* [U-Boot] [PATCH v5 1/4] mmc: sunxi: add support for automatic delay calibration
2018-11-06 4:24 [U-Boot] [PATCH v5 0/4] Add support for Pinebook Vasily Khoruzhick
@ 2018-11-06 4:24 ` Vasily Khoruzhick
2018-11-06 4:24 ` [U-Boot] [PATCH v5 2/4] dm: video: bridge: don't fail to activate bridge if reset or sleep GPIO is missing Vasily Khoruzhick
` (3 subsequent siblings)
4 siblings, 0 replies; 6+ messages in thread
From: Vasily Khoruzhick @ 2018-11-06 4:24 UTC (permalink / raw)
To: u-boot
A64 and H6 support automatic delay calibration and Linux driver uses it
instead of hardcoded delays. Add support for it to u-boot driver.
Fixes eMMC instability on Pinebook
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Cc: Vagrant Cascadian <vagrant@debian.org>
---
arch/arm/include/asm/arch-sunxi/mmc.h | 6 +++++-
drivers/mmc/sunxi_mmc.c | 21 ++++++++++++++++++++-
2 files changed, 25 insertions(+), 2 deletions(-)
diff --git a/arch/arm/include/asm/arch-sunxi/mmc.h b/arch/arm/include/asm/arch-sunxi/mmc.h
index d98c53faaa..f2deafddd2 100644
--- a/arch/arm/include/asm/arch-sunxi/mmc.h
+++ b/arch/arm/include/asm/arch-sunxi/mmc.h
@@ -46,7 +46,9 @@ struct sunxi_mmc {
u32 cbda; /* 0x94 */
u32 res2[26];
#if defined(CONFIG_SUNXI_GEN_SUN6I) || defined(CONFIG_MACH_SUN50I_H6)
- u32 res3[64];
+ u32 res3[17];
+ u32 samp_dl;
+ u32 res4[46];
#endif
u32 fifo; /* 0x100 / 0x200 FIFO access address */
};
@@ -130,5 +132,7 @@ struct sunxi_mmc {
#define SUNXI_MMC_COMMON_CLK_GATE (1 << 16)
#define SUNXI_MMC_COMMON_RESET (1 << 18)
+#define SUNXI_MMC_CAL_DL_SW_EN (0x1 << 7)
+
struct mmc *sunxi_mmc_init(int sdc_no);
#endif /* _SUNXI_MMC_H */
diff --git a/drivers/mmc/sunxi_mmc.c b/drivers/mmc/sunxi_mmc.c
index 39f15eb423..147eb9b4d5 100644
--- a/drivers/mmc/sunxi_mmc.c
+++ b/drivers/mmc/sunxi_mmc.c
@@ -99,11 +99,16 @@ static int mmc_set_mod_clk(struct sunxi_mmc_priv *priv, unsigned int hz)
{
unsigned int pll, pll_hz, div, n, oclk_dly, sclk_dly;
bool new_mode = false;
+ bool calibrate = false;
u32 val = 0;
if (IS_ENABLED(CONFIG_MMC_SUNXI_HAS_NEW_MODE) && (priv->mmc_no == 2))
new_mode = true;
+#if defined(CONFIG_MACH_SUN50I) || defined(CONFIG_MACH_SUN50I_H6)
+ calibrate = true;
+#endif
+
/*
* The MMC clock has an extra /2 post-divider when operating in the new
* mode.
@@ -174,7 +179,11 @@ static int mmc_set_mod_clk(struct sunxi_mmc_priv *priv, unsigned int hz)
val = CCM_MMC_CTRL_MODE_SEL_NEW;
setbits_le32(&priv->reg->ntsr, SUNXI_MMC_NTSR_MODE_SEL_NEW);
#endif
- } else {
+ } else if (!calibrate) {
+ /*
+ * Use hardcoded delay values if controller doesn't support
+ * calibration
+ */
val = CCM_MMC_CTRL_OCLK_DLY(oclk_dly) |
CCM_MMC_CTRL_SCLK_DLY(sclk_dly);
}
@@ -228,6 +237,16 @@ static int mmc_config_clock(struct sunxi_mmc_priv *priv, struct mmc *mmc)
rval &= ~SUNXI_MMC_CLK_DIVIDER_MASK;
writel(rval, &priv->reg->clkcr);
+#if defined(CONFIG_MACH_SUN50I) || defined(CONFIG_MACH_SUN50I_H6)
+ /* A64 supports calibration of delays on MMC controller and we
+ * have to set delay of zero before starting calibration.
+ * Allwinner BSP driver sets a delay only in the case of
+ * using HS400 which is not supported by mainline U-Boot or
+ * Linux at the moment
+ */
+ writel(SUNXI_MMC_CAL_DL_SW_EN, &priv->reg->samp_dl);
+#endif
+
/* Re-enable Clock */
rval |= SUNXI_MMC_CLK_ENABLE;
writel(rval, &priv->reg->clkcr);
--
2.19.1
^ permalink raw reply related [flat|nested] 6+ messages in thread* [U-Boot] [PATCH v5 2/4] dm: video: bridge: don't fail to activate bridge if reset or sleep GPIO is missing
2018-11-06 4:24 [U-Boot] [PATCH v5 0/4] Add support for Pinebook Vasily Khoruzhick
2018-11-06 4:24 ` [U-Boot] [PATCH v5 1/4] mmc: sunxi: add support for automatic delay calibration Vasily Khoruzhick
@ 2018-11-06 4:24 ` Vasily Khoruzhick
2018-11-06 4:24 ` [U-Boot] [PATCH v5 3/4] sun50i: A64: add support for R_I2C controller Vasily Khoruzhick
` (2 subsequent siblings)
4 siblings, 0 replies; 6+ messages in thread
From: Vasily Khoruzhick @ 2018-11-06 4:24 UTC (permalink / raw)
To: u-boot
Both GPIOs are optional, so we shouldn't fail if any is missing.
Without this fix reset is not deasserted if sleep GPIO is missing.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Cc: Vagrant Cascadian <vagrant@debian.org>
---
drivers/video/bridge/video-bridge-uclass.c | 16 +++++++++++-----
1 file changed, 11 insertions(+), 5 deletions(-)
diff --git a/drivers/video/bridge/video-bridge-uclass.c b/drivers/video/bridge/video-bridge-uclass.c
index cd4959cc71..5fecb4cfd5 100644
--- a/drivers/video/bridge/video-bridge-uclass.c
+++ b/drivers/video/bridge/video-bridge-uclass.c
@@ -106,13 +106,19 @@ static int video_bridge_pre_probe(struct udevice *dev)
int video_bridge_set_active(struct udevice *dev, bool active)
{
struct video_bridge_priv *uc_priv = dev_get_uclass_priv(dev);
- int ret;
+ int ret = 0;
debug("%s: %d\n", __func__, active);
- ret = dm_gpio_set_value(&uc_priv->sleep, !active);
- if (ret)
- return ret;
- if (active) {
+ if (uc_priv->sleep.dev) {
+ ret = dm_gpio_set_value(&uc_priv->sleep, !active);
+ if (ret)
+ return ret;
+ }
+
+ if (!active)
+ return 0;
+
+ if (uc_priv->reset.dev) {
ret = dm_gpio_set_value(&uc_priv->reset, true);
if (ret)
return ret;
--
2.19.1
^ permalink raw reply related [flat|nested] 6+ messages in thread* [U-Boot] [PATCH v5 3/4] sun50i: A64: add support for R_I2C controller
2018-11-06 4:24 [U-Boot] [PATCH v5 0/4] Add support for Pinebook Vasily Khoruzhick
2018-11-06 4:24 ` [U-Boot] [PATCH v5 1/4] mmc: sunxi: add support for automatic delay calibration Vasily Khoruzhick
2018-11-06 4:24 ` [U-Boot] [PATCH v5 2/4] dm: video: bridge: don't fail to activate bridge if reset or sleep GPIO is missing Vasily Khoruzhick
@ 2018-11-06 4:24 ` Vasily Khoruzhick
2018-11-06 4:24 ` [U-Boot] [PATCH v5 4/4] sunxi: DT: add support for Pinebook Vasily Khoruzhick
2018-11-13 16:41 ` [U-Boot] [PATCH v5 0/4] Add " Jagan Teki
4 siblings, 0 replies; 6+ messages in thread
From: Vasily Khoruzhick @ 2018-11-06 4:24 UTC (permalink / raw)
To: u-boot
Allwinner A64 has a I2C controller, which is in the R_ MMIO zone and has
two groups of pinmuxes on PL bank, so it's called R_I2C.
Add support for this I2C controller and the pinmux which doesn't conflict
with RSB.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Vagrant Cascadian <vagrant@debian.org>
---
arch/arm/include/asm/arch-sunxi/gpio.h | 1 +
arch/arm/mach-sunxi/Kconfig | 1 +
board/sunxi/board.c | 6 ++++++
3 files changed, 8 insertions(+)
diff --git a/arch/arm/include/asm/arch-sunxi/gpio.h b/arch/arm/include/asm/arch-sunxi/gpio.h
index 6a5eafc3d3..2daf23f6f5 100644
--- a/arch/arm/include/asm/arch-sunxi/gpio.h
+++ b/arch/arm/include/asm/arch-sunxi/gpio.h
@@ -211,6 +211,7 @@ enum sunxi_gpio_number {
#define SUN8I_H3_GPL_R_TWI 2
#define SUN8I_A23_GPL_R_TWI 3
#define SUN8I_GPL_R_UART 2
+#define SUN50I_GPL_R_TWI 2
#define SUN9I_GPN_R_RSB 3
diff --git a/arch/arm/mach-sunxi/Kconfig b/arch/arm/mach-sunxi/Kconfig
index 6277abc3cc..560dc9b25d 100644
--- a/arch/arm/mach-sunxi/Kconfig
+++ b/arch/arm/mach-sunxi/Kconfig
@@ -278,6 +278,7 @@ config MACH_SUN50I
select ARM64
select DM_I2C
select PHY_SUN4I_USB
+ select SUN6I_PRCM
select SUNXI_DE2
select SUNXI_GEN_SUN6I
select SUPPORT_SPL
diff --git a/board/sunxi/board.c b/board/sunxi/board.c
index b196d48674..64ccbc7245 100644
--- a/board/sunxi/board.c
+++ b/board/sunxi/board.c
@@ -168,10 +168,16 @@ void i2c_init_board(void)
#endif
#ifdef CONFIG_R_I2C_ENABLE
+#ifdef CONFIG_MACH_SUN50I
+ clock_twi_onoff(5, 1);
+ sunxi_gpio_set_cfgpin(SUNXI_GPL(8), SUN50I_GPL_R_TWI);
+ sunxi_gpio_set_cfgpin(SUNXI_GPL(9), SUN50I_GPL_R_TWI);
+#else
clock_twi_onoff(5, 1);
sunxi_gpio_set_cfgpin(SUNXI_GPL(0), SUN8I_H3_GPL_R_TWI);
sunxi_gpio_set_cfgpin(SUNXI_GPL(1), SUN8I_H3_GPL_R_TWI);
#endif
+#endif
}
#if defined(CONFIG_ENV_IS_IN_MMC) && defined(CONFIG_ENV_IS_IN_FAT)
--
2.19.1
^ permalink raw reply related [flat|nested] 6+ messages in thread* [U-Boot] [PATCH v5 4/4] sunxi: DT: add support for Pinebook
2018-11-06 4:24 [U-Boot] [PATCH v5 0/4] Add support for Pinebook Vasily Khoruzhick
` (2 preceding siblings ...)
2018-11-06 4:24 ` [U-Boot] [PATCH v5 3/4] sun50i: A64: add support for R_I2C controller Vasily Khoruzhick
@ 2018-11-06 4:24 ` Vasily Khoruzhick
2018-11-13 16:41 ` [U-Boot] [PATCH v5 0/4] Add " Jagan Teki
4 siblings, 0 replies; 6+ messages in thread
From: Vasily Khoruzhick @ 2018-11-06 4:24 UTC (permalink / raw)
To: u-boot
Pinebook is a laptop produced by Pine64, with USB-connected keyboard,
USB-connected touchpad and an eDP LCD panel connected via a RGB-eDP
bridge from Analogix.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Vagrant Cascadian <vagrant@debian.org>
---
arch/arm/dts/Makefile | 1 +
arch/arm/dts/sun50i-a64-pinebook-u-boot.dtsi | 15 +
arch/arm/dts/sun50i-a64-pinebook.dts | 294 +++++++++++++++++++
configs/pinebook_defconfig | 22 ++
4 files changed, 332 insertions(+)
create mode 100644 arch/arm/dts/sun50i-a64-pinebook-u-boot.dtsi
create mode 100644 arch/arm/dts/sun50i-a64-pinebook.dts
create mode 100644 configs/pinebook_defconfig
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index d36447d18d..7778f15091 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -405,6 +405,7 @@ dtb-$(CONFIG_MACH_SUN50I) += \
sun50i-a64-orangepi-win.dtb \
sun50i-a64-pine64-plus.dtb \
sun50i-a64-pine64.dtb \
+ sun50i-a64-pinebook.dtb \
sun50i-a64-sopine-baseboard.dtb
dtb-$(CONFIG_MACH_SUN9I) += \
sun9i-a80-optimus.dtb \
diff --git a/arch/arm/dts/sun50i-a64-pinebook-u-boot.dtsi b/arch/arm/dts/sun50i-a64-pinebook-u-boot.dtsi
new file mode 100644
index 0000000000..a99b7171d0
--- /dev/null
+++ b/arch/arm/dts/sun50i-a64-pinebook-u-boot.dtsi
@@ -0,0 +1,15 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2018 Vasily Khoruzhick <anarsoul@gmail.com>
+ *
+ */
+
+/* The ANX6345 eDP-bridge is on r_i2c */
+&r_i2c {
+ anx6345: edp-bridge at 38 {
+ compatible = "analogix,anx6345";
+ reg = <0x38>;
+ reset-gpios = <&pio 3 24 GPIO_ACTIVE_LOW>; /* PD24 */
+ status = "okay";
+ };
+};
diff --git a/arch/arm/dts/sun50i-a64-pinebook.dts b/arch/arm/dts/sun50i-a64-pinebook.dts
new file mode 100644
index 0000000000..ec537c5297
--- /dev/null
+++ b/arch/arm/dts/sun50i-a64-pinebook.dts
@@ -0,0 +1,294 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.xyz>
+ * Copyright (C) 2018 Vasily Khoruzhick <anarsoul@gmail.com>
+ *
+ */
+
+/dts-v1/;
+
+#include "sun50i-a64.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+ model = "Pinebook";
+ compatible = "pine64,pinebook", "allwinner,sun50i-a64";
+
+ aliases {
+ serial0 = &uart0;
+ ethernet0 = &rtl8723cs;
+ };
+
+ vdd_bl: regulator at 0 {
+ compatible = "regulator-fixed";
+ regulator-name = "bl-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&pio 7 6 GPIO_ACTIVE_HIGH>; /* PH6 */
+ enable-active-high;
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm 0 50000 0>;
+ brightness-levels = <0 5 10 15 20 30 40 55 70 85 100>;
+ default-brightness-level = <2>;
+ enable-gpios = <&pio 3 23 GPIO_ACTIVE_HIGH>; /* PD23 */
+ power-supply = <&vdd_bl>;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+
+ framebuffer-lcd {
+ panel-supply = <®_dc1sw>;
+ dvdd25-supply = <®_dldo2>;
+ dvdd12-supply = <®_fldo1>;
+ };
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+
+ lid_switch {
+ label = "Lid Switch";
+ gpios = <&r_pio 0 12 GPIO_ACTIVE_LOW>; /* PL12 */
+ linux,input-type = <EV_SW>;
+ linux,code = <SW_LID>;
+ linux,can-disable;
+ wakeup-source;
+ };
+ };
+
+ reg_vcc3v3: vcc3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
+ };
+};
+
+&ehci0 {
+ phys = <&usbphy 0>;
+ phy-names = "usb";
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins>;
+ vmmc-supply = <®_dcdc1>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
+ disable-wp;
+ bus-width = <4>;
+ status = "okay";
+};
+
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins>;
+ vmmc-supply = <®_dldo4>;
+ vqmmc-supply = <®_eldo1>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+
+ rtl8723cs: wifi at 1 {
+ reg = <1>;
+ };
+};
+
+&mmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_pins>, <&mmc2_ds_pin>;
+ vmmc-supply = <®_dcdc1>;
+ vqmmc-supply = <®_eldo1>;
+ bus-width = <8>;
+ non-removable;
+ cap-mmc-hw-reset;
+ mmc-hs200-1_8v;
+ status = "okay";
+};
+
+&ohci0 {
+ phys = <&usbphy 0>;
+ phy-names = "usb";
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&pwm {
+ status = "okay";
+};
+
+&r_rsb {
+ status = "okay";
+
+ axp803: pmic at 3a3 {
+ compatible = "x-powers,axp803";
+ reg = <0x3a3>;
+ interrupt-parent = <&r_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+/* The ANX6345 eDP-bridge is on r_i2c */
+&r_i2c {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&r_i2c_pl89_pins>;
+ status = "okay";
+};
+
+#include "axp803.dtsi"
+
+®_aldo1 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-name = "vcc-csi";
+};
+
+®_aldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-pl";
+};
+
+®_aldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-pll-avcc";
+};
+
+®_dc1sw {
+ regulator-name = "vcc-lcd";
+};
+
+®_dcdc1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-3v3";
+};
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-name = "vdd-cpux";
+};
+
+/* DCDC3 is polyphased with DCDC2 */
+
+®_dcdc5 {
+ regulator-always-on;
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-name = "vcc-dram";
+};
+
+®_dcdc6 {
+ regulator-always-on;
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-sys";
+};
+
+®_dldo1 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-hdmi";
+};
+
+®_dldo2 {
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ regulator-name = "vcc-edp";
+};
+
+®_dldo3 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "avdd-csi";
+};
+
+®_dldo4 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi";
+};
+
+®_eldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "cpvdd";
+};
+
+®_eldo3 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vdd-1v8-csi";
+};
+
+®_fldo1 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-name = "vcc-1v2-hsic";
+};
+
+®_fldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-cpus";
+};
+
+®_ldo_io0 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-usb";
+ status = "okay";
+};
+
+®_rtc_ldo {
+ regulator-name = "vcc-rtc";
+};
+
+&simplefb_hdmi {
+ vcc-hdmi-supply = <®_dldo1>;
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pb_pins>;
+ status = "okay";
+};
+
+&usb_otg {
+ dr_mode = "host";
+};
+
+&usbphy {
+ usb0_vbus-supply = <®_ldo_io0>;
+ usb1_vbus-supply = <®_ldo_io0>;
+ status = "okay";
+};
diff --git a/configs/pinebook_defconfig b/configs/pinebook_defconfig
new file mode 100644
index 0000000000..5294dbd2eb
--- /dev/null
+++ b/configs/pinebook_defconfig
@@ -0,0 +1,22 @@
+CONFIG_ARM=y
+CONFIG_ARCH_SUNXI=y
+CONFIG_SPL=y
+CONFIG_MACH_SUN50I=y
+CONFIG_SUNXI_DRAM_LPDDR3_STOCK=y
+CONFIG_DRAM_CLK=552
+CONFIG_DRAM_ZQ=3881949
+CONFIG_MMC_SUNXI_SLOT_EXTRA=2
+CONFIG_R_I2C_ENABLE=y
+# CONFIG_CMD_FLASH is not set
+# CONFIG_SPL_DOS_PARTITION is not set
+# CONFIG_SPL_EFI_PARTITION is not set
+CONFIG_DEFAULT_DEVICE_TREE="sun50i-a64-pinebook"
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_PWM=y
+CONFIG_PWM_SUNXI=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_SYS_USB_EVENT_POLL_VIA_INT_QUEUE=y
+# CONFIG_USB_GADGET is not set
+CONFIG_VIDEO_BRIDGE=y
+CONFIG_VIDEO_BRIDGE_ANALOGIX_ANX6345=y
--
2.19.1
^ permalink raw reply related [flat|nested] 6+ messages in thread* [U-Boot] [PATCH v5 0/4] Add support for Pinebook
2018-11-06 4:24 [U-Boot] [PATCH v5 0/4] Add support for Pinebook Vasily Khoruzhick
` (3 preceding siblings ...)
2018-11-06 4:24 ` [U-Boot] [PATCH v5 4/4] sunxi: DT: add support for Pinebook Vasily Khoruzhick
@ 2018-11-13 16:41 ` Jagan Teki
4 siblings, 0 replies; 6+ messages in thread
From: Jagan Teki @ 2018-11-13 16:41 UTC (permalink / raw)
To: u-boot
On Tue, Nov 6, 2018 at 9:55 AM Vasily Khoruzhick <anarsoul@gmail.com> wrote:
>
> This series adds support for the Pinebook, an allwinner A64 laptop
> produced by Pine64. It also adds support for mmc delay calibration,
> R_I2C controller, and addresses the issue with activating video
> bridge when any of GPIOs is missing.
>
> This series depends on André's "sunxi: A64/H3/H5 DT updates"
>
> v2: - sync sun50i-a64.dtsi with linux instead of adding missing nodes
> - take sun50i-a64-pinebook.dts from linux
> - don't introduce new Kconfig for A64 MMC calibration
> - improve code in video bridge uclass to check for presensce of
> GPIO instead of ingoring EINVAL errors
> v3: - enable calibration for H6 as well
> - init ret variable in video_bridge_set_active()
> - fix order of dts files Makefile
> - split anx6345 binding into sun50i-a64-pinebook-u-boot.dts
> - drop speaker_amp node from pinebook dts
> - drop unnecessary options from defconfig
> v4: - sync device tree files with linux-next
> v5: - drop patch to sync device tree files with linux-next
>
> Vasily Khoruzhick (4):
> mmc: sunxi: add support for automatic delay calibration
> dm: video: bridge: don't fail to activate bridge if reset or sleep
> GPIO is missing
> sun50i: A64: add support for R_I2C controller
> sunxi: DT: add support for Pinebook
Applied to u-boot-sunxi/master
^ permalink raw reply [flat|nested] 6+ messages in thread