* [PATCH V2 2/2] ARM: dts: rockchip: add dts for RK3288-Tinker board
@ 2017-02-06 2:14 ` Eddie Cai
0 siblings, 0 replies; 26+ messages in thread
From: Eddie Cai @ 2017-02-06 2:14 UTC (permalink / raw)
To: robh+dt, mark.rutland, heiko
Cc: linux, devicetree, linux-arm-kernel, linux-rockchip, linux-kernel,
eddie.cai
This patch add basic support for RK3288-Tinker board. We can boot in to rootfs
with this patch.
Signed-off-by: Eddie Cai <eddie.cai@rock-chips.com>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/rk3288-tinker.dts | 543 ++++++++++++++++++++++++++++++++++++
2 files changed, 544 insertions(+)
create mode 100644 arch/arm/boot/dts/rk3288-tinker.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 7327250..4fc05b7 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -679,6 +679,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += \
rk3288-popmetal.dtb \
rk3288-r89.dtb \
rk3288-rock2-square.dtb \
+ rk3288-tinker.dtb \
rk3288-veyron-brain.dtb \
rk3288-veyron-jaq.dtb \
rk3288-veyron-jerry.dtb \
diff --git a/arch/arm/boot/dts/rk3288-tinker.dts b/arch/arm/boot/dts/rk3288-tinker.dts
new file mode 100644
index 0000000..c48563e
--- /dev/null
+++ b/arch/arm/boot/dts/rk3288-tinker.dts
@@ -0,0 +1,543 @@
+/*
+ * Copyright (c) 2017 Fuzhou Rockchip Electronics Co., Ltd.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "rk3288.dtsi"
+
+/ {
+ model = "Rockchip RK3288 Tinker Board";
+ compatible = "asus,rk3288-tinker", "rockchip,rk3288";
+
+ memory {
+ reg = <0x0 0x80000000>;
+ device_type = "memory";
+ };
+
+ ext_gmac: external-gmac-clock {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <125000000>;
+ clock-output-names = "ext_gmac";
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ autorepeat;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwrbtn>;
+
+ button@0 {
+ gpios = <&gpio0 5 GPIO_ACTIVE_LOW>;
+ linux,code = <116>;
+ label = "GPIO Key Power";
+ linux,input-type = <1>;
+ gpio-key,wakeup = <1>;
+ debounce-interval = <100>;
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+
+ pwr-led {
+ gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "default-on";
+ };
+
+ act-led {
+ gpios=<&gpio2 3 GPIO_ACTIVE_LOW>;
+ linux,default-trigger="mmc0";
+ };
+ };
+
+ sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,format = "i2s";
+ simple-audio-card,name = "rockchip,tinker-codec";
+ simple-audio-card,mclk-fs = <512>;
+ simple-audio-card,cpu {
+ sound-dai = <&i2s>;
+ };
+ simple-audio-card,codec {
+ sound-dai = <&hdmi>;
+ };
+ };
+
+ vcc_sys: vsys-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_sys";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vcc_sd: sdmmc-regulator {
+ compatible = "regulator-fixed";
+ gpio = <&gpio7 11 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc_pwr>;
+ regulator-name = "vcc_sd";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ startup-delay-us = <100000>;
+ vin-supply = <&vcc_io>;
+ };
+};
+
+&cpu0 {
+ cpu0-supply = <&vdd_cpu>;
+};
+
+&gmac {
+ phy-supply = <&vcc33_lan>;
+ phy-mode = "rgmii";
+ clock_in_out = "input";
+ snps,reset-gpio = <&gpio4 7 0>;
+ snps,reset-active-low;
+ snps,reset-delays-us = <0 10000 1000000>;
+ assigned-clocks = <&cru SCLK_MAC>;
+ assigned-clock-parents = <&ext_gmac>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&rgmii_pins>;
+ tx_delay = <0x30>;
+ rx_delay = <0x10>;
+ status = "ok";
+};
+
+&hdmi {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #sound-dai-cells = <0>;
+ ddc-i2c-bus = <&i2c5>;
+ status = "okay";
+ /* Don't use vopl for HDMI */
+ ports {
+ hdmi_in: port {
+ /delete-node/ endpoint@1;
+ };
+ };
+};
+
+&i2c0 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ rk808: pmic@1b {
+ compatible = "rockchip,rk808";
+ reg = <0x1b>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_int &global_pwroff &dvs_1 &dvs_2>;
+ dvs-gpios = <&gpio0 11 GPIO_ACTIVE_HIGH>,
+ <&gpio0 12 GPIO_ACTIVE_HIGH>;
+
+ rockchip,system-power-controller;
+ wakeup-source;
+ #clock-cells = <1>;
+ clock-output-names = "xin32k", "rk808-clkout2";
+
+ vcc1-supply = <&vcc_sys>;
+ vcc2-supply = <&vcc_sys>;
+ vcc3-supply = <&vcc_sys>;
+ vcc4-supply = <&vcc_sys>;
+ vcc6-supply = <&vcc_sys>;
+ vcc7-supply = <&vcc_sys>;
+ vcc8-supply = <&vcc_io>;
+ vcc9-supply = <&vcc_io>;
+ vcc10-supply = <&vcc_io>;
+ vcc11-supply = <&vcc_sys>;
+ vcc12-supply = <&vcc_io>;
+ vddio-supply = <&vcc_io>;
+
+ regulators {
+ vdd_cpu: DCDC_REG1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-name = "vdd_arm";
+ regulator-ramp-delay = <6000>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_gpu: DCDC_REG2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <1250000>;
+ regulator-name = "vdd_gpu";
+ regulator-ramp-delay = <6000>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1000000>;
+ };
+ };
+
+ vcc_ddr: DCDC_REG3 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-name = "vcc_ddr";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vcc_io: DCDC_REG4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc_io";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vcc18_ldo1: LDO_REG1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc18_ldo1";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vcc33_mipi: LDO_REG2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc33_mipi";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_10: LDO_REG3 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-name = "vdd_10";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1000000>;
+ };
+ };
+
+ vcc18_codec: LDO_REG4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc18_codec";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vccio_sd: LDO_REG5 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vccio_sd";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vdd10_lcd: LDO_REG6 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-name = "vdd10_lcd";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1000000>;
+ };
+ };
+
+ vcc_18: LDO_REG7 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc_18";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vcc18_lcd: LDO_REG8 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc18_lcd";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vcc33_sd: SWITCH_REG1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-name = "vcc33_sd";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vcc33_lan: SWITCH_REG2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-name = "vcc33_lan";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+ };
+ };
+};
+
+&i2c2 {
+ status = "okay";
+};
+
+&i2c5 {
+ status = "okay";
+};
+
+&i2s {
+ #sound-dai-cells = <0>;
+ status = "okay";
+};
+
+&io_domains {
+ status = "okay";
+
+ sdcard-supply = <&vccio_sd>;
+};
+
+&pinctrl {
+ pcfg_pull_none_drv_8ma: pcfg-pull-none-drv-8ma {
+ drive-strength = <8>;
+ };
+
+ pcfg_pull_up_drv_8ma: pcfg-pull-up-drv-8ma {
+ bias-pull-up;
+ drive-strength = <8>;
+ };
+
+ backlight {
+ bl_en: bl-en {
+ rockchip,pins = <7 2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ buttons {
+ pwrbtn: pwrbtn {
+ rockchip,pins = <0 5 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ eth_phy {
+ eth_phy_pwr: eth-phy-pwr {
+ rockchip,pins = <0 6 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ pmic {
+ pmic_int: pmic-int {
+ rockchip,pins = <RK_GPIO0 4 RK_FUNC_GPIO \
+ &pcfg_pull_up>;
+ };
+
+ dvs_1: dvs-1 {
+ rockchip,pins = <RK_GPIO0 11 RK_FUNC_GPIO \
+ &pcfg_pull_down>;
+ };
+
+ dvs_2: dvs-2 {
+ rockchip,pins = <RK_GPIO0 12 RK_FUNC_GPIO \
+ &pcfg_pull_down>;
+ };
+ };
+
+ sdmmc {
+ sdmmc_bus4: sdmmc-bus4 {
+ rockchip,pins = <6 16 RK_FUNC_1 &pcfg_pull_up_drv_8ma>,
+ <6 17 RK_FUNC_1 &pcfg_pull_up_drv_8ma>,
+ <6 18 RK_FUNC_1 &pcfg_pull_up_drv_8ma>,
+ <6 19 RK_FUNC_1 &pcfg_pull_up_drv_8ma>;
+ };
+
+ sdmmc_clk: sdmmc-clk {
+ rockchip,pins = <6 20 RK_FUNC_1 \
+ &pcfg_pull_none_drv_8ma>;
+ };
+
+ sdmmc_cmd: sdmmc-cmd {
+ rockchip,pins = <6 21 RK_FUNC_1 &pcfg_pull_up_drv_8ma>;
+ };
+
+ sdmmc_pwr: sdmmc-pwr {
+ rockchip,pins = <7 11 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ usb {
+ host_vbus_drv: host-vbus-drv {
+ rockchip,pins = <0 14 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ pwr_3g: pwr-3g {
+ rockchip,pins = <7 8 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
+
+&pwm0 {
+ status = "okay";
+};
+
+&saradc {
+ vref-supply = <&vcc18_ldo1>;
+ status ="okay";
+};
+
+&sdmmc {
+ bus-width = <4>;
+ cap-mmc-highspeed;
+ cap-sd-highspeed;
+ card-detect-delay = <200>;
+ disable-wp; /* wp not hooked up */
+ num-slots = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_bus4>;
+ status = "okay";
+ vmmc-supply = <&vcc33_sd>;
+ vqmmc-supply = <&vccio_sd>;
+};
+
+&tsadc {
+ rockchip,hw-tshut-mode = <1>; /* tshut mode 0:CRU 1:GPIO */
+ rockchip,hw-tshut-polarity = <1>; /* tshut polarity 0:LOW 1:HIGH */
+ status = "okay";
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&uart1 {
+ status = "okay";
+};
+
+&uart2 {
+ status = "okay";
+};
+
+&uart3 {
+ status = "okay";
+};
+
+&uart4 {
+ status = "okay";
+};
+
+&usbphy {
+ status = "okay";
+};
+
+&usb_host0_ehci {
+ status = "okay";
+};
+
+&usb_host1 {
+ status = "okay";
+};
+
+&usb_otg {
+ status= "okay";
+};
+
+&vopb {
+ status = "okay";
+};
+
+&vopb_mmu {
+ status = "okay";
+};
+
+&vopl {
+ status = "okay";
+ /* Don't use vopl for HDMI */
+ vopl_out: port {
+ /delete-node/ endpoint@0;
+ };
+};
+
+&vopl_mmu {
+ status = "okay";
+};
+
+&wdt {
+ status = "okay";
+};
+
--
2.7.4
^ permalink raw reply related [flat|nested] 26+ messages in thread* [PATCH V2 2/2] ARM: dts: rockchip: add dts for RK3288-Tinker board
@ 2017-02-06 2:14 ` Eddie Cai
0 siblings, 0 replies; 26+ messages in thread
From: Eddie Cai @ 2017-02-06 2:14 UTC (permalink / raw)
To: linux-arm-kernel
This patch add basic support for RK3288-Tinker board. We can boot in to rootfs
with this patch.
Signed-off-by: Eddie Cai <eddie.cai@rock-chips.com>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/rk3288-tinker.dts | 543 ++++++++++++++++++++++++++++++++++++
2 files changed, 544 insertions(+)
create mode 100644 arch/arm/boot/dts/rk3288-tinker.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 7327250..4fc05b7 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -679,6 +679,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += \
rk3288-popmetal.dtb \
rk3288-r89.dtb \
rk3288-rock2-square.dtb \
+ rk3288-tinker.dtb \
rk3288-veyron-brain.dtb \
rk3288-veyron-jaq.dtb \
rk3288-veyron-jerry.dtb \
diff --git a/arch/arm/boot/dts/rk3288-tinker.dts b/arch/arm/boot/dts/rk3288-tinker.dts
new file mode 100644
index 0000000..c48563e
--- /dev/null
+++ b/arch/arm/boot/dts/rk3288-tinker.dts
@@ -0,0 +1,543 @@
+/*
+ * Copyright (c) 2017 Fuzhou Rockchip Electronics Co., Ltd.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "rk3288.dtsi"
+
+/ {
+ model = "Rockchip RK3288 Tinker Board";
+ compatible = "asus,rk3288-tinker", "rockchip,rk3288";
+
+ memory {
+ reg = <0x0 0x80000000>;
+ device_type = "memory";
+ };
+
+ ext_gmac: external-gmac-clock {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <125000000>;
+ clock-output-names = "ext_gmac";
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ autorepeat;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwrbtn>;
+
+ button at 0 {
+ gpios = <&gpio0 5 GPIO_ACTIVE_LOW>;
+ linux,code = <116>;
+ label = "GPIO Key Power";
+ linux,input-type = <1>;
+ gpio-key,wakeup = <1>;
+ debounce-interval = <100>;
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+
+ pwr-led {
+ gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "default-on";
+ };
+
+ act-led {
+ gpios=<&gpio2 3 GPIO_ACTIVE_LOW>;
+ linux,default-trigger="mmc0";
+ };
+ };
+
+ sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,format = "i2s";
+ simple-audio-card,name = "rockchip,tinker-codec";
+ simple-audio-card,mclk-fs = <512>;
+ simple-audio-card,cpu {
+ sound-dai = <&i2s>;
+ };
+ simple-audio-card,codec {
+ sound-dai = <&hdmi>;
+ };
+ };
+
+ vcc_sys: vsys-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_sys";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vcc_sd: sdmmc-regulator {
+ compatible = "regulator-fixed";
+ gpio = <&gpio7 11 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc_pwr>;
+ regulator-name = "vcc_sd";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ startup-delay-us = <100000>;
+ vin-supply = <&vcc_io>;
+ };
+};
+
+&cpu0 {
+ cpu0-supply = <&vdd_cpu>;
+};
+
+&gmac {
+ phy-supply = <&vcc33_lan>;
+ phy-mode = "rgmii";
+ clock_in_out = "input";
+ snps,reset-gpio = <&gpio4 7 0>;
+ snps,reset-active-low;
+ snps,reset-delays-us = <0 10000 1000000>;
+ assigned-clocks = <&cru SCLK_MAC>;
+ assigned-clock-parents = <&ext_gmac>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&rgmii_pins>;
+ tx_delay = <0x30>;
+ rx_delay = <0x10>;
+ status = "ok";
+};
+
+&hdmi {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #sound-dai-cells = <0>;
+ ddc-i2c-bus = <&i2c5>;
+ status = "okay";
+ /* Don't use vopl for HDMI */
+ ports {
+ hdmi_in: port {
+ /delete-node/ endpoint at 1;
+ };
+ };
+};
+
+&i2c0 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ rk808: pmic at 1b {
+ compatible = "rockchip,rk808";
+ reg = <0x1b>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_int &global_pwroff &dvs_1 &dvs_2>;
+ dvs-gpios = <&gpio0 11 GPIO_ACTIVE_HIGH>,
+ <&gpio0 12 GPIO_ACTIVE_HIGH>;
+
+ rockchip,system-power-controller;
+ wakeup-source;
+ #clock-cells = <1>;
+ clock-output-names = "xin32k", "rk808-clkout2";
+
+ vcc1-supply = <&vcc_sys>;
+ vcc2-supply = <&vcc_sys>;
+ vcc3-supply = <&vcc_sys>;
+ vcc4-supply = <&vcc_sys>;
+ vcc6-supply = <&vcc_sys>;
+ vcc7-supply = <&vcc_sys>;
+ vcc8-supply = <&vcc_io>;
+ vcc9-supply = <&vcc_io>;
+ vcc10-supply = <&vcc_io>;
+ vcc11-supply = <&vcc_sys>;
+ vcc12-supply = <&vcc_io>;
+ vddio-supply = <&vcc_io>;
+
+ regulators {
+ vdd_cpu: DCDC_REG1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-name = "vdd_arm";
+ regulator-ramp-delay = <6000>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_gpu: DCDC_REG2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <1250000>;
+ regulator-name = "vdd_gpu";
+ regulator-ramp-delay = <6000>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1000000>;
+ };
+ };
+
+ vcc_ddr: DCDC_REG3 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-name = "vcc_ddr";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vcc_io: DCDC_REG4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc_io";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vcc18_ldo1: LDO_REG1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc18_ldo1";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vcc33_mipi: LDO_REG2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc33_mipi";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_10: LDO_REG3 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-name = "vdd_10";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1000000>;
+ };
+ };
+
+ vcc18_codec: LDO_REG4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc18_codec";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vccio_sd: LDO_REG5 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vccio_sd";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vdd10_lcd: LDO_REG6 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-name = "vdd10_lcd";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1000000>;
+ };
+ };
+
+ vcc_18: LDO_REG7 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc_18";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vcc18_lcd: LDO_REG8 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc18_lcd";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vcc33_sd: SWITCH_REG1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-name = "vcc33_sd";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vcc33_lan: SWITCH_REG2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-name = "vcc33_lan";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+ };
+ };
+};
+
+&i2c2 {
+ status = "okay";
+};
+
+&i2c5 {
+ status = "okay";
+};
+
+&i2s {
+ #sound-dai-cells = <0>;
+ status = "okay";
+};
+
+&io_domains {
+ status = "okay";
+
+ sdcard-supply = <&vccio_sd>;
+};
+
+&pinctrl {
+ pcfg_pull_none_drv_8ma: pcfg-pull-none-drv-8ma {
+ drive-strength = <8>;
+ };
+
+ pcfg_pull_up_drv_8ma: pcfg-pull-up-drv-8ma {
+ bias-pull-up;
+ drive-strength = <8>;
+ };
+
+ backlight {
+ bl_en: bl-en {
+ rockchip,pins = <7 2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ buttons {
+ pwrbtn: pwrbtn {
+ rockchip,pins = <0 5 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ eth_phy {
+ eth_phy_pwr: eth-phy-pwr {
+ rockchip,pins = <0 6 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ pmic {
+ pmic_int: pmic-int {
+ rockchip,pins = <RK_GPIO0 4 RK_FUNC_GPIO \
+ &pcfg_pull_up>;
+ };
+
+ dvs_1: dvs-1 {
+ rockchip,pins = <RK_GPIO0 11 RK_FUNC_GPIO \
+ &pcfg_pull_down>;
+ };
+
+ dvs_2: dvs-2 {
+ rockchip,pins = <RK_GPIO0 12 RK_FUNC_GPIO \
+ &pcfg_pull_down>;
+ };
+ };
+
+ sdmmc {
+ sdmmc_bus4: sdmmc-bus4 {
+ rockchip,pins = <6 16 RK_FUNC_1 &pcfg_pull_up_drv_8ma>,
+ <6 17 RK_FUNC_1 &pcfg_pull_up_drv_8ma>,
+ <6 18 RK_FUNC_1 &pcfg_pull_up_drv_8ma>,
+ <6 19 RK_FUNC_1 &pcfg_pull_up_drv_8ma>;
+ };
+
+ sdmmc_clk: sdmmc-clk {
+ rockchip,pins = <6 20 RK_FUNC_1 \
+ &pcfg_pull_none_drv_8ma>;
+ };
+
+ sdmmc_cmd: sdmmc-cmd {
+ rockchip,pins = <6 21 RK_FUNC_1 &pcfg_pull_up_drv_8ma>;
+ };
+
+ sdmmc_pwr: sdmmc-pwr {
+ rockchip,pins = <7 11 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ usb {
+ host_vbus_drv: host-vbus-drv {
+ rockchip,pins = <0 14 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ pwr_3g: pwr-3g {
+ rockchip,pins = <7 8 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
+
+&pwm0 {
+ status = "okay";
+};
+
+&saradc {
+ vref-supply = <&vcc18_ldo1>;
+ status ="okay";
+};
+
+&sdmmc {
+ bus-width = <4>;
+ cap-mmc-highspeed;
+ cap-sd-highspeed;
+ card-detect-delay = <200>;
+ disable-wp; /* wp not hooked up */
+ num-slots = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_bus4>;
+ status = "okay";
+ vmmc-supply = <&vcc33_sd>;
+ vqmmc-supply = <&vccio_sd>;
+};
+
+&tsadc {
+ rockchip,hw-tshut-mode = <1>; /* tshut mode 0:CRU 1:GPIO */
+ rockchip,hw-tshut-polarity = <1>; /* tshut polarity 0:LOW 1:HIGH */
+ status = "okay";
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&uart1 {
+ status = "okay";
+};
+
+&uart2 {
+ status = "okay";
+};
+
+&uart3 {
+ status = "okay";
+};
+
+&uart4 {
+ status = "okay";
+};
+
+&usbphy {
+ status = "okay";
+};
+
+&usb_host0_ehci {
+ status = "okay";
+};
+
+&usb_host1 {
+ status = "okay";
+};
+
+&usb_otg {
+ status= "okay";
+};
+
+&vopb {
+ status = "okay";
+};
+
+&vopb_mmu {
+ status = "okay";
+};
+
+&vopl {
+ status = "okay";
+ /* Don't use vopl for HDMI */
+ vopl_out: port {
+ /delete-node/ endpoint at 0;
+ };
+};
+
+&vopl_mmu {
+ status = "okay";
+};
+
+&wdt {
+ status = "okay";
+};
+
--
2.7.4
^ permalink raw reply related [flat|nested] 26+ messages in thread* Re: [PATCH V2 2/2] ARM: dts: rockchip: add dts for RK3288-Tinker board
2017-02-06 2:14 ` Eddie Cai
(?)
@ 2017-02-08 23:07 ` Heiko Stuebner
-1 siblings, 0 replies; 26+ messages in thread
From: Heiko Stuebner @ 2017-02-08 23:07 UTC (permalink / raw)
To: Eddie Cai
Cc: mark.rutland, devicetree, linux, linux-kernel, linux-rockchip,
robh+dt, eddie.cai, linux-arm-kernel
Hi Eddie
Am Montag, 6. Februar 2017, 10:14:47 CET schrieb Eddie Cai:
> This patch add basic support for RK3288-Tinker board. We can boot in to
> rootfs with this patch.
>
> Signed-off-by: Eddie Cai <eddie.cai@rock-chips.com>
> ---
[...]
> +&hdmi {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + #sound-dai-cells = <0>;
why are these needed. More importantly if they are needed, they should be in
rk3288.dtsi instead and not here.
> + ddc-i2c-bus = <&i2c5>;
> + status = "okay";
> + /* Don't use vopl for HDMI */
> + ports {
> + hdmi_in: port {
> + /delete-node/ endpoint@1;
> + };
> + };
See comment in previous iteration, about the link to vopl being there in
hardware and not wanting to use it for hdmi being a driver issue.
No working around driver issues in the devicetree, so leave the vop <-> hdmi
links intact please :-)
> +};
> +
> +&i2c0 {
> + status = "okay";
> + clock-frequency = <400000>;
> +
> + rk808: pmic@1b {
> + compatible = "rockchip,rk808";
> + reg = <0x1b>;
> + interrupt-parent = <&gpio0>;
> + interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pmic_int &global_pwroff &dvs_1 &dvs_2>;
> + dvs-gpios = <&gpio0 11 GPIO_ACTIVE_HIGH>,
> + <&gpio0 12 GPIO_ACTIVE_HIGH>;
> +
> + rockchip,system-power-controller;
> + wakeup-source;
> + #clock-cells = <1>;
> + clock-output-names = "xin32k", "rk808-clkout2";
> +
> + vcc1-supply = <&vcc_sys>;
> + vcc2-supply = <&vcc_sys>;
> + vcc3-supply = <&vcc_sys>;
> + vcc4-supply = <&vcc_sys>;
> + vcc6-supply = <&vcc_sys>;
> + vcc7-supply = <&vcc_sys>;
> + vcc8-supply = <&vcc_io>;
> + vcc9-supply = <&vcc_io>;
> + vcc10-supply = <&vcc_io>;
> + vcc11-supply = <&vcc_sys>;
> + vcc12-supply = <&vcc_io>;
> + vddio-supply = <&vcc_io>;
> +
> + regulators {
> + vdd_cpu: DCDC_REG1 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <750000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-name = "vdd_arm";
> + regulator-ramp-delay = <6000>;
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdd_gpu: DCDC_REG2 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <850000>;
> + regulator-max-microvolt = <1250000>;
> + regulator-name = "vdd_gpu";
> + regulator-ramp-delay = <6000>;
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1000000>;
> + };
> + };
> +
> + vcc_ddr: DCDC_REG3 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-name = "vcc_ddr";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> + };
> +
> + vcc_io: DCDC_REG4 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc_io";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <3300000>;
> + };
> + };
> +
> + vcc18_ldo1: LDO_REG1 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc18_ldo1";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1800000>;
> + };
> + };
> +
> + vcc33_mipi: LDO_REG2 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc33_mipi";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdd_10: LDO_REG3 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1000000>;
> + regulator-name = "vdd_10";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1000000>;
> + };
> + };
> +
> + vcc18_codec: LDO_REG4 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc18_codec";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1800000>;
> + };
> + };
> +
> + vccio_sd: LDO_REG5 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vccio_sd";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <3300000>;
> + };
> + };
> +
> + vdd10_lcd: LDO_REG6 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1000000>;
> + regulator-name = "vdd10_lcd";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1000000>;
> + };
> + };
> +
> + vcc_18: LDO_REG7 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc_18";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1800000>;
> + };
> + };
> +
> + vcc18_lcd: LDO_REG8 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc18_lcd";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1800000>;
> + };
> + };
> +
> + vcc33_sd: SWITCH_REG1 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-name = "vcc33_sd";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> + };
> +
> + vcc33_lan: SWITCH_REG2 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-name = "vcc33_lan";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> + };
> + };
> + };
> +};
> +
> +&i2c2 {
> + status = "okay";
> +};
> +
> +&i2c5 {
> + status = "okay";
> +};
> +
> +&i2s {
> + #sound-dai-cells = <0>;
> + status = "okay";
> +};
> +&vopb {
> + status = "okay";
> +};
> +
> +&vopb_mmu {
> + status = "okay";
> +};
> +
> +&vopl {
> + status = "okay";
> + /* Don't use vopl for HDMI */
> + vopl_out: port {
> + /delete-node/ endpoint@0;
> + };
same here
> +};
> +
^ permalink raw reply [flat|nested] 26+ messages in thread* Re: [PATCH V2 2/2] ARM: dts: rockchip: add dts for RK3288-Tinker board
@ 2017-02-08 23:07 ` Heiko Stuebner
0 siblings, 0 replies; 26+ messages in thread
From: Heiko Stuebner @ 2017-02-08 23:07 UTC (permalink / raw)
To: Eddie Cai
Cc: robh+dt, mark.rutland, linux, devicetree, linux-arm-kernel,
linux-rockchip, linux-kernel, eddie.cai
Hi Eddie
Am Montag, 6. Februar 2017, 10:14:47 CET schrieb Eddie Cai:
> This patch add basic support for RK3288-Tinker board. We can boot in to
> rootfs with this patch.
>
> Signed-off-by: Eddie Cai <eddie.cai@rock-chips.com>
> ---
[...]
> +&hdmi {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + #sound-dai-cells = <0>;
why are these needed. More importantly if they are needed, they should be in
rk3288.dtsi instead and not here.
> + ddc-i2c-bus = <&i2c5>;
> + status = "okay";
> + /* Don't use vopl for HDMI */
> + ports {
> + hdmi_in: port {
> + /delete-node/ endpoint@1;
> + };
> + };
See comment in previous iteration, about the link to vopl being there in
hardware and not wanting to use it for hdmi being a driver issue.
No working around driver issues in the devicetree, so leave the vop <-> hdmi
links intact please :-)
> +};
> +
> +&i2c0 {
> + status = "okay";
> + clock-frequency = <400000>;
> +
> + rk808: pmic@1b {
> + compatible = "rockchip,rk808";
> + reg = <0x1b>;
> + interrupt-parent = <&gpio0>;
> + interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pmic_int &global_pwroff &dvs_1 &dvs_2>;
> + dvs-gpios = <&gpio0 11 GPIO_ACTIVE_HIGH>,
> + <&gpio0 12 GPIO_ACTIVE_HIGH>;
> +
> + rockchip,system-power-controller;
> + wakeup-source;
> + #clock-cells = <1>;
> + clock-output-names = "xin32k", "rk808-clkout2";
> +
> + vcc1-supply = <&vcc_sys>;
> + vcc2-supply = <&vcc_sys>;
> + vcc3-supply = <&vcc_sys>;
> + vcc4-supply = <&vcc_sys>;
> + vcc6-supply = <&vcc_sys>;
> + vcc7-supply = <&vcc_sys>;
> + vcc8-supply = <&vcc_io>;
> + vcc9-supply = <&vcc_io>;
> + vcc10-supply = <&vcc_io>;
> + vcc11-supply = <&vcc_sys>;
> + vcc12-supply = <&vcc_io>;
> + vddio-supply = <&vcc_io>;
> +
> + regulators {
> + vdd_cpu: DCDC_REG1 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <750000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-name = "vdd_arm";
> + regulator-ramp-delay = <6000>;
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdd_gpu: DCDC_REG2 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <850000>;
> + regulator-max-microvolt = <1250000>;
> + regulator-name = "vdd_gpu";
> + regulator-ramp-delay = <6000>;
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1000000>;
> + };
> + };
> +
> + vcc_ddr: DCDC_REG3 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-name = "vcc_ddr";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> + };
> +
> + vcc_io: DCDC_REG4 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc_io";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <3300000>;
> + };
> + };
> +
> + vcc18_ldo1: LDO_REG1 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc18_ldo1";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1800000>;
> + };
> + };
> +
> + vcc33_mipi: LDO_REG2 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc33_mipi";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdd_10: LDO_REG3 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1000000>;
> + regulator-name = "vdd_10";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1000000>;
> + };
> + };
> +
> + vcc18_codec: LDO_REG4 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc18_codec";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1800000>;
> + };
> + };
> +
> + vccio_sd: LDO_REG5 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vccio_sd";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <3300000>;
> + };
> + };
> +
> + vdd10_lcd: LDO_REG6 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1000000>;
> + regulator-name = "vdd10_lcd";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1000000>;
> + };
> + };
> +
> + vcc_18: LDO_REG7 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc_18";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1800000>;
> + };
> + };
> +
> + vcc18_lcd: LDO_REG8 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc18_lcd";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1800000>;
> + };
> + };
> +
> + vcc33_sd: SWITCH_REG1 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-name = "vcc33_sd";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> + };
> +
> + vcc33_lan: SWITCH_REG2 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-name = "vcc33_lan";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> + };
> + };
> + };
> +};
> +
> +&i2c2 {
> + status = "okay";
> +};
> +
> +&i2c5 {
> + status = "okay";
> +};
> +
> +&i2s {
> + #sound-dai-cells = <0>;
> + status = "okay";
> +};
> +&vopb {
> + status = "okay";
> +};
> +
> +&vopb_mmu {
> + status = "okay";
> +};
> +
> +&vopl {
> + status = "okay";
> + /* Don't use vopl for HDMI */
> + vopl_out: port {
> + /delete-node/ endpoint@0;
> + };
same here
> +};
> +
^ permalink raw reply [flat|nested] 26+ messages in thread* [PATCH V2 2/2] ARM: dts: rockchip: add dts for RK3288-Tinker board
@ 2017-02-08 23:07 ` Heiko Stuebner
0 siblings, 0 replies; 26+ messages in thread
From: Heiko Stuebner @ 2017-02-08 23:07 UTC (permalink / raw)
To: linux-arm-kernel
Hi Eddie
Am Montag, 6. Februar 2017, 10:14:47 CET schrieb Eddie Cai:
> This patch add basic support for RK3288-Tinker board. We can boot in to
> rootfs with this patch.
>
> Signed-off-by: Eddie Cai <eddie.cai@rock-chips.com>
> ---
[...]
> +&hdmi {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + #sound-dai-cells = <0>;
why are these needed. More importantly if they are needed, they should be in
rk3288.dtsi instead and not here.
> + ddc-i2c-bus = <&i2c5>;
> + status = "okay";
> + /* Don't use vopl for HDMI */
> + ports {
> + hdmi_in: port {
> + /delete-node/ endpoint at 1;
> + };
> + };
See comment in previous iteration, about the link to vopl being there in
hardware and not wanting to use it for hdmi being a driver issue.
No working around driver issues in the devicetree, so leave the vop <-> hdmi
links intact please :-)
> +};
> +
> +&i2c0 {
> + status = "okay";
> + clock-frequency = <400000>;
> +
> + rk808: pmic at 1b {
> + compatible = "rockchip,rk808";
> + reg = <0x1b>;
> + interrupt-parent = <&gpio0>;
> + interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pmic_int &global_pwroff &dvs_1 &dvs_2>;
> + dvs-gpios = <&gpio0 11 GPIO_ACTIVE_HIGH>,
> + <&gpio0 12 GPIO_ACTIVE_HIGH>;
> +
> + rockchip,system-power-controller;
> + wakeup-source;
> + #clock-cells = <1>;
> + clock-output-names = "xin32k", "rk808-clkout2";
> +
> + vcc1-supply = <&vcc_sys>;
> + vcc2-supply = <&vcc_sys>;
> + vcc3-supply = <&vcc_sys>;
> + vcc4-supply = <&vcc_sys>;
> + vcc6-supply = <&vcc_sys>;
> + vcc7-supply = <&vcc_sys>;
> + vcc8-supply = <&vcc_io>;
> + vcc9-supply = <&vcc_io>;
> + vcc10-supply = <&vcc_io>;
> + vcc11-supply = <&vcc_sys>;
> + vcc12-supply = <&vcc_io>;
> + vddio-supply = <&vcc_io>;
> +
> + regulators {
> + vdd_cpu: DCDC_REG1 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <750000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-name = "vdd_arm";
> + regulator-ramp-delay = <6000>;
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdd_gpu: DCDC_REG2 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <850000>;
> + regulator-max-microvolt = <1250000>;
> + regulator-name = "vdd_gpu";
> + regulator-ramp-delay = <6000>;
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1000000>;
> + };
> + };
> +
> + vcc_ddr: DCDC_REG3 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-name = "vcc_ddr";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> + };
> +
> + vcc_io: DCDC_REG4 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc_io";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <3300000>;
> + };
> + };
> +
> + vcc18_ldo1: LDO_REG1 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc18_ldo1";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1800000>;
> + };
> + };
> +
> + vcc33_mipi: LDO_REG2 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc33_mipi";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdd_10: LDO_REG3 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1000000>;
> + regulator-name = "vdd_10";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1000000>;
> + };
> + };
> +
> + vcc18_codec: LDO_REG4 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc18_codec";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1800000>;
> + };
> + };
> +
> + vccio_sd: LDO_REG5 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vccio_sd";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <3300000>;
> + };
> + };
> +
> + vdd10_lcd: LDO_REG6 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1000000>;
> + regulator-name = "vdd10_lcd";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1000000>;
> + };
> + };
> +
> + vcc_18: LDO_REG7 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc_18";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1800000>;
> + };
> + };
> +
> + vcc18_lcd: LDO_REG8 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc18_lcd";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1800000>;
> + };
> + };
> +
> + vcc33_sd: SWITCH_REG1 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-name = "vcc33_sd";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> + };
> +
> + vcc33_lan: SWITCH_REG2 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-name = "vcc33_lan";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> + };
> + };
> + };
> +};
> +
> +&i2c2 {
> + status = "okay";
> +};
> +
> +&i2c5 {
> + status = "okay";
> +};
> +
> +&i2s {
> + #sound-dai-cells = <0>;
> + status = "okay";
> +};
> +&vopb {
> + status = "okay";
> +};
> +
> +&vopb_mmu {
> + status = "okay";
> +};
> +
> +&vopl {
> + status = "okay";
> + /* Don't use vopl for HDMI */
> + vopl_out: port {
> + /delete-node/ endpoint at 0;
> + };
same here
> +};
> +
^ permalink raw reply [flat|nested] 26+ messages in thread* Re: [PATCH V2 2/2] ARM: dts: rockchip: add dts for RK3288-Tinker board
2017-02-08 23:07 ` Heiko Stuebner
(?)
@ 2017-02-14 9:54 ` Eddie Cai
-1 siblings, 0 replies; 26+ messages in thread
From: Eddie Cai @ 2017-02-14 9:54 UTC (permalink / raw)
To: Heiko Stuebner
Cc: mark.rutland, devicetree, linux, linux-kernel, linux-rockchip,
robh+dt, Eddie Cai, linux-arm-kernel
Hi
2017-02-09 7:07 GMT+08:00 Heiko Stuebner <heiko@sntech.de>:
> Hi Eddie
>
> Am Montag, 6. Februar 2017, 10:14:47 CET schrieb Eddie Cai:
>> This patch add basic support for RK3288-Tinker board. We can boot in to
>> rootfs with this patch.
>>
>> Signed-off-by: Eddie Cai <eddie.cai@rock-chips.com>
>> ---
>
> [...]
>
>> +&hdmi {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + #sound-dai-cells = <0>;
>
> why are these needed. More importantly if they are needed, they should be in
> rk3288.dtsi instead and not here.
I will remove it in next version
>
>
>> + ddc-i2c-bus = <&i2c5>;
>> + status = "okay";
>> + /* Don't use vopl for HDMI */
>> + ports {
>> + hdmi_in: port {
>> + /delete-node/ endpoint@1;
>> + };
>> + };
>
> See comment in previous iteration, about the link to vopl being there in
> hardware and not wanting to use it for hdmi being a driver issue.
> No working around driver issues in the devicetree, so leave the vop <-> hdmi
> links intact please :-)
Sorry, Lost this comment. I will remove it in next version
>
>> +};
>> +
>> +&i2c0 {
>> + status = "okay";
>> + clock-frequency = <400000>;
>> +
>> + rk808: pmic@1b {
>> + compatible = "rockchip,rk808";
>> + reg = <0x1b>;
>> + interrupt-parent = <&gpio0>;
>> + interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pmic_int &global_pwroff &dvs_1 &dvs_2>;
>> + dvs-gpios = <&gpio0 11 GPIO_ACTIVE_HIGH>,
>> + <&gpio0 12 GPIO_ACTIVE_HIGH>;
>> +
>> + rockchip,system-power-controller;
>> + wakeup-source;
>> + #clock-cells = <1>;
>> + clock-output-names = "xin32k", "rk808-clkout2";
>> +
>> + vcc1-supply = <&vcc_sys>;
>> + vcc2-supply = <&vcc_sys>;
>> + vcc3-supply = <&vcc_sys>;
>> + vcc4-supply = <&vcc_sys>;
>> + vcc6-supply = <&vcc_sys>;
>> + vcc7-supply = <&vcc_sys>;
>> + vcc8-supply = <&vcc_io>;
>> + vcc9-supply = <&vcc_io>;
>> + vcc10-supply = <&vcc_io>;
>> + vcc11-supply = <&vcc_sys>;
>> + vcc12-supply = <&vcc_io>;
>> + vddio-supply = <&vcc_io>;
>> +
>> + regulators {
>> + vdd_cpu: DCDC_REG1 {
>> + regulator-always-on;
>> + regulator-boot-on;
>> + regulator-min-microvolt = <750000>;
>> + regulator-max-microvolt = <1350000>;
>> + regulator-name = "vdd_arm";
>> + regulator-ramp-delay = <6000>;
>> + regulator-state-mem {
>> + regulator-off-in-suspend;
>> + };
>> + };
>> +
>> + vdd_gpu: DCDC_REG2 {
>> + regulator-always-on;
>> + regulator-boot-on;
>> + regulator-min-microvolt = <850000>;
>> + regulator-max-microvolt = <1250000>;
>> + regulator-name = "vdd_gpu";
>> + regulator-ramp-delay = <6000>;
>> + regulator-state-mem {
>> + regulator-on-in-suspend;
>> + regulator-suspend-microvolt = <1000000>;
>> + };
>> + };
>> +
>> + vcc_ddr: DCDC_REG3 {
>> + regulator-always-on;
>> + regulator-boot-on;
>> + regulator-name = "vcc_ddr";
>> + regulator-state-mem {
>> + regulator-on-in-suspend;
>> + };
>> + };
>> +
>> + vcc_io: DCDC_REG4 {
>> + regulator-always-on;
>> + regulator-boot-on;
>> + regulator-min-microvolt = <3300000>;
>> + regulator-max-microvolt = <3300000>;
>> + regulator-name = "vcc_io";
>> + regulator-state-mem {
>> + regulator-on-in-suspend;
>> + regulator-suspend-microvolt = <3300000>;
>> + };
>> + };
>> +
>> + vcc18_ldo1: LDO_REG1 {
>> + regulator-always-on;
>> + regulator-boot-on;
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + regulator-name = "vcc18_ldo1";
>> + regulator-state-mem {
>> + regulator-on-in-suspend;
>> + regulator-suspend-microvolt = <1800000>;
>> + };
>> + };
>> +
>> + vcc33_mipi: LDO_REG2 {
>> + regulator-always-on;
>> + regulator-boot-on;
>> + regulator-min-microvolt = <3300000>;
>> + regulator-max-microvolt = <3300000>;
>> + regulator-name = "vcc33_mipi";
>> + regulator-state-mem {
>> + regulator-off-in-suspend;
>> + };
>> + };
>> +
>> + vdd_10: LDO_REG3 {
>> + regulator-always-on;
>> + regulator-boot-on;
>> + regulator-min-microvolt = <1000000>;
>> + regulator-max-microvolt = <1000000>;
>> + regulator-name = "vdd_10";
>> + regulator-state-mem {
>> + regulator-on-in-suspend;
>> + regulator-suspend-microvolt = <1000000>;
>> + };
>> + };
>> +
>> + vcc18_codec: LDO_REG4 {
>> + regulator-always-on;
>> + regulator-boot-on;
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + regulator-name = "vcc18_codec";
>> + regulator-state-mem {
>> + regulator-on-in-suspend;
>> + regulator-suspend-microvolt = <1800000>;
>> + };
>> + };
>> +
>> + vccio_sd: LDO_REG5 {
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <3300000>;
>> + regulator-name = "vccio_sd";
>> + regulator-state-mem {
>> + regulator-on-in-suspend;
>> + regulator-suspend-microvolt = <3300000>;
>> + };
>> + };
>> +
>> + vdd10_lcd: LDO_REG6 {
>> + regulator-always-on;
>> + regulator-boot-on;
>> + regulator-min-microvolt = <1000000>;
>> + regulator-max-microvolt = <1000000>;
>> + regulator-name = "vdd10_lcd";
>> + regulator-state-mem {
>> + regulator-on-in-suspend;
>> + regulator-suspend-microvolt = <1000000>;
>> + };
>> + };
>> +
>> + vcc_18: LDO_REG7 {
>> + regulator-always-on;
>> + regulator-boot-on;
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + regulator-name = "vcc_18";
>> + regulator-state-mem {
>> + regulator-on-in-suspend;
>> + regulator-suspend-microvolt = <1800000>;
>> + };
>> + };
>> +
>> + vcc18_lcd: LDO_REG8 {
>> + regulator-always-on;
>> + regulator-boot-on;
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + regulator-name = "vcc18_lcd";
>> + regulator-state-mem {
>> + regulator-on-in-suspend;
>> + regulator-suspend-microvolt = <1800000>;
>> + };
>> + };
>> +
>> + vcc33_sd: SWITCH_REG1 {
>> + regulator-always-on;
>> + regulator-boot-on;
>> + regulator-name = "vcc33_sd";
>> + regulator-state-mem {
>> + regulator-on-in-suspend;
>> + };
>> + };
>> +
>> + vcc33_lan: SWITCH_REG2 {
>> + regulator-always-on;
>> + regulator-boot-on;
>> + regulator-name = "vcc33_lan";
>> + regulator-state-mem {
>> + regulator-on-in-suspend;
>> + };
>> + };
>> + };
>> + };
>> +};
>> +
>> +&i2c2 {
>> + status = "okay";
>> +};
>> +
>> +&i2c5 {
>> + status = "okay";
>> +};
>> +
>> +&i2s {
>> + #sound-dai-cells = <0>;
>> + status = "okay";
>> +};
>> +&vopb {
>> + status = "okay";
>> +};
>> +
>> +&vopb_mmu {
>> + status = "okay";
>> +};
>> +
>> +&vopl {
>> + status = "okay";
>> + /* Don't use vopl for HDMI */
>> + vopl_out: port {
>> + /delete-node/ endpoint@0;
>> + };
>
> same here
I will remove it in next version
>
>> +};
>> +
>
>
^ permalink raw reply [flat|nested] 26+ messages in thread* Re: [PATCH V2 2/2] ARM: dts: rockchip: add dts for RK3288-Tinker board
@ 2017-02-14 9:54 ` Eddie Cai
0 siblings, 0 replies; 26+ messages in thread
From: Eddie Cai @ 2017-02-14 9:54 UTC (permalink / raw)
To: Heiko Stuebner
Cc: robh+dt, mark.rutland, linux, devicetree, linux-arm-kernel,
linux-rockchip, linux-kernel, Eddie Cai
Hi
2017-02-09 7:07 GMT+08:00 Heiko Stuebner <heiko@sntech.de>:
> Hi Eddie
>
> Am Montag, 6. Februar 2017, 10:14:47 CET schrieb Eddie Cai:
>> This patch add basic support for RK3288-Tinker board. We can boot in to
>> rootfs with this patch.
>>
>> Signed-off-by: Eddie Cai <eddie.cai@rock-chips.com>
>> ---
>
> [...]
>
>> +&hdmi {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + #sound-dai-cells = <0>;
>
> why are these needed. More importantly if they are needed, they should be in
> rk3288.dtsi instead and not here.
I will remove it in next version
>
>
>> + ddc-i2c-bus = <&i2c5>;
>> + status = "okay";
>> + /* Don't use vopl for HDMI */
>> + ports {
>> + hdmi_in: port {
>> + /delete-node/ endpoint@1;
>> + };
>> + };
>
> See comment in previous iteration, about the link to vopl being there in
> hardware and not wanting to use it for hdmi being a driver issue.
> No working around driver issues in the devicetree, so leave the vop <-> hdmi
> links intact please :-)
Sorry, Lost this comment. I will remove it in next version
>
>> +};
>> +
>> +&i2c0 {
>> + status = "okay";
>> + clock-frequency = <400000>;
>> +
>> + rk808: pmic@1b {
>> + compatible = "rockchip,rk808";
>> + reg = <0x1b>;
>> + interrupt-parent = <&gpio0>;
>> + interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pmic_int &global_pwroff &dvs_1 &dvs_2>;
>> + dvs-gpios = <&gpio0 11 GPIO_ACTIVE_HIGH>,
>> + <&gpio0 12 GPIO_ACTIVE_HIGH>;
>> +
>> + rockchip,system-power-controller;
>> + wakeup-source;
>> + #clock-cells = <1>;
>> + clock-output-names = "xin32k", "rk808-clkout2";
>> +
>> + vcc1-supply = <&vcc_sys>;
>> + vcc2-supply = <&vcc_sys>;
>> + vcc3-supply = <&vcc_sys>;
>> + vcc4-supply = <&vcc_sys>;
>> + vcc6-supply = <&vcc_sys>;
>> + vcc7-supply = <&vcc_sys>;
>> + vcc8-supply = <&vcc_io>;
>> + vcc9-supply = <&vcc_io>;
>> + vcc10-supply = <&vcc_io>;
>> + vcc11-supply = <&vcc_sys>;
>> + vcc12-supply = <&vcc_io>;
>> + vddio-supply = <&vcc_io>;
>> +
>> + regulators {
>> + vdd_cpu: DCDC_REG1 {
>> + regulator-always-on;
>> + regulator-boot-on;
>> + regulator-min-microvolt = <750000>;
>> + regulator-max-microvolt = <1350000>;
>> + regulator-name = "vdd_arm";
>> + regulator-ramp-delay = <6000>;
>> + regulator-state-mem {
>> + regulator-off-in-suspend;
>> + };
>> + };
>> +
>> + vdd_gpu: DCDC_REG2 {
>> + regulator-always-on;
>> + regulator-boot-on;
>> + regulator-min-microvolt = <850000>;
>> + regulator-max-microvolt = <1250000>;
>> + regulator-name = "vdd_gpu";
>> + regulator-ramp-delay = <6000>;
>> + regulator-state-mem {
>> + regulator-on-in-suspend;
>> + regulator-suspend-microvolt = <1000000>;
>> + };
>> + };
>> +
>> + vcc_ddr: DCDC_REG3 {
>> + regulator-always-on;
>> + regulator-boot-on;
>> + regulator-name = "vcc_ddr";
>> + regulator-state-mem {
>> + regulator-on-in-suspend;
>> + };
>> + };
>> +
>> + vcc_io: DCDC_REG4 {
>> + regulator-always-on;
>> + regulator-boot-on;
>> + regulator-min-microvolt = <3300000>;
>> + regulator-max-microvolt = <3300000>;
>> + regulator-name = "vcc_io";
>> + regulator-state-mem {
>> + regulator-on-in-suspend;
>> + regulator-suspend-microvolt = <3300000>;
>> + };
>> + };
>> +
>> + vcc18_ldo1: LDO_REG1 {
>> + regulator-always-on;
>> + regulator-boot-on;
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + regulator-name = "vcc18_ldo1";
>> + regulator-state-mem {
>> + regulator-on-in-suspend;
>> + regulator-suspend-microvolt = <1800000>;
>> + };
>> + };
>> +
>> + vcc33_mipi: LDO_REG2 {
>> + regulator-always-on;
>> + regulator-boot-on;
>> + regulator-min-microvolt = <3300000>;
>> + regulator-max-microvolt = <3300000>;
>> + regulator-name = "vcc33_mipi";
>> + regulator-state-mem {
>> + regulator-off-in-suspend;
>> + };
>> + };
>> +
>> + vdd_10: LDO_REG3 {
>> + regulator-always-on;
>> + regulator-boot-on;
>> + regulator-min-microvolt = <1000000>;
>> + regulator-max-microvolt = <1000000>;
>> + regulator-name = "vdd_10";
>> + regulator-state-mem {
>> + regulator-on-in-suspend;
>> + regulator-suspend-microvolt = <1000000>;
>> + };
>> + };
>> +
>> + vcc18_codec: LDO_REG4 {
>> + regulator-always-on;
>> + regulator-boot-on;
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + regulator-name = "vcc18_codec";
>> + regulator-state-mem {
>> + regulator-on-in-suspend;
>> + regulator-suspend-microvolt = <1800000>;
>> + };
>> + };
>> +
>> + vccio_sd: LDO_REG5 {
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <3300000>;
>> + regulator-name = "vccio_sd";
>> + regulator-state-mem {
>> + regulator-on-in-suspend;
>> + regulator-suspend-microvolt = <3300000>;
>> + };
>> + };
>> +
>> + vdd10_lcd: LDO_REG6 {
>> + regulator-always-on;
>> + regulator-boot-on;
>> + regulator-min-microvolt = <1000000>;
>> + regulator-max-microvolt = <1000000>;
>> + regulator-name = "vdd10_lcd";
>> + regulator-state-mem {
>> + regulator-on-in-suspend;
>> + regulator-suspend-microvolt = <1000000>;
>> + };
>> + };
>> +
>> + vcc_18: LDO_REG7 {
>> + regulator-always-on;
>> + regulator-boot-on;
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + regulator-name = "vcc_18";
>> + regulator-state-mem {
>> + regulator-on-in-suspend;
>> + regulator-suspend-microvolt = <1800000>;
>> + };
>> + };
>> +
>> + vcc18_lcd: LDO_REG8 {
>> + regulator-always-on;
>> + regulator-boot-on;
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + regulator-name = "vcc18_lcd";
>> + regulator-state-mem {
>> + regulator-on-in-suspend;
>> + regulator-suspend-microvolt = <1800000>;
>> + };
>> + };
>> +
>> + vcc33_sd: SWITCH_REG1 {
>> + regulator-always-on;
>> + regulator-boot-on;
>> + regulator-name = "vcc33_sd";
>> + regulator-state-mem {
>> + regulator-on-in-suspend;
>> + };
>> + };
>> +
>> + vcc33_lan: SWITCH_REG2 {
>> + regulator-always-on;
>> + regulator-boot-on;
>> + regulator-name = "vcc33_lan";
>> + regulator-state-mem {
>> + regulator-on-in-suspend;
>> + };
>> + };
>> + };
>> + };
>> +};
>> +
>> +&i2c2 {
>> + status = "okay";
>> +};
>> +
>> +&i2c5 {
>> + status = "okay";
>> +};
>> +
>> +&i2s {
>> + #sound-dai-cells = <0>;
>> + status = "okay";
>> +};
>> +&vopb {
>> + status = "okay";
>> +};
>> +
>> +&vopb_mmu {
>> + status = "okay";
>> +};
>> +
>> +&vopl {
>> + status = "okay";
>> + /* Don't use vopl for HDMI */
>> + vopl_out: port {
>> + /delete-node/ endpoint@0;
>> + };
>
> same here
I will remove it in next version
>
>> +};
>> +
>
>
^ permalink raw reply [flat|nested] 26+ messages in thread* [PATCH V2 2/2] ARM: dts: rockchip: add dts for RK3288-Tinker board
@ 2017-02-14 9:54 ` Eddie Cai
0 siblings, 0 replies; 26+ messages in thread
From: Eddie Cai @ 2017-02-14 9:54 UTC (permalink / raw)
To: linux-arm-kernel
Hi
2017-02-09 7:07 GMT+08:00 Heiko Stuebner <heiko@sntech.de>:
> Hi Eddie
>
> Am Montag, 6. Februar 2017, 10:14:47 CET schrieb Eddie Cai:
>> This patch add basic support for RK3288-Tinker board. We can boot in to
>> rootfs with this patch.
>>
>> Signed-off-by: Eddie Cai <eddie.cai@rock-chips.com>
>> ---
>
> [...]
>
>> +&hdmi {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + #sound-dai-cells = <0>;
>
> why are these needed. More importantly if they are needed, they should be in
> rk3288.dtsi instead and not here.
I will remove it in next version
>
>
>> + ddc-i2c-bus = <&i2c5>;
>> + status = "okay";
>> + /* Don't use vopl for HDMI */
>> + ports {
>> + hdmi_in: port {
>> + /delete-node/ endpoint at 1;
>> + };
>> + };
>
> See comment in previous iteration, about the link to vopl being there in
> hardware and not wanting to use it for hdmi being a driver issue.
> No working around driver issues in the devicetree, so leave the vop <-> hdmi
> links intact please :-)
Sorry, Lost this comment. I will remove it in next version
>
>> +};
>> +
>> +&i2c0 {
>> + status = "okay";
>> + clock-frequency = <400000>;
>> +
>> + rk808: pmic at 1b {
>> + compatible = "rockchip,rk808";
>> + reg = <0x1b>;
>> + interrupt-parent = <&gpio0>;
>> + interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pmic_int &global_pwroff &dvs_1 &dvs_2>;
>> + dvs-gpios = <&gpio0 11 GPIO_ACTIVE_HIGH>,
>> + <&gpio0 12 GPIO_ACTIVE_HIGH>;
>> +
>> + rockchip,system-power-controller;
>> + wakeup-source;
>> + #clock-cells = <1>;
>> + clock-output-names = "xin32k", "rk808-clkout2";
>> +
>> + vcc1-supply = <&vcc_sys>;
>> + vcc2-supply = <&vcc_sys>;
>> + vcc3-supply = <&vcc_sys>;
>> + vcc4-supply = <&vcc_sys>;
>> + vcc6-supply = <&vcc_sys>;
>> + vcc7-supply = <&vcc_sys>;
>> + vcc8-supply = <&vcc_io>;
>> + vcc9-supply = <&vcc_io>;
>> + vcc10-supply = <&vcc_io>;
>> + vcc11-supply = <&vcc_sys>;
>> + vcc12-supply = <&vcc_io>;
>> + vddio-supply = <&vcc_io>;
>> +
>> + regulators {
>> + vdd_cpu: DCDC_REG1 {
>> + regulator-always-on;
>> + regulator-boot-on;
>> + regulator-min-microvolt = <750000>;
>> + regulator-max-microvolt = <1350000>;
>> + regulator-name = "vdd_arm";
>> + regulator-ramp-delay = <6000>;
>> + regulator-state-mem {
>> + regulator-off-in-suspend;
>> + };
>> + };
>> +
>> + vdd_gpu: DCDC_REG2 {
>> + regulator-always-on;
>> + regulator-boot-on;
>> + regulator-min-microvolt = <850000>;
>> + regulator-max-microvolt = <1250000>;
>> + regulator-name = "vdd_gpu";
>> + regulator-ramp-delay = <6000>;
>> + regulator-state-mem {
>> + regulator-on-in-suspend;
>> + regulator-suspend-microvolt = <1000000>;
>> + };
>> + };
>> +
>> + vcc_ddr: DCDC_REG3 {
>> + regulator-always-on;
>> + regulator-boot-on;
>> + regulator-name = "vcc_ddr";
>> + regulator-state-mem {
>> + regulator-on-in-suspend;
>> + };
>> + };
>> +
>> + vcc_io: DCDC_REG4 {
>> + regulator-always-on;
>> + regulator-boot-on;
>> + regulator-min-microvolt = <3300000>;
>> + regulator-max-microvolt = <3300000>;
>> + regulator-name = "vcc_io";
>> + regulator-state-mem {
>> + regulator-on-in-suspend;
>> + regulator-suspend-microvolt = <3300000>;
>> + };
>> + };
>> +
>> + vcc18_ldo1: LDO_REG1 {
>> + regulator-always-on;
>> + regulator-boot-on;
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + regulator-name = "vcc18_ldo1";
>> + regulator-state-mem {
>> + regulator-on-in-suspend;
>> + regulator-suspend-microvolt = <1800000>;
>> + };
>> + };
>> +
>> + vcc33_mipi: LDO_REG2 {
>> + regulator-always-on;
>> + regulator-boot-on;
>> + regulator-min-microvolt = <3300000>;
>> + regulator-max-microvolt = <3300000>;
>> + regulator-name = "vcc33_mipi";
>> + regulator-state-mem {
>> + regulator-off-in-suspend;
>> + };
>> + };
>> +
>> + vdd_10: LDO_REG3 {
>> + regulator-always-on;
>> + regulator-boot-on;
>> + regulator-min-microvolt = <1000000>;
>> + regulator-max-microvolt = <1000000>;
>> + regulator-name = "vdd_10";
>> + regulator-state-mem {
>> + regulator-on-in-suspend;
>> + regulator-suspend-microvolt = <1000000>;
>> + };
>> + };
>> +
>> + vcc18_codec: LDO_REG4 {
>> + regulator-always-on;
>> + regulator-boot-on;
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + regulator-name = "vcc18_codec";
>> + regulator-state-mem {
>> + regulator-on-in-suspend;
>> + regulator-suspend-microvolt = <1800000>;
>> + };
>> + };
>> +
>> + vccio_sd: LDO_REG5 {
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <3300000>;
>> + regulator-name = "vccio_sd";
>> + regulator-state-mem {
>> + regulator-on-in-suspend;
>> + regulator-suspend-microvolt = <3300000>;
>> + };
>> + };
>> +
>> + vdd10_lcd: LDO_REG6 {
>> + regulator-always-on;
>> + regulator-boot-on;
>> + regulator-min-microvolt = <1000000>;
>> + regulator-max-microvolt = <1000000>;
>> + regulator-name = "vdd10_lcd";
>> + regulator-state-mem {
>> + regulator-on-in-suspend;
>> + regulator-suspend-microvolt = <1000000>;
>> + };
>> + };
>> +
>> + vcc_18: LDO_REG7 {
>> + regulator-always-on;
>> + regulator-boot-on;
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + regulator-name = "vcc_18";
>> + regulator-state-mem {
>> + regulator-on-in-suspend;
>> + regulator-suspend-microvolt = <1800000>;
>> + };
>> + };
>> +
>> + vcc18_lcd: LDO_REG8 {
>> + regulator-always-on;
>> + regulator-boot-on;
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + regulator-name = "vcc18_lcd";
>> + regulator-state-mem {
>> + regulator-on-in-suspend;
>> + regulator-suspend-microvolt = <1800000>;
>> + };
>> + };
>> +
>> + vcc33_sd: SWITCH_REG1 {
>> + regulator-always-on;
>> + regulator-boot-on;
>> + regulator-name = "vcc33_sd";
>> + regulator-state-mem {
>> + regulator-on-in-suspend;
>> + };
>> + };
>> +
>> + vcc33_lan: SWITCH_REG2 {
>> + regulator-always-on;
>> + regulator-boot-on;
>> + regulator-name = "vcc33_lan";
>> + regulator-state-mem {
>> + regulator-on-in-suspend;
>> + };
>> + };
>> + };
>> + };
>> +};
>> +
>> +&i2c2 {
>> + status = "okay";
>> +};
>> +
>> +&i2c5 {
>> + status = "okay";
>> +};
>> +
>> +&i2s {
>> + #sound-dai-cells = <0>;
>> + status = "okay";
>> +};
>> +&vopb {
>> + status = "okay";
>> +};
>> +
>> +&vopb_mmu {
>> + status = "okay";
>> +};
>> +
>> +&vopl {
>> + status = "okay";
>> + /* Don't use vopl for HDMI */
>> + vopl_out: port {
>> + /delete-node/ endpoint at 0;
>> + };
>
> same here
I will remove it in next version
>
>> +};
>> +
>
>
^ permalink raw reply [flat|nested] 26+ messages in thread
[parent not found: <1486347287-31051-3-git-send-email-eddie.cai-TNX95d0MmH7DzftRWevZcw@public.gmane.org>]
* Re: [PATCH V2 2/2] ARM: dts: rockchip: add dts for RK3288-Tinker board
2017-02-06 2:14 ` Eddie Cai
(?)
@ 2017-02-06 2:54 ` Andrew Lunn
-1 siblings, 0 replies; 26+ messages in thread
From: Andrew Lunn @ 2017-02-06 2:54 UTC (permalink / raw)
To: Eddie Cai
Cc: robh+dt-DgEjT+Ai2ygdnm+yROfE0A, mark.rutland-5wv7dgnIgG8,
heiko-4mtYJXux2i+zQB+pC5nmwQ, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-kernel-u79uwXL29TY76Z2rM5mHXA, linux-I+IVW8TIWO2tmTQ+vhA3Yw,
linux-rockchip-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
eddie.cai-TNX95d0MmH7DzftRWevZcw,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r
Hi Eddie
> + button@0 {
> + gpios = <&gpio0 5 GPIO_ACTIVE_LOW>;
> + linux,code = <116>;
It is a good idea to use include/dt-bindings/input/input.h
and then you can replace <116> with < KEY_POWER > which is more
readable.
> + label = "GPIO Key Power";
> + linux,input-type = <1>;
< EV_KEY >
> + gpio-key,wakeup = <1>;
This has been replace with wakeup-source.
> + debounce-interval = <100>;
> + };
> + };
Andrew
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 26+ messages in thread* Re: [PATCH V2 2/2] ARM: dts: rockchip: add dts for RK3288-Tinker board
@ 2017-02-06 2:54 ` Andrew Lunn
0 siblings, 0 replies; 26+ messages in thread
From: Andrew Lunn @ 2017-02-06 2:54 UTC (permalink / raw)
To: Eddie Cai
Cc: robh+dt, mark.rutland, heiko, devicetree, linux-kernel, linux,
linux-rockchip, eddie.cai, linux-arm-kernel
Hi Eddie
> + button@0 {
> + gpios = <&gpio0 5 GPIO_ACTIVE_LOW>;
> + linux,code = <116>;
It is a good idea to use include/dt-bindings/input/input.h
and then you can replace <116> with < KEY_POWER > which is more
readable.
> + label = "GPIO Key Power";
> + linux,input-type = <1>;
< EV_KEY >
> + gpio-key,wakeup = <1>;
This has been replace with wakeup-source.
> + debounce-interval = <100>;
> + };
> + };
Andrew
^ permalink raw reply [flat|nested] 26+ messages in thread* [PATCH V2 2/2] ARM: dts: rockchip: add dts for RK3288-Tinker board
@ 2017-02-06 2:54 ` Andrew Lunn
0 siblings, 0 replies; 26+ messages in thread
From: Andrew Lunn @ 2017-02-06 2:54 UTC (permalink / raw)
To: linux-arm-kernel
Hi Eddie
> + button at 0 {
> + gpios = <&gpio0 5 GPIO_ACTIVE_LOW>;
> + linux,code = <116>;
It is a good idea to use include/dt-bindings/input/input.h
and then you can replace <116> with < KEY_POWER > which is more
readable.
> + label = "GPIO Key Power";
> + linux,input-type = <1>;
< EV_KEY >
> + gpio-key,wakeup = <1>;
This has been replace with wakeup-source.
> + debounce-interval = <100>;
> + };
> + };
Andrew
^ permalink raw reply [flat|nested] 26+ messages in thread[parent not found: <20170206025435.GA32506-g2DYL2Zd6BY@public.gmane.org>]
* Re: [PATCH V2 2/2] ARM: dts: rockchip: add dts for RK3288-Tinker board
2017-02-06 2:54 ` Andrew Lunn
(?)
@ 2017-02-06 5:52 ` Eddie Cai
-1 siblings, 0 replies; 26+ messages in thread
From: Eddie Cai @ 2017-02-06 5:52 UTC (permalink / raw)
To: Andrew Lunn
Cc: robh+dt-DgEjT+Ai2ygdnm+yROfE0A, mark.rutland-5wv7dgnIgG8,
Heiko Stuebner, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-kernel-u79uwXL29TY76Z2rM5mHXA, linux-I+IVW8TIWO2tmTQ+vhA3Yw,
linux-rockchip-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, Eddie Cai,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r
Hi Andrew
2017-02-06 10:54 GMT+08:00 Andrew Lunn <andrew-g2DYL2Zd6BY@public.gmane.org>:
> Hi Eddie
>
>> + button@0 {
>> + gpios = <&gpio0 5 GPIO_ACTIVE_LOW>;
>> + linux,code = <116>;
>
> It is a good idea to use include/dt-bindings/input/input.h
>
> and then you can replace <116> with < KEY_POWER > which is more
> readable.
Thanks, I will modify it in next version.
>
>> + label = "GPIO Key Power";
>> + linux,input-type = <1>;
>
> < EV_KEY >
>
>> + gpio-key,wakeup = <1>;
>
> This has been replace with wakeup-source.
Thanks, I will modify it in next version
>
>> + debounce-interval = <100>;
>> + };
>> + };
>
> Andrew
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 26+ messages in thread* Re: [PATCH V2 2/2] ARM: dts: rockchip: add dts for RK3288-Tinker board
@ 2017-02-06 5:52 ` Eddie Cai
0 siblings, 0 replies; 26+ messages in thread
From: Eddie Cai @ 2017-02-06 5:52 UTC (permalink / raw)
To: Andrew Lunn
Cc: robh+dt, mark.rutland, Heiko Stuebner, devicetree, linux-kernel,
linux, linux-rockchip, Eddie Cai, linux-arm-kernel
Hi Andrew
2017-02-06 10:54 GMT+08:00 Andrew Lunn <andrew@lunn.ch>:
> Hi Eddie
>
>> + button@0 {
>> + gpios = <&gpio0 5 GPIO_ACTIVE_LOW>;
>> + linux,code = <116>;
>
> It is a good idea to use include/dt-bindings/input/input.h
>
> and then you can replace <116> with < KEY_POWER > which is more
> readable.
Thanks, I will modify it in next version.
>
>> + label = "GPIO Key Power";
>> + linux,input-type = <1>;
>
> < EV_KEY >
>
>> + gpio-key,wakeup = <1>;
>
> This has been replace with wakeup-source.
Thanks, I will modify it in next version
>
>> + debounce-interval = <100>;
>> + };
>> + };
>
> Andrew
^ permalink raw reply [flat|nested] 26+ messages in thread* [PATCH V2 2/2] ARM: dts: rockchip: add dts for RK3288-Tinker board
@ 2017-02-06 5:52 ` Eddie Cai
0 siblings, 0 replies; 26+ messages in thread
From: Eddie Cai @ 2017-02-06 5:52 UTC (permalink / raw)
To: linux-arm-kernel
Hi Andrew
2017-02-06 10:54 GMT+08:00 Andrew Lunn <andrew@lunn.ch>:
> Hi Eddie
>
>> + button at 0 {
>> + gpios = <&gpio0 5 GPIO_ACTIVE_LOW>;
>> + linux,code = <116>;
>
> It is a good idea to use include/dt-bindings/input/input.h
>
> and then you can replace <116> with < KEY_POWER > which is more
> readable.
Thanks, I will modify it in next version.
>
>> + label = "GPIO Key Power";
>> + linux,input-type = <1>;
>
> < EV_KEY >
>
>> + gpio-key,wakeup = <1>;
>
> This has been replace with wakeup-source.
Thanks, I will modify it in next version
>
>> + debounce-interval = <100>;
>> + };
>> + };
>
> Andrew
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH V2 2/2] ARM: dts: rockchip: add dts for RK3288-Tinker board
2017-02-06 2:14 ` Eddie Cai
(?)
@ 2017-02-09 1:45 ` Andy Yan
-1 siblings, 0 replies; 26+ messages in thread
From: Andy Yan @ 2017-02-09 1:45 UTC (permalink / raw)
To: Eddie Cai, robh+dt-DgEjT+Ai2ygdnm+yROfE0A,
mark.rutland-5wv7dgnIgG8, heiko-4mtYJXux2i+zQB+pC5nmwQ
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-kernel-u79uwXL29TY76Z2rM5mHXA, linux-I+IVW8TIWO2tmTQ+vhA3Yw,
linux-rockchip-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
eddie.cai-TNX95d0MmH7DzftRWevZcw,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r
Hi Eddie:
On 2017年02月06日 10:14, Eddie Cai wrote:
> This patch add basic support for RK3288-Tinker board. We can boot in to rootfs
> with this patch.
>
> Signed-off-by: Eddie Cai <eddie.cai@rock-chips.com>
> ---
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/rk3288-tinker.dts | 543 ++++++++++++++++++++++++++++++++++++
> 2 files changed, 544 insertions(+)
> create mode 100644 arch/arm/boot/dts/rk3288-tinker.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 7327250..4fc05b7 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -679,6 +679,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += \
> rk3288-popmetal.dtb \
> rk3288-r89.dtb \
> rk3288-rock2-square.dtb \
> + rk3288-tinker.dtb \
> rk3288-veyron-brain.dtb \
> rk3288-veyron-jaq.dtb \
> rk3288-veyron-jerry.dtb \
> diff --git a/arch/arm/boot/dts/rk3288-tinker.dts b/arch/arm/boot/dts/rk3288-tinker.dts
> new file mode 100644
> index 0000000..c48563e
> --- /dev/null
> +++ b/arch/arm/boot/dts/rk3288-tinker.dts
> @@ -0,0 +1,543 @@
> +/*
> + * Copyright (c) 2017 Fuzhou Rockchip Electronics Co., Ltd.
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This file is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of the
> + * License, or (at your option) any later version.
> + *
> + * This file is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use,
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +/dts-v1/;
> +
> +#include "rk3288.dtsi"
> +
> +/ {
> + model = "Rockchip RK3288 Tinker Board";
> + compatible = "asus,rk3288-tinker", "rockchip,rk3288";
> +
> + memory {
> + reg = <0x0 0x80000000>;
> + device_type = "memory";
> + };
> +
> + ext_gmac: external-gmac-clock {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <125000000>;
> + clock-output-names = "ext_gmac";
> + };
> +
> + gpio-keys {
> + compatible = "gpio-keys";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + autorepeat;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&pwrbtn>;
> +
> + button@0 {
> + gpios = <&gpio0 5 GPIO_ACTIVE_LOW>;
It's better to describe gpios like: gpios = <&gpio0 RK_PA5
GPIO_ACTIVE_LOW>
see: [0]
[0] https://patchwork.kernel.org/patch/9390693/
> + linux,code = <116>;
> + label = "GPIO Key Power";
> + linux,input-type = <1>;
> + gpio-key,wakeup = <1>;
> + debounce-interval = <100>;
> + };
> + };
> +
> + gpio-leds {
> + compatible = "gpio-leds";
> +
> + pwr-led {
> + gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "default-on";
> + };
> +
> + act-led {
> + gpios=<&gpio2 3 GPIO_ACTIVE_LOW>;
> + linux,default-trigger="mmc0";
> + };
> + };
> +
> + sound {
> + compatible = "simple-audio-card";
> + simple-audio-card,format = "i2s";
> + simple-audio-card,name = "rockchip,tinker-codec";
> + simple-audio-card,mclk-fs = <512>;
> + simple-audio-card,cpu {
> + sound-dai = <&i2s>;
> + };
> + simple-audio-card,codec {
> + sound-dai = <&hdmi>;
> + };
> + };
> +
> + vcc_sys: vsys-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc_sys";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + vcc_sd: sdmmc-regulator {
> + compatible = "regulator-fixed";
> + gpio = <&gpio7 11 GPIO_ACTIVE_LOW>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&sdmmc_pwr>;
> + regulator-name = "vcc_sd";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + startup-delay-us = <100000>;
> + vin-supply = <&vcc_io>;
> + };
> +};
> +
> +&cpu0 {
> + cpu0-supply = <&vdd_cpu>;
> +};
> +
> +&gmac {
> + phy-supply = <&vcc33_lan>;
> + phy-mode = "rgmii";
> + clock_in_out = "input";
> + snps,reset-gpio = <&gpio4 7 0>;
> + snps,reset-active-low;
> + snps,reset-delays-us = <0 10000 1000000>;
> + assigned-clocks = <&cru SCLK_MAC>;
> + assigned-clock-parents = <&ext_gmac>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&rgmii_pins>;
> + tx_delay = <0x30>;
> + rx_delay = <0x10>;
> + status = "ok";
> +};
> +
> +&hdmi {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + #sound-dai-cells = <0>;
> + ddc-i2c-bus = <&i2c5>;
> + status = "okay";
> + /* Don't use vopl for HDMI */
> + ports {
> + hdmi_in: port {
> + /delete-node/ endpoint@1;
> + };
> + };
> +};
> +
> +&i2c0 {
> + status = "okay";
> + clock-frequency = <400000>;
> +
> + rk808: pmic@1b {
> + compatible = "rockchip,rk808";
> + reg = <0x1b>;
> + interrupt-parent = <&gpio0>;
> + interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pmic_int &global_pwroff &dvs_1 &dvs_2>;
> + dvs-gpios = <&gpio0 11 GPIO_ACTIVE_HIGH>,
> + <&gpio0 12 GPIO_ACTIVE_HIGH>;
> +
> + rockchip,system-power-controller;
> + wakeup-source;
> + #clock-cells = <1>;
> + clock-output-names = "xin32k", "rk808-clkout2";
> +
> + vcc1-supply = <&vcc_sys>;
> + vcc2-supply = <&vcc_sys>;
> + vcc3-supply = <&vcc_sys>;
> + vcc4-supply = <&vcc_sys>;
> + vcc6-supply = <&vcc_sys>;
> + vcc7-supply = <&vcc_sys>;
> + vcc8-supply = <&vcc_io>;
> + vcc9-supply = <&vcc_io>;
> + vcc10-supply = <&vcc_io>;
> + vcc11-supply = <&vcc_sys>;
> + vcc12-supply = <&vcc_io>;
> + vddio-supply = <&vcc_io>;
> +
> + regulators {
> + vdd_cpu: DCDC_REG1 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <750000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-name = "vdd_arm";
> + regulator-ramp-delay = <6000>;
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdd_gpu: DCDC_REG2 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <850000>;
> + regulator-max-microvolt = <1250000>;
> + regulator-name = "vdd_gpu";
> + regulator-ramp-delay = <6000>;
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1000000>;
> + };
> + };
> +
> + vcc_ddr: DCDC_REG3 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-name = "vcc_ddr";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> + };
> +
> + vcc_io: DCDC_REG4 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc_io";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <3300000>;
> + };
> + };
> +
> + vcc18_ldo1: LDO_REG1 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc18_ldo1";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1800000>;
> + };
> + };
> +
> + vcc33_mipi: LDO_REG2 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc33_mipi";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdd_10: LDO_REG3 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1000000>;
> + regulator-name = "vdd_10";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1000000>;
> + };
> + };
> +
> + vcc18_codec: LDO_REG4 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc18_codec";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1800000>;
> + };
> + };
> +
> + vccio_sd: LDO_REG5 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vccio_sd";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <3300000>;
> + };
> + };
> +
> + vdd10_lcd: LDO_REG6 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1000000>;
> + regulator-name = "vdd10_lcd";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1000000>;
> + };
> + };
> +
> + vcc_18: LDO_REG7 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc_18";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1800000>;
> + };
> + };
> +
> + vcc18_lcd: LDO_REG8 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc18_lcd";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1800000>;
> + };
> + };
> +
> + vcc33_sd: SWITCH_REG1 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-name = "vcc33_sd";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> + };
> +
> + vcc33_lan: SWITCH_REG2 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-name = "vcc33_lan";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> + };
> + };
> + };
> +};
> +
> +&i2c2 {
> + status = "okay";
> +};
> +
> +&i2c5 {
> + status = "okay";
> +};
> +
> +&i2s {
> + #sound-dai-cells = <0>;
> + status = "okay";
> +};
> +
> +&io_domains {
> + status = "okay";
> +
> + sdcard-supply = <&vccio_sd>;
> +};
> +
> +&pinctrl {
> + pcfg_pull_none_drv_8ma: pcfg-pull-none-drv-8ma {
> + drive-strength = <8>;
> + };
> +
> + pcfg_pull_up_drv_8ma: pcfg-pull-up-drv-8ma {
> + bias-pull-up;
> + drive-strength = <8>;
> + };
> +
> + backlight {
> + bl_en: bl-en {
> + rockchip,pins = <7 2 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + buttons {
> + pwrbtn: pwrbtn {
> + rockchip,pins = <0 5 RK_FUNC_GPIO &pcfg_pull_up>;
> + };
> + };
> +
> + eth_phy {
> + eth_phy_pwr: eth-phy-pwr {
> + rockchip,pins = <0 6 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + pmic {
> + pmic_int: pmic-int {
> + rockchip,pins = <RK_GPIO0 4 RK_FUNC_GPIO \
> + &pcfg_pull_up>;
> + };
> +
> + dvs_1: dvs-1 {
> + rockchip,pins = <RK_GPIO0 11 RK_FUNC_GPIO \
> + &pcfg_pull_down>;
> + };
> +
> + dvs_2: dvs-2 {
> + rockchip,pins = <RK_GPIO0 12 RK_FUNC_GPIO \
> + &pcfg_pull_down>;
> + };
> + };
> +
> + sdmmc {
> + sdmmc_bus4: sdmmc-bus4 {
> + rockchip,pins = <6 16 RK_FUNC_1 &pcfg_pull_up_drv_8ma>,
> + <6 17 RK_FUNC_1 &pcfg_pull_up_drv_8ma>,
> + <6 18 RK_FUNC_1 &pcfg_pull_up_drv_8ma>,
> + <6 19 RK_FUNC_1 &pcfg_pull_up_drv_8ma>;
> + };
> +
> + sdmmc_clk: sdmmc-clk {
> + rockchip,pins = <6 20 RK_FUNC_1 \
> + &pcfg_pull_none_drv_8ma>;
> + };
> +
> + sdmmc_cmd: sdmmc-cmd {
> + rockchip,pins = <6 21 RK_FUNC_1 &pcfg_pull_up_drv_8ma>;
> + };
> +
> + sdmmc_pwr: sdmmc-pwr {
> + rockchip,pins = <7 11 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + usb {
> + host_vbus_drv: host-vbus-drv {
> + rockchip,pins = <0 14 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> +
> + pwr_3g: pwr-3g {
> + rockchip,pins = <7 8 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +};
> +
> +&pwm0 {
> + status = "okay";
> +};
> +
> +&saradc {
> + vref-supply = <&vcc18_ldo1>;
> + status ="okay";
> +};
> +
> +&sdmmc {
> + bus-width = <4>;
> + cap-mmc-highspeed;
> + cap-sd-highspeed;
> + card-detect-delay = <200>;
> + disable-wp; /* wp not hooked up */
> + num-slots = <1>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_bus4>;
> + status = "okay";
> + vmmc-supply = <&vcc33_sd>;
> + vqmmc-supply = <&vccio_sd>;
> +};
> +
> +&tsadc {
> + rockchip,hw-tshut-mode = <1>; /* tshut mode 0:CRU 1:GPIO */
> + rockchip,hw-tshut-polarity = <1>; /* tshut polarity 0:LOW 1:HIGH */
> + status = "okay";
> +};
> +
> +&uart0 {
> + status = "okay";
> +};
> +
> +&uart1 {
> + status = "okay";
> +};
> +
> +&uart2 {
> + status = "okay";
> +};
> +
> +&uart3 {
> + status = "okay";
> +};
> +
> +&uart4 {
> + status = "okay";
> +};
> +
> +&usbphy {
> + status = "okay";
> +};
> +
> +&usb_host0_ehci {
> + status = "okay";
> +};
> +
> +&usb_host1 {
> + status = "okay";
> +};
> +
> +&usb_otg {
> + status= "okay";
> +};
> +
> +&vopb {
> + status = "okay";
> +};
> +
> +&vopb_mmu {
> + status = "okay";
> +};
> +
> +&vopl {
> + status = "okay";
> + /* Don't use vopl for HDMI */
> + vopl_out: port {
> + /delete-node/ endpoint@0;
> + };
> +};
> +
> +&vopl_mmu {
> + status = "okay";
> +};
> +
> +&wdt {
> + status = "okay";
> +};
> +
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
^ permalink raw reply [flat|nested] 26+ messages in thread* Re: [PATCH V2 2/2] ARM: dts: rockchip: add dts for RK3288-Tinker board
@ 2017-02-09 1:45 ` Andy Yan
0 siblings, 0 replies; 26+ messages in thread
From: Andy Yan @ 2017-02-09 1:45 UTC (permalink / raw)
To: Eddie Cai, robh+dt, mark.rutland, heiko
Cc: devicetree, linux-kernel, linux, linux-rockchip, eddie.cai,
linux-arm-kernel
Hi Eddie:
On 2017年02月06日 10:14, Eddie Cai wrote:
> This patch add basic support for RK3288-Tinker board. We can boot in to rootfs
> with this patch.
>
> Signed-off-by: Eddie Cai <eddie.cai@rock-chips.com>
> ---
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/rk3288-tinker.dts | 543 ++++++++++++++++++++++++++++++++++++
> 2 files changed, 544 insertions(+)
> create mode 100644 arch/arm/boot/dts/rk3288-tinker.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 7327250..4fc05b7 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -679,6 +679,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += \
> rk3288-popmetal.dtb \
> rk3288-r89.dtb \
> rk3288-rock2-square.dtb \
> + rk3288-tinker.dtb \
> rk3288-veyron-brain.dtb \
> rk3288-veyron-jaq.dtb \
> rk3288-veyron-jerry.dtb \
> diff --git a/arch/arm/boot/dts/rk3288-tinker.dts b/arch/arm/boot/dts/rk3288-tinker.dts
> new file mode 100644
> index 0000000..c48563e
> --- /dev/null
> +++ b/arch/arm/boot/dts/rk3288-tinker.dts
> @@ -0,0 +1,543 @@
> +/*
> + * Copyright (c) 2017 Fuzhou Rockchip Electronics Co., Ltd.
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This file is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of the
> + * License, or (at your option) any later version.
> + *
> + * This file is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use,
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +/dts-v1/;
> +
> +#include "rk3288.dtsi"
> +
> +/ {
> + model = "Rockchip RK3288 Tinker Board";
> + compatible = "asus,rk3288-tinker", "rockchip,rk3288";
> +
> + memory {
> + reg = <0x0 0x80000000>;
> + device_type = "memory";
> + };
> +
> + ext_gmac: external-gmac-clock {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <125000000>;
> + clock-output-names = "ext_gmac";
> + };
> +
> + gpio-keys {
> + compatible = "gpio-keys";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + autorepeat;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&pwrbtn>;
> +
> + button@0 {
> + gpios = <&gpio0 5 GPIO_ACTIVE_LOW>;
It's better to describe gpios like: gpios = <&gpio0 RK_PA5
GPIO_ACTIVE_LOW>
see: [0]
[0] https://patchwork.kernel.org/patch/9390693/
> + linux,code = <116>;
> + label = "GPIO Key Power";
> + linux,input-type = <1>;
> + gpio-key,wakeup = <1>;
> + debounce-interval = <100>;
> + };
> + };
> +
> + gpio-leds {
> + compatible = "gpio-leds";
> +
> + pwr-led {
> + gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "default-on";
> + };
> +
> + act-led {
> + gpios=<&gpio2 3 GPIO_ACTIVE_LOW>;
> + linux,default-trigger="mmc0";
> + };
> + };
> +
> + sound {
> + compatible = "simple-audio-card";
> + simple-audio-card,format = "i2s";
> + simple-audio-card,name = "rockchip,tinker-codec";
> + simple-audio-card,mclk-fs = <512>;
> + simple-audio-card,cpu {
> + sound-dai = <&i2s>;
> + };
> + simple-audio-card,codec {
> + sound-dai = <&hdmi>;
> + };
> + };
> +
> + vcc_sys: vsys-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc_sys";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + vcc_sd: sdmmc-regulator {
> + compatible = "regulator-fixed";
> + gpio = <&gpio7 11 GPIO_ACTIVE_LOW>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&sdmmc_pwr>;
> + regulator-name = "vcc_sd";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + startup-delay-us = <100000>;
> + vin-supply = <&vcc_io>;
> + };
> +};
> +
> +&cpu0 {
> + cpu0-supply = <&vdd_cpu>;
> +};
> +
> +&gmac {
> + phy-supply = <&vcc33_lan>;
> + phy-mode = "rgmii";
> + clock_in_out = "input";
> + snps,reset-gpio = <&gpio4 7 0>;
> + snps,reset-active-low;
> + snps,reset-delays-us = <0 10000 1000000>;
> + assigned-clocks = <&cru SCLK_MAC>;
> + assigned-clock-parents = <&ext_gmac>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&rgmii_pins>;
> + tx_delay = <0x30>;
> + rx_delay = <0x10>;
> + status = "ok";
> +};
> +
> +&hdmi {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + #sound-dai-cells = <0>;
> + ddc-i2c-bus = <&i2c5>;
> + status = "okay";
> + /* Don't use vopl for HDMI */
> + ports {
> + hdmi_in: port {
> + /delete-node/ endpoint@1;
> + };
> + };
> +};
> +
> +&i2c0 {
> + status = "okay";
> + clock-frequency = <400000>;
> +
> + rk808: pmic@1b {
> + compatible = "rockchip,rk808";
> + reg = <0x1b>;
> + interrupt-parent = <&gpio0>;
> + interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pmic_int &global_pwroff &dvs_1 &dvs_2>;
> + dvs-gpios = <&gpio0 11 GPIO_ACTIVE_HIGH>,
> + <&gpio0 12 GPIO_ACTIVE_HIGH>;
> +
> + rockchip,system-power-controller;
> + wakeup-source;
> + #clock-cells = <1>;
> + clock-output-names = "xin32k", "rk808-clkout2";
> +
> + vcc1-supply = <&vcc_sys>;
> + vcc2-supply = <&vcc_sys>;
> + vcc3-supply = <&vcc_sys>;
> + vcc4-supply = <&vcc_sys>;
> + vcc6-supply = <&vcc_sys>;
> + vcc7-supply = <&vcc_sys>;
> + vcc8-supply = <&vcc_io>;
> + vcc9-supply = <&vcc_io>;
> + vcc10-supply = <&vcc_io>;
> + vcc11-supply = <&vcc_sys>;
> + vcc12-supply = <&vcc_io>;
> + vddio-supply = <&vcc_io>;
> +
> + regulators {
> + vdd_cpu: DCDC_REG1 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <750000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-name = "vdd_arm";
> + regulator-ramp-delay = <6000>;
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdd_gpu: DCDC_REG2 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <850000>;
> + regulator-max-microvolt = <1250000>;
> + regulator-name = "vdd_gpu";
> + regulator-ramp-delay = <6000>;
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1000000>;
> + };
> + };
> +
> + vcc_ddr: DCDC_REG3 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-name = "vcc_ddr";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> + };
> +
> + vcc_io: DCDC_REG4 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc_io";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <3300000>;
> + };
> + };
> +
> + vcc18_ldo1: LDO_REG1 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc18_ldo1";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1800000>;
> + };
> + };
> +
> + vcc33_mipi: LDO_REG2 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc33_mipi";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdd_10: LDO_REG3 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1000000>;
> + regulator-name = "vdd_10";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1000000>;
> + };
> + };
> +
> + vcc18_codec: LDO_REG4 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc18_codec";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1800000>;
> + };
> + };
> +
> + vccio_sd: LDO_REG5 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vccio_sd";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <3300000>;
> + };
> + };
> +
> + vdd10_lcd: LDO_REG6 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1000000>;
> + regulator-name = "vdd10_lcd";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1000000>;
> + };
> + };
> +
> + vcc_18: LDO_REG7 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc_18";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1800000>;
> + };
> + };
> +
> + vcc18_lcd: LDO_REG8 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc18_lcd";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1800000>;
> + };
> + };
> +
> + vcc33_sd: SWITCH_REG1 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-name = "vcc33_sd";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> + };
> +
> + vcc33_lan: SWITCH_REG2 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-name = "vcc33_lan";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> + };
> + };
> + };
> +};
> +
> +&i2c2 {
> + status = "okay";
> +};
> +
> +&i2c5 {
> + status = "okay";
> +};
> +
> +&i2s {
> + #sound-dai-cells = <0>;
> + status = "okay";
> +};
> +
> +&io_domains {
> + status = "okay";
> +
> + sdcard-supply = <&vccio_sd>;
> +};
> +
> +&pinctrl {
> + pcfg_pull_none_drv_8ma: pcfg-pull-none-drv-8ma {
> + drive-strength = <8>;
> + };
> +
> + pcfg_pull_up_drv_8ma: pcfg-pull-up-drv-8ma {
> + bias-pull-up;
> + drive-strength = <8>;
> + };
> +
> + backlight {
> + bl_en: bl-en {
> + rockchip,pins = <7 2 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + buttons {
> + pwrbtn: pwrbtn {
> + rockchip,pins = <0 5 RK_FUNC_GPIO &pcfg_pull_up>;
> + };
> + };
> +
> + eth_phy {
> + eth_phy_pwr: eth-phy-pwr {
> + rockchip,pins = <0 6 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + pmic {
> + pmic_int: pmic-int {
> + rockchip,pins = <RK_GPIO0 4 RK_FUNC_GPIO \
> + &pcfg_pull_up>;
> + };
> +
> + dvs_1: dvs-1 {
> + rockchip,pins = <RK_GPIO0 11 RK_FUNC_GPIO \
> + &pcfg_pull_down>;
> + };
> +
> + dvs_2: dvs-2 {
> + rockchip,pins = <RK_GPIO0 12 RK_FUNC_GPIO \
> + &pcfg_pull_down>;
> + };
> + };
> +
> + sdmmc {
> + sdmmc_bus4: sdmmc-bus4 {
> + rockchip,pins = <6 16 RK_FUNC_1 &pcfg_pull_up_drv_8ma>,
> + <6 17 RK_FUNC_1 &pcfg_pull_up_drv_8ma>,
> + <6 18 RK_FUNC_1 &pcfg_pull_up_drv_8ma>,
> + <6 19 RK_FUNC_1 &pcfg_pull_up_drv_8ma>;
> + };
> +
> + sdmmc_clk: sdmmc-clk {
> + rockchip,pins = <6 20 RK_FUNC_1 \
> + &pcfg_pull_none_drv_8ma>;
> + };
> +
> + sdmmc_cmd: sdmmc-cmd {
> + rockchip,pins = <6 21 RK_FUNC_1 &pcfg_pull_up_drv_8ma>;
> + };
> +
> + sdmmc_pwr: sdmmc-pwr {
> + rockchip,pins = <7 11 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + usb {
> + host_vbus_drv: host-vbus-drv {
> + rockchip,pins = <0 14 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> +
> + pwr_3g: pwr-3g {
> + rockchip,pins = <7 8 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +};
> +
> +&pwm0 {
> + status = "okay";
> +};
> +
> +&saradc {
> + vref-supply = <&vcc18_ldo1>;
> + status ="okay";
> +};
> +
> +&sdmmc {
> + bus-width = <4>;
> + cap-mmc-highspeed;
> + cap-sd-highspeed;
> + card-detect-delay = <200>;
> + disable-wp; /* wp not hooked up */
> + num-slots = <1>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_bus4>;
> + status = "okay";
> + vmmc-supply = <&vcc33_sd>;
> + vqmmc-supply = <&vccio_sd>;
> +};
> +
> +&tsadc {
> + rockchip,hw-tshut-mode = <1>; /* tshut mode 0:CRU 1:GPIO */
> + rockchip,hw-tshut-polarity = <1>; /* tshut polarity 0:LOW 1:HIGH */
> + status = "okay";
> +};
> +
> +&uart0 {
> + status = "okay";
> +};
> +
> +&uart1 {
> + status = "okay";
> +};
> +
> +&uart2 {
> + status = "okay";
> +};
> +
> +&uart3 {
> + status = "okay";
> +};
> +
> +&uart4 {
> + status = "okay";
> +};
> +
> +&usbphy {
> + status = "okay";
> +};
> +
> +&usb_host0_ehci {
> + status = "okay";
> +};
> +
> +&usb_host1 {
> + status = "okay";
> +};
> +
> +&usb_otg {
> + status= "okay";
> +};
> +
> +&vopb {
> + status = "okay";
> +};
> +
> +&vopb_mmu {
> + status = "okay";
> +};
> +
> +&vopl {
> + status = "okay";
> + /* Don't use vopl for HDMI */
> + vopl_out: port {
> + /delete-node/ endpoint@0;
> + };
> +};
> +
> +&vopl_mmu {
> + status = "okay";
> +};
> +
> +&wdt {
> + status = "okay";
> +};
> +
^ permalink raw reply [flat|nested] 26+ messages in thread* [PATCH V2 2/2] ARM: dts: rockchip: add dts for RK3288-Tinker board
@ 2017-02-09 1:45 ` Andy Yan
0 siblings, 0 replies; 26+ messages in thread
From: Andy Yan @ 2017-02-09 1:45 UTC (permalink / raw)
To: linux-arm-kernel
Hi Eddie:
On 2017?02?06? 10:14, Eddie Cai wrote:
> This patch add basic support for RK3288-Tinker board. We can boot in to rootfs
> with this patch.
>
> Signed-off-by: Eddie Cai <eddie.cai@rock-chips.com>
> ---
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/rk3288-tinker.dts | 543 ++++++++++++++++++++++++++++++++++++
> 2 files changed, 544 insertions(+)
> create mode 100644 arch/arm/boot/dts/rk3288-tinker.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 7327250..4fc05b7 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -679,6 +679,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += \
> rk3288-popmetal.dtb \
> rk3288-r89.dtb \
> rk3288-rock2-square.dtb \
> + rk3288-tinker.dtb \
> rk3288-veyron-brain.dtb \
> rk3288-veyron-jaq.dtb \
> rk3288-veyron-jerry.dtb \
> diff --git a/arch/arm/boot/dts/rk3288-tinker.dts b/arch/arm/boot/dts/rk3288-tinker.dts
> new file mode 100644
> index 0000000..c48563e
> --- /dev/null
> +++ b/arch/arm/boot/dts/rk3288-tinker.dts
> @@ -0,0 +1,543 @@
> +/*
> + * Copyright (c) 2017 Fuzhou Rockchip Electronics Co., Ltd.
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This file is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of the
> + * License, or (at your option) any later version.
> + *
> + * This file is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use,
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +/dts-v1/;
> +
> +#include "rk3288.dtsi"
> +
> +/ {
> + model = "Rockchip RK3288 Tinker Board";
> + compatible = "asus,rk3288-tinker", "rockchip,rk3288";
> +
> + memory {
> + reg = <0x0 0x80000000>;
> + device_type = "memory";
> + };
> +
> + ext_gmac: external-gmac-clock {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <125000000>;
> + clock-output-names = "ext_gmac";
> + };
> +
> + gpio-keys {
> + compatible = "gpio-keys";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + autorepeat;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&pwrbtn>;
> +
> + button at 0 {
> + gpios = <&gpio0 5 GPIO_ACTIVE_LOW>;
It's better to describe gpios like: gpios = <&gpio0 RK_PA5
GPIO_ACTIVE_LOW>
see: [0]
[0] https://patchwork.kernel.org/patch/9390693/
> + linux,code = <116>;
> + label = "GPIO Key Power";
> + linux,input-type = <1>;
> + gpio-key,wakeup = <1>;
> + debounce-interval = <100>;
> + };
> + };
> +
> + gpio-leds {
> + compatible = "gpio-leds";
> +
> + pwr-led {
> + gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "default-on";
> + };
> +
> + act-led {
> + gpios=<&gpio2 3 GPIO_ACTIVE_LOW>;
> + linux,default-trigger="mmc0";
> + };
> + };
> +
> + sound {
> + compatible = "simple-audio-card";
> + simple-audio-card,format = "i2s";
> + simple-audio-card,name = "rockchip,tinker-codec";
> + simple-audio-card,mclk-fs = <512>;
> + simple-audio-card,cpu {
> + sound-dai = <&i2s>;
> + };
> + simple-audio-card,codec {
> + sound-dai = <&hdmi>;
> + };
> + };
> +
> + vcc_sys: vsys-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc_sys";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + vcc_sd: sdmmc-regulator {
> + compatible = "regulator-fixed";
> + gpio = <&gpio7 11 GPIO_ACTIVE_LOW>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&sdmmc_pwr>;
> + regulator-name = "vcc_sd";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + startup-delay-us = <100000>;
> + vin-supply = <&vcc_io>;
> + };
> +};
> +
> +&cpu0 {
> + cpu0-supply = <&vdd_cpu>;
> +};
> +
> +&gmac {
> + phy-supply = <&vcc33_lan>;
> + phy-mode = "rgmii";
> + clock_in_out = "input";
> + snps,reset-gpio = <&gpio4 7 0>;
> + snps,reset-active-low;
> + snps,reset-delays-us = <0 10000 1000000>;
> + assigned-clocks = <&cru SCLK_MAC>;
> + assigned-clock-parents = <&ext_gmac>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&rgmii_pins>;
> + tx_delay = <0x30>;
> + rx_delay = <0x10>;
> + status = "ok";
> +};
> +
> +&hdmi {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + #sound-dai-cells = <0>;
> + ddc-i2c-bus = <&i2c5>;
> + status = "okay";
> + /* Don't use vopl for HDMI */
> + ports {
> + hdmi_in: port {
> + /delete-node/ endpoint at 1;
> + };
> + };
> +};
> +
> +&i2c0 {
> + status = "okay";
> + clock-frequency = <400000>;
> +
> + rk808: pmic at 1b {
> + compatible = "rockchip,rk808";
> + reg = <0x1b>;
> + interrupt-parent = <&gpio0>;
> + interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pmic_int &global_pwroff &dvs_1 &dvs_2>;
> + dvs-gpios = <&gpio0 11 GPIO_ACTIVE_HIGH>,
> + <&gpio0 12 GPIO_ACTIVE_HIGH>;
> +
> + rockchip,system-power-controller;
> + wakeup-source;
> + #clock-cells = <1>;
> + clock-output-names = "xin32k", "rk808-clkout2";
> +
> + vcc1-supply = <&vcc_sys>;
> + vcc2-supply = <&vcc_sys>;
> + vcc3-supply = <&vcc_sys>;
> + vcc4-supply = <&vcc_sys>;
> + vcc6-supply = <&vcc_sys>;
> + vcc7-supply = <&vcc_sys>;
> + vcc8-supply = <&vcc_io>;
> + vcc9-supply = <&vcc_io>;
> + vcc10-supply = <&vcc_io>;
> + vcc11-supply = <&vcc_sys>;
> + vcc12-supply = <&vcc_io>;
> + vddio-supply = <&vcc_io>;
> +
> + regulators {
> + vdd_cpu: DCDC_REG1 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <750000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-name = "vdd_arm";
> + regulator-ramp-delay = <6000>;
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdd_gpu: DCDC_REG2 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <850000>;
> + regulator-max-microvolt = <1250000>;
> + regulator-name = "vdd_gpu";
> + regulator-ramp-delay = <6000>;
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1000000>;
> + };
> + };
> +
> + vcc_ddr: DCDC_REG3 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-name = "vcc_ddr";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> + };
> +
> + vcc_io: DCDC_REG4 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc_io";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <3300000>;
> + };
> + };
> +
> + vcc18_ldo1: LDO_REG1 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc18_ldo1";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1800000>;
> + };
> + };
> +
> + vcc33_mipi: LDO_REG2 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc33_mipi";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdd_10: LDO_REG3 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1000000>;
> + regulator-name = "vdd_10";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1000000>;
> + };
> + };
> +
> + vcc18_codec: LDO_REG4 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc18_codec";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1800000>;
> + };
> + };
> +
> + vccio_sd: LDO_REG5 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vccio_sd";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <3300000>;
> + };
> + };
> +
> + vdd10_lcd: LDO_REG6 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1000000>;
> + regulator-name = "vdd10_lcd";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1000000>;
> + };
> + };
> +
> + vcc_18: LDO_REG7 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc_18";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1800000>;
> + };
> + };
> +
> + vcc18_lcd: LDO_REG8 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc18_lcd";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1800000>;
> + };
> + };
> +
> + vcc33_sd: SWITCH_REG1 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-name = "vcc33_sd";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> + };
> +
> + vcc33_lan: SWITCH_REG2 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-name = "vcc33_lan";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> + };
> + };
> + };
> +};
> +
> +&i2c2 {
> + status = "okay";
> +};
> +
> +&i2c5 {
> + status = "okay";
> +};
> +
> +&i2s {
> + #sound-dai-cells = <0>;
> + status = "okay";
> +};
> +
> +&io_domains {
> + status = "okay";
> +
> + sdcard-supply = <&vccio_sd>;
> +};
> +
> +&pinctrl {
> + pcfg_pull_none_drv_8ma: pcfg-pull-none-drv-8ma {
> + drive-strength = <8>;
> + };
> +
> + pcfg_pull_up_drv_8ma: pcfg-pull-up-drv-8ma {
> + bias-pull-up;
> + drive-strength = <8>;
> + };
> +
> + backlight {
> + bl_en: bl-en {
> + rockchip,pins = <7 2 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + buttons {
> + pwrbtn: pwrbtn {
> + rockchip,pins = <0 5 RK_FUNC_GPIO &pcfg_pull_up>;
> + };
> + };
> +
> + eth_phy {
> + eth_phy_pwr: eth-phy-pwr {
> + rockchip,pins = <0 6 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + pmic {
> + pmic_int: pmic-int {
> + rockchip,pins = <RK_GPIO0 4 RK_FUNC_GPIO \
> + &pcfg_pull_up>;
> + };
> +
> + dvs_1: dvs-1 {
> + rockchip,pins = <RK_GPIO0 11 RK_FUNC_GPIO \
> + &pcfg_pull_down>;
> + };
> +
> + dvs_2: dvs-2 {
> + rockchip,pins = <RK_GPIO0 12 RK_FUNC_GPIO \
> + &pcfg_pull_down>;
> + };
> + };
> +
> + sdmmc {
> + sdmmc_bus4: sdmmc-bus4 {
> + rockchip,pins = <6 16 RK_FUNC_1 &pcfg_pull_up_drv_8ma>,
> + <6 17 RK_FUNC_1 &pcfg_pull_up_drv_8ma>,
> + <6 18 RK_FUNC_1 &pcfg_pull_up_drv_8ma>,
> + <6 19 RK_FUNC_1 &pcfg_pull_up_drv_8ma>;
> + };
> +
> + sdmmc_clk: sdmmc-clk {
> + rockchip,pins = <6 20 RK_FUNC_1 \
> + &pcfg_pull_none_drv_8ma>;
> + };
> +
> + sdmmc_cmd: sdmmc-cmd {
> + rockchip,pins = <6 21 RK_FUNC_1 &pcfg_pull_up_drv_8ma>;
> + };
> +
> + sdmmc_pwr: sdmmc-pwr {
> + rockchip,pins = <7 11 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + usb {
> + host_vbus_drv: host-vbus-drv {
> + rockchip,pins = <0 14 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> +
> + pwr_3g: pwr-3g {
> + rockchip,pins = <7 8 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +};
> +
> +&pwm0 {
> + status = "okay";
> +};
> +
> +&saradc {
> + vref-supply = <&vcc18_ldo1>;
> + status ="okay";
> +};
> +
> +&sdmmc {
> + bus-width = <4>;
> + cap-mmc-highspeed;
> + cap-sd-highspeed;
> + card-detect-delay = <200>;
> + disable-wp; /* wp not hooked up */
> + num-slots = <1>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_bus4>;
> + status = "okay";
> + vmmc-supply = <&vcc33_sd>;
> + vqmmc-supply = <&vccio_sd>;
> +};
> +
> +&tsadc {
> + rockchip,hw-tshut-mode = <1>; /* tshut mode 0:CRU 1:GPIO */
> + rockchip,hw-tshut-polarity = <1>; /* tshut polarity 0:LOW 1:HIGH */
> + status = "okay";
> +};
> +
> +&uart0 {
> + status = "okay";
> +};
> +
> +&uart1 {
> + status = "okay";
> +};
> +
> +&uart2 {
> + status = "okay";
> +};
> +
> +&uart3 {
> + status = "okay";
> +};
> +
> +&uart4 {
> + status = "okay";
> +};
> +
> +&usbphy {
> + status = "okay";
> +};
> +
> +&usb_host0_ehci {
> + status = "okay";
> +};
> +
> +&usb_host1 {
> + status = "okay";
> +};
> +
> +&usb_otg {
> + status= "okay";
> +};
> +
> +&vopb {
> + status = "okay";
> +};
> +
> +&vopb_mmu {
> + status = "okay";
> +};
> +
> +&vopl {
> + status = "okay";
> + /* Don't use vopl for HDMI */
> + vopl_out: port {
> + /delete-node/ endpoint at 0;
> + };
> +};
> +
> +&vopl_mmu {
> + status = "okay";
> +};
> +
> +&wdt {
> + status = "okay";
> +};
> +
^ permalink raw reply [flat|nested] 26+ messages in thread