[U-Boot-Users] is there any other toolchains for u-boot of mips arch?

[U-Boot-Users] is there any other toolchains for u-boot of mips arch?

[zhuzhenhua]

to use other toolchain?
what need to do?
i change the CROSS_COMPILE in Makefile
and output the bin directory of the new toolchain
and only get the error likes that
/bin/sh: line 1: mips-linux-as : command not found


regards
       zhuzhenhua

[U-Boot-Users] is there any other toolchains for u-boot of mips arch?

[Grant Likely]

zhuzhenhua wrote:
> to use other toolchain?
> what need to do?
> i change the CROSS_COMPILE in Makefile
> and output the bin directory of the new toolchain
> and only get the error likes that
> /bin/sh: line 1: mips-linux-as : command not found
make sure mips-linux-as is in your path

$ export PATH=/path/to/mips-linux-as/bin:$PATH
$ make

[U-Boot-Users] is there any other toolchains for u-boot of mips arch?

[Grant Likely]

Some quick etiquette points if your going to use the mailing list:
1. Put your replies *below* what your replying to, not above.
2. Always CC the mailing list on replies
3. Don't just describe what you saw; attach logs also.

zhuzhenhua wrote:
> i do not get clear about it
> $ export PATH=/path/to/mips-linux-as/bin:$PATH
> 
> /path/to/mips-linux-as/bin is what path?
If mips-linux-as is in the path /opt/mips-linux/bin, then:
$ export PATH=/opt/mips-linux/bin:$PATH

Basically, your tools should be in your path so you can run the tools
from the command line like this:
$ mips-linux-as

> 
> do you mean change my toolchain dir name to mips-linux-as?
I think your confused.  What is the full path of your cross compiler?

Here's an example:
My cross toolchain is: powerpc-linux
It lives in: /opt/powerpc-linux
The path to the cross gcc is: /opt/powerpc-linux/bin/powerpc-linux-gcc

Therefore I set in my environment:
$ PATH=/opt/powerpc-linux/bin:$PATH
$ CROSS_COMPILE=powerpc-linux-
$ export PATH CROSS_COMPILE

[U-Boot-Users] is there any other toolchains for u-boot of mips arch?

[Wolfgang Denk]

In message <50c9a2250511221728o44c2c318ia2c347fa658ee548@mail.gmail.com> you wrote:
> to use other toolchain?
> what need to do?
> i change the CROSS_COMPILE in Makefile

No, you do NOT change the Makefile.  You  just  set  and  export  the
CROSS_COMPILE variable in your shell environmnt.

> and output the bin directory of the new toolchain
> and only get the error likes that
> /bin/sh: line 1: mips-linux-as : command not found

Maybe there is a problem with your toolchain?

Best regards,

Wolfgang Denk

-- 
Software Engineering:  Embedded and Realtime Systems,  Embedded Linux
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
The IQ of the group is the lowest IQ of a member of the group divided
by the number of people in the group.

[U-Boot-Users] is there any other toolchains for u-boot of mips arch?

[Anders Larsen]

Grant Likely <grant.likely@secretlab.ca> schrieb am Mittwoch, 23. November 2005 um 06:45 +0100:
>Some quick etiquette points if your going to use the mailing list:
>1. Put your replies *below* what your replying to, not above.
>2. Always CC the mailing list on replies
>3. Don't just describe what you saw; attach logs also.

4. Keep the Subject: shorter and write your question in the
   _body_ of the e-mail.

Cheers
 Anders