* [ALSA - driver 0000644]: CMI8738 - Line-in as bass conflicts with line-as rear.
@ 2004-11-11 23:09 bugtrack
0 siblings, 0 replies; 9+ messages in thread
From: bugtrack @ 2004-11-11 23:09 UTC (permalink / raw)
To: alsa-devel
The following issue has been SUBMITTED.
======================================================================
<https://bugtrack.alsa-project.org/alsa-bug/view.php?id=644>
======================================================================
Reported By: jborges
Assigned To: tiwai
======================================================================
Project: ALSA - driver
Issue ID: 644
Category: PCI - cmipci
Reproducibility: always
Severity: minor
Priority: normal
Status: assigned
Distribution: Kurumin 3.2 (a Brazilian flavor of Knoppix) with kde
3.2.3
Kernel Version: Kernel 2.4.25-klg
======================================================================
Date Submitted: 11-12-2004 00:09 CET
Last Modified: 11-12-2004 00:09 CET
======================================================================
Summary: CMI8738 - Line-in as bass conflicts with line-as
rear.
Description:
I'm using Kurumin 3.2 (a Brazilian flavor of Knoppix) in a ASUS P4B533 with
CMI8738 sound chip, processor is Pentium IV 3.0 GHz, 512 RAM and 120
Maxtor Ultra Dma Hard Disk.
Also I use Kde 3.2.3 on Kernel 2.4.25-klg.
This Linux installation works in a dual-boot with windows xp.
The sound works fine (all 6 channels respond very well)under windows xp or
98.
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
Trying to configure my sound to work I noticed some problems with
alsamixer:
1 - As I can see, there is a conflict for the output. I can't see Line-In
been used to output as bass and the same Line-In used to output as rear
(L/R).
2 - I think Line-In would be used to output as Rear (L/R) and Mic to
output as Bass/Center.
What is happening is that: when one uses a 6 channel system there is no
sound in the conflicted Line-In as bass and Mic as center. The little
sound that goes there is squeezed from Line-In as rear. The sound in bass
and center is full of noise. Impossible to listen.
I took some snapshots (2) to show you what I'm talking about. Please take
a look on them in the attached files.
Julio Borges
Rio de Janeiro - Brazil
======================================================================
Issue History
Date Modified Username Field Change
======================================================================
11-12-04 00:09 jborges New Issue
11-12-04 00:09 jborges File Added: sound-cm8738-alsamixergui.png
11-12-04 00:09 jborges Distribution => Kurumin 3.2 (a
Brazilian flavor of Knoppix) with kde 3.2.3
11-12-04 00:09 jborges Kernel Version => Kernel 2.4.25-klg
======================================================================
-------------------------------------------------------
This SF.Net email is sponsored by:
Sybase ASE Linux Express Edition - download now for FREE
LinuxWorld Reader's Choice Award Winner for best database on Linux.
http://ads.osdn.com/?ad_id=5588&alloc_id=12065&op=click
^ permalink raw reply [flat|nested] 9+ messages in thread
* [ALSA - driver 0000644]: CMI8738 - Line-in as bass conflicts with line-as rear.
@ 2004-11-18 17:16 bugtrack
0 siblings, 0 replies; 9+ messages in thread
From: bugtrack @ 2004-11-18 17:16 UTC (permalink / raw)
To: alsa-devel
A NOTE has been added to this issue.
======================================================================
<https://bugtrack.alsa-project.org/alsa-bug/view.php?id=644>
======================================================================
Reported By: jborges
Assigned To: tiwai
======================================================================
Project: ALSA - driver
Issue ID: 644
Category: PCI - cmipci
Reproducibility: always
Severity: minor
Priority: normal
Status: assigned
Distribution: Kurumin 3.2 (a Brazilian flavor of Knoppix) with kde
3.2.3
Kernel Version: Kernel 2.4.25-klg
======================================================================
Date Submitted: 11-12-2004 00:09 CET
Last Modified: 11-18-2004 18:16 CET
======================================================================
Summary: CMI8738 - Line-in as bass conflicts with line-as
rear.
Description:
I'm using Kurumin 3.2 (a Brazilian flavor of Knoppix) in a ASUS P4B533 with
CMI8738 sound chip, processor is Pentium IV 3.0 GHz, 512 RAM and 120
Maxtor Ultra Dma Hard Disk.
Also I use Kde 3.2.3 on Kernel 2.4.25-klg.
This Linux installation works in a dual-boot with windows xp.
The sound works fine (all 6 channels respond very well)under windows xp or
98.
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
Trying to configure my sound to work I noticed some problems with
alsamixer:
1 - As I can see, there is a conflict for the output. I can't see Line-In
been used to output as bass and the same Line-In used to output as rear
(L/R).
2 - I think Line-In would be used to output as Rear (L/R) and Mic to
output as Bass/Center.
What is happening is that: when one uses a 6 channel system there is no
sound in the conflicted Line-In as bass and Mic as center. The little
sound that goes there is squeezed from Line-In as rear. The sound in bass
and center is full of noise. Impossible to listen.
I took some snapshots (2) to show you what I'm talking about. Please take
a look on them in the attached files.
Julio Borges
Rio de Janeiro - Brazil
======================================================================
----------------------------------------------------------------------
tiwai - 11-18-04 18:16
----------------------------------------------------------------------
When 'Line-In as Bass' is turned off and 'Line-In As Rear' on, does 5.1
output work fine? Or still problems?
Issue History
Date Modified Username Field Change
======================================================================
11-12-04 00:09 jborges New Issue
11-12-04 00:09 jborges File Added: sound-cm8738-alsamixergui.png
11-12-04 00:09 jborges Distribution => Kurumin 3.2 (a
Brazilian flavor of Knoppix) with kde 3.2.3
11-12-04 00:09 jborges Kernel Version => Kernel 2.4.25-klg
11-18-04 18:16 tiwai Note Added: 0002455
======================================================================
-------------------------------------------------------
This SF.Net email is sponsored by: InterSystems CACHE
FREE OODBMS DOWNLOAD - A multidimensional database that combines
robust object and relational technologies, making it a perfect match
for Java, C++,COM, XML, ODBC and JDBC. www.intersystems.com/match8
^ permalink raw reply [flat|nested] 9+ messages in thread
* [ALSA - driver 0000644]: CMI8738 - Line-in as bass conflicts with line-as rear.
@ 2004-11-18 18:04 bugtrack
0 siblings, 0 replies; 9+ messages in thread
From: bugtrack @ 2004-11-18 18:04 UTC (permalink / raw)
To: alsa-devel
A NOTE has been added to this issue.
======================================================================
<https://bugtrack.alsa-project.org/alsa-bug/view.php?id=644>
======================================================================
Reported By: jborges
Assigned To: tiwai
======================================================================
Project: ALSA - driver
Issue ID: 644
Category: PCI - cmipci
Reproducibility: always
Severity: minor
Priority: normal
Status: assigned
Distribution: Kurumin 3.2 (a Brazilian flavor of Knoppix) with kde
3.2.3
Kernel Version: Kernel 2.4.25-klg
======================================================================
Date Submitted: 11-12-2004 00:09 CET
Last Modified: 11-18-2004 19:04 CET
======================================================================
Summary: CMI8738 - Line-in as bass conflicts with line-as
rear.
Description:
I'm using Kurumin 3.2 (a Brazilian flavor of Knoppix) in a ASUS P4B533 with
CMI8738 sound chip, processor is Pentium IV 3.0 GHz, 512 RAM and 120
Maxtor Ultra Dma Hard Disk.
Also I use Kde 3.2.3 on Kernel 2.4.25-klg.
This Linux installation works in a dual-boot with windows xp.
The sound works fine (all 6 channels respond very well)under windows xp or
98.
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
Trying to configure my sound to work I noticed some problems with
alsamixer:
1 - As I can see, there is a conflict for the output. I can't see Line-In
been used to output as bass and the same Line-In used to output as rear
(L/R).
2 - I think Line-In would be used to output as Rear (L/R) and Mic to
output as Bass/Center.
What is happening is that: when one uses a 6 channel system there is no
sound in the conflicted Line-In as bass and Mic as center. The little
sound that goes there is squeezed from Line-In as rear. The sound in bass
and center is full of noise. Impossible to listen.
I took some snapshots (2) to show you what I'm talking about. Please take
a look on them in the attached files.
Julio Borges
Rio de Janeiro - Brazil
======================================================================
----------------------------------------------------------------------
tiwai - 11-18-04 18:16
----------------------------------------------------------------------
When 'Line-In as Bass' is turned off and 'Line-In As Rear' on, does 5.1
output work fine? Or still problems?
----------------------------------------------------------------------
jborges - 11-18-04 19:04
----------------------------------------------------------------------
Please take a look at attached file. Notice that both Line-as Rear and
Line-In as Bass are not enabled. I have no means to turn it on or off.
Also notice in the above result of amixer that most of the controls are
set to mono.
Issue History
Date Modified Username Field Change
======================================================================
11-12-04 00:09 jborges New Issue
11-12-04 00:09 jborges File Added: sound-cm8738-alsamixergui.png
11-12-04 00:09 jborges Distribution => Kurumin 3.2 (a
Brazilian flavor of Knoppix) with kde 3.2.3
11-12-04 00:09 jborges Kernel Version => Kernel 2.4.25-klg
11-18-04 18:16 tiwai Note Added: 0002455
11-18-04 19:04 jborges Note Added: 0002458
======================================================================
-------------------------------------------------------
This SF.Net email is sponsored by: InterSystems CACHE
FREE OODBMS DOWNLOAD - A multidimensional database that combines
robust object and relational technologies, making it a perfect match
for Java, C++,COM, XML, ODBC and JDBC. www.intersystems.com/match8
^ permalink raw reply [flat|nested] 9+ messages in thread
* [ALSA - driver 0000644]: CMI8738 - Line-in as bass conflicts with line-as rear.
@ 2004-11-18 18:40 bugtrack
0 siblings, 0 replies; 9+ messages in thread
From: bugtrack @ 2004-11-18 18:40 UTC (permalink / raw)
To: alsa-devel
A NOTE has been added to this issue.
======================================================================
<https://bugtrack.alsa-project.org/alsa-bug/view.php?id=644>
======================================================================
Reported By: jborges
Assigned To: tiwai
======================================================================
Project: ALSA - driver
Issue ID: 644
Category: PCI - cmipci
Reproducibility: always
Severity: minor
Priority: normal
Status: assigned
Distribution: Kurumin 3.2 (a Brazilian flavor of Knoppix) with kde
3.2.3
Kernel Version: Kernel 2.4.25-klg
======================================================================
Date Submitted: 11-12-2004 00:09 CET
Last Modified: 11-18-2004 19:40 CET
======================================================================
Summary: CMI8738 - Line-in as bass conflicts with line-as
rear.
Description:
I'm using Kurumin 3.2 (a Brazilian flavor of Knoppix) in a ASUS P4B533 with
CMI8738 sound chip, processor is Pentium IV 3.0 GHz, 512 RAM and 120
Maxtor Ultra Dma Hard Disk.
Also I use Kde 3.2.3 on Kernel 2.4.25-klg.
This Linux installation works in a dual-boot with windows xp.
The sound works fine (all 6 channels respond very well)under windows xp or
98.
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
Trying to configure my sound to work I noticed some problems with
alsamixer:
1 - As I can see, there is a conflict for the output. I can't see Line-In
been used to output as bass and the same Line-In used to output as rear
(L/R).
2 - I think Line-In would be used to output as Rear (L/R) and Mic to
output as Bass/Center.
What is happening is that: when one uses a 6 channel system there is no
sound in the conflicted Line-In as bass and Mic as center. The little
sound that goes there is squeezed from Line-In as rear. The sound in bass
and center is full of noise. Impossible to listen.
I took some snapshots (2) to show you what I'm talking about. Please take
a look on them in the attached files.
Julio Borges
Rio de Janeiro - Brazil
======================================================================
----------------------------------------------------------------------
jborges - 11-18-04 19:04
----------------------------------------------------------------------
Please take a look at attached file. Notice that both Line-as Rear and
Line-In as Bass are not enabled. I have no means to turn it on or off.
Also notice in the above result of amixer that most of the controls are
set to mono.
----------------------------------------------------------------------
tiwai - 11-18-04 19:40
----------------------------------------------------------------------
I see that both of them are enabled. And amixer output shows that both are
enabled, too.
Forget '[mono]' in the output of amixer. It means only that the mixer
volume/switch has no invididual left/right controls.
Issue History
Date Modified Username Field Change
======================================================================
11-12-04 00:09 jborges New Issue
11-12-04 00:09 jborges File Added: sound-cm8738-alsamixergui.png
11-12-04 00:09 jborges Distribution => Kurumin 3.2 (a
Brazilian flavor of Knoppix) with kde 3.2.3
11-12-04 00:09 jborges Kernel Version => Kernel 2.4.25-klg
11-18-04 18:16 tiwai Note Added: 0002455
11-18-04 19:04 jborges Note Added: 0002458
11-18-04 19:40 tiwai Note Added: 0002463
======================================================================
-------------------------------------------------------
This SF.Net email is sponsored by: InterSystems CACHE
FREE OODBMS DOWNLOAD - A multidimensional database that combines
robust object and relational technologies, making it a perfect match
for Java, C++,COM, XML, ODBC and JDBC. www.intersystems.com/match8
^ permalink raw reply [flat|nested] 9+ messages in thread
* [ALSA - driver 0000644]: CMI8738 - Line-in as bass conflicts with line-as rear.
@ 2004-11-28 9:51 bugtrack
0 siblings, 0 replies; 9+ messages in thread
From: bugtrack @ 2004-11-28 9:51 UTC (permalink / raw)
To: alsa-devel
A NOTE has been added to this issue.
======================================================================
<https://bugtrack.alsa-project.org/alsa-bug/view.php?id=644>
======================================================================
Reported By: jborges
Assigned To: tiwai
======================================================================
Project: ALSA - driver
Issue ID: 644
Category: PCI - cmipci
Reproducibility: always
Severity: minor
Priority: normal
Status: assigned
Distribution: Kurumin 3.2 (a Brazilian flavor of Knoppix) with kde
3.2.3
Kernel Version: Kernel 2.4.25-klg
======================================================================
Date Submitted: 11-12-2004 00:09 CET
Last Modified: 11-28-2004 10:51 CET
======================================================================
Summary: CMI8738 - Line-in as bass conflicts with line-as
rear.
Description:
I'm using Kurumin 3.2 (a Brazilian flavor of Knoppix) in a ASUS P4B533 with
CMI8738 sound chip, processor is Pentium IV 3.0 GHz, 512 RAM and 120
Maxtor Ultra Dma Hard Disk.
Also I use Kde 3.2.3 on Kernel 2.4.25-klg.
This Linux installation works in a dual-boot with windows xp.
The sound works fine (all 6 channels respond very well)under windows xp or
98.
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
Trying to configure my sound to work I noticed some problems with
alsamixer:
1 - As I can see, there is a conflict for the output. I can't see Line-In
been used to output as bass and the same Line-In used to output as rear
(L/R).
2 - I think Line-In would be used to output as Rear (L/R) and Mic to
output as Bass/Center.
What is happening is that: when one uses a 6 channel system there is no
sound in the conflicted Line-In as bass and Mic as center. The little
sound that goes there is squeezed from Line-In as rear. The sound in bass
and center is full of noise. Impossible to listen.
I took some snapshots (2) to show you what I'm talking about. Please take
a look on them in the attached files.
Julio Borges
Rio de Janeiro - Brazil
======================================================================
----------------------------------------------------------------------
tiwai - 11-18-04 19:40
----------------------------------------------------------------------
I see that both of them are enabled. And amixer output shows that both are
enabled, too.
Forget '[mono]' in the output of amixer. It means only that the mixer
volume/switch has no invididual left/right controls.
----------------------------------------------------------------------
jborges - 11-28-04 10:51
----------------------------------------------------------------------
I seems that I made a mistake in my last reply. I wrote something and
attached a new picture. The picture is there but nothing went togheter.
Maybe I forgot to push the add note button. Sorry about that.
What I wanted to tell you is: in the new picture you can see more clearly
that line-in as bass and line-in as rear are not enabled. There is no bars
on them and neither the doted lines above the empty bars. The samething
happen with 3d control and mic as.
Again, sorry.
Issue History
Date Modified Username Field Change
======================================================================
11-12-04 00:09 jborges New Issue
11-12-04 00:09 jborges File Added: sound-cm8738-alsamixergui.png
11-12-04 00:09 jborges Distribution => Kurumin 3.2 (a
Brazilian flavor of Knoppix) with kde 3.2.3
11-12-04 00:09 jborges Kernel Version => Kernel 2.4.25-klg
11-18-04 18:16 tiwai Note Added: 0002455
11-18-04 19:04 jborges Note Added: 0002458
11-18-04 19:40 tiwai Note Added: 0002463
11-20-04 23:25 jborges File Added: sound-cm8738-alsamixer.png
11-28-04 10:51 jborges Note Added: 0002621
======================================================================
-------------------------------------------------------
SF email is sponsored by - The IT Product Guide
Read honest & candid reviews on hundreds of IT Products from real users.
Discover which products truly live up to the hype. Start reading now.
http://productguide.itmanagersjournal.com/
^ permalink raw reply [flat|nested] 9+ messages in thread
* [ALSA - driver 0000644]: CMI8738 - Line-in as bass conflicts with line-as rear.
@ 2004-12-02 18:25 bugtrack
0 siblings, 0 replies; 9+ messages in thread
From: bugtrack @ 2004-12-02 18:25 UTC (permalink / raw)
To: alsa-devel
A NOTE has been added to this issue.
======================================================================
<https://bugtrack.alsa-project.org/alsa-bug/view.php?id=644>
======================================================================
Reported By: jborges
Assigned To: tiwai
======================================================================
Project: ALSA - driver
Issue ID: 644
Category: PCI - cmipci
Reproducibility: always
Severity: minor
Priority: normal
Status: assigned
Distribution: Kurumin 3.2 (a Brazilian flavor of Knoppix) with kde
3.2.3
Kernel Version: Kernel 2.4.25-klg
======================================================================
Date Submitted: 11-12-2004 00:09 CET
Last Modified: 12-02-2004 19:25 CET
======================================================================
Summary: CMI8738 - Line-in as bass conflicts with line-as
rear.
Description:
I'm using Kurumin 3.2 (a Brazilian flavor of Knoppix) in a ASUS P4B533 with
CMI8738 sound chip, processor is Pentium IV 3.0 GHz, 512 RAM and 120
Maxtor Ultra Dma Hard Disk.
Also I use Kde 3.2.3 on Kernel 2.4.25-klg.
This Linux installation works in a dual-boot with windows xp.
The sound works fine (all 6 channels respond very well)under windows xp or
98.
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
Trying to configure my sound to work I noticed some problems with
alsamixer:
1 - As I can see, there is a conflict for the output. I can't see Line-In
been used to output as bass and the same Line-In used to output as rear
(L/R).
2 - I think Line-In would be used to output as Rear (L/R) and Mic to
output as Bass/Center.
What is happening is that: when one uses a 6 channel system there is no
sound in the conflicted Line-In as bass and Mic as center. The little
sound that goes there is squeezed from Line-In as rear. The sound in bass
and center is full of noise. Impossible to listen.
I took some snapshots (2) to show you what I'm talking about. Please take
a look on them in the attached files.
Julio Borges
Rio de Janeiro - Brazil
======================================================================
----------------------------------------------------------------------
jborges - 11-28-04 10:51
----------------------------------------------------------------------
I seems that I made a mistake in my last reply. I wrote something and
attached a new picture. The picture is there but nothing went togheter.
Maybe I forgot to push the add note button. Sorry about that.
What I wanted to tell you is: in the new picture you can see more clearly
that line-in as bass and line-in as rear are not enabled. There is no bars
on them and neither the doted lines above the empty bars. The samething
happen with 3d control and mic as.
Again, sorry.
----------------------------------------------------------------------
tiwai - 12-02-04 19:25
----------------------------------------------------------------------
Both are enabled in the new pictures indeed, too.
You'll see 'MM' on the top of volume bar and '[Off]' in the item name when
the switch is disabled. Try to push 'M' key on the corresponding volume.
Issue History
Date Modified Username Field Change
======================================================================
11-12-04 00:09 jborges New Issue
11-12-04 00:09 jborges File Added: sound-cm8738-alsamixergui.png
11-12-04 00:09 jborges Distribution => Kurumin 3.2 (a
Brazilian flavor of Knoppix) with kde 3.2.3
11-12-04 00:09 jborges Kernel Version => Kernel 2.4.25-klg
11-18-04 18:16 tiwai Note Added: 0002455
11-18-04 19:04 jborges Note Added: 0002458
11-18-04 19:40 tiwai Note Added: 0002463
11-20-04 23:25 jborges File Added: sound-cm8738-alsamixer.png
11-28-04 10:51 jborges Note Added: 0002621
12-02-04 19:25 tiwai Note Added: 0002691
======================================================================
-------------------------------------------------------
SF email is sponsored by - The IT Product Guide
Read honest & candid reviews on hundreds of IT Products from real users.
Discover which products truly live up to the hype. Start reading now.
http://productguide.itmanagersjournal.com/
^ permalink raw reply [flat|nested] 9+ messages in thread
* [ALSA - driver 0000644]: CMI8738 - Line-in as bass conflicts with line-as rear.
@ 2004-12-06 11:32 bugtrack
0 siblings, 0 replies; 9+ messages in thread
From: bugtrack @ 2004-12-06 11:32 UTC (permalink / raw)
To: alsa-devel
A NOTE has been added to this issue.
======================================================================
<https://bugtrack.alsa-project.org/alsa-bug/view.php?id=644>
======================================================================
Reported By: jborges
Assigned To: tiwai
======================================================================
Project: ALSA - driver
Issue ID: 644
Category: PCI - cmipci
Reproducibility: always
Severity: minor
Priority: normal
Status: assigned
Distribution: Kurumin 3.2 (a Brazilian flavor of Knoppix) with kde
3.2.3
Kernel Version: Kernel 2.4.25-klg
======================================================================
Date Submitted: 11-12-2004 00:09 CET
Last Modified: 12-06-2004 12:32 CET
======================================================================
Summary: CMI8738 - Line-in as bass conflicts with line-as
rear.
Description:
I'm using Kurumin 3.2 (a Brazilian flavor of Knoppix) in a ASUS P4B533 with
CMI8738 sound chip, processor is Pentium IV 3.0 GHz, 512 RAM and 120
Maxtor Ultra Dma Hard Disk.
Also I use Kde 3.2.3 on Kernel 2.4.25-klg.
This Linux installation works in a dual-boot with windows xp.
The sound works fine (all 6 channels respond very well)under windows xp or
98.
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
Trying to configure my sound to work I noticed some problems with
alsamixer:
1 - As I can see, there is a conflict for the output. I can't see Line-In
been used to output as bass and the same Line-In used to output as rear
(L/R).
2 - I think Line-In would be used to output as Rear (L/R) and Mic to
output as Bass/Center.
What is happening is that: when one uses a 6 channel system there is no
sound in the conflicted Line-In as bass and Mic as center. The little
sound that goes there is squeezed from Line-In as rear. The sound in bass
and center is full of noise. Impossible to listen.
I took some snapshots (2) to show you what I'm talking about. Please take
a look on them in the attached files.
Julio Borges
Rio de Janeiro - Brazil
======================================================================
----------------------------------------------------------------------
tiwai - 12-02-04 19:25
----------------------------------------------------------------------
Both are enabled in the new pictures indeed, too.
You'll see 'MM' on the top of volume bar and '[Off]' in the item name when
the switch is disabled. Try to push 'M' key on the corresponding volume.
----------------------------------------------------------------------
jborges - 12-06-04 12:32
----------------------------------------------------------------------
It seems that I have a different idea about enable. When I say it is not
enable I want to mean that this is a dead control. I can not push the M
key to mute or umute it. Neither it turns off by pushing that key. Another
thing is there is no way to control the volume in these controls. The
columns above their names stay empty all the time. It not possible to move
the colors inside that columns.
Really sorry for the incovenience. It would be more inteligente just to
forget the whole troble. But, I just like to understand what is going on.
Thanks anyway to stay in this strugle with me.
Issue History
Date Modified Username Field Change
======================================================================
11-12-04 00:09 jborges New Issue
11-12-04 00:09 jborges File Added: sound-cm8738-alsamixergui.png
11-12-04 00:09 jborges Distribution => Kurumin 3.2 (a
Brazilian flavor of Knoppix) with kde 3.2.3
11-12-04 00:09 jborges Kernel Version => Kernel 2.4.25-klg
11-18-04 18:16 tiwai Note Added: 0002455
11-18-04 19:04 jborges Note Added: 0002458
11-18-04 19:40 tiwai Note Added: 0002463
11-20-04 23:25 jborges File Added: sound-cm8738-alsamixer.png
11-28-04 10:51 jborges Note Added: 0002621
12-02-04 19:25 tiwai Note Added: 0002691
12-06-04 12:32 jborges Note Added: 0002727
======================================================================
-------------------------------------------------------
SF email is sponsored by - The IT Product Guide
Read honest & candid reviews on hundreds of IT Products from real users.
Discover which products truly live up to the hype. Start reading now.
http://productguide.itmanagersjournal.com/
^ permalink raw reply [flat|nested] 9+ messages in thread
* [ALSA - driver 0000644]: CMI8738 - Line-in as bass conflicts with line-as rear.
@ 2004-12-07 17:33 bugtrack
0 siblings, 0 replies; 9+ messages in thread
From: bugtrack @ 2004-12-07 17:33 UTC (permalink / raw)
To: alsa-devel
A NOTE has been added to this issue.
======================================================================
<https://bugtrack.alsa-project.org/alsa-bug/view.php?id=644>
======================================================================
Reported By: jborges
Assigned To: tiwai
======================================================================
Project: ALSA - driver
Issue ID: 644
Category: PCI - cmipci
Reproducibility: always
Severity: minor
Priority: normal
Status: assigned
Distribution: Kurumin 3.2 (a Brazilian flavor of Knoppix) with kde
3.2.3
Kernel Version: Kernel 2.4.25-klg
======================================================================
Date Submitted: 11-12-2004 00:09 CET
Last Modified: 12-07-2004 18:33 CET
======================================================================
Summary: CMI8738 - Line-in as bass conflicts with line-as
rear.
Description:
I'm using Kurumin 3.2 (a Brazilian flavor of Knoppix) in a ASUS P4B533 with
CMI8738 sound chip, processor is Pentium IV 3.0 GHz, 512 RAM and 120
Maxtor Ultra Dma Hard Disk.
Also I use Kde 3.2.3 on Kernel 2.4.25-klg.
This Linux installation works in a dual-boot with windows xp.
The sound works fine (all 6 channels respond very well)under windows xp or
98.
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
Trying to configure my sound to work I noticed some problems with
alsamixer:
1 - As I can see, there is a conflict for the output. I can't see Line-In
been used to output as bass and the same Line-In used to output as rear
(L/R).
2 - I think Line-In would be used to output as Rear (L/R) and Mic to
output as Bass/Center.
What is happening is that: when one uses a 6 channel system there is no
sound in the conflicted Line-In as bass and Mic as center. The little
sound that goes there is squeezed from Line-In as rear. The sound in bass
and center is full of noise. Impossible to listen.
I took some snapshots (2) to show you what I'm talking about. Please take
a look on them in the attached files.
Julio Borges
Rio de Janeiro - Brazil
======================================================================
----------------------------------------------------------------------
jborges - 12-06-04 12:32
----------------------------------------------------------------------
It seems that I have a different idea about enable. When I say it is not
enable I want to mean that this is a dead control. I can not push the M
key to mute or umute it. Neither it turns off by pushing that key. Another
thing is there is no way to control the volume in these controls. The
columns above their names stay empty all the time. It not possible to move
the colors inside that columns.
Really sorry for the incovenience. It would be more inteligente just to
forget the whole troble. But, I just like to understand what is going on.
Thanks anyway to stay in this strugle with me.
----------------------------------------------------------------------
tiwai - 12-07-04 18:33
----------------------------------------------------------------------
Hmm, the constant value is OK. They have really no values but only
switches. But non-working switches are of course unexpected problems.
Please attach /proc/asound/card0/cmipci for debugging.
Try to run the following:
amixer set 'Line-In As Bass' off
amixer set 'Line-In As Rear' off
And compare the above proc file. Any changes?
Issue History
Date Modified Username Field Change
======================================================================
11-12-04 00:09 jborges New Issue
11-12-04 00:09 jborges File Added: sound-cm8738-alsamixergui.png
11-12-04 00:09 jborges Distribution => Kurumin 3.2 (a
Brazilian flavor of Knoppix) with kde 3.2.3
11-12-04 00:09 jborges Kernel Version => Kernel 2.4.25-klg
11-18-04 18:16 tiwai Note Added: 0002455
11-18-04 19:04 jborges Note Added: 0002458
11-18-04 19:40 tiwai Note Added: 0002463
11-20-04 23:25 jborges File Added: sound-cm8738-alsamixer.png
11-28-04 10:51 jborges Note Added: 0002621
12-02-04 19:25 tiwai Note Added: 0002691
12-06-04 12:32 jborges Note Added: 0002727
12-07-04 18:33 tiwai Note Added: 0002755
======================================================================
-------------------------------------------------------
SF email is sponsored by - The IT Product Guide
Read honest & candid reviews on hundreds of IT Products from real users.
Discover which products truly live up to the hype. Start reading now.
http://productguide.itmanagersjournal.com/
^ permalink raw reply [flat|nested] 9+ messages in thread
* [ALSA - driver 0000644]: CMI8738 - Line-in as bass conflicts with line-as rear.
@ 2006-07-28 1:45 bugtrack
0 siblings, 0 replies; 9+ messages in thread
From: bugtrack @ 2006-07-28 1:45 UTC (permalink / raw)
To: alsa-devel
The following issue has been CLOSED
======================================================================
<https://bugtrack.alsa-project.org/alsa-bug/view.php?id=644>
======================================================================
Reported By: jborges
Assigned To: tiwai
======================================================================
Project: ALSA - driver
Issue ID: 644
Category: PCI - cmipci
Reproducibility: always
Severity: minor
Priority: normal
Status: closed
Distribution: Kurumin 3.2 (a Brazilian flavor of Knoppix) with kde
3.2.3
Kernel Version: Kernel 2.4.25-klg
Resolution: unable to duplicate
Fixed in Version:
======================================================================
Date Submitted: 11-12-2004 00:09 CET
Last Modified: 07-28-2006 03:45 CEST
======================================================================
Summary: CMI8738 - Line-in as bass conflicts with line-as
rear.
Description:
I'm using Kurumin 3.2 (a Brazilian flavor of Knoppix) in a ASUS P4B533 with
CMI8738 sound chip, processor is Pentium IV 3.0 GHz, 512 RAM and 120
Maxtor Ultra Dma Hard Disk.
Also I use Kde 3.2.3 on Kernel 2.4.25-klg.
This Linux installation works in a dual-boot with windows xp.
The sound works fine (all 6 channels respond very well)under windows xp or
98.
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
Trying to configure my sound to work I noticed some problems with
alsamixer:
1 - As I can see, there is a conflict for the output. I can't see Line-In
been used to output as bass and the same Line-In used to output as rear
(L/R).
2 - I think Line-In would be used to output as Rear (L/R) and Mic to
output as Bass/Center.
What is happening is that: when one uses a 6 channel system there is no
sound in the conflicted Line-In as bass and Mic as center. The little
sound that goes there is squeezed from Line-In as rear. The sound in bass
and center is full of noise. Impossible to listen.
I took some snapshots (2) to show you what I'm talking about. Please take
a look on them in the attached files.
Julio Borges
Rio de Janeiro - Brazil
======================================================================
----------------------------------------------------------------------
jborges - 12-06-04 12:32
----------------------------------------------------------------------
It seems that I have a different idea about enable. When I say it is not
enable I want to mean that this is a dead control. I can not push the M
key to mute or umute it. Neither it turns off by pushing that key. Another
thing is there is no way to control the volume in these controls. The
columns above their names stay empty all the time. It not possible to move
the colors inside that columns.
Really sorry for the incovenience. It would be more inteligente just to
forget the whole troble. But, I just like to understand what is going on.
Thanks anyway to stay in this strugle with me.
----------------------------------------------------------------------
tiwai - 12-07-04 18:33
----------------------------------------------------------------------
Hmm, the constant value is OK. They have really no values but only
switches. But non-working switches are of course unexpected problems.
Please attach /proc/asound/card0/cmipci for debugging.
Try to run the following:
amixer set 'Line-In As Bass' off
amixer set 'Line-In As Rear' off
And compare the above proc file. Any changes?
Issue History
Date Modified Username Field Change
======================================================================
11-12-04 00:09 jborges New Issue
11-12-04 00:09 jborges File Added: sound-cm8738-alsamixergui.png
11-12-04 00:09 jborges Distribution => Kurumin 3.2 (a
Brazilian flavor of Knoppix) with kde 3.2.3
11-12-04 00:09 jborges Kernel Version => Kernel 2.4.25-klg
11-18-04 18:16 tiwai Note Added: 0002455
11-18-04 19:04 jborges Note Added: 0002458
11-18-04 19:40 tiwai Note Added: 0002463
11-20-04 23:25 jborges File Added: sound-cm8738-alsamixer.png
11-28-04 10:51 jborges Note Added: 0002621
12-02-04 19:25 tiwai Note Added: 0002691
12-06-04 12:32 jborges Note Added: 0002727
12-07-04 18:33 tiwai Note Added: 0002755
07-28-06 03:45 Adrian Bunk Status assigned => closed
07-28-06 03:45 Adrian Bunk Resolution open => unable to
duplicate
======================================================================
-------------------------------------------------------------------------
Take Surveys. Earn Cash. Influence the Future of IT
Join SourceForge.net's Techsay panel and you'll get the chance to share your
opinions on IT & business topics through brief surveys -- and earn cash
http://www.techsay.com/default.php?page=join.php&p=sourceforge&CID=DEVDEV
^ permalink raw reply [flat|nested] 9+ messages in thread
end of thread, other threads:[~2006-07-28 1:45 UTC | newest]
Thread overview: 9+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2004-12-02 18:25 [ALSA - driver 0000644]: CMI8738 - Line-in as bass conflicts with line-as rear bugtrack
-- strict thread matches above, loose matches on Subject: below --
2006-07-28 1:45 bugtrack
2004-12-07 17:33 bugtrack
2004-12-06 11:32 bugtrack
2004-11-28 9:51 bugtrack
2004-11-18 18:40 bugtrack
2004-11-18 18:04 bugtrack
2004-11-18 17:16 bugtrack
2004-11-11 23:09 bugtrack
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.