From: "Jonathan Vardy" <jonathanv@explainerdc.com>
To: Jonathan Vardy <jonathanv@explainerdc.com>,
"Peter L. Ashford" <ashford@sdsc.edu>,
Stephan van Hienen <raid@a2000.nu>
Cc: Jonathan Vardy <jonathan@explainerdc.com>,
linux-raid@vger.kernel.org, linux-kernel@vger.kernel.org
Subject: Re: RAID 5 performance problems
Date: Fri, 4 Apr 2003 00:16:37 +0200 [thread overview]
Message-ID: <00d901c2fa2e$b1d4d430$2e77c23e@pentium4> (raw)
In-Reply-To: 00bf01c2fa2d$afafedd0$2e77c23e@pentium4
All info regarding the drive part:
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller on PCI bus 00 dev 21
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xd800-0xd807, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xd808-0xd80f, BIOS settings: hdc:DMA, hdd:pio
PDC20270: IDE controller on PCI bus 02 dev 08
PDC20270: chipset revision 2
PDC20270: not 100% native mode: will probe irqs later
PDC20270: (U)DMA Burst Bit ENABLED Primary MASTER Mode Secondary MASTER
Mode.
ide2: BM-DMA at 0x9040-0x9047, BIOS settings: hde:pio, hdf:pio
ide3: BM-DMA at 0x9048-0x904f, BIOS settings: hdg:pio, hdh:pio
PDC20270: IDE controller on PCI bus 02 dev 10
PDC20270: chipset revision 2
PDC20270: not 100% native mode: will probe irqs later
PDC20270: ROM enabled at 0x000dc000
PDC20270: (U)DMA Burst Bit ENABLED Primary MASTER Mode Secondary MASTER
Mode.
ide4: BM-DMA at 0x90c0-0x90c7, BIOS settings: hdi:pio, hdj:pio
ide5: BM-DMA at 0x90c8-0x90cf, BIOS settings: hdk:pio, hdl:pio
hda: Maxtor 2B020H1, ATA DISK drive
hdc: WDC WD1200BB-00CAA1, ATA DISK drive
hde: WDC WD1200BB-60CJA1, ATA DISK drive
hdg: WDC WD1200BB-60CJA1, ATA DISK drive
hdi: WDC WD1200BB-60CJA1, ATA DISK drive
hdk: WDC WD1200BB-60CJA1, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
ide2 at 0x9000-0x9007,0x9012 on irq 19
ide3 at 0x9020-0x9027,0x9032 on irq 19
ide4 at 0x9080-0x9087,0x9092 on irq 19
ide5 at 0x90a0-0x90a7,0x90b2 on irq 19
blk: queue c0393144, I/O limit 4095Mb (mask 0xffffffff)
hda: 39062500 sectors (20000 MB) w/2048KiB Cache, CHS=2431/255/63, UDMA(33)
blk: queue c03934a8, I/O limit 4095Mb (mask 0xffffffff)
hdc: 234441648 sectors (120034 MB) w/2048KiB Cache, CHS=232581/16/63,
UDMA(33)
blk: queue c039380c, I/O limit 4095Mb (mask 0xffffffff)
hde: 234441648 sectors (120034 MB) w/2048KiB Cache, CHS=232581/16/63,
UDMA(33)
blk: queue c0393b70, I/O limit 4095Mb (mask 0xffffffff)
hdg: 234441648 sectors (120034 MB) w/2048KiB Cache, CHS=232581/16/63,
UDMA(33)
blk: queue c0393ed4, I/O limit 4095Mb (mask 0xffffffff)
hdi: 234441648 sectors (120034 MB) w/2048KiB Cache, CHS=232581/16/63,
UDMA(33)
blk: queue c0394238, I/O limit 4095Mb (mask 0xffffffff)
hdk: 234441648 sectors (120034 MB) w/2048KiB Cache, CHS=232581/16/63,
UDMA(33)
WARNING: multiple messages have this Message-ID (diff)
From: "Jonathan Vardy" <jonathanv@explainerdc.com>
To: "Jonathan Vardy" <jonathanv@explainerdc.com>,
"Peter L. Ashford" <ashford@sdsc.edu>,
"Stephan van Hienen" <raid@a2000.nu>
Cc: "Jonathan Vardy" <jonathan@explainerdc.com>,
<linux-raid@vger.kernel.org>, <linux-kernel@vger.kernel.org>
Subject: Re: RAID 5 performance problems
Date: Fri, 4 Apr 2003 00:16:37 +0200 [thread overview]
Message-ID: <00d901c2fa2e$b1d4d430$2e77c23e@pentium4> (raw)
In-Reply-To: 00bf01c2fa2d$afafedd0$2e77c23e@pentium4
All info regarding the drive part:
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller on PCI bus 00 dev 21
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xd800-0xd807, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xd808-0xd80f, BIOS settings: hdc:DMA, hdd:pio
PDC20270: IDE controller on PCI bus 02 dev 08
PDC20270: chipset revision 2
PDC20270: not 100% native mode: will probe irqs later
PDC20270: (U)DMA Burst Bit ENABLED Primary MASTER Mode Secondary MASTER
Mode.
ide2: BM-DMA at 0x9040-0x9047, BIOS settings: hde:pio, hdf:pio
ide3: BM-DMA at 0x9048-0x904f, BIOS settings: hdg:pio, hdh:pio
PDC20270: IDE controller on PCI bus 02 dev 10
PDC20270: chipset revision 2
PDC20270: not 100% native mode: will probe irqs later
PDC20270: ROM enabled at 0x000dc000
PDC20270: (U)DMA Burst Bit ENABLED Primary MASTER Mode Secondary MASTER
Mode.
ide4: BM-DMA at 0x90c0-0x90c7, BIOS settings: hdi:pio, hdj:pio
ide5: BM-DMA at 0x90c8-0x90cf, BIOS settings: hdk:pio, hdl:pio
hda: Maxtor 2B020H1, ATA DISK drive
hdc: WDC WD1200BB-00CAA1, ATA DISK drive
hde: WDC WD1200BB-60CJA1, ATA DISK drive
hdg: WDC WD1200BB-60CJA1, ATA DISK drive
hdi: WDC WD1200BB-60CJA1, ATA DISK drive
hdk: WDC WD1200BB-60CJA1, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
ide2 at 0x9000-0x9007,0x9012 on irq 19
ide3 at 0x9020-0x9027,0x9032 on irq 19
ide4 at 0x9080-0x9087,0x9092 on irq 19
ide5 at 0x90a0-0x90a7,0x90b2 on irq 19
blk: queue c0393144, I/O limit 4095Mb (mask 0xffffffff)
hda: 39062500 sectors (20000 MB) w/2048KiB Cache, CHS=2431/255/63, UDMA(33)
blk: queue c03934a8, I/O limit 4095Mb (mask 0xffffffff)
hdc: 234441648 sectors (120034 MB) w/2048KiB Cache, CHS=232581/16/63,
UDMA(33)
blk: queue c039380c, I/O limit 4095Mb (mask 0xffffffff)
hde: 234441648 sectors (120034 MB) w/2048KiB Cache, CHS=232581/16/63,
UDMA(33)
blk: queue c0393b70, I/O limit 4095Mb (mask 0xffffffff)
hdg: 234441648 sectors (120034 MB) w/2048KiB Cache, CHS=232581/16/63,
UDMA(33)
blk: queue c0393ed4, I/O limit 4095Mb (mask 0xffffffff)
hdi: 234441648 sectors (120034 MB) w/2048KiB Cache, CHS=232581/16/63,
UDMA(33)
blk: queue c0394238, I/O limit 4095Mb (mask 0xffffffff)
hdk: 234441648 sectors (120034 MB) w/2048KiB Cache, CHS=232581/16/63,
UDMA(33)
next prev parent reply other threads:[~2003-04-03 22:16 UTC|newest]
Thread overview: 43+ messages / expand[flat|nested] mbox.gz Atom feed top
2003-04-03 15:45 RAID 5 performance problems Jonathan Vardy
2003-04-03 15:45 ` Jonathan Vardy
2003-04-03 18:05 ` Peter L. Ashford
2003-04-03 18:05 ` Peter L. Ashford
2003-04-03 18:47 ` Ross Vandegrift
2003-04-03 19:22 ` Stephan van Hienen
2003-04-03 19:20 ` Stephan van Hienen
2003-04-03 19:28 ` Alan Cox
2003-04-03 21:02 ` Ezra Nugroho
2003-04-03 21:25 ` Stephan van Hienen
2003-04-03 21:38 ` Peter L. Ashford
2003-04-03 21:38 ` Peter L. Ashford
2003-04-03 22:09 ` Jonathan Vardy
2003-04-03 22:09 ` Jonathan Vardy
2003-04-03 22:16 ` Jonathan Vardy [this message]
2003-04-03 22:16 ` Jonathan Vardy
2003-04-03 22:28 ` Peter L. Ashford
2003-04-03 22:28 ` Peter L. Ashford
2003-04-03 21:42 ` Jonathan Vardy
2003-04-03 21:42 ` Jonathan Vardy
2003-04-03 22:13 ` Peter L. Ashford
2003-04-03 22:13 ` Peter L. Ashford
2003-04-04 20:39 ` H. Peter Anvin
2003-04-03 21:06 ` Felipe Alfaro Solana
2003-04-03 21:14 ` Jonathan Vardy
2003-04-03 21:14 ` Jonathan Vardy
-- strict thread matches above, loose matches on Subject: below --
2003-04-03 19:13 Neil Schemenauer
2003-04-03 19:49 Andy Arvai
2003-04-03 20:25 ` Mike Dresser
2003-04-03 20:25 ` Mike Dresser
2003-04-03 21:10 ` Jonathan Vardy
2003-04-03 21:10 ` Jonathan Vardy
2003-04-03 21:31 ` Ezra Nugroho
2003-04-03 20:10 Chuck Ebbert
2003-04-04 11:44 Jonathan Vardy
2003-04-04 11:44 ` Jonathan Vardy
2003-04-04 14:39 ` Ezra Nugroho
2003-04-04 15:05 Jonathan Vardy
2003-04-04 15:05 ` Jonathan Vardy
2003-04-04 16:01 Jonathan Vardy
2003-04-04 16:01 ` Jonathan Vardy
2003-04-05 0:10 ` Jonathan Vardy
2003-04-05 0:10 ` Jonathan Vardy
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to='00d901c2fa2e$b1d4d430$2e77c23e@pentium4' \
--to=jonathanv@explainerdc.com \
--cc=ashford@sdsc.edu \
--cc=jonathan@explainerdc.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-raid@vger.kernel.org \
--cc=raid@a2000.nu \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.