U-Boot Archive on lore.kernel.org
 help / color / mirror / Atom feed
* [U-Boot] [PATCH v2] spi: soft_spi: Fix for soft_spi
@ 2019-01-07  8:20 Horatiu Vultur
  2019-01-07  8:20 ` Horatiu Vultur
  2019-01-07  8:20 ` [U-Boot] [PATCH v2] spi: soft_spi: Fix null ptr when probing soft_spi Horatiu Vultur
  0 siblings, 2 replies; 5+ messages in thread
From: Horatiu Vultur @ 2019-01-07  8:20 UTC (permalink / raw)
  To: u-boot

This patch series, fix a null ptr inside soft_spi.

This version address comments from Jagan Teki
<jagan@amarulasolutions.com>

v2 changes:
 - update soft_spi_platdata inside .set_mode.


Horatiu Vultur (1):
  spi: soft_spi: Fix null ptr when probing soft_spi.

 drivers/spi/soft_spi.c | 15 ++++++++-------
 1 file changed, 8 insertions(+), 7 deletions(-)

-- 
2.7.4

^ permalink raw reply	[flat|nested] 5+ messages in thread

* [U-Boot] [PATCH v2] spi: soft_spi: Fix for soft_spi
  2019-01-07  8:20 [U-Boot] [PATCH v2] spi: soft_spi: Fix for soft_spi Horatiu Vultur
@ 2019-01-07  8:20 ` Horatiu Vultur
  2019-01-07  8:20 ` [U-Boot] [PATCH v2] spi: soft_spi: Fix null ptr when probing soft_spi Horatiu Vultur
  1 sibling, 0 replies; 5+ messages in thread
From: Horatiu Vultur @ 2019-01-07  8:20 UTC (permalink / raw)
  To: u-boot

This patch series, fix a null ptr inside soft_spi.

This version address comments from Jagan Teki
<jagan@amarulasolutions.com>

v2 changes:
 - update soft_spi_platdata inside .set_mode.

Horatiu Vultur (1):
  spi: soft_spi: Fix null ptr when probing soft_spi.

 drivers/spi/soft_spi.c | 15 ++++++++-------
 1 file changed, 8 insertions(+), 7 deletions(-)

-- 
2.7.4

^ permalink raw reply	[flat|nested] 5+ messages in thread

* [U-Boot] [PATCH v2] spi: soft_spi: Fix null ptr when probing soft_spi.
  2019-01-07  8:20 [U-Boot] [PATCH v2] spi: soft_spi: Fix for soft_spi Horatiu Vultur
  2019-01-07  8:20 ` Horatiu Vultur
@ 2019-01-07  8:20 ` Horatiu Vultur
  2019-01-07 17:09   ` Daniel Schwierzeck
  1 sibling, 1 reply; 5+ messages in thread
From: Horatiu Vultur @ 2019-01-07  8:20 UTC (permalink / raw)
  To: u-boot

When probing soft_spi the result of dev_get_parent_priv(dev) in probe
function is null ptr because the spi is on the ahb bus which has
per_child_auto_alloc_size set to 0. Therefore it would generate an Ooops
messages when accessing spi_slave structure.

The fix consist of updating the soft_spi_platdata flags inside the
.set_mode.

Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
---
 drivers/spi/soft_spi.c | 15 ++++++++-------
 1 file changed, 8 insertions(+), 7 deletions(-)

diff --git a/drivers/spi/soft_spi.c b/drivers/spi/soft_spi.c
index b06883f..2c47577 100644
--- a/drivers/spi/soft_spi.c
+++ b/drivers/spi/soft_spi.c
@@ -183,9 +183,15 @@ static int soft_spi_set_speed(struct udevice *dev, unsigned int speed)
 static int soft_spi_set_mode(struct udevice *dev, unsigned int mode)
 {
 	struct soft_spi_priv *priv = dev_get_priv(dev);
+	struct soft_spi_platdata *plat = dev->platdata;
 
 	priv->mode = mode;
 
+	if (!(mode & SPI_CS_HIGH))
+		plat->cs.flags |= GPIOD_ACTIVE_LOW;
+	if (mode & SPI_CPOL)
+		plat->sclk.flags |= GPIOD_ACTIVE_LOW;
+
 	return 0;
 }
 
@@ -210,18 +216,13 @@ static int soft_spi_ofdata_to_platdata(struct udevice *dev)
 
 static int soft_spi_probe(struct udevice *dev)
 {
-	struct spi_slave *slave = dev_get_parent_priv(dev);
 	struct soft_spi_platdata *plat = dev->platdata;
-	int cs_flags, clk_flags;
 	int ret;
 
-	cs_flags = (slave->mode & SPI_CS_HIGH) ? 0 : GPIOD_ACTIVE_LOW;
-	clk_flags = (slave->mode & SPI_CPOL) ? GPIOD_ACTIVE_LOW : 0;
-
 	if (gpio_request_by_name(dev, "cs-gpios", 0, &plat->cs,
-				 GPIOD_IS_OUT | cs_flags) ||
+				 GPIOD_IS_OUT) ||
 	    gpio_request_by_name(dev, "gpio-sck", 0, &plat->sclk,
-				 GPIOD_IS_OUT | clk_flags))
+				 GPIOD_IS_OUT))
 		return -EINVAL;
 
 	ret = gpio_request_by_name(dev, "gpio-mosi", 0, &plat->mosi,
-- 
2.7.4

^ permalink raw reply related	[flat|nested] 5+ messages in thread

* [U-Boot] [PATCH v2] spi: soft_spi: Fix null ptr when probing soft_spi.
  2019-01-07  8:20 ` [U-Boot] [PATCH v2] spi: soft_spi: Fix null ptr when probing soft_spi Horatiu Vultur
@ 2019-01-07 17:09   ` Daniel Schwierzeck
  2019-01-07 19:29     ` Horatiu Vultur
  0 siblings, 1 reply; 5+ messages in thread
From: Daniel Schwierzeck @ 2019-01-07 17:09 UTC (permalink / raw)
  To: u-boot



Am 07.01.19 um 09:20 schrieb Horatiu Vultur:
> When probing soft_spi the result of dev_get_parent_priv(dev) in probe
> function is null ptr because the spi is on the ahb bus which has
> per_child_auto_alloc_size set to 0. Therefore it would generate an Ooops
> messages when accessing spi_slave structure.
> 
> The fix consist of updating the soft_spi_platdata flags inside the
> .set_mode.
> 
> Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
> ---
>  drivers/spi/soft_spi.c | 15 ++++++++-------
>  1 file changed, 8 insertions(+), 7 deletions(-)

is this patch still required with https://patchwork.ozlabs.org/cover/1021335/ ?

> 
> diff --git a/drivers/spi/soft_spi.c b/drivers/spi/soft_spi.c
> index b06883f..2c47577 100644
> --- a/drivers/spi/soft_spi.c
> +++ b/drivers/spi/soft_spi.c
> @@ -183,9 +183,15 @@ static int soft_spi_set_speed(struct udevice *dev, unsigned int speed)
>  static int soft_spi_set_mode(struct udevice *dev, unsigned int mode)
>  {
>  	struct soft_spi_priv *priv = dev_get_priv(dev);
> +	struct soft_spi_platdata *plat = dev->platdata;
>  
>  	priv->mode = mode;
>  
> +	if (!(mode & SPI_CS_HIGH))
> +		plat->cs.flags |= GPIOD_ACTIVE_LOW;
> +	if (mode & SPI_CPOL)
> +		plat->sclk.flags |= GPIOD_ACTIVE_LOW;
> +

don't you need to manually set the initial state of CS and CLK now? This was previously done by
gpio_request_by_name(). That's why the driver needed to know the low-active bits early.

>  	return 0;
>  }
>  
> @@ -210,18 +216,13 @@ static int soft_spi_ofdata_to_platdata(struct udevice *dev)
>  
>  static int soft_spi_probe(struct udevice *dev)
>  {
> -	struct spi_slave *slave = dev_get_parent_priv(dev);
>  	struct soft_spi_platdata *plat = dev->platdata;
> -	int cs_flags, clk_flags;
>  	int ret;
>  
> -	cs_flags = (slave->mode & SPI_CS_HIGH) ? 0 : GPIOD_ACTIVE_LOW;
> -	clk_flags = (slave->mode & SPI_CPOL) ? GPIOD_ACTIVE_LOW : 0;
> -
>  	if (gpio_request_by_name(dev, "cs-gpios", 0, &plat->cs,
> -				 GPIOD_IS_OUT | cs_flags) ||
> +				 GPIOD_IS_OUT) ||
>  	    gpio_request_by_name(dev, "gpio-sck", 0, &plat->sclk,
> -				 GPIOD_IS_OUT | clk_flags))
> +				 GPIOD_IS_OUT))
>  		return -EINVAL;
>  
>  	ret = gpio_request_by_name(dev, "gpio-mosi", 0, &plat->mosi,
> 

-- 
- Daniel

^ permalink raw reply	[flat|nested] 5+ messages in thread

* [U-Boot] [PATCH v2] spi: soft_spi: Fix null ptr when probing soft_spi.
  2019-01-07 17:09   ` Daniel Schwierzeck
@ 2019-01-07 19:29     ` Horatiu Vultur
  0 siblings, 0 replies; 5+ messages in thread
From: Horatiu Vultur @ 2019-01-07 19:29 UTC (permalink / raw)
  To: u-boot

The 01/07/2019 18:09, Daniel Schwierzeck wrote:
> 
> 
> Am 07.01.19 um 09:20 schrieb Horatiu Vultur:
> > When probing soft_spi the result of dev_get_parent_priv(dev) in probe
> > function is null ptr because the spi is on the ahb bus which has
> > per_child_auto_alloc_size set to 0. Therefore it would generate an Ooops
> > messages when accessing spi_slave structure.
> > 
> > The fix consist of updating the soft_spi_platdata flags inside the
> > .set_mode.
> > 
> > Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
> > ---
> >  drivers/spi/soft_spi.c | 15 ++++++++-------
> >  1 file changed, 8 insertions(+), 7 deletions(-)
> 
> is this patch still required with https://patchwork.ozlabs.org/cover/1021335/ ?

This patch is not required if you will take in
https://patchwork.ozlabs.org/cover/1021335.

> 
> > 
> > diff --git a/drivers/spi/soft_spi.c b/drivers/spi/soft_spi.c
> > index b06883f..2c47577 100644
> > --- a/drivers/spi/soft_spi.c
> > +++ b/drivers/spi/soft_spi.c
> > @@ -183,9 +183,15 @@ static int soft_spi_set_speed(struct udevice *dev, unsigned int speed)
> >  static int soft_spi_set_mode(struct udevice *dev, unsigned int mode)
> >  {
> >  	struct soft_spi_priv *priv = dev_get_priv(dev);
> > +	struct soft_spi_platdata *plat = dev->platdata;
> >  
> >  	priv->mode = mode;
> >  
> > +	if (!(mode & SPI_CS_HIGH))
> > +		plat->cs.flags |= GPIOD_ACTIVE_LOW;
> > +	if (mode & SPI_CPOL)
> > +		plat->sclk.flags |= GPIOD_ACTIVE_LOW;
> > +
> 
> don't you need to manually set the initial state of CS and CLK now? This was previously done by
> gpio_request_by_name(). That's why the driver needed to know the low-active bits early.

No, because it is still using gpio_request_by_name() and that one will
set the initial values for CS and CLK. And now in the .set_mode() we
just update the CS and CLK, which is called before probing the spi.

> 
> >  	return 0;
> >  }
> >  
> > @@ -210,18 +216,13 @@ static int soft_spi_ofdata_to_platdata(struct udevice *dev)
> >  
> >  static int soft_spi_probe(struct udevice *dev)
> >  {
> > -	struct spi_slave *slave = dev_get_parent_priv(dev);
> >  	struct soft_spi_platdata *plat = dev->platdata;
> > -	int cs_flags, clk_flags;
> >  	int ret;
> >  
> > -	cs_flags = (slave->mode & SPI_CS_HIGH) ? 0 : GPIOD_ACTIVE_LOW;
> > -	clk_flags = (slave->mode & SPI_CPOL) ? GPIOD_ACTIVE_LOW : 0;
> > -
> >  	if (gpio_request_by_name(dev, "cs-gpios", 0, &plat->cs,
> > -				 GPIOD_IS_OUT | cs_flags) ||
> > +				 GPIOD_IS_OUT) ||
> >  	    gpio_request_by_name(dev, "gpio-sck", 0, &plat->sclk,
> > -				 GPIOD_IS_OUT | clk_flags))
> > +				 GPIOD_IS_OUT))
> >  		return -EINVAL;
> >  
> >  	ret = gpio_request_by_name(dev, "gpio-mosi", 0, &plat->mosi,
> > 
> 
> -- 
> - Daniel

-- 
/Horatiu

^ permalink raw reply	[flat|nested] 5+ messages in thread

end of thread, other threads:[~2019-01-07 19:29 UTC | newest]

Thread overview: 5+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2019-01-07  8:20 [U-Boot] [PATCH v2] spi: soft_spi: Fix for soft_spi Horatiu Vultur
2019-01-07  8:20 ` Horatiu Vultur
2019-01-07  8:20 ` [U-Boot] [PATCH v2] spi: soft_spi: Fix null ptr when probing soft_spi Horatiu Vultur
2019-01-07 17:09   ` Daniel Schwierzeck
2019-01-07 19:29     ` Horatiu Vultur

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox