4] board: sama5d2_xplained: Move config options to defconfigs Wenyou Yang
2016-10-16 20:11   ` [U-Boot] [U-Boot, v2, " Andreas Bießmann
2016-09-13  2:49 ` [U-Boot] [PATCH v2 2/4] board: sama5d2_xplained: Clean up code Wenyou Yang
2016-10-16 20:17   ` [U-Boot] [U-Boot, v2, " Andreas Bießmann
2016-09-13  2:49 ` Wenyou Yang [this message]
2016-10-16 20:18   ` [U-Boot] [U-Boot, v2, 3/4] board: sama5d2_xplained: Set 'ethaddr' got from AT24MAC Andreas Bießmann
2016-10-16 21:42   ` Andreas Bießmann
2016-10-16 22:03     ` Tom Rini
2016-09-13  2:49 ` [U-Boot] [PATCH v2 4/4] board: sama5d2_xplained: Enable an early debug UART Wenyou Yang
2016-10-16 20:20   ` [U-Boot] [U-Boot, v2, " Andreas Bießmann

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1473734945-23975-4-git-send-email-wenyou.yang@atmel.com \
    --to=wenyou.yang@atmel.com \
    --cc=u-boot@lists.denx.de \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox