Re: [PATCH 3/3] arm64: dts: rockchip: add Quartz64-A sdmmc1 node

[Johan Jonker <jbx6244@gmail.com>]

On 1/27/22 02:00, Peter Geis wrote:
> The sdmmc1 node on Quartz64-A supports the optional wifi module from
> Pine64.
> Add the sdmmc1 node and requisite sdio_pwrseq to enable wifi support on
> the Quartz64-A.
> 
> Signed-off-by: Peter Geis <pgwipeout@gmail.com>
> ---
>  .../boot/dts/rockchip/rk3566-quartz64-a.dts   | 45 +++++++++++++++++++
>  1 file changed, 45 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/rockchip/rk3566-quartz64-a.dts b/arch/arm64/boot/dts/rockchip/rk3566-quartz64-a.dts
> index 33c2c18caaa9..1d73ac6557c5 100644
> --- a/arch/arm64/boot/dts/rockchip/rk3566-quartz64-a.dts
> +++ b/arch/arm64/boot/dts/rockchip/rk3566-quartz64-a.dts
> @@ -91,6 +91,18 @@ simple-audio-card,codec {
>  		};
>  	};
>  
> +	sdio_pwrseq: sdio-pwrseq {

> +		status = "okay";

When a node is not previously disabled, then there's no need for "okay".

> +		compatible = "mmc-pwrseq-simple";
> +		clocks = <&rk817 1>;
> +		clock-names = "ext_clock";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&wifi_enable_h>;
> +		reset-gpios = <&gpio2 RK_PC2 GPIO_ACTIVE_LOW>;
> +		post-power-on-delay-ms = <100>;
> +		power-off-delay-us = <5000000>;
> +	};
> +
>  	vcc12v_dcin: vcc12v_dcin {
>  		compatible = "regulator-fixed";
>  		regulator-name = "vcc12v_dcin";
> @@ -147,6 +159,17 @@ vcc_sys: vcc_sys {
>  		regulator-max-microvolt = <4400000>;
>  		vin-supply = <&vbus>;
>  	};
> +
> +	/* sourced from vcc_sys, sdio module operates internally at 3.3v */
> +	vcc_wl: vcc_wl {
> +		compatible = "regulator-fixed";
> +		regulator-name = "vcc_wl";
> +		regulator-always-on;
> +		regulator-boot-on;
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		vin-supply = <&vcc_sys>;
> +	};
>  };
>  
>  &cpu0 {
> @@ -475,6 +498,12 @@ pmic_int_l: pmic-int-l {
>  		};
>  	};
>  
> +	sdio-pwrseq {
> +		wifi_enable_h: wifi-enable-h {
> +			rockchip,pins = <2 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;
> +		};
> +	};
> +
>  	vcc_sd {
>  		vcc_sd_h: vcc-sd-h {
>  			rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
> @@ -516,6 +545,22 @@ &sdmmc0 {
>  	status = "okay";
>  };
>  
> +&sdmmc1 {
> +	bus-width = <4>;
> +	cap-sd-highspeed;
> +	cap-sdio-irq;

> +	disable-wp;

From mmc-controller.yaml:

  disable-wp:
    $ref: /schemas/types.yaml#/definitions/flag
    description:
      When set, no physical write-protect line is present. This
      property should only be specified when the controller has a
      dedicated write-protect detection logic. If a GPIO is always used
      for the write-protect detection logic, it is sufficient to not
      specify the wp-gpios property in the absence of a write-protect
      line. Not used in combination with eMMC or SDIO.

> +	keep-power-in-suspend;
> +	mmc-pwrseq = <&sdio_pwrseq>;
> +	non-removable;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&sdmmc1_bus4 &sdmmc1_cmd &sdmmc1_clk>;
> +	sd-uhs-sdr104;
> +	vmmc-supply = <&vcc_wl>;
> +	vqmmc-supply = <&vcc_1v8>;
> +	status = "okay";
> +};
> +
>  &spdif {
>  	status = "okay";
>  };

_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip