* [PATCH 2/8] arm: dts: k3-am62a*: Sync with kernel v6.7-rc1
2023-11-13 14:51 [PATCH 0/8] arm: dts: am62a: Update to kernel v6.7-rc1 Nishanth Menon
2023-11-13 14:51 ` [PATCH 1/8] arm: mach-k3: am62a: Add main_timer0 id to the dev list Nishanth Menon
@ 2023-11-13 14:51 ` Nishanth Menon
2023-11-13 14:51 ` [PATCH 3/8] dma: ti: k3-udma: Introduce DMA support for the am62ax Nishanth Menon
` (5 subsequent siblings)
7 siblings, 0 replies; 12+ messages in thread
From: Nishanth Menon @ 2023-11-13 14:51 UTC (permalink / raw)
To: Heinrich Schuchardt, Tom Rini
Cc: Siddharth Vadapalli, Andrew Davis, Neha Malcom Francis,
Roger Quadros, Bryan Brattlof, Vignesh Raghavendra, Jai Luthra,
u-boot, Nishanth Menon
Sync with kernel v6.7-rc1 and sync up the u-boot dts files accordingly.
Signed-off-by: Nishanth Menon <nm@ti.com>
---
arch/arm/dts/k3-am62a-main.dtsi | 585 +++++++++++++++++++++++++-
arch/arm/dts/k3-am62a-mcu.dtsi | 131 ++++++
arch/arm/dts/k3-am62a-thermal.dtsi | 47 +++
arch/arm/dts/k3-am62a-wakeup.dtsi | 21 +-
arch/arm/dts/k3-am62a.dtsi | 5 +-
arch/arm/dts/k3-am62a7-r5-sk.dts | 74 +---
arch/arm/dts/k3-am62a7-sk-u-boot.dtsi | 139 ++++--
arch/arm/dts/k3-am62a7-sk.dts | 347 ++++++++++++++-
arch/arm/dts/k3-am62a7.dtsi | 3 +-
9 files changed, 1224 insertions(+), 128 deletions(-)
create mode 100644 arch/arm/dts/k3-am62a-thermal.dtsi
diff --git a/arch/arm/dts/k3-am62a-main.dtsi b/arch/arm/dts/k3-am62a-main.dtsi
index bc4b50bcd177..4ae7fdc5221b 100644
--- a/arch/arm/dts/k3-am62a-main.dtsi
+++ b/arch/arm/dts/k3-am62a-main.dtsi
@@ -48,6 +48,18 @@
#address-cells = <1>;
#size-cells = <1>;
ranges = <0x00 0x00 0x00100000 0x20000>;
+
+ phy_gmii_sel: phy@4044 {
+ compatible = "ti,am654-phy-gmii-sel";
+ reg = <0x4044 0x8>;
+ #phy-cells = <1>;
+ };
+
+ epwm_tbclk: clock-controller@4130 {
+ compatible = "ti,am62-epwm-tbclk";
+ reg = <0x4130 0x4>;
+ #clock-cells = <1>;
+ };
};
dmss: bus@48000000 {
@@ -69,6 +81,67 @@
interrupt-names = "rx_012";
interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
};
+
+ inta_main_dmss: interrupt-controller@48000000 {
+ compatible = "ti,sci-inta";
+ reg = <0x00 0x48000000 0x00 0x100000>;
+ #interrupt-cells = <0>;
+ interrupt-controller;
+ interrupt-parent = <&gic500>;
+ msi-controller;
+ ti,sci = <&dmsc>;
+ ti,sci-dev-id = <28>;
+ ti,interrupt-ranges = <6 70 34>;
+ ti,unmapped-event-sources = <&main_bcdma>, <&main_pktdma>;
+ };
+
+ main_bcdma: dma-controller@485c0100 {
+ compatible = "ti,am64-dmss-bcdma";
+ reg = <0x00 0x485c0100 0x00 0x100>,
+ <0x00 0x4c000000 0x00 0x20000>,
+ <0x00 0x4a820000 0x00 0x20000>,
+ <0x00 0x4aa40000 0x00 0x20000>,
+ <0x00 0x4bc00000 0x00 0x100000>;
+ reg-names = "gcfg", "bchanrt", "rchanrt", "tchanrt", "ringrt";
+ msi-parent = <&inta_main_dmss>;
+ #dma-cells = <3>;
+ ti,sci = <&dmsc>;
+ ti,sci-dev-id = <26>;
+ ti,sci-rm-range-bchan = <0x20>; /* BLOCK_COPY_CHAN */
+ ti,sci-rm-range-rchan = <0x21>; /* SPLIT_TR_RX_CHAN */
+ ti,sci-rm-range-tchan = <0x22>; /* SPLIT_TR_TX_CHAN */
+ };
+
+ main_pktdma: dma-controller@485c0000 {
+ compatible = "ti,am64-dmss-pktdma";
+ reg = <0x00 0x485c0000 0x00 0x100>,
+ <0x00 0x4a800000 0x00 0x20000>,
+ <0x00 0x4aa00000 0x00 0x40000>,
+ <0x00 0x4b800000 0x00 0x400000>;
+ reg-names = "gcfg", "rchanrt", "tchanrt", "ringrt";
+ msi-parent = <&inta_main_dmss>;
+ #dma-cells = <2>;
+ ti,sci = <&dmsc>;
+ ti,sci-dev-id = <30>;
+ ti,sci-rm-range-tchan = <0x23>, /* UNMAPPED_TX_CHAN */
+ <0x24>, /* CPSW_TX_CHAN */
+ <0x25>, /* SAUL_TX_0_CHAN */
+ <0x26>; /* SAUL_TX_1_CHAN */
+ ti,sci-rm-range-tflow = <0x10>, /* RING_UNMAPPED_TX_CHAN */
+ <0x11>, /* RING_CPSW_TX_CHAN */
+ <0x12>, /* RING_SAUL_TX_0_CHAN */
+ <0x13>; /* RING_SAUL_TX_1_CHAN */
+ ti,sci-rm-range-rchan = <0x29>, /* UNMAPPED_RX_CHAN */
+ <0x2b>, /* CPSW_RX_CHAN */
+ <0x2d>, /* SAUL_RX_0_CHAN */
+ <0x2f>, /* SAUL_RX_1_CHAN */
+ <0x31>, /* SAUL_RX_2_CHAN */
+ <0x33>; /* SAUL_RX_3_CHAN */
+ ti,sci-rm-range-rflow = <0x2a>, /* FLOW_UNMAPPED_RX_CHAN */
+ <0x2c>, /* FLOW_CPSW_RX_CHAN */
+ <0x2e>, /* FLOW_SAUL_RX_0/1_CHAN */
+ <0x32>; /* FLOW_SAUL_RX_2/3_CHAN */
+ };
};
dmsc: system-controller@44043000 {
@@ -77,8 +150,8 @@
reg-names = "debug_messages";
ti,host-id = <12>;
mbox-names = "rx", "tx";
- mboxes= <&secure_proxy_main 12>,
- <&secure_proxy_main 13>;
+ mboxes = <&secure_proxy_main 12>,
+ <&secure_proxy_main 13>;
k3_pds: power-controller {
compatible = "ti,sci-pm-domain";
@@ -96,6 +169,21 @@
};
};
+ secure_proxy_sa3: mailbox@43600000 {
+ compatible = "ti,am654-secure-proxy";
+ #mbox-cells = <1>;
+ reg-names = "target_data", "rt", "scfg";
+ reg = <0x00 0x43600000 0x00 0x10000>,
+ <0x00 0x44880000 0x00 0x20000>,
+ <0x00 0x44860000 0x00 0x20000>;
+ /*
+ * Marked Disabled:
+ * Node is incomplete as it is meant for bootloaders and
+ * firmware on non-MPU processors
+ */
+ status = "disabled";
+ };
+
main_pmx0: pinctrl@f4000 {
compatible = "pinctrl-single";
reg = <0x00 0xf4000 0x00 0x2ac>;
@@ -104,6 +192,102 @@
pinctrl-single,function-mask = <0xffffffff>;
};
+ main_timer0: timer@2400000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x2400000 0x00 0x400>;
+ interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 36 2>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 36 2>;
+ assigned-clock-parents = <&k3_clks 36 3>;
+ power-domains = <&k3_pds 36 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ main_timer1: timer@2410000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x2410000 0x00 0x400>;
+ interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 37 2>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 37 2>;
+ assigned-clock-parents = <&k3_clks 37 3>;
+ power-domains = <&k3_pds 37 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ main_timer2: timer@2420000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x2420000 0x00 0x400>;
+ interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 38 2>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 38 2>;
+ assigned-clock-parents = <&k3_clks 38 3>;
+ power-domains = <&k3_pds 38 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ main_timer3: timer@2430000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x2430000 0x00 0x400>;
+ interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 39 2>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 39 2>;
+ assigned-clock-parents = <&k3_clks 39 3>;
+ power-domains = <&k3_pds 39 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ main_timer4: timer@2440000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x2440000 0x00 0x400>;
+ interrupts = <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 40 2>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 40 2>;
+ assigned-clock-parents = <&k3_clks 40 3>;
+ power-domains = <&k3_pds 40 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ main_timer5: timer@2450000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x2450000 0x00 0x400>;
+ interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 41 2>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 41 2>;
+ assigned-clock-parents = <&k3_clks 41 3>;
+ power-domains = <&k3_pds 41 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ main_timer6: timer@2460000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x2460000 0x00 0x400>;
+ interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 42 2>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 42 2>;
+ assigned-clock-parents = <&k3_clks 42 3>;
+ power-domains = <&k3_pds 42 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ main_timer7: timer@2470000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x2470000 0x00 0x400>;
+ interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 43 2>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 43 2>;
+ assigned-clock-parents = <&k3_clks 43 3>;
+ power-domains = <&k3_pds 43 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
main_uart0: serial@2800000 {
compatible = "ti,am64-uart", "ti,am654-uart";
reg = <0x00 0x02800000 0x00 0x100>;
@@ -222,6 +406,39 @@
status = "disabled";
};
+ main_spi0: spi@20100000 {
+ compatible = "ti,am654-mcspi", "ti,omap4-mcspi";
+ reg = <0x00 0x20100000 0x00 0x400>;
+ interrupts = <GIC_SPI 172 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&k3_pds 141 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 141 0>;
+ status = "disabled";
+ };
+
+ main_spi1: spi@20110000 {
+ compatible = "ti,am654-mcspi","ti,omap4-mcspi";
+ reg = <0x00 0x20110000 0x00 0x400>;
+ interrupts = <GIC_SPI 173 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&k3_pds 142 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 142 0>;
+ status = "disabled";
+ };
+
+ main_spi2: spi@20120000 {
+ compatible = "ti,am654-mcspi","ti,omap4-mcspi";
+ reg = <0x00 0x20120000 0x00 0x400>;
+ interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&k3_pds 143 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 143 0>;
+ status = "disabled";
+ };
+
main_gpio_intr: interrupt-controller@a00000 {
compatible = "ti,sci-intr";
reg = <0x00 0x00a00000 0x00 0x800>;
@@ -295,4 +512,368 @@
no-1-8-v;
status = "disabled";
};
+
+ usbss0: dwc3-usb@f900000 {
+ compatible = "ti,am62-usb";
+ reg = <0x00 0x0f900000 0x00 0x800>;
+ clocks = <&k3_clks 161 3>;
+ clock-names = "ref";
+ ti,syscon-phy-pll-refclk = <&wkup_conf 0x4008>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ power-domains = <&k3_pds 178 TI_SCI_PD_EXCLUSIVE>;
+ ranges;
+ status = "disabled";
+
+ usb0: usb@31000000 {
+ compatible = "snps,dwc3";
+ reg = <0x00 0x31000000 0x00 0x50000>;
+ interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>, /* irq.0 */
+ <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>; /* irq.0 */
+ interrupt-names = "host", "peripheral";
+ maximum-speed = "high-speed";
+ dr_mode = "otg";
+ };
+ };
+
+ usbss1: dwc3-usb@f910000 {
+ compatible = "ti,am62-usb";
+ reg = <0x00 0x0f910000 0x00 0x800>;
+ clocks = <&k3_clks 162 3>;
+ clock-names = "ref";
+ ti,syscon-phy-pll-refclk = <&wkup_conf 0x4018>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ power-domains = <&k3_pds 179 TI_SCI_PD_EXCLUSIVE>;
+ ranges;
+ status = "disabled";
+
+ usb1: usb@31100000 {
+ compatible = "snps,dwc3";
+ reg = <0x00 0x31100000 0x00 0x50000>;
+ interrupts = <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>, /* irq.0 */
+ <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>; /* irq.0 */
+ interrupt-names = "host", "peripheral";
+ maximum-speed = "high-speed";
+ dr_mode = "otg";
+ };
+ };
+
+ fss: bus@fc00000 {
+ compatible = "simple-bus";
+ reg = <0x00 0x0fc00000 0x00 0x70000>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ status = "disabled";
+
+ ospi0: spi@fc40000 {
+ compatible = "ti,am654-ospi", "cdns,qspi-nor";
+ reg = <0x00 0x0fc40000 0x00 0x100>,
+ <0x05 0x00000000 0x01 0x00000000>;
+ interrupts = <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>;
+ cdns,fifo-depth = <256>;
+ cdns,fifo-width = <4>;
+ cdns,trigger-address = <0x0>;
+ clocks = <&k3_clks 75 7>;
+ assigned-clocks = <&k3_clks 75 7>;
+ assigned-clock-parents = <&k3_clks 75 8>;
+ assigned-clock-rates = <166666666>;
+ power-domains = <&k3_pds 75 TI_SCI_PD_EXCLUSIVE>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+
+ cpsw3g: ethernet@8000000 {
+ compatible = "ti,am642-cpsw-nuss";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ reg = <0x0 0x8000000 0x0 0x200000>;
+ reg-names = "cpsw_nuss";
+ ranges = <0x0 0x0 0x0 0x8000000 0x0 0x200000>;
+ clocks = <&k3_clks 13 0>;
+ assigned-clocks = <&k3_clks 13 3>;
+ assigned-clock-parents = <&k3_clks 13 11>;
+ clock-names = "fck";
+ power-domains = <&k3_pds 13 TI_SCI_PD_EXCLUSIVE>;
+ status = "disabled";
+
+ dmas = <&main_pktdma 0xc600 15>,
+ <&main_pktdma 0xc601 15>,
+ <&main_pktdma 0xc602 15>,
+ <&main_pktdma 0xc603 15>,
+ <&main_pktdma 0xc604 15>,
+ <&main_pktdma 0xc605 15>,
+ <&main_pktdma 0xc606 15>,
+ <&main_pktdma 0xc607 15>,
+ <&main_pktdma 0x4600 15>;
+ dma-names = "tx0", "tx1", "tx2", "tx3", "tx4", "tx5", "tx6",
+ "tx7", "rx";
+
+ ethernet-ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpsw_port1: port@1 {
+ reg = <1>;
+ ti,mac-only;
+ label = "port1";
+ phys = <&phy_gmii_sel 1>;
+ mac-address = [00 00 00 00 00 00];
+ ti,syscon-efuse = <&wkup_conf 0x200>;
+ };
+
+ cpsw_port2: port@2 {
+ reg = <2>;
+ ti,mac-only;
+ label = "port2";
+ phys = <&phy_gmii_sel 2>;
+ mac-address = [00 00 00 00 00 00];
+ };
+ };
+
+ cpsw3g_mdio: mdio@f00 {
+ compatible = "ti,cpsw-mdio","ti,davinci_mdio";
+ reg = <0x0 0xf00 0x0 0x100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&k3_clks 13 0>;
+ clock-names = "fck";
+ bus_freq = <1000000>;
+ };
+
+ cpts@3d000 {
+ compatible = "ti,j721e-cpts";
+ reg = <0x0 0x3d000 0x0 0x400>;
+ clocks = <&k3_clks 13 3>;
+ clock-names = "cpts";
+ interrupts-extended = <&gic500 GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "cpts";
+ ti,cpts-ext-ts-inputs = <4>;
+ ti,cpts-periodic-outputs = <2>;
+ };
+ };
+
+ hwspinlock: spinlock@2a000000 {
+ compatible = "ti,am64-hwspinlock";
+ reg = <0x00 0x2a000000 0x00 0x1000>;
+ #hwlock-cells = <1>;
+ };
+
+ mailbox0_cluster0: mailbox@29000000 {
+ compatible = "ti,am64-mailbox";
+ reg = <0x00 0x29000000 0x00 0x200>;
+ interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
+ #mbox-cells = <1>;
+ ti,mbox-num-users = <4>;
+ ti,mbox-num-fifos = <16>;
+ };
+
+ mailbox0_cluster1: mailbox@29010000 {
+ compatible = "ti,am64-mailbox";
+ reg = <0x00 0x29010000 0x00 0x200>;
+ interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
+ #mbox-cells = <1>;
+ ti,mbox-num-users = <4>;
+ ti,mbox-num-fifos = <16>;
+ };
+
+ mailbox0_cluster2: mailbox@29020000 {
+ compatible = "ti,am64-mailbox";
+ reg = <0x00 0x29020000 0x00 0x200>;
+ interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
+ #mbox-cells = <1>;
+ ti,mbox-num-users = <4>;
+ ti,mbox-num-fifos = <16>;
+ };
+
+ mailbox0_cluster3: mailbox@29030000 {
+ compatible = "ti,am64-mailbox";
+ reg = <0x00 0x29030000 0x00 0x200>;
+ interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
+ #mbox-cells = <1>;
+ ti,mbox-num-users = <4>;
+ ti,mbox-num-fifos = <16>;
+ };
+
+ main_mcan0: can@20701000 {
+ compatible = "bosch,m_can";
+ reg = <0x00 0x20701000 0x00 0x200>,
+ <0x00 0x20708000 0x00 0x8000>;
+ reg-names = "m_can", "message_ram";
+ power-domains = <&k3_pds 98 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 98 6>, <&k3_clks 98 1>;
+ clock-names = "hclk", "cclk";
+ interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "int0", "int1";
+ bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+ status = "disabled";
+ };
+
+ main_rti0: watchdog@e000000 {
+ compatible = "ti,j7-rti-wdt";
+ reg = <0x00 0x0e000000 0x00 0x100>;
+ clocks = <&k3_clks 125 0>;
+ power-domains = <&k3_pds 125 TI_SCI_PD_EXCLUSIVE>;
+ assigned-clocks = <&k3_clks 125 0>;
+ assigned-clock-parents = <&k3_clks 125 2>;
+ };
+
+ main_rti1: watchdog@e010000 {
+ compatible = "ti,j7-rti-wdt";
+ reg = <0x00 0x0e010000 0x00 0x100>;
+ clocks = <&k3_clks 126 0>;
+ power-domains = <&k3_pds 126 TI_SCI_PD_EXCLUSIVE>;
+ assigned-clocks = <&k3_clks 126 0>;
+ assigned-clock-parents = <&k3_clks 126 2>;
+ };
+
+ main_rti2: watchdog@e020000 {
+ compatible = "ti,j7-rti-wdt";
+ reg = <0x00 0x0e020000 0x00 0x100>;
+ clocks = <&k3_clks 127 0>;
+ power-domains = <&k3_pds 127 TI_SCI_PD_EXCLUSIVE>;
+ assigned-clocks = <&k3_clks 127 0>;
+ assigned-clock-parents = <&k3_clks 127 2>;
+ };
+
+ main_rti3: watchdog@e030000 {
+ compatible = "ti,j7-rti-wdt";
+ reg = <0x00 0x0e030000 0x00 0x100>;
+ clocks = <&k3_clks 128 0>;
+ power-domains = <&k3_pds 128 TI_SCI_PD_EXCLUSIVE>;
+ assigned-clocks = <&k3_clks 128 0>;
+ assigned-clock-parents = <&k3_clks 128 2>;
+ };
+
+ main_rti4: watchdog@e040000 {
+ compatible = "ti,j7-rti-wdt";
+ reg = <0x00 0x0e040000 0x00 0x100>;
+ clocks = <&k3_clks 205 0>;
+ power-domains = <&k3_pds 205 TI_SCI_PD_EXCLUSIVE>;
+ assigned-clocks = <&k3_clks 205 0>;
+ assigned-clock-parents = <&k3_clks 205 2>;
+ };
+
+ epwm0: pwm@23000000 {
+ compatible = "ti,am64-epwm", "ti,am3352-ehrpwm";
+ #pwm-cells = <3>;
+ reg = <0x00 0x23000000 0x00 0x100>;
+ power-domains = <&k3_pds 86 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&epwm_tbclk 0>, <&k3_clks 86 0>;
+ clock-names = "tbclk", "fck";
+ status = "disabled";
+ };
+
+ epwm1: pwm@23010000 {
+ compatible = "ti,am64-epwm", "ti,am3352-ehrpwm";
+ #pwm-cells = <3>;
+ reg = <0x00 0x23010000 0x00 0x100>;
+ power-domains = <&k3_pds 87 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&epwm_tbclk 1>, <&k3_clks 87 0>;
+ clock-names = "tbclk", "fck";
+ status = "disabled";
+ };
+
+ epwm2: pwm@23020000 {
+ compatible = "ti,am64-epwm", "ti,am3352-ehrpwm";
+ #pwm-cells = <3>;
+ reg = <0x00 0x23020000 0x00 0x100>;
+ power-domains = <&k3_pds 88 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&epwm_tbclk 2>, <&k3_clks 88 0>;
+ clock-names = "tbclk", "fck";
+ status = "disabled";
+ };
+
+ ecap0: pwm@23100000 {
+ compatible = "ti,am3352-ecap";
+ #pwm-cells = <3>;
+ reg = <0x00 0x23100000 0x00 0x100>;
+ power-domains = <&k3_pds 51 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 51 0>;
+ clock-names = "fck";
+ status = "disabled";
+ };
+
+ ecap1: pwm@23110000 {
+ compatible = "ti,am3352-ecap";
+ #pwm-cells = <3>;
+ reg = <0x00 0x23110000 0x00 0x100>;
+ power-domains = <&k3_pds 52 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 52 0>;
+ clock-names = "fck";
+ status = "disabled";
+ };
+
+ ecap2: pwm@23120000 {
+ compatible = "ti,am3352-ecap";
+ #pwm-cells = <3>;
+ reg = <0x00 0x23120000 0x00 0x100>;
+ power-domains = <&k3_pds 53 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 53 0>;
+ clock-names = "fck";
+ status = "disabled";
+ };
+
+ mcasp0: audio-controller@2b00000 {
+ compatible = "ti,am33xx-mcasp-audio";
+ reg = <0x00 0x02b00000 0x00 0x2000>,
+ <0x00 0x02b08000 0x00 0x400>;
+ reg-names = "mpu", "dat";
+ interrupts = <GIC_SPI 236 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 235 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "tx", "rx";
+
+ dmas = <&main_bcdma 0 0xc500 0>, <&main_bcdma 0 0x4500 0>;
+ dma-names = "tx", "rx";
+
+ clocks = <&k3_clks 190 0>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 190 0>;
+ assigned-clock-parents = <&k3_clks 190 2>;
+ power-domains = <&k3_pds 190 TI_SCI_PD_EXCLUSIVE>;
+ status = "disabled";
+ };
+
+ mcasp1: audio-controller@2b10000 {
+ compatible = "ti,am33xx-mcasp-audio";
+ reg = <0x00 0x02b10000 0x00 0x2000>,
+ <0x00 0x02b18000 0x00 0x400>;
+ reg-names = "mpu", "dat";
+ interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 237 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "tx", "rx";
+
+ dmas = <&main_bcdma 0 0xc501 0>, <&main_bcdma 0 0x4501 0>;
+ dma-names = "tx", "rx";
+
+ clocks = <&k3_clks 191 0>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 191 0>;
+ assigned-clock-parents = <&k3_clks 191 2>;
+ power-domains = <&k3_pds 191 TI_SCI_PD_EXCLUSIVE>;
+ status = "disabled";
+ };
+
+ mcasp2: audio-controller@2b20000 {
+ compatible = "ti,am33xx-mcasp-audio";
+ reg = <0x00 0x02b20000 0x00 0x2000>,
+ <0x00 0x02b28000 0x00 0x400>;
+ reg-names = "mpu", "dat";
+ interrupts = <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 239 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "tx", "rx";
+
+ dmas = <&main_bcdma 0 0xc502 0>, <&main_bcdma 0 0x4502 0>;
+ dma-names = "tx", "rx";
+
+ clocks = <&k3_clks 192 0>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 192 0>;
+ assigned-clock-parents = <&k3_clks 192 2>;
+ power-domains = <&k3_pds 192 TI_SCI_PD_EXCLUSIVE>;
+ status = "disabled";
+ };
};
diff --git a/arch/arm/dts/k3-am62a-mcu.dtsi b/arch/arm/dts/k3-am62a-mcu.dtsi
index 6d1e501b94ab..a6d16a94088c 100644
--- a/arch/arm/dts/k3-am62a-mcu.dtsi
+++ b/arch/arm/dts/k3-am62a-mcu.dtsi
@@ -15,6 +15,51 @@
status = "disabled";
};
+ /*
+ * The MCU domain timer interrupts are routed only to the ESM module,
+ * and not currently available for Linux. The MCU domain timers are
+ * of limited use without interrupts, and likely reserved by the ESM.
+ */
+ mcu_timer0: timer@4800000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x4800000 0x00 0x400>;
+ clocks = <&k3_clks 35 2>;
+ clock-names = "fck";
+ power-domains = <&k3_pds 35 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ status = "reserved";
+ };
+
+ mcu_timer1: timer@4810000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x4810000 0x00 0x400>;
+ clocks = <&k3_clks 48 2>;
+ clock-names = "fck";
+ power-domains = <&k3_pds 48 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ status = "reserved";
+ };
+
+ mcu_timer2: timer@4820000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x4820000 0x00 0x400>;
+ clocks = <&k3_clks 49 2>;
+ clock-names = "fck";
+ power-domains = <&k3_pds 49 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ status = "reserved";
+ };
+
+ mcu_timer3: timer@4830000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x4830000 0x00 0x400>;
+ clocks = <&k3_clks 50 2>;
+ clock-names = "fck";
+ power-domains = <&k3_pds 50 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ status = "reserved";
+ };
+
mcu_uart0: serial@4a00000 {
compatible = "ti,am64-uart", "ti,am654-uart";
reg = <0x00 0x04a00000 0x00 0x100>;
@@ -36,4 +81,90 @@
clock-names = "fck";
status = "disabled";
};
+
+ mcu_spi0: spi@4b00000 {
+ compatible = "ti,am654-mcspi", "ti,omap4-mcspi";
+ reg = <0x00 0x04b00000 0x00 0x400>;
+ interrupts = <GIC_SPI 176 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&k3_pds 147 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 147 0>;
+ status = "disabled";
+ };
+
+ mcu_spi1: spi@4b10000 {
+ compatible = "ti,am654-mcspi","ti,omap4-mcspi";
+ reg = <0x00 0x04b10000 0x00 0x400>;
+ interrupts = <GIC_SPI 177 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&k3_pds 148 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 148 0>;
+ status = "disabled";
+ };
+
+ mcu_gpio_intr: interrupt-controller@4210000 {
+ compatible = "ti,sci-intr";
+ reg = <0x00 0x04210000 0x00 0x200>;
+ ti,intr-trigger-type = <1>;
+ interrupt-controller;
+ interrupt-parent = <&gic500>;
+ #interrupt-cells = <1>;
+ ti,sci = <&dmsc>;
+ ti,sci-dev-id = <5>;
+ ti,interrupt-ranges = <0 104 4>;
+ };
+
+ mcu_gpio0: gpio@4201000 {
+ compatible = "ti,am64-gpio", "ti,keystone-gpio";
+ reg = <0x00 0x04201000 0x00 0x100>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-parent = <&mcu_gpio_intr>;
+ interrupts = <30>, <31>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ ti,ngpio = <24>;
+ ti,davinci-gpio-unbanked = <0>;
+ power-domains = <&k3_pds 79 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 79 0>;
+ clock-names = "gpio";
+ status = "disabled";
+ };
+
+ mcu_rti0: watchdog@4880000 {
+ compatible = "ti,j7-rti-wdt";
+ reg = <0x00 0x04880000 0x00 0x100>;
+ clocks = <&k3_clks 131 0>;
+ power-domains = <&k3_pds 131 TI_SCI_PD_EXCLUSIVE>;
+ assigned-clocks = <&k3_clks 131 0>;
+ assigned-clock-parents = <&k3_clks 131 2>;
+ /* Tightly coupled to M4F */
+ status = "reserved";
+ };
+
+ mcu_mcan0: can@4e08000 {
+ compatible = "bosch,m_can";
+ reg = <0x00 0x4e08000 0x00 0x200>,
+ <0x00 0x4e00000 0x00 0x8000>;
+ reg-names = "m_can", "message_ram";
+ power-domains = <&k3_pds 188 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 188 6>, <&k3_clks 188 1>;
+ clock-names = "hclk", "cclk";
+ bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+ status = "disabled";
+ };
+
+ mcu_mcan1: can@4e18000 {
+ compatible = "bosch,m_can";
+ reg = <0x00 0x4e18000 0x00 0x200>,
+ <0x00 0x4e10000 0x00 0x8000>;
+ reg-names = "m_can", "message_ram";
+ power-domains = <&k3_pds 189 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 189 6>, <&k3_clks 189 1>;
+ clock-names = "hclk", "cclk";
+ bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+ status = "disabled";
+ };
};
diff --git a/arch/arm/dts/k3-am62a-thermal.dtsi b/arch/arm/dts/k3-am62a-thermal.dtsi
new file mode 100644
index 000000000000..85ce545633ea
--- /dev/null
+++ b/arch/arm/dts/k3-am62a-thermal.dtsi
@@ -0,0 +1,47 @@
+// SPDX-License-Identifier: GPL-2.0
+
+#include <dt-bindings/thermal/thermal.h>
+
+thermal_zones: thermal-zones {
+ main0_thermal: main0-thermal {
+ polling-delay-passive = <250>; /* milliSeconds */
+ polling-delay = <500>; /* milliSeconds */
+ thermal-sensors = <&wkup_vtm0 0>;
+
+ trips {
+ main0_crit: main0-crit {
+ temperature = <125000>; /* milliCelsius */
+ hysteresis = <2000>; /* milliCelsius */
+ type = "critical";
+ };
+ };
+ };
+
+ main1_thermal: main1-thermal {
+ polling-delay-passive = <250>; /* milliSeconds */
+ polling-delay = <500>; /* milliSeconds */
+ thermal-sensors = <&wkup_vtm0 1>;
+
+ trips {
+ main1_crit: main1-crit {
+ temperature = <125000>; /* milliCelsius */
+ hysteresis = <2000>; /* milliCelsius */
+ type = "critical";
+ };
+ };
+ };
+
+ main2_thermal: main2-thermal {
+ polling-delay-passive = <250>; /* milliSeconds */
+ polling-delay = <500>; /* milliSeconds */
+ thermal-sensors = <&wkup_vtm0 2>;
+
+ trips {
+ main2_crit: main2-crit {
+ temperature = <125000>; /* milliCelsius */
+ hysteresis = <2000>; /* milliCelsius */
+ type = "critical";
+ };
+ };
+ };
+};
diff --git a/arch/arm/dts/k3-am62a-wakeup.dtsi b/arch/arm/dts/k3-am62a-wakeup.dtsi
index 99afac40e8d4..4e8279fa01e1 100644
--- a/arch/arm/dts/k3-am62a-wakeup.dtsi
+++ b/arch/arm/dts/k3-am62a-wakeup.dtsi
@@ -31,7 +31,7 @@
wkup_i2c0: i2c@2b200000 {
compatible = "ti,am64-i2c", "ti,omap4-i2c";
- reg = <0x00 0x02b200000 0x00 0x100>;
+ reg = <0x00 0x2b200000 0x00 0x100>;
interrupts = <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
@@ -51,4 +51,23 @@
wakeup-source;
status = "disabled";
};
+
+ wkup_rti0: watchdog@2b000000 {
+ compatible = "ti,j7-rti-wdt";
+ reg = <0x00 0x2b000000 0x00 0x100>;
+ clocks = <&k3_clks 132 0>;
+ power-domains = <&k3_pds 132 TI_SCI_PD_EXCLUSIVE>;
+ assigned-clocks = <&k3_clks 132 0>;
+ assigned-clock-parents = <&k3_clks 132 2>;
+ /* Used by DM firmware */
+ status = "reserved";
+ };
+
+ wkup_vtm0: temperature-sensor@b00000 {
+ compatible = "ti,j7200-vtm";
+ reg = <0x00 0xb00000 0x00 0x400>,
+ <0x00 0xb01000 0x00 0x400>;
+ power-domains = <&k3_pds 95 TI_SCI_PD_EXCLUSIVE>;
+ #thermal-sensor-cells = <1>;
+ };
};
diff --git a/arch/arm/dts/k3-am62a.dtsi b/arch/arm/dts/k3-am62a.dtsi
index 6eb87c3f9f3c..61a210ecd5ff 100644
--- a/arch/arm/dts/k3-am62a.dtsi
+++ b/arch/arm/dts/k3-am62a.dtsi
@@ -8,9 +8,10 @@
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/pinctrl/k3.h>
#include <dt-bindings/soc/ti,sci_pm_domain.h>
+#include "k3-pinctrl.h"
+
/ {
model = "Texas Instruments K3 AM62A SoC";
compatible = "ti,am62a7";
@@ -114,6 +115,8 @@
<0x00 0x78100000 0x00 0x78100000 0x00 0x00008000>; /* DM R5 BTCM*/
};
};
+
+ #include "k3-am62a-thermal.dtsi"
};
/* Now include the peripherals for each bus segments */
diff --git a/arch/arm/dts/k3-am62a7-r5-sk.dts b/arch/arm/dts/k3-am62a7-r5-sk.dts
index bbbd9e51d692..bc05dcb5efbe 100644
--- a/arch/arm/dts/k3-am62a7-r5-sk.dts
+++ b/arch/arm/dts/k3-am62a7-r5-sk.dts
@@ -7,7 +7,6 @@
#include "k3-am62a7-sk.dts"
#include "k3-am62a-ddr-1866mhz-32bit.dtsi"
#include "k3-am62a-ddr.dtsi"
-#include "k3-am62a-sk-binman.dtsi"
#include "k3-am62a7-sk-u-boot.dtsi"
@@ -15,33 +14,6 @@
aliases {
remoteproc0 = &sysctrler;
remoteproc1 = &a53_0;
- serial0 = &wkup_uart0;
- serial3 = &main_uart1;
- };
-
- chosen {
- stdout-path = "serial2:115200n8";
- tick-timer = &timer1;
- };
-
- memory@80000000 {
- device_type = "memory";
- /* 4G RAM */
- reg = <0x00000000 0x80000000 0x00000000 0x80000000>,
- <0x00000008 0x80000000 0x00000000 0x80000000>;
- bootph-pre-ram;
- };
-
- reserved-memory {
- #address-cells = <2>;
- #size-cells = <2>;
- ranges;
-
- secure_ddr: optee@9e800000 {
- reg = <0x00 0x9e800000 0x00 0x01800000>; /* for OP-TEE */
- alignment = <0x1000>;
- no-map;
- };
};
a53_0: a53@0 {
@@ -81,67 +53,39 @@
ti,secure-host;
};
-&cbass_main {
- sa3_secproxy: secproxy@44880000 {
- compatible = "ti,am654-secure-proxy";
- #mbox-cells = <1>;
- reg = <0x00 0x44880000 0x00 0x20000>,
- <0x0 0x44860000 0x0 0x20000>,
- <0x0 0x43600000 0x0 0x10000>;
- reg-names = "rt", "scfg", "target_data";
- bootph-pre-ram;
- };
+&secure_proxy_sa3 {
+ /* Needed for initial handshake with ROM */
+ status = "okay";
+ bootph-pre-ram;
+};
+&cbass_main {
sysctrler: sysctrler {
compatible = "ti,am654-system-controller";
mboxes= <&secure_proxy_main 1>,
<&secure_proxy_main 0>,
- <&sa3_secproxy 0>;
+ <&secure_proxy_sa3 0>;
mbox-names = "tx", "rx", "boot_notify";
bootph-pre-ram;
};
};
-&mcu_pmx0 {
- status = "okay";
+&wkup_uart0_pins_default {
bootph-pre-ram;
-
- wkup_uart0_pins_default: wkup-uart0-pins-default {
- pinctrl-single,pins = <
- AM62X_MCU_IOPAD(0x02c, PIN_INPUT, 0) /* (C6) WKUP_UART0_CTSn */
- AM62X_MCU_IOPAD(0x030, PIN_OUTPUT, 0) /* (A4) WKUP_UART0_RTSn */
- AM62X_MCU_IOPAD(0x024, PIN_INPUT, 0) /* (B4) WKUP_UART0_RXD */
- AM62X_MCU_IOPAD(0x028, PIN_OUTPUT, 0) /* (C5) WKUP_UART0_TXD */
- >;
- bootph-pre-ram;
- };
};
-&main_pmx0 {
+&main_uart1_pins_default {
bootph-pre-ram;
- main_uart1_pins_default: main-uart1-pins-default {
- pinctrl-single,pins = <
- AM62X_IOPAD(0x194, PIN_INPUT, 2) /* (B19) MCASP0_AXR3.UART1_CTSn */
- AM62X_IOPAD(0x198, PIN_OUTPUT, 2) /* (A19) MCASP0_AXR2.UART1_RTSn */
- AM62X_IOPAD(0x1ac, PIN_INPUT, 2) /* (E19) MCASP0_AFSR.UART1_RXD */
- AM62X_IOPAD(0x1b0, PIN_OUTPUT, 2) /* (A20) MCASP0_ACLKR.UART1_TXD */
- >;
- bootph-pre-ram;
- };
};
/* WKUP UART0 is used for DM firmware logs */
&wkup_uart0 {
- pinctrl-names = "default";
- pinctrl-0 = <&wkup_uart0_pins_default>;
status = "okay";
bootph-pre-ram;
};
/* Main UART1 is used for TIFS firmware logs */
&main_uart1 {
- pinctrl-names = "default";
- pinctrl-0 = <&main_uart1_pins_default>;
status = "okay";
bootph-pre-ram;
};
diff --git a/arch/arm/dts/k3-am62a7-sk-u-boot.dtsi b/arch/arm/dts/k3-am62a7-sk-u-boot.dtsi
index cf938c43b832..31b89b417483 100644
--- a/arch/arm/dts/k3-am62a7-sk-u-boot.dtsi
+++ b/arch/arm/dts/k3-am62a7-sk-u-boot.dtsi
@@ -4,137 +4,186 @@
* Copyright (C) 2022 Texas Instruments Incorporated - https://www.ti.com/
*/
+#include "k3-am62a-sk-binman.dtsi"
+
/ {
chosen {
stdout-path = "serial2:115200n8";
- tick-timer = &timer1;
+ tick-timer = &main_timer0;
};
memory@80000000 {
- bootph-pre-ram;
+ bootph-all;
};
};
-&cbass_main{
- bootph-pre-ram;
+&main_timer0 {
+ bootph-all;
+};
- timer1: timer@2400000 {
- compatible = "ti,omap5430-timer";
- reg = <0x00 0x2400000 0x00 0x80>;
- ti,timer-alwon;
- clock-frequency = <25000000>;
- bootph-pre-ram;
- };
+&cbass_main {
+ bootph-all;
};
&dmss {
- bootph-pre-ram;
+ bootph-all;
};
&secure_proxy_main {
- bootph-pre-ram;
+ bootph-all;
};
&dmsc {
- bootph-pre-ram;
+ bootph-all;
};
&k3_pds {
- bootph-pre-ram;
+ bootph-all;
};
&k3_clks {
- bootph-pre-ram;
+ bootph-all;
};
&k3_reset {
- bootph-pre-ram;
+ bootph-all;
};
&wkup_conf {
- bootph-pre-ram;
+ bootph-all;
};
&chipid {
- bootph-pre-ram;
+ bootph-all;
};
&main_pmx0 {
- bootph-pre-ram;
+ bootph-all;
};
&main_uart0 {
- bootph-pre-ram;
+ bootph-all;
};
&main_uart0_pins_default {
- bootph-pre-ram;
-};
-
-&main_uart1 {
- bootph-pre-ram;
+ bootph-all;
};
&cbass_mcu {
- bootph-pre-ram;
+ bootph-all;
};
&cbass_wakeup {
- bootph-pre-ram;
+ bootph-all;
};
&mcu_pmx0 {
- bootph-pre-ram;
-};
-
-&wkup_uart0 {
- bootph-pre-ram;
+ bootph-all;
};
&main_gpio0 {
- bootph-pre-ram;
+ bootph-all;
};
&main_i2c0 {
- bootph-pre-ram;
+ bootph-all;
};
&main_i2c0_pins_default {
- bootph-pre-ram;
+ bootph-all;
};
&main_i2c1 {
- bootph-pre-ram;
+ bootph-all;
};
&main_i2c1_pins_default {
- bootph-pre-ram;
+ bootph-all;
};
&exp1 {
- bootph-pre-ram;
+ bootph-all;
};
&sdhci1 {
- bootph-pre-ram;
+ bootph-all;
};
&main_mmc1_pins_default {
- bootph-pre-ram;
+ bootph-all;
};
&k3_reset {
- bootph-pre-ram;
+ bootph-all;
};
&dmsc {
- bootph-pre-ram;
+ bootph-all;
k3_sysreset: sysreset-controller {
compatible = "ti,sci-sysreset";
- bootph-pre-ram;
+ bootph-all;
};
};
&vdd_mmc1 {
- bootph-pre-ram;
+ bootph-all;
+};
+
+&main_bcdma {
+ reg = <0x00 0x485c0100 0x00 0x100>,
+ <0x00 0x4c000000 0x00 0x20000>,
+ <0x00 0x4a820000 0x00 0x20000>,
+ <0x00 0x4aa40000 0x00 0x20000>,
+ <0x00 0x4bc00000 0x00 0x100000>,
+ <0x00 0x48600000 0x00 0x8000>,
+ <0x00 0x484a4000 0x00 0x2000>,
+ <0x00 0x484c2000 0x00 0x2000>;
+ reg-names = "gcfg", "bchanrt", "rchanrt", "tchanrt",
+ "ringrt" , "cfg", "tchan", "rchan";
+ bootph-all;
+};
+
+&main_pktdma {
+ reg = <0x00 0x485c0000 0x00 0x100>,
+ <0x00 0x4a800000 0x00 0x20000>,
+ <0x00 0x4aa00000 0x00 0x20000>,
+ <0x00 0x4b800000 0x00 0x200000>,
+ <0x00 0x485e0000 0x00 0x10000>,
+ <0x00 0x484a0000 0x00 0x2000>,
+ <0x00 0x484c0000 0x00 0x2000>,
+ <0x00 0x48430000 0x00 0x1000>;
+ reg-names = "gcfg", "rchanrt", "tchanrt", "ringrt",
+ "cfg", "tchan", "rchan", "rflow";
+ bootph-all;
+};
+
+&main_mdio1_pins_default {
+ bootph-all;
+};
+
+&cpsw3g_mdio {
+ bootph-all;
+};
+
+&cpsw3g_phy0 {
+ bootph-all;
+};
+
+&main_rgmii1_pins_default {
+ bootph-all;
+};
+
+&phy_gmii_sel {
+ bootph-all;
+};
+
+&cpsw3g {
+ bootph-all;
+ ethernet-ports {
+ bootph-all;
+ };
+};
+
+&cpsw_port1 {
+ bootph-all;
};
diff --git a/arch/arm/dts/k3-am62a7-sk.dts b/arch/arm/dts/k3-am62a7-sk.dts
index 270e669f655a..8f64ac2c7568 100644
--- a/arch/arm/dts/k3-am62a7-sk.dts
+++ b/arch/arm/dts/k3-am62a7-sk.dts
@@ -9,15 +9,17 @@
#include <dt-bindings/leds/common.h>
#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/net/ti-dp83867.h>
#include "k3-am62a7.dtsi"
-#include "k3-am62a-sk-binman.dtsi"
/ {
- compatible = "ti,am62a7-sk", "ti,am62a7";
+ compatible = "ti,am62a7-sk", "ti,am62a7";
model = "Texas Instruments AM62A7 SK";
aliases {
+ serial0 = &wkup_uart0;
serial2 = &main_uart0;
+ serial3 = &main_uart1;
mmc1 = &sdhci1;
};
@@ -77,10 +79,10 @@
regulator-boot-on;
};
- vcc_3v3_sys: regulator-2 {
+ vcc_3v3_main: regulator-2 {
/* output of LM5141-Q1 */
compatible = "regulator-fixed";
- regulator-name = "vcc_3v3_sys";
+ regulator-name = "vcc_3v3_main";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
vin-supply = <&vmain_pd>;
@@ -99,6 +101,17 @@
gpio = <&exp1 3 GPIO_ACTIVE_HIGH>;
};
+ vcc_3v3_sys: regulator-4 {
+ /* output of TPS222965DSGT */
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_3v3_sys";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc_3v3_main>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
@@ -112,38 +125,100 @@
default-state = "off";
};
};
+
+ tlv320_mclk: clk-0 {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <12288000>;
+ };
+
+ codec_audio: sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,name = "AM62Ax-SKEVM";
+ simple-audio-card,widgets =
+ "Headphone", "Headphone Jack",
+ "Line", "Line In",
+ "Microphone", "Microphone Jack";
+ simple-audio-card,routing =
+ "Headphone Jack", "HPLOUT",
+ "Headphone Jack", "HPROUT",
+ "LINE1L", "Line In",
+ "LINE1R", "Line In",
+ "MIC3R", "Microphone Jack",
+ "Microphone Jack", "Mic Bias";
+ simple-audio-card,format = "dsp_b";
+ simple-audio-card,bitclock-master = <&sound_master>;
+ simple-audio-card,frame-master = <&sound_master>;
+ simple-audio-card,bitclock-inversion;
+
+ simple-audio-card,cpu {
+ sound-dai = <&mcasp1>;
+ };
+
+ sound_master: simple-audio-card,codec {
+ sound-dai = <&tlv320aic3106>;
+ clocks = <&tlv320_mclk>;
+ };
+ };
+};
+
+&mcu_pmx0 {
+ wkup_uart0_pins_default: wkup-uart0-default-pins {
+ pinctrl-single,pins = <
+ AM62AX_MCU_IOPAD(0x0024, PIN_INPUT, 0) /* (C9) WKUP_UART0_RXD */
+ AM62AX_MCU_IOPAD(0x0028, PIN_OUTPUT, 0) /* (E9) WKUP_UART0_TXD */
+ AM62AX_MCU_IOPAD(0x002c, PIN_INPUT, 0) /* (C10) WKUP_UART0_CTSn */
+ AM62AX_MCU_IOPAD(0x0030, PIN_OUTPUT, 0) /* (C8) WKUP_UART0_RTSn */
+ >;
+ };
+};
+
+/* WKUP UART0 is used for DM firmware logs */
+&wkup_uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&wkup_uart0_pins_default>;
+ status = "reserved";
};
&main_pmx0 {
- main_uart0_pins_default: main-uart0-pins-default {
+ main_uart0_pins_default: main-uart0-default-pins {
pinctrl-single,pins = <
- AM62AX_IOPAD(0x1c8, PIN_INPUT, 0) /* (D14) UART0_RXD */
- AM62AX_IOPAD(0x1cc, PIN_OUTPUT, 0) /* (E14) UART0_TXD */
+ AM62AX_IOPAD(0x1c8, PIN_INPUT, 0) /* (E14) UART0_RXD */
+ AM62AX_IOPAD(0x1cc, PIN_OUTPUT, 0) /* (D15) UART0_TXD */
>;
};
- main_i2c0_pins_default: main-i2c0-pins-default {
+ main_uart1_pins_default: main-uart1-default-pins {
+ pinctrl-single,pins = <
+ AM62AX_IOPAD(0x01e8, PIN_INPUT, 1) /* (C17) I2C1_SCL.UART1_RXD */
+ AM62AX_IOPAD(0x01ec, PIN_OUTPUT, 1) /* (E17) I2C1_SDA.UART1_TXD */
+ AM62AX_IOPAD(0x0194, PIN_INPUT, 2) /* (C19) MCASP0_AXR3.UART1_CTSn */
+ AM62AX_IOPAD(0x0198, PIN_OUTPUT, 2) /* (B19) MCASP0_AXR2.UART1_RTSn */
+ >;
+ };
+
+ main_i2c0_pins_default: main-i2c0-default-pins {
pinctrl-single,pins = <
AM62AX_IOPAD(0x1e0, PIN_INPUT_PULLUP, 0) /* (B16) I2C0_SCL */
AM62AX_IOPAD(0x1e4, PIN_INPUT_PULLUP, 0) /* (A16) I2C0_SDA */
>;
};
- main_i2c1_pins_default: main-i2c1-pins-default {
+ main_i2c1_pins_default: main-i2c1-default-pins {
pinctrl-single,pins = <
AM62AX_IOPAD(0x1e8, PIN_INPUT_PULLUP, 0) /* (B17) I2C1_SCL */
AM62AX_IOPAD(0x1ec, PIN_INPUT_PULLUP, 0) /* (A17) I2C1_SDA */
>;
};
- main_i2c2_pins_default: main-i2c2-pins-default {
+ main_i2c2_pins_default: main-i2c2-default-pins {
pinctrl-single,pins = <
AM62AX_IOPAD(0x0b0, PIN_INPUT_PULLUP, 1) /* (K22) GPMC0_CSn2.I2C2_SCL */
AM62AX_IOPAD(0x0b4, PIN_INPUT_PULLUP, 1) /* (K24) GPMC0_CSn3.I2C2_SDA */
>;
};
- main_mmc1_pins_default: main-mmc1-pins-default {
+ main_mmc1_pins_default: main-mmc1-default-pins {
pinctrl-single,pins = <
AM62AX_IOPAD(0x23c, PIN_INPUT, 0) /* (A21) MMC1_CMD */
AM62AX_IOPAD(0x234, PIN_INPUT, 0) /* (B22) MMC1_CLK */
@@ -155,11 +230,64 @@
>;
};
- usr_led_pins_default: usr-led-pins-default {
+ usr_led_pins_default: usr-led-default-pins {
pinctrl-single,pins = <
AM62AX_IOPAD(0x244, PIN_OUTPUT, 7) /* (D18) MMC1_SDWP.GPIO1_49 */
>;
};
+
+ main_usb1_pins_default: main-usb1-default-pins {
+ pinctrl-single,pins = <
+ AM62AX_IOPAD(0x0258, PIN_OUTPUT, 0) /* (F18) USB1_DRVVBUS */
+ >;
+ };
+
+ main_mdio1_pins_default: main-mdio1-default-pins {
+ pinctrl-single,pins = <
+ AM62AX_IOPAD(0x160, PIN_OUTPUT, 0) /* (V12) MDIO0_MDC */
+ AM62AX_IOPAD(0x15c, PIN_INPUT, 0) /* (V13) MDIO0_MDIO */
+ >;
+ };
+
+ main_rgmii1_pins_default: main-rgmii1-default-pins {
+ pinctrl-single,pins = <
+ AM62AX_IOPAD(0x14c, PIN_INPUT, 0) /* (AB16) RGMII1_RD0 */
+ AM62AX_IOPAD(0x150, PIN_INPUT, 0) /* (V15) RGMII1_RD1 */
+ AM62AX_IOPAD(0x154, PIN_INPUT, 0) /* (W15) RGMII1_RD2 */
+ AM62AX_IOPAD(0x158, PIN_INPUT, 0) /* (V14) RGMII1_RD3 */
+ AM62AX_IOPAD(0x148, PIN_INPUT, 0) /* (AA16) RGMII1_RXC */
+ AM62AX_IOPAD(0x144, PIN_INPUT, 0) /* (AA15) RGMII1_RX_CTL */
+ AM62AX_IOPAD(0x134, PIN_INPUT, 0) /* (Y17) RGMII1_TD0 */
+ AM62AX_IOPAD(0x138, PIN_INPUT, 0) /* (V16) RGMII1_TD1 */
+ AM62AX_IOPAD(0x13c, PIN_INPUT, 0) /* (Y16) RGMII1_TD2 */
+ AM62AX_IOPAD(0x140, PIN_INPUT, 0) /* (AA17) RGMII1_TD3 */
+ AM62AX_IOPAD(0x130, PIN_INPUT, 0) /* (AB17) RGMII1_TXC */
+ AM62AX_IOPAD(0x12c, PIN_INPUT, 0) /* (W16) RGMII1_TX_CTL */
+ >;
+ };
+
+ main_mcasp1_pins_default: main-mcasp1-default-pins {
+ pinctrl-single,pins = <
+ AM62AX_IOPAD(0x090, PIN_INPUT, 2) /* (L19) GPMC0_BE0n_CLE.MCASP1_ACLKX */
+ AM62AX_IOPAD(0x098, PIN_INPUT, 2) /* (R18) GPMC0_WAIT0.MCASP1_AFSX */
+ AM62AX_IOPAD(0x08c, PIN_OUTPUT, 2) /* (K19) GPMC0_WEn.MCASP1_AXR0 */
+ AM62AX_IOPAD(0x084, PIN_INPUT, 2) /* (L18) GPMC0_ADVn_ALE.MCASP1_AXR2 */
+ >;
+ };
+};
+
+&mcu_pmx0 {
+ status = "okay";
+
+ pmic_irq_pins_default: pmic-irq-default-pins {
+ pinctrl-single,pins = <
+ AM62AX_MCU_IOPAD(0x000, PIN_INPUT, 7) /* (E11) MCU_GPIO0_0 */
+ >;
+ };
+};
+
+&mcu_gpio0 {
+ status = "okay";
};
&main_i2c0 {
@@ -167,13 +295,112 @@
pinctrl-names = "default";
pinctrl-0 = <&main_i2c0_pins_default>;
clock-frequency = <400000>;
+
+ typec_pd0: usb-power-controller@3f {
+ compatible = "ti,tps6598x";
+ reg = <0x3f>;
+
+ connector {
+ compatible = "usb-c-connector";
+ label = "USB-C";
+ self-powered;
+ data-role = "dual";
+ power-role = "sink";
+ port {
+ usb_con_hs: endpoint {
+ remote-endpoint = <&usb0_hs_ep>;
+ };
+ };
+ };
+ };
+
+ tps659312: pmic@48 {
+ compatible = "ti,tps6593-q1";
+ reg = <0x48>;
+ ti,primary-pmic;
+ system-power-controller;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_irq_pins_default>;
+ interrupt-parent = <&mcu_gpio0>;
+ interrupts = <0 IRQ_TYPE_EDGE_FALLING>;
+
+ buck123-supply = <&vcc_3v3_sys>;
+ buck4-supply = <&vcc_3v3_sys>;
+ buck5-supply = <&vcc_3v3_sys>;
+ ldo1-supply = <&vcc_3v3_sys>;
+ ldo2-supply = <&vcc_3v3_sys>;
+ ldo3-supply = <&buck5>;
+ ldo4-supply = <&vcc_3v3_sys>;
+
+ regulators {
+ buck123: buck123 {
+ regulator-name = "vcc_core";
+ regulator-min-microvolt = <715000>;
+ regulator-max-microvolt = <895000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ buck4: buck4 {
+ regulator-name = "vcc_1v1";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ buck5: buck5 {
+ regulator-name = "vcc_1v8_sys";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo1: ldo1 {
+ regulator-name = "vddshv5_sdio";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo2: ldo2 {
+ regulator-name = "vpp_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo3: ldo3 {
+ regulator-name = "vcc_0v85";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <850000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo4: ldo4 {
+ regulator-name = "vdda_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ };
+ };
};
&main_i2c1 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&main_i2c1_pins_default>;
- clock-frequency = <400000>;
+ clock-frequency = <100000>;
exp1: gpio@22 {
compatible = "ti,tca6424";
@@ -194,6 +421,19 @@
"MCASP1_FET_SEL", "UART1_FET_SEL",
"PD_I2C_IRQ", "IO_EXP_TEST_LED";
};
+
+ tlv320aic3106: audio-codec@1b {
+ #sound-dai-cells = <0>;
+ compatible = "ti,tlv320aic3106";
+ reg = <0x1b>;
+ ai3x-micbias-vg = <1>; /* 2.0V */
+
+ /* Regulators */
+ AVDD-supply = <&vcc_3v3_sys>;
+ IOVDD-supply = <&vcc_3v3_sys>;
+ DRVDD-supply = <&vcc_3v3_sys>;
+ DVDD-supply = <&buck5>;
+ };
};
&sdhci1 {
@@ -223,3 +463,84 @@
pinctrl-names = "default";
pinctrl-0 = <&main_uart0_pins_default>;
};
+
+/* Main UART1 is used for TIFS firmware logs */
+&main_uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_uart1_pins_default>;
+ status = "reserved";
+};
+
+&usbss0 {
+ status = "okay";
+ ti,vbus-divider;
+};
+
+&usb0 {
+ usb-role-switch;
+
+ port {
+ usb0_hs_ep: endpoint {
+ remote-endpoint = <&usb_con_hs>;
+ };
+ };
+};
+
+&usbss1 {
+ status = "okay";
+};
+
+&usb1 {
+ dr_mode = "host";
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_usb1_pins_default>;
+};
+
+&cpsw3g {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_rgmii1_pins_default>;
+};
+
+&cpsw_port1 {
+ status = "okay";
+ phy-mode = "rgmii-rxid";
+ phy-handle = <&cpsw3g_phy0>;
+};
+
+&cpsw_port2 {
+ status = "disabled";
+};
+
+&cpsw3g_mdio {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_mdio1_pins_default>;
+
+ cpsw3g_phy0: ethernet-phy@0 {
+ reg = <0>;
+ ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+ ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+ ti,min-output-impedance;
+ };
+};
+
+&mcasp1 {
+ status = "okay";
+ #sound-dai-cells = <0>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_mcasp1_pins_default>;
+
+ op-mode = <0>; /* MCASP_IIS_MODE */
+ tdm-slots = <2>;
+
+ serial-dir = < /* 0: INACTIVE, 1: TX, 2: RX */
+ 1 0 2 0
+ 0 0 0 0
+ 0 0 0 0
+ 0 0 0 0
+ >;
+ tx-num-evt = <32>;
+ rx-num-evt = <32>;
+};
diff --git a/arch/arm/dts/k3-am62a7.dtsi b/arch/arm/dts/k3-am62a7.dtsi
index 331d89fda29d..58f1c43edcf8 100644
--- a/arch/arm/dts/k3-am62a7.dtsi
+++ b/arch/arm/dts/k3-am62a7.dtsi
@@ -95,8 +95,9 @@
L2_0: l2-cache0 {
compatible = "cache";
+ cache-unified;
cache-level = <2>;
- cache-size = <0x40000>;
+ cache-size = <0x80000>;
cache-line-size = <64>;
cache-sets = <512>;
};
--
2.40.0
^ permalink raw reply related [flat|nested] 12+ messages in thread* [PATCH 3/8] dma: ti: k3-udma: Introduce DMA support for the am62ax
2023-11-13 14:51 [PATCH 0/8] arm: dts: am62a: Update to kernel v6.7-rc1 Nishanth Menon
2023-11-13 14:51 ` [PATCH 1/8] arm: mach-k3: am62a: Add main_timer0 id to the dev list Nishanth Menon
2023-11-13 14:51 ` [PATCH 2/8] arm: dts: k3-am62a*: Sync with kernel v6.7-rc1 Nishanth Menon
@ 2023-11-13 14:51 ` Nishanth Menon
2023-11-13 14:51 ` [PATCH 4/8] configs: am62ax_evm_a53_defconfig: Enable networking Nishanth Menon
` (4 subsequent siblings)
7 siblings, 0 replies; 12+ messages in thread
From: Nishanth Menon @ 2023-11-13 14:51 UTC (permalink / raw)
To: Heinrich Schuchardt, Tom Rini
Cc: Siddharth Vadapalli, Andrew Davis, Neha Malcom Francis,
Roger Quadros, Bryan Brattlof, Vignesh Raghavendra, Jai Luthra,
u-boot, Nishanth Menon
From: Vignesh Raghavendra <vigneshr@ti.com>
In preparation for enabling ethernet for the am62ax family of SoCs,
introduce the initial DMA channel settings for the am62ax
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
[bb@ti.com: expanded on commit message]
Signed-off-by: Bryan Brattlof <bb@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
---
NOTE: the patch has a minor checkpatch warning - but, this is inline
with rest of the implementations.
drivers/dma/ti/Makefile | 1 +
drivers/dma/ti/k3-psil-am62a.c | 196 +++++++++++++++++++++++++++++++++
drivers/dma/ti/k3-psil-priv.h | 1 +
drivers/dma/ti/k3-psil.c | 2 +
4 files changed, 200 insertions(+)
create mode 100644 drivers/dma/ti/k3-psil-am62a.c
diff --git a/drivers/dma/ti/Makefile b/drivers/dma/ti/Makefile
index 6807eb8e8b2d..f4e0271efbf3 100644
--- a/drivers/dma/ti/Makefile
+++ b/drivers/dma/ti/Makefile
@@ -8,3 +8,4 @@ k3-psil-data-$(CONFIG_SOC_K3_J721E) += k3-psil-j721e.o
k3-psil-data-$(CONFIG_SOC_K3_J721S2) += k3-psil-j721s2.o
k3-psil-data-$(CONFIG_SOC_K3_AM642) += k3-psil-am64.o
k3-psil-data-$(CONFIG_SOC_K3_AM625) += k3-psil-am62.o
+k3-psil-data-$(CONFIG_SOC_K3_AM62A7) += k3-psil-am62a.o
diff --git a/drivers/dma/ti/k3-psil-am62a.c b/drivers/dma/ti/k3-psil-am62a.c
new file mode 100644
index 000000000000..ca9d71f91422
--- /dev/null
+++ b/drivers/dma/ti/k3-psil-am62a.c
@@ -0,0 +1,196 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2022 Texas Instruments Incorporated - https://www.ti.com
+ */
+
+#include <linux/kernel.h>
+
+#include "k3-psil-priv.h"
+
+#define PSIL_PDMA_XY_TR(x) \
+ { \
+ .thread_id = x, \
+ .ep_config = { \
+ .ep_type = PSIL_EP_PDMA_XY, \
+ .mapped_channel_id = -1, \
+ .default_flow_id = -1, \
+ }, \
+ }
+
+#define PSIL_PDMA_XY_PKT(x) \
+ { \
+ .thread_id = x, \
+ .ep_config = { \
+ .ep_type = PSIL_EP_PDMA_XY, \
+ .mapped_channel_id = -1, \
+ .default_flow_id = -1, \
+ .pkt_mode = 1, \
+ }, \
+ }
+
+#define PSIL_ETHERNET(x, ch, flow_base, flow_cnt) \
+ { \
+ .thread_id = x, \
+ .ep_config = { \
+ .ep_type = PSIL_EP_NATIVE, \
+ .pkt_mode = 1, \
+ .needs_epib = 1, \
+ .psd_size = 16, \
+ .mapped_channel_id = ch, \
+ .flow_start = flow_base, \
+ .flow_num = flow_cnt, \
+ .default_flow_id = flow_base, \
+ }, \
+ }
+
+#define PSIL_SAUL(x, ch, flow_base, flow_cnt, default_flow, tx) \
+ { \
+ .thread_id = x, \
+ .ep_config = { \
+ .ep_type = PSIL_EP_NATIVE, \
+ .pkt_mode = 1, \
+ .needs_epib = 1, \
+ .psd_size = 64, \
+ .mapped_channel_id = ch, \
+ .flow_start = flow_base, \
+ .flow_num = flow_cnt, \
+ .default_flow_id = default_flow, \
+ .notdpkt = tx, \
+ }, \
+ }
+
+#define PSIL_PDMA_MCASP(x) \
+ { \
+ .thread_id = x, \
+ .ep_config = { \
+ .ep_type = PSIL_EP_PDMA_XY, \
+ .pdma_acc32 = 1, \
+ .pdma_burst = 1, \
+ }, \
+ }
+
+#define PSIL_CSI2RX(x) \
+ { \
+ .thread_id = x, \
+ .ep_config = { \
+ .ep_type = PSIL_EP_NATIVE, \
+ }, \
+ }
+
+/* PSI-L source thread IDs, used for RX (DMA_DEV_TO_MEM) */
+static struct psil_ep am62a_src_ep_map[] = {
+ /* SAUL */
+ PSIL_SAUL(0x7504, 20, 35, 8, 35, 0),
+ PSIL_SAUL(0x7505, 21, 35, 8, 36, 0),
+ PSIL_SAUL(0x7506, 22, 43, 8, 43, 0),
+ PSIL_SAUL(0x7507, 23, 43, 8, 44, 0),
+ /* PDMA_MAIN0 - SPI0-3 */
+ PSIL_PDMA_XY_PKT(0x4302),
+ PSIL_PDMA_XY_PKT(0x4303),
+ PSIL_PDMA_XY_PKT(0x4304),
+ PSIL_PDMA_XY_PKT(0x4305),
+ PSIL_PDMA_XY_PKT(0x4306),
+ PSIL_PDMA_XY_PKT(0x4307),
+ PSIL_PDMA_XY_PKT(0x4308),
+ PSIL_PDMA_XY_PKT(0x4309),
+ PSIL_PDMA_XY_PKT(0x430a),
+ PSIL_PDMA_XY_PKT(0x430b),
+ PSIL_PDMA_XY_PKT(0x430c),
+ PSIL_PDMA_XY_PKT(0x430d),
+ /* PDMA_MAIN1 - UART0-6 */
+ PSIL_PDMA_XY_PKT(0x4400),
+ PSIL_PDMA_XY_PKT(0x4401),
+ PSIL_PDMA_XY_PKT(0x4402),
+ PSIL_PDMA_XY_PKT(0x4403),
+ PSIL_PDMA_XY_PKT(0x4404),
+ PSIL_PDMA_XY_PKT(0x4405),
+ PSIL_PDMA_XY_PKT(0x4406),
+ /* PDMA_MAIN2 - MCASP0-2 */
+ PSIL_PDMA_MCASP(0x4500),
+ PSIL_PDMA_MCASP(0x4501),
+ PSIL_PDMA_MCASP(0x4502),
+ /* CPSW3G */
+ PSIL_ETHERNET(0x4600, 19, 19, 16),
+ /* CSI2RX */
+ PSIL_CSI2RX(0x5000),
+ PSIL_CSI2RX(0x5001),
+ PSIL_CSI2RX(0x5002),
+ PSIL_CSI2RX(0x5003),
+ PSIL_CSI2RX(0x5004),
+ PSIL_CSI2RX(0x5005),
+ PSIL_CSI2RX(0x5006),
+ PSIL_CSI2RX(0x5007),
+ PSIL_CSI2RX(0x5008),
+ PSIL_CSI2RX(0x5009),
+ PSIL_CSI2RX(0x500a),
+ PSIL_CSI2RX(0x500b),
+ PSIL_CSI2RX(0x500c),
+ PSIL_CSI2RX(0x500d),
+ PSIL_CSI2RX(0x500e),
+ PSIL_CSI2RX(0x500f),
+ PSIL_CSI2RX(0x5010),
+ PSIL_CSI2RX(0x5011),
+ PSIL_CSI2RX(0x5012),
+ PSIL_CSI2RX(0x5013),
+ PSIL_CSI2RX(0x5014),
+ PSIL_CSI2RX(0x5015),
+ PSIL_CSI2RX(0x5016),
+ PSIL_CSI2RX(0x5017),
+ PSIL_CSI2RX(0x5018),
+ PSIL_CSI2RX(0x5019),
+ PSIL_CSI2RX(0x501a),
+ PSIL_CSI2RX(0x501b),
+ PSIL_CSI2RX(0x501c),
+ PSIL_CSI2RX(0x501d),
+ PSIL_CSI2RX(0x501e),
+ PSIL_CSI2RX(0x501f),
+};
+
+/* PSI-L destination thread IDs, used for TX (DMA_MEM_TO_DEV) */
+static struct psil_ep am62a_dst_ep_map[] = {
+ /* SAUL */
+ PSIL_SAUL(0xf500, 27, 83, 8, 83, 1),
+ PSIL_SAUL(0xf501, 28, 91, 8, 91, 1),
+ /* PDMA_MAIN0 - SPI0-3 */
+ PSIL_PDMA_XY_PKT(0xc302),
+ PSIL_PDMA_XY_PKT(0xc303),
+ PSIL_PDMA_XY_PKT(0xc304),
+ PSIL_PDMA_XY_PKT(0xc305),
+ PSIL_PDMA_XY_PKT(0xc306),
+ PSIL_PDMA_XY_PKT(0xc307),
+ PSIL_PDMA_XY_PKT(0xc308),
+ PSIL_PDMA_XY_PKT(0xc309),
+ PSIL_PDMA_XY_PKT(0xc30a),
+ PSIL_PDMA_XY_PKT(0xc30b),
+ PSIL_PDMA_XY_PKT(0xc30c),
+ PSIL_PDMA_XY_PKT(0xc30d),
+ /* PDMA_MAIN1 - UART0-6 */
+ PSIL_PDMA_XY_PKT(0xc400),
+ PSIL_PDMA_XY_PKT(0xc401),
+ PSIL_PDMA_XY_PKT(0xc402),
+ PSIL_PDMA_XY_PKT(0xc403),
+ PSIL_PDMA_XY_PKT(0xc404),
+ PSIL_PDMA_XY_PKT(0xc405),
+ PSIL_PDMA_XY_PKT(0xc406),
+ /* PDMA_MAIN2 - MCASP0-2 */
+ PSIL_PDMA_MCASP(0xc500),
+ PSIL_PDMA_MCASP(0xc501),
+ PSIL_PDMA_MCASP(0xc502),
+ /* CPSW3G */
+ PSIL_ETHERNET(0xc600, 19, 19, 8),
+ PSIL_ETHERNET(0xc601, 20, 27, 8),
+ PSIL_ETHERNET(0xc602, 21, 35, 8),
+ PSIL_ETHERNET(0xc603, 22, 43, 8),
+ PSIL_ETHERNET(0xc604, 23, 51, 8),
+ PSIL_ETHERNET(0xc605, 24, 59, 8),
+ PSIL_ETHERNET(0xc606, 25, 67, 8),
+ PSIL_ETHERNET(0xc607, 26, 75, 8),
+};
+
+struct psil_ep_map am62a_ep_map = {
+ .name = "am62a",
+ .src = am62a_src_ep_map,
+ .src_count = ARRAY_SIZE(am62a_src_ep_map),
+ .dst = am62a_dst_ep_map,
+ .dst_count = ARRAY_SIZE(am62a_dst_ep_map),
+};
diff --git a/drivers/dma/ti/k3-psil-priv.h b/drivers/dma/ti/k3-psil-priv.h
index 563bc57e2060..83f873b84ceb 100644
--- a/drivers/dma/ti/k3-psil-priv.h
+++ b/drivers/dma/ti/k3-psil-priv.h
@@ -42,5 +42,6 @@ extern struct psil_ep_map j721e_ep_map;
extern struct psil_ep_map j721s2_ep_map;
extern struct psil_ep_map am64_ep_map;
extern struct psil_ep_map am62_ep_map;
+extern struct psil_ep_map am62a_ep_map;
#endif /* K3_PSIL_PRIV_H_ */
diff --git a/drivers/dma/ti/k3-psil.c b/drivers/dma/ti/k3-psil.c
index 963321aa1e34..d4d4fede8fa1 100644
--- a/drivers/dma/ti/k3-psil.c
+++ b/drivers/dma/ti/k3-psil.c
@@ -26,6 +26,8 @@ struct psil_endpoint_config *psil_get_ep_config(u32 thread_id)
soc_ep_map = &am64_ep_map;
else if (IS_ENABLED(CONFIG_SOC_K3_AM625))
soc_ep_map = &am62_ep_map;
+ else if (IS_ENABLED(CONFIG_SOC_K3_AM62A7))
+ soc_ep_map = &am62a_ep_map;
}
if (thread_id & K3_PSIL_DST_THREAD_ID_OFFSET && soc_ep_map->dst) {
--
2.40.0
^ permalink raw reply related [flat|nested] 12+ messages in thread