* [PATCH] arm: dts: mvebu: Update DTS for Thecus N2350 board @ 2024-06-10 0:34 Tony Dinh 2024-06-10 1:07 ` Dragan Simic 0 siblings, 1 reply; 4+ messages in thread From: Tony Dinh @ 2024-06-10 0:34 UTC (permalink / raw) To: U-Boot Mailing List, Stefan Roese Cc: Tom Rini, Tony Dinh, This contributor prefers not to receive mails - Change the spi-max-frequency to 50000000 (50 Mhz). According to the data sheet[1], the MX25L3205D max frequency is 86 Mhz. Using 50 Mhz in the DTS to ensure u-boot is consistent with what Linux kernel expected. - Update GPIO fan to conform to the latest DT binding. [1] MX25L3205D-MX25L1605D-MX25L6405D-Macronix-MX25L3205DM2I-12G-datasheet.pdf Signed-off-by: Tony Dinh <mibodhi@gmail.com> --- arch/arm/dts/armada-385-thecus-n2350.dts | 10 +++++----- 1 file changed, 5 insertions(+), 5 deletions(-) diff --git a/arch/arm/dts/armada-385-thecus-n2350.dts b/arch/arm/dts/armada-385-thecus-n2350.dts index 253cf01130..fdaa444e51 100644 --- a/arch/arm/dts/armada-385-thecus-n2350.dts +++ b/arch/arm/dts/armada-385-thecus-n2350.dts @@ -2,7 +2,7 @@ /* * Device Tree file for Thecus N2350 board * - * Copyright (C) 2018-2023 Tony Dinh <mibodhi@gmail.com> + * Copyright (C) 2018-2024 Tony Dinh <mibodhi@gmail.com> * Copyright (C) 2018 Manuel Jung <manuel.jung@hotmail.com> */ @@ -143,9 +143,9 @@ fan { compatible = "gpio-fan"; gpios = <&gpio1 16 GPIO_ACTIVE_HIGH>; - gpio-fan,speed-map = < 0 0 - 600 1 - 3000 2 >; + gpio-fan,speed-map = < 0 0>, + <600 1>, + <3000 2 >; pinctrl-0 = <&pmx_fan>; pinctrl-names = "default"; }; @@ -415,7 +415,7 @@ compatible = "jedec,spi-nor"; reg = <0>; - spi-max-frequency = <108000000>; + spi-max-frequency = <50000000>; spi-cpha; partition@0 { -- 2.39.2 ^ permalink raw reply related [flat|nested] 4+ messages in thread
* Re: [PATCH] arm: dts: mvebu: Update DTS for Thecus N2350 board 2024-06-10 0:34 [PATCH] arm: dts: mvebu: Update DTS for Thecus N2350 board Tony Dinh @ 2024-06-10 1:07 ` Dragan Simic 2024-06-11 21:42 ` Tony Dinh 0 siblings, 1 reply; 4+ messages in thread From: Dragan Simic @ 2024-06-10 1:07 UTC (permalink / raw) To: Tony Dinh; +Cc: U-Boot Mailing List, Stefan Roese, Tom Rini Hello Tony, Please see a few comments below. On 2024-06-10 02:34, Tony Dinh wrote: > - Change the spi-max-frequency to 50000000 (50 Mhz). According to the > data sheet[1], the MX25L3205D max frequency is 86 Mhz. Using 50 Mhz in > the DTS to ensure u-boot is consistent with what Linux kernel expected. > - Update GPIO fan to conform to the latest DT binding. There's no need for the bullet points, plain prose will do fine instead. > [1] > MX25L3205D-MX25L1605D-MX25L6405D-Macronix-MX25L3205DM2I-12G-datasheet.pdf Unless you can provide a real, working URL for the datasheet, this reference should actually be deleted. > Signed-off-by: Tony Dinh <mibodhi@gmail.com> > --- > > arch/arm/dts/armada-385-thecus-n2350.dts | 10 +++++----- > 1 file changed, 5 insertions(+), 5 deletions(-) > > diff --git a/arch/arm/dts/armada-385-thecus-n2350.dts > b/arch/arm/dts/armada-385-thecus-n2350.dts > index 253cf01130..fdaa444e51 100644 > --- a/arch/arm/dts/armada-385-thecus-n2350.dts > +++ b/arch/arm/dts/armada-385-thecus-n2350.dts > @@ -2,7 +2,7 @@ > /* > * Device Tree file for Thecus N2350 board > * > - * Copyright (C) 2018-2023 Tony Dinh <mibodhi@gmail.com> > + * Copyright (C) 2018-2024 Tony Dinh <mibodhi@gmail.com> > * Copyright (C) 2018 Manuel Jung <manuel.jung@hotmail.com> > */ > > @@ -143,9 +143,9 @@ > fan { > compatible = "gpio-fan"; > gpios = <&gpio1 16 GPIO_ACTIVE_HIGH>; > - gpio-fan,speed-map = < 0 0 > - 600 1 > - 3000 2 >; > + gpio-fan,speed-map = < 0 0>, > + <600 1>, > + <3000 2 >; > pinctrl-0 = <&pmx_fan>; > pinctrl-names = "default"; > }; > @@ -415,7 +415,7 @@ > compatible = "jedec,spi-nor"; > reg = <0>; > > - spi-max-frequency = <108000000>; > + spi-max-frequency = <50000000>; > spi-cpha; > > partition@0 { ^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [PATCH] arm: dts: mvebu: Update DTS for Thecus N2350 board 2024-06-10 1:07 ` Dragan Simic @ 2024-06-11 21:42 ` Tony Dinh 2024-07-08 14:15 ` Stefan Roese 0 siblings, 1 reply; 4+ messages in thread From: Tony Dinh @ 2024-06-11 21:42 UTC (permalink / raw) To: Dragan Simic; +Cc: U-Boot Mailing List, Stefan Roese, Tom Rini Hi Dragan, On Sun, Jun 9, 2024 at 6:07 PM Dragan Simic <dsimic@manjaro.org> wrote: > > Hello Tony, > > Please see a few comments below. > > On 2024-06-10 02:34, Tony Dinh wrote: > > - Change the spi-max-frequency to 50000000 (50 Mhz). According to the > > data sheet[1], the MX25L3205D max frequency is 86 Mhz. Using 50 Mhz in > > the DTS to ensure u-boot is consistent with what Linux kernel expected. > > - Update GPIO fan to conform to the latest DT binding. > > There's no need for the bullet points, plain prose will do fine instead. I like bullet points :) All my patch descriptions have bullet points when there are 2 or more different items. > > > [1] > > MX25L3205D-MX25L1605D-MX25L6405D-Macronix-MX25L3205DM2I-12G-datasheet.pdf > > Unless you can provide a real, working URL for the datasheet, this > reference > should actually be deleted. It was my oversight. That should have been this URL: https://www.macronix.com/Lists/Datasheet/Attachments/8575/MX25L3205D,%203V,%2032Mb,%20v1.5.pdf I'll wait for Stefan to review the patch and let him decide whether I should send in a V2 patch or he will modify the commit description. Thanks for the comments! All the best, Tony > > > Signed-off-by: Tony Dinh <mibodhi@gmail.com> > > --- > > > > arch/arm/dts/armada-385-thecus-n2350.dts | 10 +++++----- > > 1 file changed, 5 insertions(+), 5 deletions(-) > > > > diff --git a/arch/arm/dts/armada-385-thecus-n2350.dts > > b/arch/arm/dts/armada-385-thecus-n2350.dts > > index 253cf01130..fdaa444e51 100644 > > --- a/arch/arm/dts/armada-385-thecus-n2350.dts > > +++ b/arch/arm/dts/armada-385-thecus-n2350.dts > > @@ -2,7 +2,7 @@ > > /* > > * Device Tree file for Thecus N2350 board > > * > > - * Copyright (C) 2018-2023 Tony Dinh <mibodhi@gmail.com> > > + * Copyright (C) 2018-2024 Tony Dinh <mibodhi@gmail.com> > > * Copyright (C) 2018 Manuel Jung <manuel.jung@hotmail.com> > > */ > > > > @@ -143,9 +143,9 @@ > > fan { > > compatible = "gpio-fan"; > > gpios = <&gpio1 16 GPIO_ACTIVE_HIGH>; > > - gpio-fan,speed-map = < 0 0 > > - 600 1 > > - 3000 2 >; > > + gpio-fan,speed-map = < 0 0>, > > + <600 1>, > > + <3000 2 >; > > pinctrl-0 = <&pmx_fan>; > > pinctrl-names = "default"; > > }; > > @@ -415,7 +415,7 @@ > > compatible = "jedec,spi-nor"; > > reg = <0>; > > > > - spi-max-frequency = <108000000>; > > + spi-max-frequency = <50000000>; > > spi-cpha; > > > > partition@0 { ^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [PATCH] arm: dts: mvebu: Update DTS for Thecus N2350 board 2024-06-11 21:42 ` Tony Dinh @ 2024-07-08 14:15 ` Stefan Roese 0 siblings, 0 replies; 4+ messages in thread From: Stefan Roese @ 2024-07-08 14:15 UTC (permalink / raw) To: Tony Dinh, Dragan Simic; +Cc: U-Boot Mailing List, Tom Rini On 6/11/24 23:42, Tony Dinh wrote: > Hi Dragan, > > On Sun, Jun 9, 2024 at 6:07 PM Dragan Simic <dsimic@manjaro.org> wrote: >> >> Hello Tony, >> >> Please see a few comments below. >> >> On 2024-06-10 02:34, Tony Dinh wrote: >>> - Change the spi-max-frequency to 50000000 (50 Mhz). According to the >>> data sheet[1], the MX25L3205D max frequency is 86 Mhz. Using 50 Mhz in >>> the DTS to ensure u-boot is consistent with what Linux kernel expected. >>> - Update GPIO fan to conform to the latest DT binding. >> >> There's no need for the bullet points, plain prose will do fine instead. > > I like bullet points :) All my patch descriptions have bullet points > when there are 2 or more different items. > >> >>> [1] >>> MX25L3205D-MX25L1605D-MX25L6405D-Macronix-MX25L3205DM2I-12G-datasheet.pdf >> >> Unless you can provide a real, working URL for the datasheet, this >> reference >> should actually be deleted. > > It was my oversight. That should have been this URL: > > https://www.macronix.com/Lists/Datasheet/Attachments/8575/MX25L3205D,%203V,%2032Mb,%20v1.5.pdf > > I'll wait for Stefan to review the patch and let him decide whether I > should send in a V2 patch or he will modify the commit description. I've changed the commit message accordingly. Applied to u-boot-marvell/master Thanks, Stefan > Thanks for the comments! > > All the best, > Tony > >> >>> Signed-off-by: Tony Dinh <mibodhi@gmail.com> >>> --- >>> >>> arch/arm/dts/armada-385-thecus-n2350.dts | 10 +++++----- >>> 1 file changed, 5 insertions(+), 5 deletions(-) >>> >>> diff --git a/arch/arm/dts/armada-385-thecus-n2350.dts >>> b/arch/arm/dts/armada-385-thecus-n2350.dts >>> index 253cf01130..fdaa444e51 100644 >>> --- a/arch/arm/dts/armada-385-thecus-n2350.dts >>> +++ b/arch/arm/dts/armada-385-thecus-n2350.dts >>> @@ -2,7 +2,7 @@ >>> /* >>> * Device Tree file for Thecus N2350 board >>> * >>> - * Copyright (C) 2018-2023 Tony Dinh <mibodhi@gmail.com> >>> + * Copyright (C) 2018-2024 Tony Dinh <mibodhi@gmail.com> >>> * Copyright (C) 2018 Manuel Jung <manuel.jung@hotmail.com> >>> */ >>> >>> @@ -143,9 +143,9 @@ >>> fan { >>> compatible = "gpio-fan"; >>> gpios = <&gpio1 16 GPIO_ACTIVE_HIGH>; >>> - gpio-fan,speed-map = < 0 0 >>> - 600 1 >>> - 3000 2 >; >>> + gpio-fan,speed-map = < 0 0>, >>> + <600 1>, >>> + <3000 2 >; >>> pinctrl-0 = <&pmx_fan>; >>> pinctrl-names = "default"; >>> }; >>> @@ -415,7 +415,7 @@ >>> compatible = "jedec,spi-nor"; >>> reg = <0>; >>> >>> - spi-max-frequency = <108000000>; >>> + spi-max-frequency = <50000000>; >>> spi-cpha; >>> >>> partition@0 { Viele Grüße, Stefan Roese -- DENX Software Engineering GmbH, Managing Director: Erika Unter HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-51 Fax: (+49)-8142-66989-80 Email: sr@denx.de ^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2024-07-08 14:15 UTC | newest] Thread overview: 4+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2024-06-10 0:34 [PATCH] arm: dts: mvebu: Update DTS for Thecus N2350 board Tony Dinh 2024-06-10 1:07 ` Dragan Simic 2024-06-11 21:42 ` Tony Dinh 2024-07-08 14:15 ` Stefan Roese
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox