From: Anshul Dalal <anshuld@ti.com>
To: <u-boot@lists.denx.de>
Cc: Anshul Dalal <anshuld@ti.com>, <d-gole@ti.com>, <b-padhi@ti.com>,
<vigneshr@ti.com>, <trini@konsulko.com>, <nm@ti.com>,
<robertcnelson@gmail.com>, <w.egorov@phytec.de>,
<francesco.dolcini@toradex.com>, <ggiordano@phytec.com>,
<m-chawdhry@ti.com>, <afd@ti.com>, <bb@ti.com>, <u-kumar1@ti.com>,
<devarsht@ti.com>, <ilias.apalodimas@linaro.org>,
<xypron.glpk@gmx.de>
Subject: [PATCH v11 07/11] arm: armv8: mmu: add mmu_unmap_reserved_mem
Date: Fri, 17 Oct 2025 18:45:29 +0530 [thread overview]
Message-ID: <20251017131540.3636067-8-anshuld@ti.com> (raw)
In-Reply-To: <20251017131540.3636067-1-anshuld@ti.com>
For armv8, U-Boot uses a static map defined as 'mem_map' for configuring
the MMU's page tables, done by mmu_setup.
Though this works well for simpler platforms, it makes creating runtime
carveouts by modifying the static array at runtime exceedingly complex
like in mach-snapdragon/board.c.
Creation of such carveouts are much better handled by APIs such as
mmu_change_region_attr once the page tables are configured. Usually such
carveouts are configured via the device-tree's reserved-memory node
which provides the address and size for the carveout.
Therefore this patch adds mmu_unmap_reserved_mem which acts as a wrapper
over mmu_change_region_attr, helping unmap a reserved-memory region.
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Anshul Dalal <anshuld@ti.com>
Tested-by: Wadim Egorov <w.egorov@phytec.de>
---
arch/arm/cpu/armv8/cache_v8.c | 26 ++++++++++++++++++++++++++
arch/arm/include/asm/armv8/mmu.h | 9 +++++++++
2 files changed, 35 insertions(+)
diff --git a/arch/arm/cpu/armv8/cache_v8.c b/arch/arm/cpu/armv8/cache_v8.c
index 9b3c37dae82..672ec16d483 100644
--- a/arch/arm/cpu/armv8/cache_v8.c
+++ b/arch/arm/cpu/armv8/cache_v8.c
@@ -86,6 +86,32 @@ int mem_map_from_dram_banks(unsigned int index, unsigned int len, u64 attrs)
return 0;
}
+
+int mmu_unmap_reserved_mem(const char *name, bool check_nomap)
+{
+ void *fdt = (void *)gd->fdt_blob;
+ char node_path[128];
+ fdt_addr_t addr;
+ fdt_size_t size;
+ int ret;
+
+ snprintf(node_path, sizeof(node_path), "/reserved-memory/%s", name);
+ ret = fdt_path_offset(fdt, node_path);
+ if (ret < 0)
+ return ret;
+
+ if (check_nomap && !fdtdec_get_bool(fdt, ret, "no-map"))
+ return -EINVAL;
+
+ addr = fdtdec_get_addr_size(fdt, ret, "reg", &size);
+ if (addr == FDT_ADDR_T_NONE)
+ return -1;
+
+ mmu_change_region_attr_nobreak(addr, size, PTE_TYPE_FAULT);
+
+ return 0;
+}
+
u64 get_tcr(u64 *pips, u64 *pva_bits)
{
int el = get_effective_el();
diff --git a/arch/arm/include/asm/armv8/mmu.h b/arch/arm/include/asm/armv8/mmu.h
index 6e7a3366844..8aa5f9721c4 100644
--- a/arch/arm/include/asm/armv8/mmu.h
+++ b/arch/arm/include/asm/armv8/mmu.h
@@ -207,6 +207,15 @@ void setup_pgtables(void);
*/
int mem_map_from_dram_banks(unsigned int index, unsigned int len, u64 attrs);
+/**
+ * mmu_unmap_reserved_mem() - Unmaps a reserved-memory node as PTE_TYPE_FAULT
+ * once MMU is configured by mmu_setup.
+ *
+ * @name: The name of the node under "/reserved-memory/" path
+ * @check_nomap: Check if the node is marked "no-map" before unmapping it
+ */
+int mmu_unmap_reserved_mem(const char *name, bool check_nomap);
+
u64 get_tcr(u64 *pips, u64 *pva_bits);
/**
--
2.51.0
next prev parent reply other threads:[~2025-10-17 13:17 UTC|newest]
Thread overview: 19+ messages / expand[flat|nested] mbox.gz Atom feed top
2025-10-17 13:15 [PATCH v11 00/11] Add support for dynamic MMU configuration Anshul Dalal
2025-10-17 13:15 ` [PATCH v11 01/11] mach-k3: use minimal memory map for all K3 Anshul Dalal
2025-10-17 13:15 ` [PATCH v11 02/11] mach-k3: use custom enable_cache Anshul Dalal
2025-10-17 13:15 ` [PATCH v11 03/11] arm: armv8: mmu: export mmu_setup Anshul Dalal
2025-10-17 13:15 ` [PATCH v11 04/11] arm: armv8: invalidate dcache entries on dcache_enable Anshul Dalal
2025-10-17 13:15 ` [PATCH v11 05/11] arm: armv8: mmu: add mem_map_from_dram_banks Anshul Dalal
2025-10-17 13:15 ` [PATCH v11 06/11] mach-k3: map all banks using mem_map_from_dram_banks Anshul Dalal
2025-10-17 13:15 ` Anshul Dalal [this message]
2025-10-17 13:15 ` [PATCH v11 08/11] spl: split spl_board_fixups to arch/board specific Anshul Dalal
2025-10-17 13:15 ` [PATCH v11 09/11] mach-k3: add reserved memory fixups for next boot stage Anshul Dalal
2025-10-17 13:15 ` [PATCH v11 10/11] mach-k3: add carveouts for TFA and optee Anshul Dalal
2025-10-17 13:15 ` [PATCH v11 11/11] arm: mach-k3: reserve space for page table entries Anshul Dalal
2025-10-22 20:14 ` [PATCH v11 00/11] Add support for dynamic MMU configuration Tom Rini
2025-10-27 16:52 ` [REGRESSION] " Francesco Dolcini
2025-10-28 4:38 ` Anshul Dalal
2025-10-28 16:56 ` Emanuele Ghidoli
2025-10-29 8:58 ` Anshul Dalal
2025-10-31 11:00 ` Emanuele Ghidoli
2025-10-31 11:43 ` Anshul Dalal
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20251017131540.3636067-8-anshuld@ti.com \
--to=anshuld@ti.com \
--cc=afd@ti.com \
--cc=b-padhi@ti.com \
--cc=bb@ti.com \
--cc=d-gole@ti.com \
--cc=devarsht@ti.com \
--cc=francesco.dolcini@toradex.com \
--cc=ggiordano@phytec.com \
--cc=ilias.apalodimas@linaro.org \
--cc=m-chawdhry@ti.com \
--cc=nm@ti.com \
--cc=robertcnelson@gmail.com \
--cc=trini@konsulko.com \
--cc=u-boot@lists.denx.de \
--cc=u-kumar1@ti.com \
--cc=vigneshr@ti.com \
--cc=w.egorov@phytec.de \
--cc=xypron.glpk@gmx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox