[U-Boot-Users] eth0 not geting enabled

[U-Boot-Users] eth0 not geting enabled

[Avinash Vijayvergia]

>> Hi there
>>
>> I am working on at91sam9260ek. I have put kernel and rfs on dataflash. 
> >Now this board boots up but doesn't enable eth0. I searched net and 
> >found that if I do a ping it enables phy (MD9161A). But if I do that 
> >when there is no network u-boot never recovers. Can someone tell me 
> >the way out. It is successful when network is available, though.

>What do you mean by 'u-boot never recovers'?  It should time out if you 
>try a network operation and are not connected to anything useful.

I expected the same but it doesn't timeout. It just keeps tryingand I have to reset.

regards
Avinash



      
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.denx.de/pipermail/u-boot/attachments/20080602/f1cb64e4/attachment.htm 

[U-Boot-Users] eth0 not geting enabled

[Avinash Vijayvergia]

> Hi there
<snip>

>>  But if I do that when there is no network u-boot never recovers. Can someone tell       > me the way out. It is successful when network is available, >>though.

>Are you using a old (really old) u-boot. This behaviour was observed
>on u-boot 1.1.2, but when we upgraded to 1.2.0 and above, ping used to
>timeout.

I have tried u-boot 1.1.5 and 1.3.0. They both don't timeout.

--Avinash


      
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.denx.de/pipermail/u-boot/attachments/20080603/d7ac59bf/attachment.htm 

[U-Boot-Users] eth0 not geting enabled

[Avinash Vijayvergia]

Hi there


I am working on at91sam9260ek. I have put kernel and rfs on dataflash. Now this board boots up but doesn't enable eth0. I searched net and found that if I do a ping it enables phy (MD9161A). But if I do that when there is no network u-boot never recovers. Can someone tell me the way out. It is successful when network is available, though.

Thanks
Avinash


      
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.denx.de/pipermail/u-boot/attachments/20080602/4426f662/attachment.htm 

[U-Boot-Users] eth0 not geting enabled

[Ben Warren]

Avinash Vijayvergia wrote:
> Hi there
>
> I am working on at91sam9260ek. I have put kernel and rfs on dataflash. 
> Now this board boots up but doesn't enable eth0. I searched net and 
> found that if I do a ping it enables phy (MD9161A). But if I do that 
> when there is no network u-boot never recovers. Can someone tell me 
> the way out. It is successful when network is available, though.
What do you mean by 'u-boot never recovers'?  It should time out if you 
try a network operation and are not connected to anything useful.

regards,
Ben

[U-Boot-Users] eth0 not geting enabled

[sughosh ganu]

Hi,

On Mon, Jun 2, 2008 at 1:21 PM, Avinash Vijayvergia
<avinashs36@yahoo.com> wrote:
> Hi there
 <snip>

>  But if I do that when there is no network u-boot never recovers. Can someone tell       > me the way out. It is successful when network is available, though.

Are you using a old (really old) u-boot. This behaviour was observed
on u-boot 1.1.2, but when we upgraded to 1.2.0 and above, ping used to
timeout.

--
sughosh

[U-Boot-Users] eth0 not geting enabled

[Avinash Vijayvergia]

Hi there

I am working on at91sam9260ek. I have put kernel and rfs on dataflash. Now this board boots up but doesn't enable eth0. I searched net and found that if I do a ping it enables phy (MD9161A). But if I do that when there is no network u-boot never recovers. Can someone tell me the way out.

Thanks
Avinash



      
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.denx.de/pipermail/u-boot/attachments/20080530/a8ea27ab/attachment.htm