From: "H. Peter Anvin" <hpa@zytor.com>
To: torvalds@linux-foundation.org, andi@firstfloor.org,
linux-kernel@vger.kernel.org
Cc: "H. Peter Anvin" <hpa@zytor.com>
Subject: [x86 setup 33/33] Remove old i386 setup code
Date: Wed, 11 Jul 2007 12:18:58 -0700 [thread overview]
Message-ID: <11841815441652-git-send-email-hpa@zytor.com> (raw)
Message-ID: <5823c605b63bb9712f05fa73ab07d66a4f6e0f92.1184181208.git.hpa@zytor.com> (raw)
In-Reply-To: <11841815442211-git-send-email-hpa@zytor.com>
In-Reply-To: <7aca4ce0a222438c94300a2ea535270a21db8812.1184181208.git.hpa@zytor.com>
From: H. Peter Anvin <hpa@zytor.com>
This removes the old i386 setup code. This is done as a separate patch
to avoid breaking git bisect as some of the i386 code was also used by
the old x86-64 code.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
---
arch/i386/boot/bootsect.S | 98 --
arch/i386/boot/edd.S | 231 -----
arch/i386/boot/setup.S | 1075 ----------------------
arch/i386/boot/video.S | 2043 -----------------------------------------
arch/i386/kernel/verify_cpu.S | 94 --
include/linux/edd.h | 4 -
6 files changed, 0 insertions(+), 3545 deletions(-)
delete mode 100644 arch/i386/boot/bootsect.S
delete mode 100644 arch/i386/boot/edd.S
delete mode 100644 arch/i386/boot/setup.S
delete mode 100644 arch/i386/boot/video.S
delete mode 100644 arch/i386/kernel/verify_cpu.S
diff --git a/arch/i386/boot/bootsect.S b/arch/i386/boot/bootsect.S
deleted file mode 100644
index 011b7a4..0000000
--- a/arch/i386/boot/bootsect.S
+++ /dev/null
@@ -1,98 +0,0 @@
-/*
- * bootsect.S Copyright (C) 1991, 1992 Linus Torvalds
- *
- * modified by Drew Eckhardt
- * modified by Bruce Evans (bde)
- * modified by Chris Noe (May 1999) (as86 -> gas)
- * gutted by H. Peter Anvin (Jan 2003)
- *
- * BIG FAT NOTE: We're in real mode using 64k segments. Therefore segment
- * addresses must be multiplied by 16 to obtain their respective linear
- * addresses. To avoid confusion, linear addresses are written using leading
- * hex while segment addresses are written as segment:offset.
- *
- */
-
-#include <asm/boot.h>
-
-SETUPSECTS = 4 /* default nr of setup-sectors */
-BOOTSEG = 0x07C0 /* original address of boot-sector */
-INITSEG = DEF_INITSEG /* we move boot here - out of the way */
-SETUPSEG = DEF_SETUPSEG /* setup starts here */
-SYSSEG = DEF_SYSSEG /* system loaded at 0x10000 (65536) */
-SYSSIZE = DEF_SYSSIZE /* system size: # of 16-byte clicks */
- /* to be loaded */
-ROOT_DEV = 0 /* ROOT_DEV is now written by "build" */
-SWAP_DEV = 0 /* SWAP_DEV is now written by "build" */
-
-#ifndef SVGA_MODE
-#define SVGA_MODE ASK_VGA
-#endif
-
-#ifndef RAMDISK
-#define RAMDISK 0
-#endif
-
-#ifndef ROOT_RDONLY
-#define ROOT_RDONLY 1
-#endif
-
-.code16
-.text
-
-.global _start
-_start:
-
- # Normalize the start address
- jmpl $BOOTSEG, $start2
-
-start2:
- movw %cs, %ax
- movw %ax, %ds
- movw %ax, %es
- movw %ax, %ss
- movw $0x7c00, %sp
- sti
- cld
-
- movw $bugger_off_msg, %si
-
-msg_loop:
- lodsb
- andb %al, %al
- jz die
- movb $0xe, %ah
- movw $7, %bx
- int $0x10
- jmp msg_loop
-
-die:
- # Allow the user to press a key, then reboot
- xorw %ax, %ax
- int $0x16
- int $0x19
-
- # int 0x19 should never return. In case it does anyway,
- # invoke the BIOS reset code...
- ljmp $0xf000,$0xfff0
-
-
-bugger_off_msg:
- .ascii "Direct booting from floppy is no longer supported.\r\n"
- .ascii "Please use a boot loader program instead.\r\n"
- .ascii "\n"
- .ascii "Remove disk and press any key to reboot . . .\r\n"
- .byte 0
-
-
- # Kernel attributes; used by setup
-
- .org 497
-setup_sects: .byte SETUPSECTS
-root_flags: .word ROOT_RDONLY
-syssize: .word SYSSIZE
-swap_dev: .word SWAP_DEV
-ram_size: .word RAMDISK
-vid_mode: .word SVGA_MODE
-root_dev: .word ROOT_DEV
-boot_flag: .word 0xAA55
diff --git a/arch/i386/boot/edd.S b/arch/i386/boot/edd.S
deleted file mode 100644
index 3432136..0000000
--- a/arch/i386/boot/edd.S
+++ /dev/null
@@ -1,231 +0,0 @@
-/*
- * BIOS Enhanced Disk Drive support
- * Copyright (C) 2002, 2003, 2004 Dell, Inc.
- * by Matt Domsch <Matt_Domsch@dell.com> October 2002
- * conformant to T13 Committee www.t13.org
- * projects 1572D, 1484D, 1386D, 1226DT
- * disk signature read by Matt Domsch <Matt_Domsch@dell.com>
- * and Andrew Wilks <Andrew_Wilks@dell.com> September 2003, June 2004
- * legacy CHS retrieval by Patrick J. LoPresti <patl@users.sourceforge.net>
- * March 2004
- * Command line option parsing, Matt Domsch, November 2004
- */
-
-#include <linux/edd.h>
-#include <asm/setup.h>
-
-#if defined(CONFIG_EDD) || defined(CONFIG_EDD_MODULE)
-
-# It is assumed that %ds == INITSEG here
-
- movb $0, (EDD_MBR_SIG_NR_BUF)
- movb $0, (EDDNR)
-
-# Check the command line for options:
-# edd=of disables EDD completely (edd=off)
-# edd=sk skips the MBR test (edd=skipmbr)
-# edd=on re-enables EDD (edd=on)
-
- pushl %esi
- movw $edd_mbr_sig_start, %di # Default to edd=on
-
- movl %cs:(cmd_line_ptr), %esi
- andl %esi, %esi
- jz old_cl # Old boot protocol?
-
-# Convert to a real-mode pointer in fs:si
- movl %esi, %eax
- shrl $4, %eax
- movw %ax, %fs
- andw $0xf, %si
- jmp have_cl_pointer
-
-# Old-style boot protocol?
-old_cl:
- push %ds # aka INITSEG
- pop %fs
-
- cmpw $0xa33f, (0x20)
- jne done_cl # No command line at all?
- movw (0x22), %si # Pointer relative to INITSEG
-
-# fs:si has the pointer to the command line now
-have_cl_pointer:
-
-# Loop through kernel command line one byte at a time. Just in
-# case the loader is buggy and failed to null-terminate the command line
-# terminate if we get close enough to the end of the segment that we
-# cannot fit "edd=XX"...
-cl_atspace:
- cmpw $-5, %si # Watch for segment wraparound
- jae done_cl
- movl %fs:(%si), %eax
- andb %al, %al # End of line?
- jz done_cl
- cmpl $EDD_CL_EQUALS, %eax
- jz found_edd_equals
- cmpb $0x20, %al # <= space consider whitespace
- ja cl_skipword
- incw %si
- jmp cl_atspace
-
-cl_skipword:
- cmpw $-5, %si # Watch for segment wraparound
- jae done_cl
- movb %fs:(%si), %al # End of string?
- andb %al, %al
- jz done_cl
- cmpb $0x20, %al
- jbe cl_atspace
- incw %si
- jmp cl_skipword
-
-found_edd_equals:
-# only looking at first two characters after equals
-# late overrides early on the command line, so keep going after finding something
- movw %fs:4(%si), %ax
- cmpw $EDD_CL_OFF, %ax # edd=of
- je do_edd_off
- cmpw $EDD_CL_SKIP, %ax # edd=sk
- je do_edd_skipmbr
- cmpw $EDD_CL_ON, %ax # edd=on
- je do_edd_on
- jmp cl_skipword
-do_edd_skipmbr:
- movw $edd_start, %di
- jmp cl_skipword
-do_edd_off:
- movw $edd_done, %di
- jmp cl_skipword
-do_edd_on:
- movw $edd_mbr_sig_start, %di
- jmp cl_skipword
-
-done_cl:
- popl %esi
- jmpw *%di
-
-# Read the first sector of each BIOS disk device and store the 4-byte signature
-edd_mbr_sig_start:
- movb $0x80, %dl # from device 80
- movw $EDD_MBR_SIG_BUF, %bx # store buffer ptr in bx
-edd_mbr_sig_read:
- movl $0xFFFFFFFF, %eax
- movl %eax, (%bx) # assume failure
- pushw %bx
- movb $READ_SECTORS, %ah
- movb $1, %al # read 1 sector
- movb $0, %dh # at head 0
- movw $1, %cx # cylinder 0, sector 0
- pushw %es
- pushw %ds
- popw %es
- movw $EDDBUF, %bx # disk's data goes into EDDBUF
- pushw %dx # work around buggy BIOSes
- stc # work around buggy BIOSes
- int $0x13
- sti # work around buggy BIOSes
- popw %dx
- popw %es
- popw %bx
- jc edd_mbr_sig_done # on failure, we're done.
- cmpb $0, %ah # some BIOSes do not set CF
- jne edd_mbr_sig_done # on failure, we're done.
- movl (EDDBUF+EDD_MBR_SIG_OFFSET), %eax # read sig out of the MBR
- movl %eax, (%bx) # store success
- incb (EDD_MBR_SIG_NR_BUF) # note that we stored something
- incb %dl # increment to next device
- addw $4, %bx # increment sig buffer ptr
- cmpb $EDD_MBR_SIG_MAX, (EDD_MBR_SIG_NR_BUF) # Out of space?
- jb edd_mbr_sig_read # keep looping
-edd_mbr_sig_done:
-
-# Do the BIOS Enhanced Disk Drive calls
-# This consists of two calls:
-# int 13h ah=41h "Check Extensions Present"
-# int 13h ah=48h "Get Device Parameters"
-# int 13h ah=08h "Legacy Get Device Parameters"
-#
-# A buffer of size EDDMAXNR*(EDDEXTSIZE+EDDPARMSIZE) is reserved for our use
-# in the boot_params at EDDBUF. The first four bytes of which are
-# used to store the device number, interface support map and version
-# results from fn41. The next four bytes are used to store the legacy
-# cylinders, heads, and sectors from fn08. The following 74 bytes are used to
-# store the results from fn48. Starting from device 80h, fn41, then fn48
-# are called and their results stored in EDDBUF+n*(EDDEXTSIZE+EDDPARMIZE).
-# Then the pointer is incremented to store the data for the next call.
-# This repeats until either a device doesn't exist, or until EDDMAXNR
-# devices have been stored.
-# The one tricky part is that ds:si always points EDDEXTSIZE bytes into
-# the structure, and the fn41 and fn08 results are stored at offsets
-# from there. This removes the need to increment the pointer for
-# every store, and leaves it ready for the fn48 call.
-# A second one-byte buffer, EDDNR, in the boot_params stores
-# the number of BIOS devices which exist, up to EDDMAXNR.
-# In setup.c, copy_edd() stores both boot_params buffers away
-# for later use, as they would get overwritten otherwise.
-# This code is sensitive to the size of the structs in edd.h
-edd_start:
- # %ds points to the bootsector
- # result buffer for fn48
- movw $EDDBUF+EDDEXTSIZE, %si # in ds:si, fn41 results
- # kept just before that
- movb $0x80, %dl # BIOS device 0x80
-
-edd_check_ext:
- movb $CHECKEXTENSIONSPRESENT, %ah # Function 41
- movw $EDDMAGIC1, %bx # magic
- int $0x13 # make the call
- jc edd_done # no more BIOS devices
-
- cmpw $EDDMAGIC2, %bx # is magic right?
- jne edd_next # nope, next...
-
- movb %dl, %ds:-8(%si) # store device number
- movb %ah, %ds:-7(%si) # store version
- movw %cx, %ds:-6(%si) # store extensions
- incb (EDDNR) # note that we stored something
-
-edd_get_device_params:
- movw $EDDPARMSIZE, %ds:(%si) # put size
- movw $0x0, %ds:2(%si) # work around buggy BIOSes
- movb $GETDEVICEPARAMETERS, %ah # Function 48
- int $0x13 # make the call
- # Don't check for fail return
- # it doesn't matter.
-edd_get_legacy_chs:
- xorw %ax, %ax
- movw %ax, %ds:-4(%si)
- movw %ax, %ds:-2(%si)
- # Ralf Brown's Interrupt List says to set ES:DI to
- # 0000h:0000h "to guard against BIOS bugs"
- pushw %es
- movw %ax, %es
- movw %ax, %di
- pushw %dx # legacy call clobbers %dl
- movb $LEGACYGETDEVICEPARAMETERS, %ah # Function 08
- int $0x13 # make the call
- jc edd_legacy_done # failed
- movb %cl, %al # Low 6 bits are max
- andb $0x3F, %al # sector number
- movb %al, %ds:-1(%si) # Record max sect
- movb %dh, %ds:-2(%si) # Record max head number
- movb %ch, %al # Low 8 bits of max cyl
- shr $6, %cl
- movb %cl, %ah # High 2 bits of max cyl
- movw %ax, %ds:-4(%si)
-
-edd_legacy_done:
- popw %dx
- popw %es
- movw %si, %ax # increment si
- addw $EDDPARMSIZE+EDDEXTSIZE, %ax
- movw %ax, %si
-
-edd_next:
- incb %dl # increment to next device
- cmpb $EDDMAXNR, (EDDNR) # Out of space?
- jb edd_check_ext # keep looping
-
-edd_done:
-#endif
diff --git a/arch/i386/boot/setup.S b/arch/i386/boot/setup.S
deleted file mode 100644
index 6dbcc95..0000000
--- a/arch/i386/boot/setup.S
+++ /dev/null
@@ -1,1075 +0,0 @@
-/*
- * setup.S Copyright (C) 1991, 1992 Linus Torvalds
- *
- * setup.s is responsible for getting the system data from the BIOS,
- * and putting them into the appropriate places in system memory.
- * both setup.s and system has been loaded by the bootblock.
- *
- * This code asks the bios for memory/disk/other parameters, and
- * puts them in a "safe" place: 0x90000-0x901FF, ie where the
- * boot-block used to be. It is then up to the protected mode
- * system to read them from there before the area is overwritten
- * for buffer-blocks.
- *
- * Move PS/2 aux init code to psaux.c
- * (troyer@saifr00.cfsat.Honeywell.COM) 03Oct92
- *
- * some changes and additional features by Christoph Niemann,
- * March 1993/June 1994 (Christoph.Niemann@linux.org)
- *
- * add APM BIOS checking by Stephen Rothwell, May 1994
- * (sfr@canb.auug.org.au)
- *
- * High load stuff, initrd support and position independency
- * by Hans Lermen & Werner Almesberger, February 1996
- * <lermen@elserv.ffm.fgan.de>, <almesber@lrc.epfl.ch>
- *
- * Video handling moved to video.S by Martin Mares, March 1996
- * <mj@k332.feld.cvut.cz>
- *
- * Extended memory detection scheme retwiddled by orc@pell.chi.il.us (david
- * parsons) to avoid loadlin confusion, July 1997
- *
- * Transcribed from Intel (as86) -> AT&T (gas) by Chris Noe, May 1999.
- * <stiker@northlink.com>
- *
- * Fix to work around buggy BIOSes which don't use carry bit correctly
- * and/or report extended memory in CX/DX for e801h memory size detection
- * call. As a result the kernel got wrong figures. The int15/e801h docs
- * from Ralf Brown interrupt list seem to indicate AX/BX should be used
- * anyway. So to avoid breaking many machines (presumably there was a reason
- * to orginally use CX/DX instead of AX/BX), we do a kludge to see
- * if CX/DX have been changed in the e801 call and if so use AX/BX .
- * Michael Miller, April 2001 <michaelm@mjmm.org>
- *
- * New A20 code ported from SYSLINUX by H. Peter Anvin. AMD Elan bugfixes
- * by Robert Schwebel, December 2001 <robert@schwebel.de>
- */
-
-#include <asm/segment.h>
-#include <linux/utsrelease.h>
-#include <linux/compile.h>
-#include <asm/boot.h>
-#include <asm/e820.h>
-#include <asm/page.h>
-#include <asm/setup.h>
-
-/* Signature words to ensure LILO loaded us right */
-#define SIG1 0xAA55
-#define SIG2 0x5A5A
-
-INITSEG = DEF_INITSEG # 0x9000, we move boot here, out of the way
-SYSSEG = DEF_SYSSEG # 0x1000, system loaded at 0x10000 (65536).
-SETUPSEG = DEF_SETUPSEG # 0x9020, this is the current segment
- # ... and the former contents of CS
-
-DELTA_INITSEG = SETUPSEG - INITSEG # 0x0020
-
-.code16
-.globl begtext, begdata, begbss, endtext, enddata, endbss
-
-.text
-begtext:
-.data
-begdata:
-.bss
-begbss:
-.text
-
-start:
- jmp trampoline
-
-# This is the setup header, and it must start at %cs:2 (old 0x9020:2)
-
- .ascii "HdrS" # header signature
- .word 0x0206 # header version number (>= 0x0105)
- # or else old loadlin-1.5 will fail)
-realmode_swtch: .word 0, 0 # default_switch, SETUPSEG
-start_sys_seg: .word SYSSEG
- .word kernel_version # pointing to kernel version string
- # above section of header is compatible
- # with loadlin-1.5 (header v1.5). Don't
- # change it.
-
-type_of_loader: .byte 0 # = 0, old one (LILO, Loadlin,
- # Bootlin, SYSLX, bootsect...)
- # See Documentation/i386/boot.txt for
- # assigned ids
-
-# flags, unused bits must be zero (RFU) bit within loadflags
-loadflags:
-LOADED_HIGH = 1 # If set, the kernel is loaded high
-CAN_USE_HEAP = 0x80 # If set, the loader also has set
- # heap_end_ptr to tell how much
- # space behind setup.S can be used for
- # heap purposes.
- # Only the loader knows what is free
-#ifndef __BIG_KERNEL__
- .byte 0
-#else
- .byte LOADED_HIGH
-#endif
-
-setup_move_size: .word 0x8000 # size to move, when setup is not
- # loaded at 0x90000. We will move setup
- # to 0x90000 then just before jumping
- # into the kernel. However, only the
- # loader knows how much data behind
- # us also needs to be loaded.
-
-code32_start: # here loaders can put a different
- # start address for 32-bit code.
-#ifndef __BIG_KERNEL__
- .long 0x1000 # 0x1000 = default for zImage
-#else
- .long 0x100000 # 0x100000 = default for big kernel
-#endif
-
-ramdisk_image: .long 0 # address of loaded ramdisk image
- # Here the loader puts the 32-bit
- # address where it loaded the image.
- # This only will be read by the kernel.
-
-ramdisk_size: .long 0 # its size in bytes
-
-bootsect_kludge:
- .long 0 # obsolete
-
-heap_end_ptr: .word modelist+1024 # (Header version 0x0201 or later)
- # space from here (exclusive) down to
- # end of setup code can be used by setup
- # for local heap purposes.
-
-pad1: .word 0
-cmd_line_ptr: .long 0 # (Header version 0x0202 or later)
- # If nonzero, a 32-bit pointer
- # to the kernel command line.
- # The command line should be
- # located between the start of
- # setup and the end of low
- # memory (0xa0000), or it may
- # get overwritten before it
- # gets read. If this field is
- # used, there is no longer
- # anything magical about the
- # 0x90000 segment; the setup
- # can be located anywhere in
- # low memory 0x10000 or higher.
-
-ramdisk_max: .long (-__PAGE_OFFSET-(512 << 20)-1) & 0x7fffffff
- # (Header version 0x0203 or later)
- # The highest safe address for
- # the contents of an initrd
-
-kernel_alignment: .long CONFIG_PHYSICAL_ALIGN #physical addr alignment
- #required for protected mode
- #kernel
-#ifdef CONFIG_RELOCATABLE
-relocatable_kernel: .byte 1
-#else
-relocatable_kernel: .byte 0
-#endif
-pad2: .byte 0
-pad3: .word 0
-
-cmdline_size: .long COMMAND_LINE_SIZE-1 #length of the command line,
- #added with boot protocol
- #version 2.06
-
-trampoline: call start_of_setup
- .align 16
- # The offset at this point is 0x240
- .space (0xeff-0x240+1) # E820 & EDD space (ending at 0xeff)
-# End of setup header #####################################################
-
-start_of_setup:
-# Bootlin depends on this being done early
- movw $0x01500, %ax
- movb $0x81, %dl
- int $0x13
-
-#ifdef SAFE_RESET_DISK_CONTROLLER
-# Reset the disk controller.
- movw $0x0000, %ax
- movb $0x80, %dl
- int $0x13
-#endif
-
-# Set %ds = %cs, we know that SETUPSEG = %cs at this point
- movw %cs, %ax # aka SETUPSEG
- movw %ax, %ds
-# Check signature at end of setup
- cmpw $SIG1, setup_sig1
- jne bad_sig
-
- cmpw $SIG2, setup_sig2
- jne bad_sig
-
- jmp good_sig1
-
-# Routine to print asciiz string at ds:si
-prtstr:
- lodsb
- andb %al, %al
- jz fin
-
- call prtchr
- jmp prtstr
-
-fin: ret
-
-# Space printing
-prtsp2: call prtspc # Print double space
-prtspc: movb $0x20, %al # Print single space (note: fall-thru)
-
-# Part of above routine, this one just prints ascii al
-prtchr: pushw %ax
- pushw %cx
- movw $7,%bx
- movw $0x01, %cx
- movb $0x0e, %ah
- int $0x10
- popw %cx
- popw %ax
- ret
-
-beep: movb $0x07, %al
- jmp prtchr
-
-no_sig_mess: .string "No setup signature found ..."
-
-good_sig1:
- jmp good_sig
-
-# We now have to find the rest of the setup code/data
-bad_sig:
- movw %cs, %ax # SETUPSEG
- subw $DELTA_INITSEG, %ax # INITSEG
- movw %ax, %ds
- xorb %bh, %bh
- movb (497), %bl # get setup sect from bootsect
- subw $4, %bx # LILO loads 4 sectors of setup
- shlw $8, %bx # convert to words (1sect=2^8 words)
- movw %bx, %cx
- shrw $3, %bx # convert to segment
- addw $SYSSEG, %bx
- movw %bx, %cs:start_sys_seg
-# Move rest of setup code/data to here
- movw $2048, %di # four sectors loaded by LILO
- subw %si, %si
- pushw %cs
- popw %es
- movw $SYSSEG, %ax
- movw %ax, %ds
- rep
- movsw
- movw %cs, %ax # aka SETUPSEG
- movw %ax, %ds
- cmpw $SIG1, setup_sig1
- jne no_sig
-
- cmpw $SIG2, setup_sig2
- jne no_sig
-
- jmp good_sig
-
-no_sig:
- lea no_sig_mess, %si
- call prtstr
-
-no_sig_loop:
- hlt
- jmp no_sig_loop
-
-good_sig:
- movw %cs, %ax # aka SETUPSEG
- subw $DELTA_INITSEG, %ax # aka INITSEG
- movw %ax, %ds
-# Check if an old loader tries to load a big-kernel
- testb $LOADED_HIGH, %cs:loadflags # Do we have a big kernel?
- jz loader_ok # No, no danger for old loaders.
-
- cmpb $0, %cs:type_of_loader # Do we have a loader that
- # can deal with us?
- jnz loader_ok # Yes, continue.
-
- pushw %cs # No, we have an old loader,
- popw %ds # die.
- lea loader_panic_mess, %si
- call prtstr
-
- jmp no_sig_loop
-
-loader_panic_mess: .string "Wrong loader, giving up..."
-
-# check minimum cpuid
-# we do this here because it is the last place we can actually
-# show a user visible error message. Later the video modus
-# might be already messed up.
-loader_ok:
- call verify_cpu
- testl %eax,%eax
- jz cpu_ok
- movw %cs,%ax # aka SETUPSEG
- movw %ax,%ds
- lea cpu_panic_mess,%si
- call prtstr
-1: jmp 1b
-
-cpu_panic_mess:
- .asciz "PANIC: CPU too old for this kernel."
-
-#include "../kernel/verify_cpu.S"
-
-cpu_ok:
-# Get memory size (extended mem, kB)
-
- xorl %eax, %eax
- movl %eax, (0x1e0)
-#ifndef STANDARD_MEMORY_BIOS_CALL
- movb %al, (E820NR)
-# Try three different memory detection schemes. First, try
-# e820h, which lets us assemble a memory map, then try e801h,
-# which returns a 32-bit memory size, and finally 88h, which
-# returns 0-64m
-
-# method E820H:
-# the memory map from hell. e820h returns memory classified into
-# a whole bunch of different types, and allows memory holes and
-# everything. We scan through this memory map and build a list
-# of the first 32 memory areas, which we return at [E820MAP].
-# This is documented at http://www.acpi.info/, in the ACPI 2.0 specification.
-
-#define SMAP 0x534d4150
-
-meme820:
- xorl %ebx, %ebx # continuation counter
- movw $E820MAP, %di # point into the whitelist
- # so we can have the bios
- # directly write into it.
-
-jmpe820:
- movl $0x0000e820, %eax # e820, upper word zeroed
- movl $SMAP, %edx # ascii 'SMAP'
- movl $20, %ecx # size of the e820rec
- pushw %ds # data record.
- popw %es
- int $0x15 # make the call
- jc bail820 # fall to e801 if it fails
-
- cmpl $SMAP, %eax # check the return is `SMAP'
- jne bail820 # fall to e801 if it fails
-
-# cmpl $1, 16(%di) # is this usable memory?
-# jne again820
-
- # If this is usable memory, we save it by simply advancing %di by
- # sizeof(e820rec).
- #
-good820:
- movb (E820NR), %al # up to 128 entries
- cmpb $E820MAX, %al
- jae bail820
-
- incb (E820NR)
- movw %di, %ax
- addw $20, %ax
- movw %ax, %di
-again820:
- cmpl $0, %ebx # check to see if
- jne jmpe820 # %ebx is set to EOF
-bail820:
-
-
-# method E801H:
-# memory size is in 1k chunksizes, to avoid confusing loadlin.
-# we store the 0xe801 memory size in a completely different place,
-# because it will most likely be longer than 16 bits.
-# (use 1e0 because that's what Larry Augustine uses in his
-# alternative new memory detection scheme, and it's sensible
-# to write everything into the same place.)
-
-meme801:
- stc # fix to work around buggy
- xorw %cx,%cx # BIOSes which don't clear/set
- xorw %dx,%dx # carry on pass/error of
- # e801h memory size call
- # or merely pass cx,dx though
- # without changing them.
- movw $0xe801, %ax
- int $0x15
- jc mem88
-
- cmpw $0x0, %cx # Kludge to handle BIOSes
- jne e801usecxdx # which report their extended
- cmpw $0x0, %dx # memory in AX/BX rather than
- jne e801usecxdx # CX/DX. The spec I have read
- movw %ax, %cx # seems to indicate AX/BX
- movw %bx, %dx # are more reasonable anyway...
-
-e801usecxdx:
- andl $0xffff, %edx # clear sign extend
- shll $6, %edx # and go from 64k to 1k chunks
- movl %edx, (0x1e0) # store extended memory size
- andl $0xffff, %ecx # clear sign extend
- addl %ecx, (0x1e0) # and add lower memory into
- # total size.
-
-# Ye Olde Traditional Methode. Returns the memory size (up to 16mb or
-# 64mb, depending on the bios) in ax.
-mem88:
-
-#endif
- movb $0x88, %ah
- int $0x15
- movw %ax, (2)
-
-# Set the keyboard repeat rate to the max
- movw $0x0305, %ax
- xorw %bx, %bx
- int $0x16
-
-# Check for video adapter and its parameters and allow the
-# user to browse video modes.
- call video # NOTE: we need %ds pointing
- # to bootsector
-
-# Get hd0 data...
- xorw %ax, %ax
- movw %ax, %ds
- ldsw (4 * 0x41), %si
- movw %cs, %ax # aka SETUPSEG
- subw $DELTA_INITSEG, %ax # aka INITSEG
- pushw %ax
- movw %ax, %es
- movw $0x0080, %di
- movw $0x10, %cx
- pushw %cx
- cld
- rep
- movsb
-# Get hd1 data...
- xorw %ax, %ax
- movw %ax, %ds
- ldsw (4 * 0x46), %si
- popw %cx
- popw %es
- movw $0x0090, %di
- rep
- movsb
-# Check that there IS a hd1 :-)
- movw $0x01500, %ax
- movb $0x81, %dl
- int $0x13
- jc no_disk1
-
- cmpb $3, %ah
- je is_disk1
-
-no_disk1:
- movw %cs, %ax # aka SETUPSEG
- subw $DELTA_INITSEG, %ax # aka INITSEG
- movw %ax, %es
- movw $0x0090, %di
- movw $0x10, %cx
- xorw %ax, %ax
- cld
- rep
- stosb
-is_disk1:
-# check for Micro Channel (MCA) bus
- movw %cs, %ax # aka SETUPSEG
- subw $DELTA_INITSEG, %ax # aka INITSEG
- movw %ax, %ds
- xorw %ax, %ax
- movw %ax, (0xa0) # set table length to 0
- movb $0xc0, %ah
- stc
- int $0x15 # moves feature table to es:bx
- jc no_mca
-
- pushw %ds
- movw %es, %ax
- movw %ax, %ds
- movw %cs, %ax # aka SETUPSEG
- subw $DELTA_INITSEG, %ax # aka INITSEG
- movw %ax, %es
- movw %bx, %si
- movw $0xa0, %di
- movw (%si), %cx
- addw $2, %cx # table length is a short
- cmpw $0x10, %cx
- jc sysdesc_ok
-
- movw $0x10, %cx # we keep only first 16 bytes
-sysdesc_ok:
- rep
- movsb
- popw %ds
-no_mca:
-#ifdef CONFIG_X86_VOYAGER
- movb $0xff, 0x40 # flag on config found
- movb $0xc0, %al
- mov $0xff, %ah
- int $0x15 # put voyager config info at es:di
- jc no_voyager
- movw $0x40, %si # place voyager info in apm table
- cld
- movw $7, %cx
-voyager_rep:
- movb %es:(%di), %al
- movb %al,(%si)
- incw %di
- incw %si
- decw %cx
- jnz voyager_rep
-no_voyager:
-#endif
-# Check for PS/2 pointing device
- movw %cs, %ax # aka SETUPSEG
- subw $DELTA_INITSEG, %ax # aka INITSEG
- movw %ax, %ds
- movb $0, (0x1ff) # default is no pointing device
- int $0x11 # int 0x11: equipment list
- testb $0x04, %al # check if mouse installed
- jz no_psmouse
-
- movb $0xAA, (0x1ff) # device present
-no_psmouse:
-
-#if defined(CONFIG_X86_SPEEDSTEP_SMI) || defined(CONFIG_X86_SPEEDSTEP_SMI_MODULE)
- movl $0x0000E980, %eax # IST Support
- movl $0x47534943, %edx # Request value
- int $0x15
-
- movl %eax, (96)
- movl %ebx, (100)
- movl %ecx, (104)
- movl %edx, (108)
-#endif
-
-#if defined(CONFIG_APM) || defined(CONFIG_APM_MODULE)
-# Then check for an APM BIOS...
- # %ds points to the bootsector
- movw $0, 0x40 # version = 0 means no APM BIOS
- movw $0x05300, %ax # APM BIOS installation check
- xorw %bx, %bx
- int $0x15
- jc done_apm_bios # Nope, no APM BIOS
-
- cmpw $0x0504d, %bx # Check for "PM" signature
- jne done_apm_bios # No signature, no APM BIOS
-
- andw $0x02, %cx # Is 32 bit supported?
- je done_apm_bios # No 32-bit, no (good) APM BIOS
-
- movw $0x05304, %ax # Disconnect first just in case
- xorw %bx, %bx
- int $0x15 # ignore return code
- movw $0x05303, %ax # 32 bit connect
- xorl %ebx, %ebx
- xorw %cx, %cx # paranoia :-)
- xorw %dx, %dx # ...
- xorl %esi, %esi # ...
- xorw %di, %di # ...
- int $0x15
- jc no_32_apm_bios # Ack, error.
-
- movw %ax, (66) # BIOS code segment
- movl %ebx, (68) # BIOS entry point offset
- movw %cx, (72) # BIOS 16 bit code segment
- movw %dx, (74) # BIOS data segment
- movl %esi, (78) # BIOS code segment lengths
- movw %di, (82) # BIOS data segment length
-# Redo the installation check as the 32 bit connect
-# modifies the flags returned on some BIOSs
- movw $0x05300, %ax # APM BIOS installation check
- xorw %bx, %bx
- xorw %cx, %cx # paranoia
- int $0x15
- jc apm_disconnect # error -> shouldn't happen
-
- cmpw $0x0504d, %bx # check for "PM" signature
- jne apm_disconnect # no sig -> shouldn't happen
-
- movw %ax, (64) # record the APM BIOS version
- movw %cx, (76) # and flags
- jmp done_apm_bios
-
-apm_disconnect: # Tidy up
- movw $0x05304, %ax # Disconnect
- xorw %bx, %bx
- int $0x15 # ignore return code
-
- jmp done_apm_bios
-
-no_32_apm_bios:
- andw $0xfffd, (76) # remove 32 bit support bit
-done_apm_bios:
-#endif
-
-#include "edd.S"
-
-# Now we want to move to protected mode ...
- cmpw $0, %cs:realmode_swtch
- jz rmodeswtch_normal
-
- lcall *%cs:realmode_swtch
-
- jmp rmodeswtch_end
-
-rmodeswtch_normal:
- pushw %cs
- call default_switch
-
-rmodeswtch_end:
-# Now we move the system to its rightful place ... but we check if we have a
-# big-kernel. In that case we *must* not move it ...
- testb $LOADED_HIGH, %cs:loadflags
- jz do_move0 # .. then we have a normal low
- # loaded zImage
- # .. or else we have a high
- # loaded bzImage
- jmp end_move # ... and we skip moving
-
-do_move0:
- movw $0x100, %ax # start of destination segment
- movw %cs, %bp # aka SETUPSEG
- subw $DELTA_INITSEG, %bp # aka INITSEG
- movw %cs:start_sys_seg, %bx # start of source segment
- cld
-do_move:
- movw %ax, %es # destination segment
- incb %ah # instead of add ax,#0x100
- movw %bx, %ds # source segment
- addw $0x100, %bx
- subw %di, %di
- subw %si, %si
- movw $0x800, %cx
- rep
- movsw
- cmpw %bp, %bx # assume start_sys_seg > 0x200,
- # so we will perhaps read one
- # page more than needed, but
- # never overwrite INITSEG
- # because destination is a
- # minimum one page below source
- jb do_move
-
-end_move:
-# then we load the segment descriptors
- movw %cs, %ax # aka SETUPSEG
- movw %ax, %ds
-
-# Check whether we need to be downward compatible with version <=201
- cmpl $0, cmd_line_ptr
- jne end_move_self # loader uses version >=202 features
- cmpb $0x20, type_of_loader
- je end_move_self # bootsect loader, we know of it
-
-# Boot loader doesnt support boot protocol version 2.02.
-# If we have our code not at 0x90000, we need to move it there now.
-# We also then need to move the params behind it (commandline)
-# Because we would overwrite the code on the current IP, we move
-# it in two steps, jumping high after the first one.
- movw %cs, %ax
- cmpw $SETUPSEG, %ax
- je end_move_self
-
- cli # make sure we really have
- # interrupts disabled !
- # because after this the stack
- # should not be used
- subw $DELTA_INITSEG, %ax # aka INITSEG
- movw %ss, %dx
- cmpw %ax, %dx
- jb move_self_1
-
- addw $INITSEG, %dx
- subw %ax, %dx # this will go into %ss after
- # the move
-move_self_1:
- movw %ax, %ds
- movw $INITSEG, %ax # real INITSEG
- movw %ax, %es
- movw %cs:setup_move_size, %cx
- std # we have to move up, so we use
- # direction down because the
- # areas may overlap
- movw %cx, %di
- decw %di
- movw %di, %si
- subw $move_self_here+0x200, %cx
- rep
- movsb
- ljmp $SETUPSEG, $move_self_here
-
-move_self_here:
- movw $move_self_here+0x200, %cx
- rep
- movsb
- movw $SETUPSEG, %ax
- movw %ax, %ds
- movw %dx, %ss
-end_move_self: # now we are at the right place
-
-#
-# Enable A20. This is at the very best an annoying procedure.
-# A20 code ported from SYSLINUX 1.52-1.63 by H. Peter Anvin.
-# AMD Elan bug fix by Robert Schwebel.
-#
-
-#if defined(CONFIG_X86_ELAN)
- movb $0x02, %al # alternate A20 gate
- outb %al, $0x92 # this works on SC410/SC520
-a20_elan_wait:
- call a20_test
- jz a20_elan_wait
- jmp a20_done
-#endif
-
-
-A20_TEST_LOOPS = 32 # Iterations per wait
-A20_ENABLE_LOOPS = 255 # Total loops to try
-
-
-#ifndef CONFIG_X86_VOYAGER
-a20_try_loop:
-
- # First, see if we are on a system with no A20 gate.
-a20_none:
- call a20_test
- jnz a20_done
-
- # Next, try the BIOS (INT 0x15, AX=0x2401)
-a20_bios:
- movw $0x2401, %ax
- pushfl # Be paranoid about flags
- int $0x15
- popfl
-
- call a20_test
- jnz a20_done
-
- # Try enabling A20 through the keyboard controller
-#endif /* CONFIG_X86_VOYAGER */
-a20_kbc:
- call empty_8042
-
-#ifndef CONFIG_X86_VOYAGER
- call a20_test # Just in case the BIOS worked
- jnz a20_done # but had a delayed reaction.
-#endif
-
- movb $0xD1, %al # command write
- outb %al, $0x64
- call empty_8042
-
- movb $0xDF, %al # A20 on
- outb %al, $0x60
- call empty_8042
-
-#ifndef CONFIG_X86_VOYAGER
- # Wait until a20 really *is* enabled; it can take a fair amount of
- # time on certain systems; Toshiba Tecras are known to have this
- # problem.
-a20_kbc_wait:
- xorw %cx, %cx
-a20_kbc_wait_loop:
- call a20_test
- jnz a20_done
- loop a20_kbc_wait_loop
-
- # Final attempt: use "configuration port A"
-a20_fast:
- inb $0x92, %al # Configuration Port A
- orb $0x02, %al # "fast A20" version
- andb $0xFE, %al # don't accidentally reset
- outb %al, $0x92
-
- # Wait for configuration port A to take effect
-a20_fast_wait:
- xorw %cx, %cx
-a20_fast_wait_loop:
- call a20_test
- jnz a20_done
- loop a20_fast_wait_loop
-
- # A20 is still not responding. Try frobbing it again.
- #
- decb (a20_tries)
- jnz a20_try_loop
-
- movw $a20_err_msg, %si
- call prtstr
-
-a20_die:
- hlt
- jmp a20_die
-
-a20_tries:
- .byte A20_ENABLE_LOOPS
-
-a20_err_msg:
- .ascii "linux: fatal error: A20 gate not responding!"
- .byte 13, 10, 0
-
- # If we get here, all is good
-a20_done:
-
-#endif /* CONFIG_X86_VOYAGER */
-# set up gdt and idt and 32bit start address
- lidt idt_48 # load idt with 0,0
- xorl %eax, %eax # Compute gdt_base
- movw %ds, %ax # (Convert %ds:gdt to a linear ptr)
- shll $4, %eax
- addl %eax, code32
- addl $gdt, %eax
- movl %eax, (gdt_48+2)
- lgdt gdt_48 # load gdt with whatever is
- # appropriate
-
-# make sure any possible coprocessor is properly reset..
- xorw %ax, %ax
- outb %al, $0xf0
- call delay
-
- outb %al, $0xf1
- call delay
-
-# well, that went ok, I hope. Now we mask all interrupts - the rest
-# is done in init_IRQ().
- movb $0xFF, %al # mask all interrupts for now
- outb %al, $0xA1
- call delay
-
- movb $0xFB, %al # mask all irq's but irq2 which
- outb %al, $0x21 # is cascaded
-
-# Well, that certainly wasn't fun :-(. Hopefully it works, and we don't
-# need no steenking BIOS anyway (except for the initial loading :-).
-# The BIOS-routine wants lots of unnecessary data, and it's less
-# "interesting" anyway. This is how REAL programmers do it.
-#
-# Well, now's the time to actually move into protected mode. To make
-# things as simple as possible, we do no register set-up or anything,
-# we let the gnu-compiled 32-bit programs do that. We just jump to
-# absolute address 0x1000 (or the loader supplied one),
-# in 32-bit protected mode.
-#
-# Note that the short jump isn't strictly needed, although there are
-# reasons why it might be a good idea. It won't hurt in any case.
- movw $1, %ax # protected mode (PE) bit
- lmsw %ax # This is it!
- jmp flush_instr
-
-flush_instr:
- xorw %bx, %bx # Flag to indicate a boot
- xorl %esi, %esi # Pointer to real-mode code
- movw %cs, %si
- subw $DELTA_INITSEG, %si
- shll $4, %esi # Convert to 32-bit pointer
-
-# jump to startup_32 in arch/i386/boot/compressed/head.S
-#
-# NOTE: For high loaded big kernels we need a
-# jmpi 0x100000,__BOOT_CS
-#
-# but we yet haven't reloaded the CS register, so the default size
-# of the target offset still is 16 bit.
-# However, using an operand prefix (0x66), the CPU will properly
-# take our 48 bit far pointer. (INTeL 80386 Programmer's Reference
-# Manual, Mixing 16-bit and 32-bit code, page 16-6)
-
- .byte 0x66, 0xea # prefix + jmpi-opcode
-code32: .long startup_32 # will be set to %cs+startup_32
- .word __BOOT_CS
-.code32
-startup_32:
- movl $(__BOOT_DS), %eax
- movl %eax, %ds
- movl %eax, %es
- movl %eax, %fs
- movl %eax, %gs
- movl %eax, %ss
-
- xorl %eax, %eax
-1: incl %eax # check that A20 really IS enabled
- movl %eax, 0x00000000 # loop forever if it isn't
- cmpl %eax, 0x00100000
- je 1b
-
- # Jump to the 32bit entry point
- jmpl *(code32_start - start + (DELTA_INITSEG << 4))(%esi)
-.code16
-
-# Here's a bunch of information about your current kernel..
-kernel_version: .ascii UTS_RELEASE
- .ascii " ("
- .ascii LINUX_COMPILE_BY
- .ascii "@"
- .ascii LINUX_COMPILE_HOST
- .ascii ") "
- .ascii UTS_VERSION
- .byte 0
-
-# This is the default real mode switch routine.
-# to be called just before protected mode transition
-default_switch:
- cli # no interrupts allowed !
- movb $0x80, %al # disable NMI for bootup
- # sequence
- outb %al, $0x70
- lret
-
-
-#ifndef CONFIG_X86_VOYAGER
-# This routine tests whether or not A20 is enabled. If so, it
-# exits with zf = 0.
-#
-# The memory address used, 0x200, is the int $0x80 vector, which
-# should be safe.
-
-A20_TEST_ADDR = 4*0x80
-
-a20_test:
- pushw %cx
- pushw %ax
- xorw %cx, %cx
- movw %cx, %fs # Low memory
- decw %cx
- movw %cx, %gs # High memory area
- movw $A20_TEST_LOOPS, %cx
- movw %fs:(A20_TEST_ADDR), %ax
- pushw %ax
-a20_test_wait:
- incw %ax
- movw %ax, %fs:(A20_TEST_ADDR)
- call delay # Serialize and make delay constant
- cmpw %gs:(A20_TEST_ADDR+0x10), %ax
- loope a20_test_wait
-
- popw %fs:(A20_TEST_ADDR)
- popw %ax
- popw %cx
- ret
-
-#endif /* CONFIG_X86_VOYAGER */
-
-# This routine checks that the keyboard command queue is empty
-# (after emptying the output buffers)
-#
-# Some machines have delusions that the keyboard buffer is always full
-# with no keyboard attached...
-#
-# If there is no keyboard controller, we will usually get 0xff
-# to all the reads. With each IO taking a microsecond and
-# a timeout of 100,000 iterations, this can take about half a
-# second ("delay" == outb to port 0x80). That should be ok,
-# and should also be plenty of time for a real keyboard controller
-# to empty.
-#
-
-empty_8042:
- pushl %ecx
- movl $100000, %ecx
-
-empty_8042_loop:
- decl %ecx
- jz empty_8042_end_loop
-
- call delay
-
- inb $0x64, %al # 8042 status port
- testb $1, %al # output buffer?
- jz no_output
-
- call delay
- inb $0x60, %al # read it
- jmp empty_8042_loop
-
-no_output:
- testb $2, %al # is input buffer full?
- jnz empty_8042_loop # yes - loop
-empty_8042_end_loop:
- popl %ecx
- ret
-
-# Read the cmos clock. Return the seconds in al
-gettime:
- pushw %cx
- movb $0x02, %ah
- int $0x1a
- movb %dh, %al # %dh contains the seconds
- andb $0x0f, %al
- movb %dh, %ah
- movb $0x04, %cl
- shrb %cl, %ah
- aad
- popw %cx
- ret
-
-# Delay is needed after doing I/O
-delay:
- outb %al,$0x80
- ret
-
-# Descriptor tables
-#
-# NOTE: The intel manual says gdt should be sixteen bytes aligned for
-# efficiency reasons. However, there are machines which are known not
-# to boot with misaligned GDTs, so alter this at your peril! If you alter
-# GDT_ENTRY_BOOT_CS (in asm/segment.h) remember to leave at least two
-# empty GDT entries (one for NULL and one reserved).
-#
-# NOTE: On some CPUs, the GDT must be 8 byte aligned. This is
-# true for the Voyager Quad CPU card which will not boot without
-# This directive. 16 byte aligment is recommended by intel.
-#
- .align 16
-gdt:
- .fill GDT_ENTRY_BOOT_CS,8,0
-
- .word 0xFFFF # 4Gb - (0x100000*0x1000 = 4Gb)
- .word 0 # base address = 0
- .word 0x9A00 # code read/exec
- .word 0x00CF # granularity = 4096, 386
- # (+5th nibble of limit)
-
- .word 0xFFFF # 4Gb - (0x100000*0x1000 = 4Gb)
- .word 0 # base address = 0
- .word 0x9200 # data read/write
- .word 0x00CF # granularity = 4096, 386
- # (+5th nibble of limit)
-gdt_end:
- .align 4
-
- .word 0 # alignment byte
-idt_48:
- .word 0 # idt limit = 0
- .word 0, 0 # idt base = 0L
-
- .word 0 # alignment byte
-gdt_48:
- .word gdt_end - gdt - 1 # gdt limit
- .word 0, 0 # gdt base (filled in later)
-
-# Include video setup & detection code
-
-#include "video.S"
-
-# Setup signature -- must be last
-setup_sig1: .word SIG1
-setup_sig2: .word SIG2
-
-# After this point, there is some free space which is used by the video mode
-# handling code to store the temporary mode table (not used by the kernel).
-
-modelist:
-
-.text
-endtext:
-.data
-enddata:
-.bss
-endbss:
diff --git a/arch/i386/boot/video.S b/arch/i386/boot/video.S
deleted file mode 100644
index 8143c95..0000000
--- a/arch/i386/boot/video.S
+++ /dev/null
@@ -1,2043 +0,0 @@
-/* video.S
- *
- * Display adapter & video mode setup, version 2.13 (14-May-99)
- *
- * Copyright (C) 1995 -- 1998 Martin Mares <mj@ucw.cz>
- * Based on the original setup.S code (C) Linus Torvalds and Mats Anderson
- *
- * Rewritten to use GNU 'as' by Chris Noe <stiker@northlink.com> May 1999
- *
- * For further information, look at Documentation/svga.txt.
- *
- */
-
-/* Enable autodetection of SVGA adapters and modes. */
-#undef CONFIG_VIDEO_SVGA
-
-/* Enable autodetection of VESA modes */
-#define CONFIG_VIDEO_VESA
-
-/* Enable compacting of mode table */
-#define CONFIG_VIDEO_COMPACT
-
-/* Retain screen contents when switching modes */
-#define CONFIG_VIDEO_RETAIN
-
-/* Enable local mode list */
-#undef CONFIG_VIDEO_LOCAL
-
-/* Force 400 scan lines for standard modes (hack to fix bad BIOS behaviour */
-#undef CONFIG_VIDEO_400_HACK
-
-/* Hack that lets you force specific BIOS mode ID and specific dimensions */
-#undef CONFIG_VIDEO_GFX_HACK
-#define VIDEO_GFX_BIOS_AX 0x4f02 /* 800x600 on ThinkPad */
-#define VIDEO_GFX_BIOS_BX 0x0102
-#define VIDEO_GFX_DUMMY_RESOLUTION 0x6425 /* 100x37 */
-
-/* This code uses an extended set of video mode numbers. These include:
- * Aliases for standard modes
- * NORMAL_VGA (-1)
- * EXTENDED_VGA (-2)
- * ASK_VGA (-3)
- * Video modes numbered by menu position -- NOT RECOMMENDED because of lack
- * of compatibility when extending the table. These are between 0x00 and 0xff.
- */
-#define VIDEO_FIRST_MENU 0x0000
-
-/* Standard BIOS video modes (BIOS number + 0x0100) */
-#define VIDEO_FIRST_BIOS 0x0100
-
-/* VESA BIOS video modes (VESA number + 0x0200) */
-#define VIDEO_FIRST_VESA 0x0200
-
-/* Video7 special modes (BIOS number + 0x0900) */
-#define VIDEO_FIRST_V7 0x0900
-
-/* Special video modes */
-#define VIDEO_FIRST_SPECIAL 0x0f00
-#define VIDEO_80x25 0x0f00
-#define VIDEO_8POINT 0x0f01
-#define VIDEO_80x43 0x0f02
-#define VIDEO_80x28 0x0f03
-#define VIDEO_CURRENT_MODE 0x0f04
-#define VIDEO_80x30 0x0f05
-#define VIDEO_80x34 0x0f06
-#define VIDEO_80x60 0x0f07
-#define VIDEO_GFX_HACK 0x0f08
-#define VIDEO_LAST_SPECIAL 0x0f09
-
-/* Video modes given by resolution */
-#define VIDEO_FIRST_RESOLUTION 0x1000
-
-/* The "recalculate timings" flag */
-#define VIDEO_RECALC 0x8000
-
-/* Positions of various video parameters passed to the kernel */
-/* (see also include/linux/tty.h) */
-#define PARAM_CURSOR_POS 0x00
-#define PARAM_VIDEO_PAGE 0x04
-#define PARAM_VIDEO_MODE 0x06
-#define PARAM_VIDEO_COLS 0x07
-#define PARAM_VIDEO_EGA_BX 0x0a
-#define PARAM_VIDEO_LINES 0x0e
-#define PARAM_HAVE_VGA 0x0f
-#define PARAM_FONT_POINTS 0x10
-
-#define PARAM_LFB_WIDTH 0x12
-#define PARAM_LFB_HEIGHT 0x14
-#define PARAM_LFB_DEPTH 0x16
-#define PARAM_LFB_BASE 0x18
-#define PARAM_LFB_SIZE 0x1c
-#define PARAM_LFB_LINELENGTH 0x24
-#define PARAM_LFB_COLORS 0x26
-#define PARAM_VESAPM_SEG 0x2e
-#define PARAM_VESAPM_OFF 0x30
-#define PARAM_LFB_PAGES 0x32
-#define PARAM_VESA_ATTRIB 0x34
-#define PARAM_CAPABILITIES 0x36
-
-/* Define DO_STORE according to CONFIG_VIDEO_RETAIN */
-#ifdef CONFIG_VIDEO_RETAIN
-#define DO_STORE call store_screen
-#else
-#define DO_STORE
-#endif /* CONFIG_VIDEO_RETAIN */
-
-# This is the main entry point called by setup.S
-# %ds *must* be pointing to the bootsector
-video: pushw %ds # We use different segments
- pushw %ds # FS contains original DS
- popw %fs
- pushw %cs # DS is equal to CS
- popw %ds
- pushw %cs # ES is equal to CS
- popw %es
- xorw %ax, %ax
- movw %ax, %gs # GS is zero
- cld
- call basic_detect # Basic adapter type testing (EGA/VGA/MDA/CGA)
-#ifdef CONFIG_VIDEO_SELECT
- movw %fs:(0x01fa), %ax # User selected video mode
- cmpw $ASK_VGA, %ax # Bring up the menu
- jz vid2
-
- call mode_set # Set the mode
- jc vid1
-
- leaw badmdt, %si # Invalid mode ID
- call prtstr
-vid2: call mode_menu
-vid1:
-#ifdef CONFIG_VIDEO_RETAIN
- call restore_screen # Restore screen contents
-#endif /* CONFIG_VIDEO_RETAIN */
- call store_edid
-#endif /* CONFIG_VIDEO_SELECT */
- call mode_params # Store mode parameters
- popw %ds # Restore original DS
- ret
-
-# Detect if we have CGA, MDA, EGA or VGA and pass it to the kernel.
-basic_detect:
- movb $0, %fs:(PARAM_HAVE_VGA)
- movb $0x12, %ah # Check EGA/VGA
- movb $0x10, %bl
- int $0x10
- movw %bx, %fs:(PARAM_VIDEO_EGA_BX) # Identifies EGA to the kernel
- cmpb $0x10, %bl # No, it's a CGA/MDA/HGA card.
- je basret
-
- incb adapter
- movw $0x1a00, %ax # Check EGA or VGA?
- int $0x10
- cmpb $0x1a, %al # 1a means VGA...
- jne basret # anything else is EGA.
-
- incb %fs:(PARAM_HAVE_VGA) # We've detected a VGA
- incb adapter
-basret: ret
-
-# Store the video mode parameters for later usage by the kernel.
-# This is done by asking the BIOS except for the rows/columns
-# parameters in the default 80x25 mode -- these are set directly,
-# because some very obscure BIOSes supply insane values.
-mode_params:
-#ifdef CONFIG_VIDEO_SELECT
- cmpb $0, graphic_mode
- jnz mopar_gr
-#endif
- movb $0x03, %ah # Read cursor position
- xorb %bh, %bh
- int $0x10
- movw %dx, %fs:(PARAM_CURSOR_POS)
- movb $0x0f, %ah # Read page/mode/width
- int $0x10
- movw %bx, %fs:(PARAM_VIDEO_PAGE)
- movw %ax, %fs:(PARAM_VIDEO_MODE) # Video mode and screen width
- cmpb $0x7, %al # MDA/HGA => segment differs
- jnz mopar0
-
- movw $0xb000, video_segment
-mopar0: movw %gs:(0x485), %ax # Font size
- movw %ax, %fs:(PARAM_FONT_POINTS) # (valid only on EGA/VGA)
- movw force_size, %ax # Forced size?
- orw %ax, %ax
- jz mopar1
-
- movb %ah, %fs:(PARAM_VIDEO_COLS)
- movb %al, %fs:(PARAM_VIDEO_LINES)
- ret
-
-mopar1: movb $25, %al
- cmpb $0, adapter # If we are on CGA/MDA/HGA, the
- jz mopar2 # screen must have 25 lines.
-
- movb %gs:(0x484), %al # On EGA/VGA, use the EGA+ BIOS
- incb %al # location of max lines.
-mopar2: movb %al, %fs:(PARAM_VIDEO_LINES)
- ret
-
-#ifdef CONFIG_VIDEO_SELECT
-# Fetching of VESA frame buffer parameters
-mopar_gr:
- leaw modelist+1024, %di
- movb $0x23, %fs:(PARAM_HAVE_VGA)
- movw 16(%di), %ax
- movw %ax, %fs:(PARAM_LFB_LINELENGTH)
- movw 18(%di), %ax
- movw %ax, %fs:(PARAM_LFB_WIDTH)
- movw 20(%di), %ax
- movw %ax, %fs:(PARAM_LFB_HEIGHT)
- movb 25(%di), %al
- movb $0, %ah
- movw %ax, %fs:(PARAM_LFB_DEPTH)
- movb 29(%di), %al
- movb $0, %ah
- movw %ax, %fs:(PARAM_LFB_PAGES)
- movl 40(%di), %eax
- movl %eax, %fs:(PARAM_LFB_BASE)
- movl 31(%di), %eax
- movl %eax, %fs:(PARAM_LFB_COLORS)
- movl 35(%di), %eax
- movl %eax, %fs:(PARAM_LFB_COLORS+4)
- movw 0(%di), %ax
- movw %ax, %fs:(PARAM_VESA_ATTRIB)
-
-# get video mem size
- leaw modelist+1024, %di
- movw $0x4f00, %ax
- int $0x10
- xorl %eax, %eax
- movw 18(%di), %ax
- movl %eax, %fs:(PARAM_LFB_SIZE)
-
-# store mode capabilities
- movl 10(%di), %eax
- movl %eax, %fs:(PARAM_CAPABILITIES)
-
-# switching the DAC to 8-bit is for <= 8 bpp only
- movw %fs:(PARAM_LFB_DEPTH), %ax
- cmpw $8, %ax
- jg dac_done
-
-# get DAC switching capability
- xorl %eax, %eax
- movb 10(%di), %al
- testb $1, %al
- jz dac_set
-
-# attempt to switch DAC to 8-bit
- movw $0x4f08, %ax
- movw $0x0800, %bx
- int $0x10
- cmpw $0x004f, %ax
- jne dac_set
- movb %bh, dac_size # store actual DAC size
-
-dac_set:
-# set color size to DAC size
- movb dac_size, %al
- movb %al, %fs:(PARAM_LFB_COLORS+0)
- movb %al, %fs:(PARAM_LFB_COLORS+2)
- movb %al, %fs:(PARAM_LFB_COLORS+4)
- movb %al, %fs:(PARAM_LFB_COLORS+6)
-
-# set color offsets to 0
- movb $0, %fs:(PARAM_LFB_COLORS+1)
- movb $0, %fs:(PARAM_LFB_COLORS+3)
- movb $0, %fs:(PARAM_LFB_COLORS+5)
- movb $0, %fs:(PARAM_LFB_COLORS+7)
-
-dac_done:
-# get protected mode interface informations
- movw $0x4f0a, %ax
- xorw %bx, %bx
- xorw %di, %di
- int $0x10
- cmp $0x004f, %ax
- jnz no_pm
-
- movw %es, %fs:(PARAM_VESAPM_SEG)
- movw %di, %fs:(PARAM_VESAPM_OFF)
-no_pm: ret
-
-# The video mode menu
-mode_menu:
- leaw keymsg, %si # "Return/Space/Timeout" message
- call prtstr
- call flush
-nokey: call getkt
-
- cmpb $0x0d, %al # ENTER ?
- je listm # yes - manual mode selection
-
- cmpb $0x20, %al # SPACE ?
- je defmd1 # no - repeat
-
- call beep
- jmp nokey
-
-defmd1: ret # No mode chosen? Default 80x25
-
-listm: call mode_table # List mode table
-listm0: leaw name_bann, %si # Print adapter name
- call prtstr
- movw card_name, %si
- orw %si, %si
- jnz an2
-
- movb adapter, %al
- leaw old_name, %si
- orb %al, %al
- jz an1
-
- leaw ega_name, %si
- decb %al
- jz an1
-
- leaw vga_name, %si
- jmp an1
-
-an2: call prtstr
- leaw svga_name, %si
-an1: call prtstr
- leaw listhdr, %si # Table header
- call prtstr
- movb $0x30, %dl # DL holds mode number
- leaw modelist, %si
-lm1: cmpw $ASK_VGA, (%si) # End?
- jz lm2
-
- movb %dl, %al # Menu selection number
- call prtchr
- call prtsp2
- lodsw
- call prthw # Mode ID
- call prtsp2
- movb 0x1(%si), %al
- call prtdec # Rows
- movb $0x78, %al # the letter 'x'
- call prtchr
- lodsw
- call prtdec # Columns
- movb $0x0d, %al # New line
- call prtchr
- movb $0x0a, %al
- call prtchr
- incb %dl # Next character
- cmpb $0x3a, %dl
- jnz lm1
-
- movb $0x61, %dl
- jmp lm1
-
-lm2: leaw prompt, %si # Mode prompt
- call prtstr
- leaw edit_buf, %di # Editor buffer
-lm3: call getkey
- cmpb $0x0d, %al # Enter?
- jz lment
-
- cmpb $0x08, %al # Backspace?
- jz lmbs
-
- cmpb $0x20, %al # Printable?
- jc lm3
-
- cmpw $edit_buf+4, %di # Enough space?
- jz lm3
-
- stosb
- call prtchr
- jmp lm3
-
-lmbs: cmpw $edit_buf, %di # Backspace
- jz lm3
-
- decw %di
- movb $0x08, %al
- call prtchr
- call prtspc
- movb $0x08, %al
- call prtchr
- jmp lm3
-
-lment: movb $0, (%di)
- leaw crlft, %si
- call prtstr
- leaw edit_buf, %si
- cmpb $0, (%si) # Empty string = default mode
- jz lmdef
-
- cmpb $0, 1(%si) # One character = menu selection
- jz mnusel
-
- cmpw $0x6373, (%si) # "scan" => mode scanning
- jnz lmhx
-
- cmpw $0x6e61, 2(%si)
- jz lmscan
-
-lmhx: xorw %bx, %bx # Else => mode ID in hex
-lmhex: lodsb
- orb %al, %al
- jz lmuse1
-
- subb $0x30, %al
- jc lmbad
-
- cmpb $10, %al
- jc lmhx1
-
- subb $7, %al
- andb $0xdf, %al
- cmpb $10, %al
- jc lmbad
-
- cmpb $16, %al
- jnc lmbad
-
-lmhx1: shlw $4, %bx
- orb %al, %bl
- jmp lmhex
-
-lmuse1: movw %bx, %ax
- jmp lmuse
-
-mnusel: lodsb # Menu selection
- xorb %ah, %ah
- subb $0x30, %al
- jc lmbad
-
- cmpb $10, %al
- jc lmuse
-
- cmpb $0x61-0x30, %al
- jc lmbad
-
- subb $0x61-0x30-10, %al
- cmpb $36, %al
- jnc lmbad
-
-lmuse: call mode_set
- jc lmdef
-
-lmbad: leaw unknt, %si
- call prtstr
- jmp lm2
-lmscan: cmpb $0, adapter # Scanning only on EGA/VGA
- jz lmbad
-
- movw $0, mt_end # Scanning of modes is
- movb $1, scanning # done as new autodetection.
- call mode_table
- jmp listm0
-lmdef: ret
-
-# Additional parts of mode_set... (relative jumps, you know)
-setv7: # Video7 extended modes
- DO_STORE
- subb $VIDEO_FIRST_V7>>8, %bh
- movw $0x6f05, %ax
- int $0x10
- stc
- ret
-
-_setrec: jmp setrec # Ugly...
-_set_80x25: jmp set_80x25
-
-# Aliases for backward compatibility.
-setalias:
- movw $VIDEO_80x25, %ax
- incw %bx
- jz mode_set
-
- movb $VIDEO_8POINT-VIDEO_FIRST_SPECIAL, %al
- incw %bx
- jnz setbad # Fall-through!
-
-# Setting of user mode (AX=mode ID) => CF=success
-mode_set:
- movw %ax, %fs:(0x01fa) # Store mode for use in acpi_wakeup.S
- movw %ax, %bx
- cmpb $0xff, %ah
- jz setalias
-
- testb $VIDEO_RECALC>>8, %ah
- jnz _setrec
-
- cmpb $VIDEO_FIRST_RESOLUTION>>8, %ah
- jnc setres
-
- cmpb $VIDEO_FIRST_SPECIAL>>8, %ah
- jz setspc
-
- cmpb $VIDEO_FIRST_V7>>8, %ah
- jz setv7
-
- cmpb $VIDEO_FIRST_VESA>>8, %ah
- jnc check_vesa
-
- orb %ah, %ah
- jz setmenu
-
- decb %ah
- jz setbios
-
-setbad: clc
- movb $0, do_restore # The screen needn't be restored
- ret
-
-setvesa:
- DO_STORE
- subb $VIDEO_FIRST_VESA>>8, %bh
- movw $0x4f02, %ax # VESA BIOS mode set call
- int $0x10
- cmpw $0x004f, %ax # AL=4f if implemented
- jnz setbad # AH=0 if OK
-
- stc
- ret
-
-setbios:
- DO_STORE
- int $0x10 # Standard BIOS mode set call
- pushw %bx
- movb $0x0f, %ah # Check if really set
- int $0x10
- popw %bx
- cmpb %bl, %al
- jnz setbad
-
- stc
- ret
-
-setspc: xorb %bh, %bh # Set special mode
- cmpb $VIDEO_LAST_SPECIAL-VIDEO_FIRST_SPECIAL, %bl
- jnc setbad
-
- addw %bx, %bx
- jmp *spec_inits(%bx)
-
-setmenu:
- orb %al, %al # 80x25 is an exception
- jz _set_80x25
-
- pushw %bx # Set mode chosen from menu
- call mode_table # Build the mode table
- popw %ax
- shlw $2, %ax
- addw %ax, %si
- cmpw %di, %si
- jnc setbad
-
- movw (%si), %ax # Fetch mode ID
-_m_s: jmp mode_set
-
-setres: pushw %bx # Set mode chosen by resolution
- call mode_table
- popw %bx
- xchgb %bl, %bh
-setr1: lodsw
- cmpw $ASK_VGA, %ax # End of the list?
- jz setbad
-
- lodsw
- cmpw %bx, %ax
- jnz setr1
-
- movw -4(%si), %ax # Fetch mode ID
- jmp _m_s
-
-check_vesa:
-#ifdef CONFIG_FIRMWARE_EDID
- leaw modelist+1024, %di
- movw $0x4f00, %ax
- int $0x10
- cmpw $0x004f, %ax
- jnz setbad
-
- movw 4(%di), %ax
- movw %ax, vbe_version
-#endif
- leaw modelist+1024, %di
- subb $VIDEO_FIRST_VESA>>8, %bh
- movw %bx, %cx # Get mode information structure
- movw $0x4f01, %ax
- int $0x10
- addb $VIDEO_FIRST_VESA>>8, %bh
- cmpw $0x004f, %ax
- jnz setbad
-
- movb (%di), %al # Check capabilities.
- andb $0x19, %al
- cmpb $0x09, %al
- jz setvesa # This is a text mode
-
- movb (%di), %al # Check capabilities.
- andb $0x99, %al
- cmpb $0x99, %al
- jnz _setbad # Doh! No linear frame buffer.
-
- subb $VIDEO_FIRST_VESA>>8, %bh
- orw $0x4000, %bx # Use linear frame buffer
- movw $0x4f02, %ax # VESA BIOS mode set call
- int $0x10
- cmpw $0x004f, %ax # AL=4f if implemented
- jnz _setbad # AH=0 if OK
-
- movb $1, graphic_mode # flag graphic mode
- movb $0, do_restore # no screen restore
- stc
- ret
-
-_setbad: jmp setbad # Ugly...
-
-# Recalculate vertical display end registers -- this fixes various
-# inconsistencies of extended modes on many adapters. Called when
-# the VIDEO_RECALC flag is set in the mode ID.
-
-setrec: subb $VIDEO_RECALC>>8, %ah # Set the base mode
- call mode_set
- jnc rct3
-
- movw %gs:(0x485), %ax # Font size in pixels
- movb %gs:(0x484), %bl # Number of rows
- incb %bl
- mulb %bl # Number of visible
- decw %ax # scan lines - 1
- movw $0x3d4, %dx
- movw %ax, %bx
- movb $0x12, %al # Lower 8 bits
- movb %bl, %ah
- outw %ax, %dx
- movb $0x07, %al # Bits 8 and 9 in the overflow register
- call inidx
- xchgb %al, %ah
- andb $0xbd, %ah
- shrb %bh
- jnc rct1
- orb $0x02, %ah
-rct1: shrb %bh
- jnc rct2
- orb $0x40, %ah
-rct2: movb $0x07, %al
- outw %ax, %dx
- stc
-rct3: ret
-
-# Table of routines for setting of the special modes.
-spec_inits:
- .word set_80x25
- .word set_8pixel
- .word set_80x43
- .word set_80x28
- .word set_current
- .word set_80x30
- .word set_80x34
- .word set_80x60
- .word set_gfx
-
-# Set the 80x25 mode. If already set, do nothing.
-set_80x25:
- movw $0x5019, force_size # Override possibly broken BIOS
-use_80x25:
-#ifdef CONFIG_VIDEO_400_HACK
- movw $0x1202, %ax # Force 400 scan lines
- movb $0x30, %bl
- int $0x10
-#else
- movb $0x0f, %ah # Get current mode ID
- int $0x10
- cmpw $0x5007, %ax # Mode 7 (80x25 mono) is the only one available
- jz st80 # on CGA/MDA/HGA and is also available on EGAM
-
- cmpw $0x5003, %ax # Unknown mode, force 80x25 color
- jnz force3
-
-st80: cmpb $0, adapter # CGA/MDA/HGA => mode 3/7 is always 80x25
- jz set80
-
- movb %gs:(0x0484), %al # This is EGA+ -- beware of 80x50 etc.
- orb %al, %al # Some buggy BIOS'es set 0 rows
- jz set80
-
- cmpb $24, %al # It's hopefully correct
- jz set80
-#endif /* CONFIG_VIDEO_400_HACK */
-force3: DO_STORE
- movw $0x0003, %ax # Forced set
- int $0x10
-set80: stc
- ret
-
-# Set the 80x50/80x43 8-pixel mode. Simple BIOS calls.
-set_8pixel:
- DO_STORE
- call use_80x25 # The base is 80x25
-set_8pt:
- movw $0x1112, %ax # Use 8x8 font
- xorb %bl, %bl
- int $0x10
- movw $0x1200, %ax # Use alternate print screen
- movb $0x20, %bl
- int $0x10
- movw $0x1201, %ax # Turn off cursor emulation
- movb $0x34, %bl
- int $0x10
- movb $0x01, %ah # Define cursor scan lines 6-7
- movw $0x0607, %cx
- int $0x10
-set_current:
- stc
- ret
-
-# Set the 80x28 mode. This mode works on all VGA's, because it's a standard
-# 80x25 mode with 14-point fonts instead of 16-point.
-set_80x28:
- DO_STORE
- call use_80x25 # The base is 80x25
-set14: movw $0x1111, %ax # Use 9x14 font
- xorb %bl, %bl
- int $0x10
- movb $0x01, %ah # Define cursor scan lines 11-12
- movw $0x0b0c, %cx
- int $0x10
- stc
- ret
-
-# Set the 80x43 mode. This mode is works on all VGA's.
-# It's a 350-scanline mode with 8-pixel font.
-set_80x43:
- DO_STORE
- movw $0x1201, %ax # Set 350 scans
- movb $0x30, %bl
- int $0x10
- movw $0x0003, %ax # Reset video mode
- int $0x10
- jmp set_8pt # Use 8-pixel font
-
-# Set the 80x30 mode (all VGA's). 480 scanlines, 16-pixel font.
-set_80x30:
- call use_80x25 # Start with real 80x25
- DO_STORE
- movw $0x3cc, %dx # Get CRTC port
- inb %dx, %al
- movb $0xd4, %dl
- rorb %al # Mono or color?
- jc set48a
-
- movb $0xb4, %dl
-set48a: movw $0x0c11, %ax # Vertical sync end (also unlocks CR0-7)
- call outidx
- movw $0x0b06, %ax # Vertical total
- call outidx
- movw $0x3e07, %ax # (Vertical) overflow
- call outidx
- movw $0xea10, %ax # Vertical sync start
- call outidx
- movw $0xdf12, %ax # Vertical display end
- call outidx
- movw $0xe715, %ax # Vertical blank start
- call outidx
- movw $0x0416, %ax # Vertical blank end
- call outidx
- pushw %dx
- movb $0xcc, %dl # Misc output register (read)
- inb %dx, %al
- movb $0xc2, %dl # (write)
- andb $0x0d, %al # Preserve clock select bits and color bit
- orb $0xe2, %al # Set correct sync polarity
- outb %al, %dx
- popw %dx
- movw $0x501e, force_size
- stc # That's all.
- ret
-
-# Set the 80x34 mode (all VGA's). 480 scans, 14-pixel font.
-set_80x34:
- call set_80x30 # Set 480 scans
- call set14 # And 14-pt font
- movw $0xdb12, %ax # VGA vertical display end
- movw $0x5022, force_size
-setvde: call outidx
- stc
- ret
-
-# Set the 80x60 mode (all VGA's). 480 scans, 8-pixel font.
-set_80x60:
- call set_80x30 # Set 480 scans
- call set_8pt # And 8-pt font
- movw $0xdf12, %ax # VGA vertical display end
- movw $0x503c, force_size
- jmp setvde
-
-# Special hack for ThinkPad graphics
-set_gfx:
-#ifdef CONFIG_VIDEO_GFX_HACK
- movw $VIDEO_GFX_BIOS_AX, %ax
- movw $VIDEO_GFX_BIOS_BX, %bx
- int $0x10
- movw $VIDEO_GFX_DUMMY_RESOLUTION, force_size
- stc
-#endif
- ret
-
-#ifdef CONFIG_VIDEO_RETAIN
-
-# Store screen contents to temporary buffer.
-store_screen:
- cmpb $0, do_restore # Already stored?
- jnz stsr
-
- testb $CAN_USE_HEAP, loadflags # Have we space for storing?
- jz stsr
-
- pushw %ax
- pushw %bx
- pushw force_size # Don't force specific size
- movw $0, force_size
- call mode_params # Obtain params of current mode
- popw force_size
- movb %fs:(PARAM_VIDEO_LINES), %ah
- movb %fs:(PARAM_VIDEO_COLS), %al
- movw %ax, %bx # BX=dimensions
- mulb %ah
- movw %ax, %cx # CX=number of characters
- addw %ax, %ax # Calculate image size
- addw $modelist+1024+4, %ax
- cmpw heap_end_ptr, %ax
- jnc sts1 # Unfortunately, out of memory
-
- movw %fs:(PARAM_CURSOR_POS), %ax # Store mode params
- leaw modelist+1024, %di
- stosw
- movw %bx, %ax
- stosw
- pushw %ds # Store the screen
- movw video_segment, %ds
- xorw %si, %si
- rep
- movsw
- popw %ds
- incb do_restore # Screen will be restored later
-sts1: popw %bx
- popw %ax
-stsr: ret
-
-# Restore screen contents from temporary buffer.
-restore_screen:
- cmpb $0, do_restore # Has the screen been stored?
- jz res1
-
- call mode_params # Get parameters of current mode
- movb %fs:(PARAM_VIDEO_LINES), %cl
- movb %fs:(PARAM_VIDEO_COLS), %ch
- leaw modelist+1024, %si # Screen buffer
- lodsw # Set cursor position
- movw %ax, %dx
- cmpb %cl, %dh
- jc res2
-
- movb %cl, %dh
- decb %dh
-res2: cmpb %ch, %dl
- jc res3
-
- movb %ch, %dl
- decb %dl
-res3: movb $0x02, %ah
- movb $0x00, %bh
- int $0x10
- lodsw # Display size
- movb %ah, %dl # DL=number of lines
- movb $0, %ah # BX=phys. length of orig. line
- movw %ax, %bx
- cmpb %cl, %dl # Too many?
- jc res4
-
- pushw %ax
- movb %dl, %al
- subb %cl, %al
- mulb %bl
- addw %ax, %si
- addw %ax, %si
- popw %ax
- movb %cl, %dl
-res4: cmpb %ch, %al # Too wide?
- jc res5
-
- movb %ch, %al # AX=width of src. line
-res5: movb $0, %cl
- xchgb %ch, %cl
- movw %cx, %bp # BP=width of dest. line
- pushw %es
- movw video_segment, %es
- xorw %di, %di # Move the data
- addw %bx, %bx # Convert BX and BP to _bytes_
- addw %bp, %bp
-res6: pushw %si
- pushw %di
- movw %ax, %cx
- rep
- movsw
- popw %di
- popw %si
- addw %bp, %di
- addw %bx, %si
- decb %dl
- jnz res6
-
- popw %es # Done
-res1: ret
-#endif /* CONFIG_VIDEO_RETAIN */
-
-# Write to indexed VGA register (AL=index, AH=data, DX=index reg. port)
-outidx: outb %al, %dx
- pushw %ax
- movb %ah, %al
- incw %dx
- outb %al, %dx
- decw %dx
- popw %ax
- ret
-
-# Build the table of video modes (stored after the setup.S code at the
-# `modelist' label. Each video mode record looks like:
-# .word MODE-ID (our special mode ID (see above))
-# .byte rows (number of rows)
-# .byte columns (number of columns)
-# Returns address of the end of the table in DI, the end is marked
-# with a ASK_VGA ID.
-mode_table:
- movw mt_end, %di # Already filled?
- orw %di, %di
- jnz mtab1x
-
- leaw modelist, %di # Store standard modes:
- movl $VIDEO_80x25 + 0x50190000, %eax # The 80x25 mode (ALL)
- stosl
- movb adapter, %al # CGA/MDA/HGA -- no more modes
- orb %al, %al
- jz mtabe
-
- decb %al
- jnz mtabv
-
- movl $VIDEO_8POINT + 0x502b0000, %eax # The 80x43 EGA mode
- stosl
- jmp mtabe
-
-mtab1x: jmp mtab1
-
-mtabv: leaw vga_modes, %si # All modes for std VGA
- movw $vga_modes_end-vga_modes, %cx
- rep # I'm unable to use movsw as I don't know how to store a half
- movsb # of the expression above to cx without using explicit shr.
-
- cmpb $0, scanning # Mode scan requested?
- jz mscan1
-
- call mode_scan
-mscan1:
-
-#ifdef CONFIG_VIDEO_LOCAL
- call local_modes
-#endif /* CONFIG_VIDEO_LOCAL */
-
-#ifdef CONFIG_VIDEO_VESA
- call vesa_modes # Detect VESA VGA modes
-#endif /* CONFIG_VIDEO_VESA */
-
-#ifdef CONFIG_VIDEO_SVGA
- cmpb $0, scanning # Bypass when scanning
- jnz mscan2
-
- call svga_modes # Detect SVGA cards & modes
-mscan2:
-#endif /* CONFIG_VIDEO_SVGA */
-
-mtabe:
-
-#ifdef CONFIG_VIDEO_COMPACT
- leaw modelist, %si
- movw %di, %dx
- movw %si, %di
-cmt1: cmpw %dx, %si # Scan all modes
- jz cmt2
-
- leaw modelist, %bx # Find in previous entries
- movw 2(%si), %cx
-cmt3: cmpw %bx, %si
- jz cmt4
-
- cmpw 2(%bx), %cx # Found => don't copy this entry
- jz cmt5
-
- addw $4, %bx
- jmp cmt3
-
-cmt4: movsl # Copy entry
- jmp cmt1
-
-cmt5: addw $4, %si # Skip entry
- jmp cmt1
-
-cmt2:
-#endif /* CONFIG_VIDEO_COMPACT */
-
- movw $ASK_VGA, (%di) # End marker
- movw %di, mt_end
-mtab1: leaw modelist, %si # SI=mode list, DI=list end
-ret0: ret
-
-# Modes usable on all standard VGAs
-vga_modes:
- .word VIDEO_8POINT
- .word 0x5032 # 80x50
- .word VIDEO_80x43
- .word 0x502b # 80x43
- .word VIDEO_80x28
- .word 0x501c # 80x28
- .word VIDEO_80x30
- .word 0x501e # 80x30
- .word VIDEO_80x34
- .word 0x5022 # 80x34
- .word VIDEO_80x60
- .word 0x503c # 80x60
-#ifdef CONFIG_VIDEO_GFX_HACK
- .word VIDEO_GFX_HACK
- .word VIDEO_GFX_DUMMY_RESOLUTION
-#endif
-
-vga_modes_end:
-# Detect VESA modes.
-
-#ifdef CONFIG_VIDEO_VESA
-vesa_modes:
- cmpb $2, adapter # VGA only
- jnz ret0
-
- movw %di, %bp # BP=original mode table end
- addw $0x200, %di # Buffer space
- movw $0x4f00, %ax # VESA Get card info call
- int $0x10
- movw %bp, %di
- cmpw $0x004f, %ax # Successful?
- jnz ret0
-
- cmpw $0x4556, 0x200(%di)
- jnz ret0
-
- cmpw $0x4153, 0x202(%di)
- jnz ret0
-
- movw $vesa_name, card_name # Set name to "VESA VGA"
- pushw %gs
- lgsw 0x20e(%di), %si # GS:SI=mode list
- movw $128, %cx # Iteration limit
-vesa1:
-# gas version 2.9.1, using BFD version 2.9.1.0.23 buggers the next inst.
-# XXX: lodsw %gs:(%si), %ax # Get next mode in the list
- gs; lodsw
- cmpw $0xffff, %ax # End of the table?
- jz vesar
-
- cmpw $0x0080, %ax # Check validity of mode ID
- jc vesa2
-
- orb %ah, %ah # Valid IDs: 0x0000-0x007f/0x0100-0x07ff
- jz vesan # Certain BIOSes report 0x80-0xff!
-
- cmpw $0x0800, %ax
- jnc vesae
-
-vesa2: pushw %cx
- movw %ax, %cx # Get mode information structure
- movw $0x4f01, %ax
- int $0x10
- movw %cx, %bx # BX=mode number
- addb $VIDEO_FIRST_VESA>>8, %bh
- popw %cx
- cmpw $0x004f, %ax
- jnz vesan # Don't report errors (buggy BIOSES)
-
- movb (%di), %al # Check capabilities. We require
- andb $0x19, %al # a color text mode.
- cmpb $0x09, %al
- jnz vesan
-
- cmpw $0xb800, 8(%di) # Standard video memory address required
- jnz vesan
-
- testb $2, (%di) # Mode characteristics supplied?
- movw %bx, (%di) # Store mode number
- jz vesa3
-
- xorw %dx, %dx
- movw 0x12(%di), %bx # Width
- orb %bh, %bh
- jnz vesan
-
- movb %bl, 0x3(%di)
- movw 0x14(%di), %ax # Height
- orb %ah, %ah
- jnz vesan
-
- movb %al, 2(%di)
- mulb %bl
- cmpw $8193, %ax # Small enough for Linux console driver?
- jnc vesan
-
- jmp vesaok
-
-vesa3: subw $0x8108, %bx # This mode has no detailed info specified,
- jc vesan # so it must be a standard VESA mode.
-
- cmpw $5, %bx
- jnc vesan
-
- movw vesa_text_mode_table(%bx), %ax
- movw %ax, 2(%di)
-vesaok: addw $4, %di # The mode is valid. Store it.
-vesan: loop vesa1 # Next mode. Limit exceeded => error
-vesae: leaw vesaer, %si
- call prtstr
- movw %bp, %di # Discard already found modes.
-vesar: popw %gs
- ret
-
-# Dimensions of standard VESA text modes
-vesa_text_mode_table:
- .byte 60, 80 # 0108
- .byte 25, 132 # 0109
- .byte 43, 132 # 010A
- .byte 50, 132 # 010B
- .byte 60, 132 # 010C
-#endif /* CONFIG_VIDEO_VESA */
-
-# Scan for video modes. A bit dirty, but should work.
-mode_scan:
- movw $0x0100, %cx # Start with mode 0
-scm1: movb $0, %ah # Test the mode
- movb %cl, %al
- int $0x10
- movb $0x0f, %ah
- int $0x10
- cmpb %cl, %al
- jnz scm2 # Mode not set
-
- movw $0x3c0, %dx # Test if it's a text mode
- movb $0x10, %al # Mode bits
- call inidx
- andb $0x03, %al
- jnz scm2
-
- movb $0xce, %dl # Another set of mode bits
- movb $0x06, %al
- call inidx
- shrb %al
- jc scm2
-
- movb $0xd4, %dl # Cursor location
- movb $0x0f, %al
- call inidx
- orb %al, %al
- jnz scm2
-
- movw %cx, %ax # Ok, store the mode
- stosw
- movb %gs:(0x484), %al # Number of rows
- incb %al
- stosb
- movw %gs:(0x44a), %ax # Number of columns
- stosb
-scm2: incb %cl
- jns scm1
-
- movw $0x0003, %ax # Return back to mode 3
- int $0x10
- ret
-
-tstidx: outw %ax, %dx # OUT DX,AX and inidx
-inidx: outb %al, %dx # Read from indexed VGA register
- incw %dx # AL=index, DX=index reg port -> AL=data
- inb %dx, %al
- decw %dx
- ret
-
-# Try to detect type of SVGA card and supply (usually approximate) video
-# mode table for it.
-
-#ifdef CONFIG_VIDEO_SVGA
-svga_modes:
- leaw svga_table, %si # Test all known SVGA adapters
-dosvga: lodsw
- movw %ax, %bp # Default mode table
- orw %ax, %ax
- jz didsv1
-
- lodsw # Pointer to test routine
- pushw %si
- pushw %di
- pushw %es
- movw $0xc000, %bx
- movw %bx, %es
- call *%ax # Call test routine
- popw %es
- popw %di
- popw %si
- orw %bp, %bp
- jz dosvga
-
- movw %bp, %si # Found, copy the modes
- movb svga_prefix, %ah
-cpsvga: lodsb
- orb %al, %al
- jz didsv
-
- stosw
- movsw
- jmp cpsvga
-
-didsv: movw %si, card_name # Store pointer to card name
-didsv1: ret
-
-# Table of all known SVGA cards. For each card, we store a pointer to
-# a table of video modes supported by the card and a pointer to a routine
-# used for testing of presence of the card. The video mode table is always
-# followed by the name of the card or the chipset.
-svga_table:
- .word ati_md, ati_test
- .word oak_md, oak_test
- .word paradise_md, paradise_test
- .word realtek_md, realtek_test
- .word s3_md, s3_test
- .word chips_md, chips_test
- .word video7_md, video7_test
- .word cirrus5_md, cirrus5_test
- .word cirrus6_md, cirrus6_test
- .word cirrus1_md, cirrus1_test
- .word ahead_md, ahead_test
- .word everex_md, everex_test
- .word genoa_md, genoa_test
- .word trident_md, trident_test
- .word tseng_md, tseng_test
- .word 0
-
-# Test routines and mode tables:
-
-# S3 - The test algorithm was taken from the SuperProbe package
-# for XFree86 1.2.1. Report bugs to Christoph.Niemann@linux.org
-s3_test:
- movw $0x0f35, %cx # we store some constants in cl/ch
- movw $0x03d4, %dx
- movb $0x38, %al
- call inidx
- movb %al, %bh # store current CRT-register 0x38
- movw $0x0038, %ax
- call outidx # disable writing to special regs
- movb %cl, %al # check whether we can write special reg 0x35
- call inidx
- movb %al, %bl # save the current value of CRT reg 0x35
- andb $0xf0, %al # clear bits 0-3
- movb %al, %ah
- movb %cl, %al # and write it to CRT reg 0x35
- call outidx
- call inidx # now read it back
- andb %ch, %al # clear the upper 4 bits
- jz s3_2 # the first test failed. But we have a
-
- movb %bl, %ah # second chance
- movb %cl, %al
- call outidx
- jmp s3_1 # do the other tests
-
-s3_2: movw %cx, %ax # load ah with 0xf and al with 0x35
- orb %bl, %ah # set the upper 4 bits of ah with the orig value
- call outidx # write ...
- call inidx # ... and reread
- andb %cl, %al # turn off the upper 4 bits
- pushw %ax
- movb %bl, %ah # restore old value in register 0x35
- movb %cl, %al
- call outidx
- popw %ax
- cmpb %ch, %al # setting lower 4 bits was successful => bad
- je no_s3 # writing is allowed => this is not an S3
-
-s3_1: movw $0x4838, %ax # allow writing to special regs by putting
- call outidx # magic number into CRT-register 0x38
- movb %cl, %al # check whether we can write special reg 0x35
- call inidx
- movb %al, %bl
- andb $0xf0, %al
- movb %al, %ah
- movb %cl, %al
- call outidx
- call inidx
- andb %ch, %al
- jnz no_s3 # no, we can't write => no S3
-
- movw %cx, %ax
- orb %bl, %ah
- call outidx
- call inidx
- andb %ch, %al
- pushw %ax
- movb %bl, %ah # restore old value in register 0x35
- movb %cl, %al
- call outidx
- popw %ax
- cmpb %ch, %al
- jne no_s31 # writing not possible => no S3
- movb $0x30, %al
- call inidx # now get the S3 id ...
- leaw idS3, %di
- movw $0x10, %cx
- repne
- scasb
- je no_s31
-
- movb %bh, %ah
- movb $0x38, %al
- jmp s3rest
-
-no_s3: movb $0x35, %al # restore CRT register 0x35
- movb %bl, %ah
- call outidx
-no_s31: xorw %bp, %bp # Detection failed
-s3rest: movb %bh, %ah
- movb $0x38, %al # restore old value of CRT register 0x38
- jmp outidx
-
-idS3: .byte 0x81, 0x82, 0x90, 0x91, 0x92, 0x93, 0x94, 0x95
- .byte 0xa0, 0xa1, 0xa2, 0xa3, 0xa4, 0xa5, 0xa8, 0xb0
-
-s3_md: .byte 0x54, 0x2b, 0x84
- .byte 0x55, 0x19, 0x84
- .byte 0
- .ascii "S3"
- .byte 0
-
-# ATI cards.
-ati_test:
- leaw idati, %si
- movw $0x31, %di
- movw $0x09, %cx
- repe
- cmpsb
- je atiok
-
- xorw %bp, %bp
-atiok: ret
-
-idati: .ascii "761295520"
-
-ati_md: .byte 0x23, 0x19, 0x84
- .byte 0x33, 0x2c, 0x84
- .byte 0x22, 0x1e, 0x64
- .byte 0x21, 0x19, 0x64
- .byte 0x58, 0x21, 0x50
- .byte 0x5b, 0x1e, 0x50
- .byte 0
- .ascii "ATI"
- .byte 0
-
-# AHEAD
-ahead_test:
- movw $0x200f, %ax
- movw $0x3ce, %dx
- outw %ax, %dx
- incw %dx
- inb %dx, %al
- cmpb $0x20, %al
- je isahed
-
- cmpb $0x21, %al
- je isahed
-
- xorw %bp, %bp
-isahed: ret
-
-ahead_md:
- .byte 0x22, 0x2c, 0x84
- .byte 0x23, 0x19, 0x84
- .byte 0x24, 0x1c, 0x84
- .byte 0x2f, 0x32, 0xa0
- .byte 0x32, 0x22, 0x50
- .byte 0x34, 0x42, 0x50
- .byte 0
- .ascii "Ahead"
- .byte 0
-
-# Chips & Tech.
-chips_test:
- movw $0x3c3, %dx
- inb %dx, %al
- orb $0x10, %al
- outb %al, %dx
- movw $0x104, %dx
- inb %dx, %al
- movb %al, %bl
- movw $0x3c3, %dx
- inb %dx, %al
- andb $0xef, %al
- outb %al, %dx
- cmpb $0xa5, %bl
- je cantok
-
- xorw %bp, %bp
-cantok: ret
-
-chips_md:
- .byte 0x60, 0x19, 0x84
- .byte 0x61, 0x32, 0x84
- .byte 0
- .ascii "Chips & Technologies"
- .byte 0
-
-# Cirrus Logic 5X0
-cirrus1_test:
- movw $0x3d4, %dx
- movb $0x0c, %al
- outb %al, %dx
- incw %dx
- inb %dx, %al
- movb %al, %bl
- xorb %al, %al
- outb %al, %dx
- decw %dx
- movb $0x1f, %al
- outb %al, %dx
- incw %dx
- inb %dx, %al
- movb %al, %bh
- xorb %ah, %ah
- shlb $4, %al
- movw %ax, %cx
- movb %bh, %al
- shrb $4, %al
- addw %ax, %cx
- shlw $8, %cx
- addw $6, %cx
- movw %cx, %ax
- movw $0x3c4, %dx
- outw %ax, %dx
- incw %dx
- inb %dx, %al
- andb %al, %al
- jnz nocirr
-
- movb %bh, %al
- outb %al, %dx
- inb %dx, %al
- cmpb $0x01, %al
- je iscirr
-
-nocirr: xorw %bp, %bp
-iscirr: movw $0x3d4, %dx
- movb %bl, %al
- xorb %ah, %ah
- shlw $8, %ax
- addw $0x0c, %ax
- outw %ax, %dx
- ret
-
-cirrus1_md:
- .byte 0x1f, 0x19, 0x84
- .byte 0x20, 0x2c, 0x84
- .byte 0x22, 0x1e, 0x84
- .byte 0x31, 0x25, 0x64
- .byte 0
- .ascii "Cirrus Logic 5X0"
- .byte 0
-
-# Cirrus Logic 54XX
-cirrus5_test:
- movw $0x3c4, %dx
- movb $6, %al
- call inidx
- movb %al, %bl # BL=backup
- movw $6, %ax
- call tstidx
- cmpb $0x0f, %al
- jne c5fail
-
- movw $0x1206, %ax
- call tstidx
- cmpb $0x12, %al
- jne c5fail
-
- movb $0x1e, %al
- call inidx
- movb %al, %bh
- movb %bh, %ah
- andb $0xc0, %ah
- movb $0x1e, %al
- call tstidx
- andb $0x3f, %al
- jne c5xx
-
- movb $0x1e, %al
- movb %bh, %ah
- orb $0x3f, %ah
- call tstidx
- xorb $0x3f, %al
- andb $0x3f, %al
-c5xx: pushf
- movb $0x1e, %al
- movb %bh, %ah
- outw %ax, %dx
- popf
- je c5done
-
-c5fail: xorw %bp, %bp
-c5done: movb $6, %al
- movb %bl, %ah
- outw %ax, %dx
- ret
-
-cirrus5_md:
- .byte 0x14, 0x19, 0x84
- .byte 0x54, 0x2b, 0x84
- .byte 0
- .ascii "Cirrus Logic 54XX"
- .byte 0
-
-# Cirrus Logic 64XX -- no known extra modes, but must be identified, because
-# it's misidentified by the Ahead test.
-cirrus6_test:
- movw $0x3ce, %dx
- movb $0x0a, %al
- call inidx
- movb %al, %bl # BL=backup
- movw $0xce0a, %ax
- call tstidx
- orb %al, %al
- jne c2fail
-
- movw $0xec0a, %ax
- call tstidx
- cmpb $0x01, %al
- jne c2fail
-
- movb $0xaa, %al
- call inidx # 4X, 5X, 7X and 8X are valid 64XX chip ID's.
- shrb $4, %al
- subb $4, %al
- jz c6done
-
- decb %al
- jz c6done
-
- subb $2, %al
- jz c6done
-
- decb %al
- jz c6done
-
-c2fail: xorw %bp, %bp
-c6done: movb $0x0a, %al
- movb %bl, %ah
- outw %ax, %dx
- ret
-
-cirrus6_md:
- .byte 0
- .ascii "Cirrus Logic 64XX"
- .byte 0
-
-# Everex / Trident
-everex_test:
- movw $0x7000, %ax
- xorw %bx, %bx
- int $0x10
- cmpb $0x70, %al
- jne noevrx
-
- shrw $4, %dx
- cmpw $0x678, %dx
- je evtrid
-
- cmpw $0x236, %dx
- jne evrxok
-
-evtrid: leaw trident_md, %bp
-evrxok: ret
-
-noevrx: xorw %bp, %bp
- ret
-
-everex_md:
- .byte 0x03, 0x22, 0x50
- .byte 0x04, 0x3c, 0x50
- .byte 0x07, 0x2b, 0x64
- .byte 0x08, 0x4b, 0x64
- .byte 0x0a, 0x19, 0x84
- .byte 0x0b, 0x2c, 0x84
- .byte 0x16, 0x1e, 0x50
- .byte 0x18, 0x1b, 0x64
- .byte 0x21, 0x40, 0xa0
- .byte 0x40, 0x1e, 0x84
- .byte 0
- .ascii "Everex/Trident"
- .byte 0
-
-# Genoa.
-genoa_test:
- leaw idgenoa, %si # Check Genoa 'clues'
- xorw %ax, %ax
- movb %es:(0x37), %al
- movw %ax, %di
- movw $0x04, %cx
- decw %si
- decw %di
-l1: incw %si
- incw %di
- movb (%si), %al
- testb %al, %al
- jz l2
-
- cmpb %es:(%di), %al
-l2: loope l1
- orw %cx, %cx
- je isgen
-
- xorw %bp, %bp
-isgen: ret
-
-idgenoa: .byte 0x77, 0x00, 0x99, 0x66
-
-genoa_md:
- .byte 0x58, 0x20, 0x50
- .byte 0x5a, 0x2a, 0x64
- .byte 0x60, 0x19, 0x84
- .byte 0x61, 0x1d, 0x84
- .byte 0x62, 0x20, 0x84
- .byte 0x63, 0x2c, 0x84
- .byte 0x64, 0x3c, 0x84
- .byte 0x6b, 0x4f, 0x64
- .byte 0x72, 0x3c, 0x50
- .byte 0x74, 0x42, 0x50
- .byte 0x78, 0x4b, 0x64
- .byte 0
- .ascii "Genoa"
- .byte 0
-
-# OAK
-oak_test:
- leaw idoakvga, %si
- movw $0x08, %di
- movw $0x08, %cx
- repe
- cmpsb
- je isoak
-
- xorw %bp, %bp
-isoak: ret
-
-idoakvga: .ascii "OAK VGA "
-
-oak_md: .byte 0x4e, 0x3c, 0x50
- .byte 0x4f, 0x3c, 0x84
- .byte 0x50, 0x19, 0x84
- .byte 0x51, 0x2b, 0x84
- .byte 0
- .ascii "OAK"
- .byte 0
-
-# WD Paradise.
-paradise_test:
- leaw idparadise, %si
- movw $0x7d, %di
- movw $0x04, %cx
- repe
- cmpsb
- je ispara
-
- xorw %bp, %bp
-ispara: ret
-
-idparadise: .ascii "VGA="
-
-paradise_md:
- .byte 0x41, 0x22, 0x50
- .byte 0x47, 0x1c, 0x84
- .byte 0x55, 0x19, 0x84
- .byte 0x54, 0x2c, 0x84
- .byte 0
- .ascii "Paradise"
- .byte 0
-
-# Trident.
-trident_test:
- movw $0x3c4, %dx
- movb $0x0e, %al
- outb %al, %dx
- incw %dx
- inb %dx, %al
- xchgb %al, %ah
- xorb %al, %al
- outb %al, %dx
- inb %dx, %al
- xchgb %ah, %al
- movb %al, %bl # Strange thing ... in the book this wasn't
- andb $0x02, %bl # necessary but it worked on my card which
- jz setb2 # is a trident. Without it the screen goes
- # blurred ...
- andb $0xfd, %al
- jmp clrb2
-
-setb2: orb $0x02, %al
-clrb2: outb %al, %dx
- andb $0x0f, %ah
- cmpb $0x02, %ah
- je istrid
-
- xorw %bp, %bp
-istrid: ret
-
-trident_md:
- .byte 0x50, 0x1e, 0x50
- .byte 0x51, 0x2b, 0x50
- .byte 0x52, 0x3c, 0x50
- .byte 0x57, 0x19, 0x84
- .byte 0x58, 0x1e, 0x84
- .byte 0x59, 0x2b, 0x84
- .byte 0x5a, 0x3c, 0x84
- .byte 0
- .ascii "Trident"
- .byte 0
-
-# Tseng.
-tseng_test:
- movw $0x3cd, %dx
- inb %dx, %al # Could things be this simple ! :-)
- movb %al, %bl
- movb $0x55, %al
- outb %al, %dx
- inb %dx, %al
- movb %al, %ah
- movb %bl, %al
- outb %al, %dx
- cmpb $0x55, %ah
- je istsen
-
-isnot: xorw %bp, %bp
-istsen: ret
-
-tseng_md:
- .byte 0x26, 0x3c, 0x50
- .byte 0x2a, 0x28, 0x64
- .byte 0x23, 0x19, 0x84
- .byte 0x24, 0x1c, 0x84
- .byte 0x22, 0x2c, 0x84
- .byte 0x21, 0x3c, 0x84
- .byte 0
- .ascii "Tseng"
- .byte 0
-
-# Video7.
-video7_test:
- movw $0x3cc, %dx
- inb %dx, %al
- movw $0x3b4, %dx
- andb $0x01, %al
- jz even7
-
- movw $0x3d4, %dx
-even7: movb $0x0c, %al
- outb %al, %dx
- incw %dx
- inb %dx, %al
- movb %al, %bl
- movb $0x55, %al
- outb %al, %dx
- inb %dx, %al
- decw %dx
- movb $0x1f, %al
- outb %al, %dx
- incw %dx
- inb %dx, %al
- movb %al, %bh
- decw %dx
- movb $0x0c, %al
- outb %al, %dx
- incw %dx
- movb %bl, %al
- outb %al, %dx
- movb $0x55, %al
- xorb $0xea, %al
- cmpb %bh, %al
- jne isnot
-
- movb $VIDEO_FIRST_V7>>8, svga_prefix # Use special mode switching
- ret
-
-video7_md:
- .byte 0x40, 0x2b, 0x50
- .byte 0x43, 0x3c, 0x50
- .byte 0x44, 0x3c, 0x64
- .byte 0x41, 0x19, 0x84
- .byte 0x42, 0x2c, 0x84
- .byte 0x45, 0x1c, 0x84
- .byte 0
- .ascii "Video 7"
- .byte 0
-
-# Realtek VGA
-realtek_test:
- leaw idrtvga, %si
- movw $0x45, %di
- movw $0x0b, %cx
- repe
- cmpsb
- je isrt
-
- xorw %bp, %bp
-isrt: ret
-
-idrtvga: .ascii "REALTEK VGA"
-
-realtek_md:
- .byte 0x1a, 0x3c, 0x50
- .byte 0x1b, 0x19, 0x84
- .byte 0x1c, 0x1e, 0x84
- .byte 0x1d, 0x2b, 0x84
- .byte 0x1e, 0x3c, 0x84
- .byte 0
- .ascii "REALTEK"
- .byte 0
-
-#endif /* CONFIG_VIDEO_SVGA */
-
-# User-defined local mode table (VGA only)
-#ifdef CONFIG_VIDEO_LOCAL
-local_modes:
- leaw local_mode_table, %si
-locm1: lodsw
- orw %ax, %ax
- jz locm2
-
- stosw
- movsw
- jmp locm1
-
-locm2: ret
-
-# This is the table of local video modes which can be supplied manually
-# by the user. Each entry consists of mode ID (word) and dimensions
-# (byte for column count and another byte for row count). These modes
-# are placed before all SVGA and VESA modes and override them if table
-# compacting is enabled. The table must end with a zero word followed
-# by NUL-terminated video adapter name.
-local_mode_table:
- .word 0x0100 # Example: 40x25
- .byte 25,40
- .word 0
- .ascii "Local"
- .byte 0
-#endif /* CONFIG_VIDEO_LOCAL */
-
-# Read a key and return the ASCII code in al, scan code in ah
-getkey: xorb %ah, %ah
- int $0x16
- ret
-
-# Read a key with a timeout of 30 seconds.
-# The hardware clock is used to get the time.
-getkt: call gettime
- addb $30, %al # Wait 30 seconds
- cmpb $60, %al
- jl lminute
-
- subb $60, %al
-lminute:
- movb %al, %cl
-again: movb $0x01, %ah
- int $0x16
- jnz getkey # key pressed, so get it
-
- call gettime
- cmpb %cl, %al
- jne again
-
- movb $0x20, %al # timeout, return `space'
- ret
-
-# Flush the keyboard buffer
-flush: movb $0x01, %ah
- int $0x16
- jz empty
-
- xorb %ah, %ah
- int $0x16
- jmp flush
-
-empty: ret
-
-# Print hexadecimal number.
-prthw: pushw %ax
- movb %ah, %al
- call prthb
- popw %ax
-prthb: pushw %ax
- shrb $4, %al
- call prthn
- popw %ax
- andb $0x0f, %al
-prthn: cmpb $0x0a, %al
- jc prth1
-
- addb $0x07, %al
-prth1: addb $0x30, %al
- jmp prtchr
-
-# Print decimal number in al
-prtdec: pushw %ax
- pushw %cx
- xorb %ah, %ah
- movb $0x0a, %cl
- idivb %cl
- cmpb $0x09, %al
- jbe lt100
-
- call prtdec
- jmp skip10
-
-lt100: addb $0x30, %al
- call prtchr
-skip10: movb %ah, %al
- addb $0x30, %al
- call prtchr
- popw %cx
- popw %ax
- ret
-
-store_edid:
-#ifdef CONFIG_FIRMWARE_EDID
- pushw %es # just save all registers
- pushw %ax
- pushw %bx
- pushw %cx
- pushw %dx
- pushw %di
-
- pushw %fs
- popw %es
-
- movl $0x13131313, %eax # memset block with 0x13
- movw $32, %cx
- movw $0x140, %di
- cld
- rep
- stosl
-
- cmpw $0x0200, vbe_version # only do EDID on >= VBE2.0
- jl no_edid
-
- pushw %es # save ES
- xorw %di, %di # Report Capability
- pushw %di
- popw %es # ES:DI must be 0:0
- movw $0x4f15, %ax
- xorw %bx, %bx
- xorw %cx, %cx
- int $0x10
- popw %es # restore ES
-
- cmpb $0x00, %ah # call successful
- jne no_edid
-
- cmpb $0x4f, %al # function supported
- jne no_edid
-
- movw $0x4f15, %ax # do VBE/DDC
- movw $0x01, %bx
- movw $0x00, %cx
- movw $0x00, %dx
- movw $0x140, %di
- int $0x10
-
-no_edid:
- popw %di # restore all registers
- popw %dx
- popw %cx
- popw %bx
- popw %ax
- popw %es
-#endif
- ret
-
-# VIDEO_SELECT-only variables
-mt_end: .word 0 # End of video mode table if built
-edit_buf: .space 6 # Line editor buffer
-card_name: .word 0 # Pointer to adapter name
-scanning: .byte 0 # Performing mode scan
-do_restore: .byte 0 # Screen contents altered during mode change
-svga_prefix: .byte VIDEO_FIRST_BIOS>>8 # Default prefix for BIOS modes
-graphic_mode: .byte 0 # Graphic mode with a linear frame buffer
-dac_size: .byte 6 # DAC bit depth
-vbe_version: .word 0 # VBE bios version
-
-# Status messages
-keymsg: .ascii "Press <RETURN> to see video modes available, "
- .ascii "<SPACE> to continue or wait 30 secs"
- .byte 0x0d, 0x0a, 0
-
-listhdr: .byte 0x0d, 0x0a
- .ascii "Mode: COLSxROWS:"
-
-crlft: .byte 0x0d, 0x0a, 0
-
-prompt: .byte 0x0d, 0x0a
- .asciz "Enter mode number or `scan': "
-
-unknt: .asciz "Unknown mode ID. Try again."
-
-badmdt: .ascii "You passed an undefined mode number."
- .byte 0x0d, 0x0a, 0
-
-vesaer: .ascii "Error: Scanning of VESA modes failed. Please "
- .ascii "report to <mj@ucw.cz>."
- .byte 0x0d, 0x0a, 0
-
-old_name: .asciz "CGA/MDA/HGA"
-
-ega_name: .asciz "EGA"
-
-svga_name: .ascii " "
-
-vga_name: .asciz "VGA"
-
-vesa_name: .asciz "VESA"
-
-name_bann: .asciz "Video adapter: "
-#endif /* CONFIG_VIDEO_SELECT */
-
-# Other variables:
-adapter: .byte 0 # Video adapter: 0=CGA/MDA/HGA,1=EGA,2=VGA
-video_segment: .word 0xb800 # Video memory segment
-force_size: .word 0 # Use this size instead of the one in BIOS vars
diff --git a/arch/i386/kernel/verify_cpu.S b/arch/i386/kernel/verify_cpu.S
deleted file mode 100644
index fff4aa6..0000000
--- a/arch/i386/kernel/verify_cpu.S
+++ /dev/null
@@ -1,94 +0,0 @@
-/* Check if CPU has some minimum CPUID bits
- This runs in 16bit mode so that the caller can still use the BIOS
- to output errors on the screen */
-#include <asm/cpufeature.h>
-#include <asm/msr.h>
-
-verify_cpu:
- pushfl # Save caller passed flags
- pushl $0 # Kill any dangerous flags
- popfl
-
-#if CONFIG_X86_MINIMUM_CPU_FAMILY >= 4
- pushfl
- pop %eax
- orl $(1<<18),%eax # try setting AC
- push %eax
- popfl
- pushfl
- popl %eax
- testl $(1<<18),%eax
- jz bad
-#endif
-#if REQUIRED_MASK0 != 0
- pushfl # standard way to check for cpuid
- popl %eax
- movl %eax,%ebx
- xorl $0x200000,%eax
- pushl %eax
- popfl
- pushfl
- popl %eax
- cmpl %eax,%ebx
- pushfl # standard way to check for cpuid
- popl %eax
- movl %eax,%ebx
- xorl $0x200000,%eax
- pushl %eax
- popfl
- pushfl
- popl %eax
- cmpl %eax,%ebx
- jz bad # REQUIRED_MASK0 != 0 requires CPUID
-
- movl $0x0,%eax # See if cpuid 1 is implemented
- cpuid
- cmpl $0x1,%eax
- jb bad # no cpuid 1
-
-#if REQUIRED_MASK0 & NEED_CMPXCHG64
- /* Some VIA C3s need magic MSRs to enable CX64. Do this here */
- cmpl $0x746e6543,%ebx # Cent
- jne 1f
- cmpl $0x48727561,%edx # aurH
- jne 1f
- cmpl $0x736c7561,%ecx # auls
- jne 1f
- movl $1,%eax # check model
- cpuid
- movl %eax,%ebx
- shr $8,%ebx
- andl $0xf,%ebx
- cmp $6,%ebx # check family == 6
- jne 1f
- shr $4,%eax
- andl $0xf,%eax
- cmpl $6,%eax # check model >= 6
- jb 1f
- # assume models >= 6 all support this MSR
- movl $MSR_VIA_FCR,%ecx
- rdmsr
- orl $((1<<1)|(1<<7)),%eax # enable CMPXCHG64 and PGE
- wrmsr
-1:
-#endif
- movl $0x1,%eax # Does the cpu have what it takes
- cpuid
-
-#if CONFIG_X86_MINIMUM_CPU_FAMILY > 4
-#error add proper model checking here
-#endif
-
- andl $REQUIRED_MASK0,%edx
- xorl $REQUIRED_MASK0,%edx
- jnz bad
-#endif /* REQUIRED_MASK0 */
-
- popfl
- xor %eax,%eax
- ret
-
-bad:
- popfl
- movl $1,%eax
- ret
diff --git a/include/linux/edd.h b/include/linux/edd.h
index b2b3e68..7b64782 100644
--- a/include/linux/edd.h
+++ b/include/linux/edd.h
@@ -49,10 +49,6 @@
#define EDD_MBR_SIG_MAX 16 /* max number of signatures to store */
#define EDD_MBR_SIG_NR_BUF 0x1ea /* addr of number of MBR signtaures at EDD_MBR_SIG_BUF
in boot_params - treat this as 1 byte */
-#define EDD_CL_EQUALS 0x3d646465 /* "edd=" */
-#define EDD_CL_OFF 0x666f /* "of" for off */
-#define EDD_CL_SKIP 0x6b73 /* "sk" for skipmbr */
-#define EDD_CL_ON 0x6e6f /* "on" for on */
#ifndef __ASSEMBLY__
--
1.5.2.2
next prev parent reply other threads:[~2007-07-11 19:34 UTC|newest]
Thread overview: 43+ messages / expand[flat|nested] mbox.gz Atom feed top
2007-07-11 19:18 x86 setup code rewrite in C - revised H. Peter Anvin
2007-07-11 19:18 ` [x86 setup 01/33] x86 setup: MAINTAINERS: formally take responsibility for the i386 boot code H. Peter Anvin
2007-07-11 19:18 ` H. Peter Anvin
2007-07-11 19:18 ` [x86 setup 02/33] hd.c: remove BIOS/CMOS queries H. Peter Anvin
2007-07-11 19:18 ` H. Peter Anvin
2007-07-11 19:18 ` [x86 setup 03/33] include/asm-i386/boot.h: This is <asm/boot.h>, not <linux/boot.h> H. Peter Anvin
2007-07-11 19:18 ` H. Peter Anvin
2007-07-11 19:18 ` [x86 setup 04/33] Unify the CPU features vectors between i386 and x86-64 H. Peter Anvin
2007-07-11 19:18 ` H. Peter Anvin
2007-07-11 19:18 ` [x86 setup 05/33] Change CONFIG_X86_MINIMUM_CPU_MODEL to CONFIG_X86_MINIMUM_CPU_FAMILY H. Peter Anvin
2007-07-11 19:18 ` H. Peter Anvin
2007-07-11 19:18 ` [x86 setup 06/33] Clean up struct screen_info (<linux/screen_info.h>) H. Peter Anvin
2007-07-11 19:18 ` H. Peter Anvin
2007-07-11 19:18 ` [x86 setup 07/33] Use a new CPU feature word to cover all Intel features that are spread around H. Peter Anvin
2007-07-11 19:18 ` H. Peter Anvin
2007-07-11 19:18 ` [x86 setup 08/33] Define zero-page offset 0x1e4 as a scratch field, and use it H. Peter Anvin
2007-07-11 19:18 ` H. Peter Anvin
2007-07-11 19:18 ` [x86 setup 09/33] Make definitions for struct e820entry and struct e820map consistent H. Peter Anvin
2007-07-11 19:18 ` H. Peter Anvin
2007-07-11 19:18 ` [x86 setup 10/33] Make struct boot_params a real structure, and remove obsolete fields H. Peter Anvin
2007-07-11 19:18 ` H. Peter Anvin
2007-07-11 19:18 ` [x86 setup 11/33] x86-64: add CONFIG_PHYSICAL_ALIGN for consistency with i386 H. Peter Anvin
2007-07-11 19:18 ` H. Peter Anvin
2007-07-11 19:18 ` [x86 setup 12/33] x86-64: add symbolic constants for the boot segment selectors H. Peter Anvin
2007-07-11 19:18 ` H. Peter Anvin
2007-07-11 19:18 ` [x86 setup 13/33] Header file to produce 16-bit code with gcc H. Peter Anvin
2007-07-11 19:18 ` H. Peter Anvin
2007-07-11 19:18 ` [x86 setup 14/33] Top header file for new x86 setup code H. Peter Anvin
2007-07-11 19:18 ` H. Peter Anvin
2007-07-11 19:18 ` [x86 setup 15/33] Simple bitops for the " H. Peter Anvin
2007-07-11 19:18 ` H. Peter Anvin
2007-07-11 19:18 ` [x86 setup 16/33] String-handling functions " H. Peter Anvin
2007-07-11 19:18 ` H. Peter Anvin
2007-07-11 19:18 ` [x86 setup 17/33] A20 handling code H. Peter Anvin
2007-07-11 19:18 ` H. Peter Anvin
2007-07-11 19:18 ` [x86 setup 18/33] APM probing code H. Peter Anvin
2007-07-11 19:18 ` H. Peter Anvin
2007-07-11 19:18 ` [x86 setup 19/33] Command-line parsing code for the new x86 setup code H. Peter Anvin
2007-07-11 19:18 ` H. Peter Anvin
2007-07-11 19:18 ` [x86 setup 20/33] Console-writing " H. Peter Anvin
2007-07-11 19:18 ` H. Peter Anvin
2007-07-11 19:18 ` [x86 setup 21/33] Version string " H. Peter Anvin
2007-07-11 19:18 ` H. Peter Anvin
2007-07-11 19:18 ` [x86 setup 22/33] CPU features verification " H. Peter Anvin
2007-07-11 19:18 ` H. Peter Anvin
2007-07-11 19:18 ` [x86 setup 23/33] EDD probing code " H. Peter Anvin
2007-07-11 19:18 ` H. Peter Anvin
2007-07-11 19:18 ` [x86 setup 24/33] MCA support for " H. Peter Anvin
2007-07-11 19:18 ` H. Peter Anvin
2007-07-11 19:18 ` [x86 setup 25/33] Memory probing support for the " H. Peter Anvin
2007-07-11 19:18 ` H. Peter Anvin
2007-07-11 19:18 ` [x86 setup 26/33] Voyager " H. Peter Anvin
2007-07-11 19:18 ` H. Peter Anvin
2007-07-11 19:18 ` [x86 setup 27/33] Video mode probing " H. Peter Anvin
2007-07-11 19:18 ` H. Peter Anvin
2007-07-16 10:59 ` Martin Mares
2007-07-11 19:18 ` [x86 setup 28/33] Code for actual protected-mode entry H. Peter Anvin
2007-07-11 19:18 ` H. Peter Anvin
2007-07-11 19:18 ` [x86 setup 29/33] Assembly header and main routine for new x86 setup code H. Peter Anvin
2007-07-11 19:18 ` H. Peter Anvin
2007-07-11 19:18 ` [x86 setup 30/33] Linker script for the " H. Peter Anvin
2007-07-11 19:18 ` H. Peter Anvin
2007-07-11 19:18 ` [x86 setup 31/33] Use the new x86 setup code for i386 H. Peter Anvin
2007-07-11 19:18 ` H. Peter Anvin
2007-07-13 9:27 ` Tilman Schmidt
2007-07-11 19:18 ` [x86 setup 32/33] Use the new x86 setup code for x86-64; unify with i386 H. Peter Anvin
2007-07-11 19:18 ` H. Peter Anvin
2007-07-11 19:18 ` H. Peter Anvin [this message]
2007-07-11 19:18 ` [x86 setup 33/33] Remove old i386 setup code H. Peter Anvin
2007-07-11 20:08 ` x86 setup code rewrite in C - revised Jeff Garzik
2007-07-11 20:29 ` H. Peter Anvin
2007-07-12 17:24 ` Linus Torvalds
2007-07-12 17:30 ` Andrew Morton
2007-07-12 17:49 ` Linus Torvalds
2007-07-12 19:38 ` Andi Kleen
-- strict thread matches above, loose matches on Subject: below --
2007-07-10 2:51 x86 setup code rewrite in C H. Peter Anvin
2007-07-10 2:51 ` [x86 setup 01/33] x86 setup: MAINTAINERS: formally take responsibility for the i386 boot code H. Peter Anvin
2007-07-10 2:51 ` [x86 setup 02/33] hd.c: remove BIOS/CMOS queries H. Peter Anvin
2007-07-10 2:51 ` [x86 setup 03/33] include/asm-i386/boot.h: This is <asm/boot.h>, not <linux/boot.h> H. Peter Anvin
2007-07-10 2:51 ` [x86 setup 04/33] Unify the CPU features vectors between i386 and x86-64 H. Peter Anvin
2007-07-10 2:51 ` [x86 setup 05/33] Change CONFIG_X86_MINIMUM_CPU_MODEL to CONFIG_X86_MINIMUM_CPU_FAMILY H. Peter Anvin
2007-07-10 2:51 ` [x86 setup 06/33] Clean up struct screen_info (<linux/screen_info.h>) H. Peter Anvin
2007-07-10 2:51 ` [x86 setup 07/33] Use a new CPU feature word to cover all Intel features that are spread around H. Peter Anvin
2007-07-10 2:51 ` [x86 setup 08/33] Define zero-page offset 0x1e4 as a scratch field, and use it H. Peter Anvin
2007-07-10 2:51 ` [x86 setup 09/33] Make definitions for struct e820entry and struct e820map consistent H. Peter Anvin
2007-07-10 2:51 ` [x86 setup 10/33] Make struct boot_params a real structure, and remove obsolete fields H. Peter Anvin
2007-07-10 2:51 ` [x86 setup 11/33] x86-64: add CONFIG_PHYSICAL_ALIGN for consistency with i386 H. Peter Anvin
2007-07-10 2:51 ` [x86 setup 12/33] x86-64: add symbolic constants for the boot segment selectors H. Peter Anvin
2007-07-10 2:51 ` [x86 setup 13/33] Header file to produce 16-bit code with gcc H. Peter Anvin
2007-07-10 2:51 ` [x86 setup 14/33] Top header file for new x86 setup code H. Peter Anvin
2007-07-10 2:51 ` [x86 setup 15/33] Simple bitops for the " H. Peter Anvin
2007-07-10 2:51 ` [x86 setup 16/33] String-handling functions " H. Peter Anvin
2007-07-10 2:51 ` [x86 setup 17/33] A20 handling code H. Peter Anvin
2007-07-10 2:51 ` [x86 setup 18/33] APM probing code H. Peter Anvin
2007-07-10 2:51 ` [x86 setup 19/33] Command-line parsing code for the new x86 setup code H. Peter Anvin
2007-07-10 2:51 ` [x86 setup 20/33] Console-writing " H. Peter Anvin
2007-07-10 2:52 ` [x86 setup 21/33] Version string " H. Peter Anvin
2007-07-10 2:52 ` [x86 setup 22/33] CPU features verification " H. Peter Anvin
2007-07-10 2:52 ` [x86 setup 23/33] EDD probing code " H. Peter Anvin
2007-07-10 2:52 ` [x86 setup 24/33] MCA support for " H. Peter Anvin
2007-07-10 2:52 ` [x86 setup 25/33] Memory probing support for the " H. Peter Anvin
2007-07-10 2:52 ` [x86 setup 26/33] Voyager " H. Peter Anvin
2007-07-10 2:52 ` [x86 setup 27/33] Video mode probing " H. Peter Anvin
2007-07-10 2:52 ` [x86 setup 28/33] Code for actual protected-mode entry H. Peter Anvin
2007-07-10 2:52 ` [x86 setup 29/33] Assembly header and main routine for new x86 setup code H. Peter Anvin
2007-07-10 2:52 ` [x86 setup 30/33] Linker script for the " H. Peter Anvin
2007-07-10 2:52 ` [x86 setup 31/33] Use the new x86 setup code for i386 H. Peter Anvin
2007-07-10 2:52 ` [x86 setup 32/33] Use the new x86 setup code for x86-64; unify with i386 H. Peter Anvin
2007-07-10 2:51 ` [x86 setup 01/33] x86 setup: MAINTAINERS: formally take responsibility for the i386 boot code H. Peter Anvin
2007-07-10 2:52 ` [x86 setup 33/33] Remove old i386 setup code H. Peter Anvin
2007-07-10 2:52 ` H. Peter Anvin
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=11841815441652-git-send-email-hpa@zytor.com \
--to=hpa@zytor.com \
--cc=andi@firstfloor.org \
--cc=linux-kernel@vger.kernel.org \
--cc=torvalds@linux-foundation.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.