BIG PROBLEM

BIG PROBLEM

[james bond]

1-systeme hangs when i try ton compile anything

i've  compiled the kernel 2.4.4 , once i finish and boot the first time on 
2.4.4 everything goses ok ,
only too problemes
1st-  klogd takes 100%  CPU time
2nd- cat /proc/cpuinf --guives me too CPU'S  without putin any info about 
the CPU 1
like that  approximatively

--------------------------------------------

processor : 0
vendor_id : GenuineIntel
cpu family : 6
model : 7
model name : Pentium III (Katmai)
stepping : 3
cpu MHz : 498.672
cache size : 512 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat 
pse36 mmx fxsr sse
bogomips : 992.87

processor : 1
vendor_id : GenuineIntel
cpu family : 6
model : 7
model name :
stepping : 3
cpu MHz :
cache size :
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 3
wp : yes
flags           :
bogomips  :
--------------------------------------------


at the second boot it detects correctly CPU0 and CPU1



cat /proc/cpuinfo -->
-------------------------------------------
processor       : 0
vendor_id       : GenuineIntel
cpu family      : 6
model           : 7
model name      : Pentium III (Katmai)
stepping        : 3
cpu MHz         : 498.672
cache size      : 512 KB
fdiv_bug        : no
hlt_bug         : no
f00f_bug        : no
coma_bug        : no
fpu             : yes
fpu_exception   : yes
cpuid level     : 2
wp              : yes
flags           : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca 
cmov
pat pse36 mmx fxsr sse
bogomips        : 992.87

processor       : 1
vendor_id       : GenuineIntel
cpu family      : 6
model           : 7
model name      : Pentium III (Katmai)
stepping        : 3
cpu MHz         : 498.672
cache size      : 512 KB
fdiv_bug        : no
hlt_bug         : no
f00f_bug        : no
coma_bug        : no
fpu             : yes
fpu_exception   : yes
cpuid level     : 3
wp              : yes
flags           : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca 
cmov
pat pse36 mmx fxsr sse
bogomips        : 996.14
----------------------------------------
cat /proc/version -->
----------------------------------------
Linux version 2.4.4 (root@seraka) (gcc version 2.95.3 20010315 (release)) #2 
SMP Thu Jun 28 07:04:06 CEST 2001
----------------------------------------
cat /proc/modules --> nothing   cause im no using modules
----------------------------------------
cat /proc/ioports
-------------------------------0000-001f : dma1
0020-003f : pic1
0040-005f : timer
0060-006f : keyboard
0080-008f : dma page reg
00a0-00bf : pic2
00c0-00df : dma2
00f0-00ff : fpu
02f8-02ff : serial(auto)
03c0-03df : vga+
03f8-03ff : serial(auto)
0cf8-0cff : PCI conf1
4000-403f : Intel Corporation 82371AB PIIX4 ACPI
5000-501f : Intel Corporation 82371AB PIIX4 ACPI
d000-dfff : PCI Bus #01
e000-e01f : Intel Corporation 82371AB PIIX4 USB
e400-e4ff : Adaptec 7892A00000000-0009fbff : System RAM
0009fc00-0009ffff : reserved
000a0000-000bffff : Video RAM area
000c0000-000c7fff : Video ROM
000cc000-000d25ff : Extension ROM
000d3000-000d87ff : Extension ROM
000f0000-000fffff : System ROM
00100000-0ffeffff : System RAM
  00100000-00245892 : Kernel code
  00245893-002ca41f : Kernel data
0fff0000-0fff2fff : ACPI Non-volatile Storage
0fff3000-0fffffff : ACPI Tables
d8000000-dbffffff : Intel Corporation 440BX/ZX - 82443BX/ZX Host bridge
dc000000-dfffffff : PCI Bus #01
  dc000000-dc003fff : Matrox Graphics, Inc. MGA G400 AGP
  dd000000-dd7fffff : Matrox Graphics, Inc. MGA G400 AGP
e0000000-e1ffffff : PCI Bus #01
  e0000000-e1ffffff : Matrox Graphics, Inc. MGA G400 AGP
e5000000-e5007fff : Yamaha Corporation YMF-724
e5008000-e5008fff : Adaptec AHA-2940U2/W
  e5008000-e5008fff : aic7xxx
e5009000-e5009fff : Adaptec 7892A
  e5009000-e5009fff : aic7xxx
fec00000-fec00fff : reserved
fee00000-fee00fff : reserved
ffff0000-ffffffff : reserved
------------------------------------------------
e800-e8ff : Adaptec AHA-2940U2/W
ec00-ec1f : 3Com Corporation 3c595 100BaseTX [Vortex]
ec00-ec1f : eth0
f000-f00f : Intel Corporation 82371AB PIIX4 IDE
-----------------------
cat /proc/iomem  --->00000000-0009fbff : System RAM
0009fc00-0009ffff : reserved
000a0000-000bffff : Video RAM area
000c0000-000c7fff : Video ROM
000cc000-000d25ff : Extension ROM
000d3000-000d87ff : Extension ROM
000f0000-000fffff : System ROM
00100000-0ffeffff : System RAM
  00100000-00245892 : Kernel code
  00245893-002ca41f : Kernel data
0fff0000-0fff2fff : ACPI Non-volatile Storage
0fff3000-0fffffff : ACPI Tables
d8000000-dbffffff : Intel Corporation 440BX/ZX - 82443BX/ZX Host bridge
dc000000-dfffffff : PCI Bus #01
  dc000000-dc003fff : Matrox Graphics, Inc. MGA G400 AGP
  dd000000-dd7fffff : Matrox Graphics, Inc. MGA G400 AGP
e0000000-e1ffffff : PCI Bus #01
  e0000000-e1ffffff : Matrox Graphics, Inc. MGA G400 AGP
e5000000-e5007fff : Yamaha Corporation YMF-724
e5008000-e5008fff : Adaptec AHA-2940U2/W
  e5008000-e5008fff : aic7xxx
e5009000-e5009fff : Adaptec 7892A
  e5009000-e5009fff : aic7xxx
fec00000-fec00fff : reserved
fee00000-fee00fff : reserved
ffff0000-ffffffff : reserved
----------------------------------------------
lspci -vvv  --->



Expansion ROM at e2000000 [disabled] [size=128K]
       Capabilities: [dc] Power Management version 2
               Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA 
PME(D0-,D1-,D2-,D3hot-,D3cold-)
               Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:09.0 SCSI storage controller: Adaptec AHA-2940U2/W
       Subsystem: Adaptec: Unknown device a180
       Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B-
       Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
       Latency: 64 (9750ns min, 6250ns max), cache line size 08
       Interrupt: pin A routed to IRQ 17
       BIST result: 00
       Region 0: I/O ports at e800 [disabled] [size=256]
       Region 1: Memory at e5008000 (64-bit, non-prefetchable) [size=4K]
       Expansion ROM at e3000000 [disabled] [size=128K]
       Capabilities: [dc] Power Management version 1
               Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA 
PME(D0-,D1-,D2-,D3hot-,D3cold-)
               Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:0a.0 Ethernet controller: 3Com Corporation 3c595 100BaseTX [Vortex]
       Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B-
       Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
       Latency: 248 (750ns min, 2000ns max)
       Interrupt: pin A routed to IRQ 18
       Region 0: I/O ports at ec00 [size=32]
       Expansion ROM at e4000000 [disabled] [size=64K]

00:0c.0 Multimedia audio controller: Yamaha Corporation YMF-724 (rev 05)
       Subsystem: Yamaha Corporation YMF724-Based PCI Audio Adapter
       Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B-
       Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
       Latency: 64 (1250ns min, 6250ns max)
       Interrupt: pin A routed to IRQ 16
       Region 0: Memory at e5000000 (32-bit, non-prefetchable) [size=32K]
       Capabilities: [50] Power Management version 1
               Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA 
PME(D0-,D1-,D2-,D3hot-,D3cold-)
               Status: D0 PME-Enable- DSel=0 DScale=0 PME-

01:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G400 AGP (rev 
82) (prog-if 00 [VGA])
       Subsystem: Matrox Graphics, Inc.: Unknown device 0641
       Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B-
       Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
       Latency: 64 (4000ns min, 8000ns max), cache line size 08
       Interrupt: pin A routed to IRQ 0
       Region 0: Memory at e0000000 (32-bit, prefetchable) [size=32M]
       Region 1: Memory at dc000000 (32-bit, non-prefetchable) [size=16K]
       Region 2: Memory at dd000000 (32-bit, non-prefetchable) [size=8M]
       Expansion ROM at <unassigned> [disabled] [size=128K]
       Capabilities: [dc] Power Management version 2
               Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA 
PME(D0-,D1-,D2-,D3hot-,D3cold-)
               Status: D0 PME-Enable- DSel=0 DScale=0 PME-
       Capabilities: [f0] AGP version 2.0
               Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
               Command: RQ=31 SBA+ AGP+ 64bit- FW- Rate=x1
-----------------------------------------------------

cat /proc/scsi/scsi -->
-----------------------------------------------------
Host: scsi0 Channel: 00 Id: 00 Lun: 00
  Vendor: IBM      Model: DDYS-T18350M     Rev: S93D
  Type:   Direct-Access                    ANSI SCSI revision: 03
Host: scsi1 Channel: 00 Id: 01 Lun: 00
  Vendor: COMPAQ   Model: HB00931B93       Rev: A195
  Type:   Direct-Access                    ANSI SCSI revision: 02
Host: scsi1 Channel: 00 Id: 02 Lun: 00
  Vendor: PLEXTOR  Model: CD-ROM PX-32TS   Rev: 1.03
  Type:   CD-ROM                           ANSI SCSI revision: 02
Host: scsi1 Channel: 00 Id: 03 Lun: 00
  Vendor: PLEXTOR  Model: CD-R   PX-R820T  Rev: 1.06
  Type:   CD-ROM                           ANSI SCSI revision: 02
Host: scsi1 Channel: 00 Id: 04 Lun: 00
  Vendor: COMPAQ   Model: HB00931B93       Rev: A195
  Type:   Direct-Access                    ANSI SCSI revision: 02
----------------------------------------------------

my motherboard is an Gigabyte GA-6BXD with f3 bios and my memory is 256  ECC 
,
so perhaps the defucnt is caused by the second CPU "CPU1" cause i hade somme 
probles with is ,


thank's for helping me caus i start to disespaire "sorry for my poor 
english"
and i don't wana use Miscosoft

with regards

---------------------------------------------------
please answer me @ battata.chafik@noos.fr thanks

_________________________________________________________________________
Get Your Private, Free E-mail from MSN Hotmail at http://www.hotmail.com.

Re: BIG PROBLEM

[Alan Cox]

> i've  compiled the kernel 2.4.4 , once i finish and boot the first time on 
> 2.4.4 everything goses ok ,
> only too problemes
> 1st-  klogd takes 100%  CPU time

Old old versions of klogd had bugs where they would do that. If there is
a continuous problem it may also do so - does 'dmesg' show anything ?

> 2nd- cat /proc/cpuinf --guives me too CPU'S  without putin any info about 
> the CPU 1

Im not sure I follow the description - can you explain more.

Re: BIG PROBLEM

[Ryan W. Maple]

On Thu, 28 Jun 2001, Alan Cox wrote:

> > i've  compiled the kernel 2.4.4 , once i finish and boot the first time on 
> > 2.4.4 everything goses ok ,
> > only too problemes
> > 1st-  klogd takes 100%  CPU time
> 
> Old old versions of klogd had bugs where they would do that. If there is
> a continuous problem it may also do so - does 'dmesg' show anything ?

I don't think it's limited to "old old" versions.  Version 1.3 would hit
100% CPU (DoS-style) when it received NULL bytes IIRC.

  http://lists.jammed.com/owl-users/2001/05/0000.html

>From what I remember, this happened with some of the 3com ethernet drivers
(the NULL bytes).  Maybe this is his problem wrt klogd...

Ryan

 +-- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --+
   Ryan W. Maple          "I dunno, I dream in Perl sometimes..."  -LW
   Guardian Digital, Inc.                     ryan@guardiandigital.com
 +-- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --+

Re: BIG PROBLEM

[Ralf Baechle]

On Thu, Jun 28, 2001 at 06:49:46PM -0000, james bond wrote:

> 1-systeme hangs when i try ton compile anything
> 
> i've  compiled the kernel 2.4.4 , once i finish and boot the first time on 
> 2.4.4 everything goses ok ,
> only too problemes
> 1st-  klogd takes 100%  CPU time

Some versions of the 3c59x driver emit a NUL character on bootup which makes
klogd suck CPU.  This is fixed in 2.4.5, dunno about 2.4.4.

  Ralf

Re: BIG PROBLEM

[Justin Guyett]

On Thu, 28 Jun 2001, Ralf Baechle wrote:

> Some versions of the 3c59x driver emit a NUL character on bootup which makes
> klogd suck CPU.  This is fixed in 2.4.5, dunno about 2.4.4.

sysklogd 1.4.1 changelog lists a no busyloop fix.


justin

Re: BIG PROBLEM

[Ryan W. Maple]

On Thu, 28 Jun 2001, Justin Guyett wrote:

> On Thu, 28 Jun 2001, Ralf Baechle wrote:
> 
> > Some versions of the 3c59x driver emit a NUL character on bootup which makes
> > klogd suck CPU.  This is fixed in 2.4.5, dunno about 2.4.4.
> 
> sysklogd 1.4.1 changelog lists a no busyloop fix.

Check out:  http://bugs.debian.org/85478

  "When klogd's LogLine() function encounters a null byte in state
   PARSING_TEXT, it will loop infinitely.  More precisely, copyin()
   will treat the null byte as a delimiter - unlike LogLine(), which
   will invoke copyin() ever and ever again."

Kinda off-topic, but I just wanted to prove that the bug was in klogd and
not the kernel. :)

-r

Re: BIG PROBLEM

[Ralf Baechle]

On Thu, Jun 28, 2001 at 05:35:14PM -0400, Ryan W. Maple wrote:

> Check out:  http://bugs.debian.org/85478
> 
>   "When klogd's LogLine() function encounters a null byte in state
>    PARSING_TEXT, it will loop infinitely.  More precisely, copyin()
>    will treat the null byte as a delimiter - unlike LogLine(), which
>    will invoke copyin() ever and ever again."
> 
> Kinda off-topic, but I just wanted to prove that the bug was in klogd and
> not the kernel. :)

The kernel definately shouldn't communicate with the user using NUL chars.

  Ralf

Big Problem

[ohviey1]

When i try to cross compile with an elf toolchain i have this error:

arm-elf-ld: no machine record defined

Sameone could help me?

Re: Big Problem

[Richard Purdie]

On Thu, 2008-01-31 at 15:19 +0100, ohviey1 wrote:
> When i try to cross compile with an elf toolchain i have this error:
> 
> arm-elf-ld: no machine record defined
> 
> Sameone could help me?

Based on that information, almost certainly not. There is no description
of what you're actually doing, the single error message line is near
enough useless.

Assuming there are not two people with this problem, you've already been
told the problem is due to incorrect setup in your kernel defconfig (no
machines are enabled).

Regards,

Richard