From: "Brian & Chamaigne Scamman" <scammanbc@earthlink.net>
To: 'Tejun Heo' <htejun@gmail.com>
Cc: 'Mark Lord' <liml@rtr.ca>, jeff@garzik.org, linux-ide@vger.kernel.org
Subject: RE: [PATCHSET #upstream-fixes] git tree available
Date: Wed, 21 May 2008 15:42:23 -0400 [thread overview]
Message-ID: <00b901c8bb7a$caaa1ed0$6917a8c0@parents> (raw)
In-Reply-To: <4833AC14.5090207@gmail.com>
[-- Attachment #1: Type: text/plain, Size: 776 bytes --]
Tejun Heo wrote:
>Brian & Chamaigne Scamman wrote:
>> One remaining issue is the "failed to IDENTIFY (I/O error, err
mask=0xll)"
>> message. If the PMP, bridges and drives are powered up before I
>> insert the eSATA cable in to the controller, I don't receive the
>> message. The message appears when only when I have the eSATA cable
>> attached to the controller and then simultaneously power on the PMP
>> and drives. In the attached dmesg log, the drive is eventually
>> recognized; however there have been a couple of times when the drives
>> aren't recognized. An eSATA cable remove/re-insert fixes the problem.
>
>Hmm... can you please post the failing log?
Here's a dmesg log where one of the drives is never recognized, but the
others eventually are...
-Brian
[-- Attachment #2: pmp_drive_header_err.txt --]
[-- Type: text/plain, Size: 6104 bytes --]
ata3: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0xe frozen
ata3: irq_stat 0x00b40090, PHY RDY changed
ata3: hard resetting link
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata3.15: Port Multiplier 1.1, 0x1095:0x3726 r23, 6 ports, feat 0x1/0x9
ata3.00: hard resetting link
ata3.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata3.01: hard resetting link
ata3.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.02: hard resetting link
ata3.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.03: hard resetting link
ata3.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.04: hard resetting link
ata3.04: SATA link down (SStatus 0 SControl 320)
ata3.05: hard resetting link
ata3.05: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata3.00: failed to IDENTIFY (I/O error, err_mask=0x11)
ata3.15: hard resetting link
ata3.15: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata3.00: hard resetting link
ata3.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata3.01: hard resetting link
ata3.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.02: hard resetting link
ata3.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.03: hard resetting link
ata3.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.05: hard resetting link
ata3.05: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata3.00: ATA-6: Super Talent Tech, Rev 2.11, max UDMA/133
ata3.00: 127923200 sectors, multi 1: LBA
ata3.00: applying bridge limits
ata3.00: configured for UDMA/100
ata3.01: ATA-6: Super Talent Tech, Rev 2.11, max UDMA/133
ata3.01: 127923200 sectors, multi 1: LBA
ata3.01: applying bridge limits
ata3.01: configured for UDMA/100
ata3.02: ATA-6: Super Talent Tech, Rev 2.11, max UDMA/133
ata3.02: 127923200 sectors, multi 1: LBA
ata3.02: applying bridge limits
ata3.02: configured for UDMA/100
ata3.03: failed to IDENTIFY (I/O error, err_mask=0x11)
ata3.15: hard resetting link
ata3.15: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata3.00: hard resetting link
ata3.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata3.01: hard resetting link
ata3.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.02: hard resetting link
ata3.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.03: hard resetting link
ata3.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.04: hard resetting link
ata3.04: SATA link down (SStatus 0 SControl 320)
ata3.05: hard resetting link
ata3.05: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata3.00: configured for UDMA/100
ata3.01: configured for UDMA/100
ata3.02: configured for UDMA/100
ata3.03: failed to IDENTIFY (I/O error, err_mask=0x11)
ata3.15: hard resetting link
ata3.15: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata3.00: hard resetting link
ata3.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata3.01: hard resetting link
ata3.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.02: hard resetting link
ata3.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.03: hard resetting link
ata3.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.05: hard resetting link
ata3.05: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata3.00: configured for UDMA/100
ata3.01: configured for UDMA/100
ata3.02: configured for UDMA/100
ata3.03: failed to IDENTIFY (I/O error, err_mask=0x11)
ata3.03: failed to recover link after 3 tries, disabling
ata3: failed to recover PMP, retrying in 5 secs
ata3.15: hard resetting link
ata3.15: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata3.00: hard resetting link
ata3.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata3.01: hard resetting link
ata3.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.02: hard resetting link
ata3.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.04: hard resetting link
ata3.04: SATA link down (SStatus 0 SControl 320)
ata3.05: hard resetting link
ata3.05: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata3.00: configured for UDMA/100
ata3.01: configured for UDMA/100
ata3.02: configured for UDMA/100
ata3: EH complete
scsi 2:0:0:0: Direct-Access ATA Super Talent Tec Rev PQ: 0 ANSI: 5
sd 2:0:0:0: [sda] 127923200 512-byte hardware sectors (65497 MB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sd 2:0:0:0: [sda] 127923200 512-byte hardware sectors (65497 MB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1
sd 2:0:0:0: [sda] Attached SCSI disk
sd 2:0:0:0: Attached scsi generic sg0 type 0
scsi 2:1:0:0: Direct-Access ATA Super Talent Tec Rev PQ: 0 ANSI: 5
sd 2:1:0:0: [sdb] 127923200 512-byte hardware sectors (65497 MB)
sd 2:1:0:0: [sdb] Write Protect is off
sd 2:1:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 2:1:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sd 2:1:0:0: [sdb] 127923200 512-byte hardware sectors (65497 MB)
sd 2:1:0:0: [sdb] Write Protect is off
sd 2:1:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 2:1:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sdb: sdb1
sd 2:1:0:0: [sdb] Attached SCSI disk
sd 2:1:0:0: Attached scsi generic sg1 type 0
scsi 2:2:0:0: Direct-Access ATA Super Talent Tec Rev PQ: 0 ANSI: 5
sd 2:2:0:0: [sdc] 127923200 512-byte hardware sectors (65497 MB)
sd 2:2:0:0: [sdc] Write Protect is off
sd 2:2:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:2:0:0: [sdc] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sd 2:2:0:0: [sdc] 127923200 512-byte hardware sectors (65497 MB)
sd 2:2:0:0: [sdc] Write Protect is off
sd 2:2:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:2:0:0: [sdc] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sdc: sdc1
sd 2:2:0:0: [sdc] Attached SCSI disk
sd 2:2:0:0: Attached scsi generic sg2 type 0
next prev parent reply other threads:[~2008-05-21 19:42 UTC|newest]
Thread overview: 30+ messages / expand[flat|nested] mbox.gz Atom feed top
2008-05-18 16:15 [PATCHSET #upstream-fixes] libata: fix a bunch of PMP related problems Tejun Heo
2008-05-18 16:15 ` [PATCH 01/10] libata: fix sata_link_hardreset() @online out parameter handling Tejun Heo
2008-05-19 21:53 ` Jeff Garzik
2008-05-18 16:15 ` [PATCH 02/10] libata: reorganize ata_eh_reset() no reset method path Tejun Heo
2008-05-18 16:15 ` [PATCH 03/10] libata: move reset freeze/thaw handling into ata_eh_reset() Tejun Heo
2008-05-18 16:15 ` [PATCH 04/10] libata: kill hotplug related race condition Tejun Heo
2008-05-18 16:15 ` [PATCH 05/10] libata: ignore recovered PHY errors Tejun Heo
2008-05-19 21:50 ` Jeff Garzik
2008-05-18 16:15 ` [PATCH 06/10] libata: increase PMP register access timeout to 3s Tejun Heo
2008-05-18 16:15 ` [PATCH 07/10] libata: make sure PMP notification is turned off during recovery Tejun Heo
2008-05-18 16:15 ` [PATCH 08/10] libata: don't schedule LPM action seperately during probing Tejun Heo
2008-05-18 16:15 ` [PATCH 09/10] sata_sil24: don't use NCQ if marvell 4140 PMP is attached Tejun Heo
2008-05-18 21:14 ` Mark Lord
2008-05-18 16:15 ` [PATCH 10/10] libata: ignore SIMG4726 config pseudo device Tejun Heo
2008-05-18 16:29 ` [PATCHSET #upstream-fixes] git tree available Tejun Heo
2008-05-20 1:35 ` Brian & Chamaigne Scamman
2008-05-20 2:58 ` Mark Lord
2008-05-20 4:28 ` Tejun Heo
2008-05-20 4:43 ` Tejun Heo
2008-05-21 1:32 ` Brian & Chamaigne Scamman
2008-05-21 4:59 ` Tejun Heo
2008-05-21 11:14 ` Brian & Chamaigne Scamman
2008-05-21 19:42 ` Brian & Chamaigne Scamman [this message]
2008-05-22 0:40 ` Tejun Heo
2008-05-23 0:49 ` Brian & Chamaigne Scamman
2008-05-23 1:04 ` Tejun Heo
2008-05-29 3:06 ` Tejun Heo
2008-05-29 3:11 ` Brian & Chamaigne Scamman
2008-05-20 12:08 ` Brian & Chamaigne Scamman
2008-05-20 14:50 ` Tejun Heo
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to='00b901c8bb7a$caaa1ed0$6917a8c0@parents' \
--to=scammanbc@earthlink.net \
--cc=htejun@gmail.com \
--cc=jeff@garzik.org \
--cc=liml@rtr.ca \
--cc=linux-ide@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.