From: Vasanthakumar Thiagarajan <vasanth@atheros.com>
To: <linville@tuxdriver.com>
Cc: <linux-wireless@vger.kernel.org>
Subject: [PATCH 00/26] Add support for AR9485
Date: Tue, 30 Nov 2010 23:32:29 -0800 [thread overview]
Message-ID: <1291188775-13707-1-git-send-email-vasanth@atheros.com> (raw)
John,
This patch series add support for a new chipset of AR9003 family.
This chip(AR9485) is an 1x1 and 2.4Ghz band only.
Vasanth
Vasanthakumar Thiagarajan (26):
ath9k_hw: Define hw version macros for AR9485
ath9k_hw: Add initvals.h for AR9485
ath9k_hw: Enable hw initialization for AR9485
ath9k_hw: Initialize mode registers for AR9485
ath9k_hw: Initialize tx/rx gain table from initvals.h for AR9485
ath9k_hw: Eeeprom changes for AR9485
ath9k_hw: Disable LDPC for AR9485
ath9k: Disable TX STBC for AR9485
ath9k: Enable extended synch for AR9485 to fix L0s recovery issue
ath9k: Configure pll control for AR9485
ath9k_hw: Find chansel of AR_PHY_65NM_CH0_SYNTH7 from an array for
AR9485
ath9k_hw: Add a helper function to get spur channel pointer from cal
data for AR9003 family
ath9k: Read spur channel information from eeprom for AR9485
ath9k_hw: Configure xpa bias level for AR9485
ath9k_hw: Read and configure antenna diversity control for AR9485
ath9k_hw: Configure attenuation control only for chain 0 on AR9485
ath9k_hw: Configure internal regulator for AR9485
ath9k_hw: Read and configure turnning caps to regulate freq accuracy
ath9k_hw: Configure power control only for chain 0 on AR9485
ath9k_hw: Program appropriate chianmask for AR9485 before starting
AGC/IQ cal
ath9k_hw: Define IQcal correction coefficient registers using index
ath9k_hw: Add IQ cal changes for AR9485
ath9k_hw: Program appropriate register for temperature compensation
cal for AR9485
ath9k_hw: Setup paprd only for chain 0 on AR9485
ath9k_hw: Disable MRC CCK for AR9485
ath9k: Add device id of AR9485 to pci table
drivers/net/wireless/ath/ath.h | 1 +
drivers/net/wireless/ath/ath9k/ani.c | 2 +-
drivers/net/wireless/ath/ath9k/ar9003_calib.c | 256 ++++++-
drivers/net/wireless/ath/ath9k/ar9003_eeprom.c | 193 ++++-
drivers/net/wireless/ath/ath9k/ar9003_eeprom.h | 2 +
drivers/net/wireless/ath/ath9k/ar9003_hw.c | 278 +++++--
drivers/net/wireless/ath/ath9k/ar9003_paprd.c | 40 +-
drivers/net/wireless/ath/ath9k/ar9003_phy.c | 76 ++-
drivers/net/wireless/ath/ath9k/ar9003_phy.h | 70 ++-
drivers/net/wireless/ath/ath9k/ar9485_initvals.h | 943 ++++++++++++++++++++++
drivers/net/wireless/ath/ath9k/hw.c | 19 +-
drivers/net/wireless/ath/ath9k/hw.h | 3 +
drivers/net/wireless/ath/ath9k/init.c | 4 +-
drivers/net/wireless/ath/ath9k/main.c | 3 +
drivers/net/wireless/ath/ath9k/pci.c | 13 +
drivers/net/wireless/ath/ath9k/reg.h | 10 +
16 files changed, 1745 insertions(+), 168 deletions(-)
create mode 100644 drivers/net/wireless/ath/ath9k/ar9485_initvals.h
next reply other threads:[~2010-12-01 7:32 UTC|newest]
Thread overview: 38+ messages / expand[flat|nested] mbox.gz Atom feed top
2010-12-01 7:32 Vasanthakumar Thiagarajan [this message]
2010-12-01 7:32 ` [PATCH 01/26] ath9k_hw: Define hw version macros for AR9485 Vasanthakumar Thiagarajan
2010-12-01 7:32 ` [PATCH 02/26] ath9k_hw: Add initvals.h " Vasanthakumar Thiagarajan
2010-12-01 7:32 ` [PATCH 03/26] ath9k_hw: Enable hw initialization " Vasanthakumar Thiagarajan
2010-12-01 7:32 ` [PATCH 04/26] ath9k_hw: Initialize mode registers " Vasanthakumar Thiagarajan
2010-12-01 7:32 ` [PATCH 05/26] ath9k_hw: Initialize tx/rx gain table from initvals.h " Vasanthakumar Thiagarajan
2010-12-01 7:32 ` [PATCH 06/26] ath9k_hw: Eeeprom changes " Vasanthakumar Thiagarajan
2010-12-01 7:32 ` [PATCH 07/26] ath9k_hw: Disable LDPC " Vasanthakumar Thiagarajan
2010-12-01 7:32 ` [PATCH 08/26] ath9k: Disable TX STBC " Vasanthakumar Thiagarajan
2010-12-01 7:32 ` [PATCH 09/26] ath9k: Enable extended synch for AR9485 to fix L0s recovery issue Vasanthakumar Thiagarajan
2010-12-01 7:32 ` [PATCH 10/26] ath9k: Configure pll control for AR9485 Vasanthakumar Thiagarajan
2010-12-01 16:39 ` Felix Fietkau
2010-12-02 5:05 ` Vasanthakumar Thiagarajan
2010-12-02 5:09 ` Vasanthakumar Thiagarajan
2010-12-01 7:32 ` [PATCH 11/26] ath9k_hw: Find chansel of AR_PHY_65NM_CH0_SYNTH7 from an array " Vasanthakumar Thiagarajan
2010-12-01 16:45 ` Felix Fietkau
2010-12-02 5:43 ` Vasanthakumar Thiagarajan
2010-12-01 7:32 ` [PATCH 12/26] ath9k_hw: Add a helper function to get spur channel pointer from cal data for AR9003 family Vasanthakumar Thiagarajan
2010-12-01 7:32 ` [PATCH 13/26] ath9k: Read spur channel information from eeprom for AR9485 Vasanthakumar Thiagarajan
2010-12-01 7:32 ` [PATCH 14/26] ath9k_hw: Configure xpa bias level " Vasanthakumar Thiagarajan
2010-12-01 7:32 ` [PATCH 15/26] ath9k_hw: Read and configure antenna diversity control " Vasanthakumar Thiagarajan
2010-12-01 7:32 ` [PATCH 16/26] ath9k_hw: Configure attenuation control only for chain 0 on AR9485 Vasanthakumar Thiagarajan
2010-12-01 16:50 ` Felix Fietkau
2010-12-02 5:13 ` Vasanthakumar Thiagarajan
2010-12-01 7:32 ` [PATCH 17/26] ath9k_hw: Configure internal regulator for AR9485 Vasanthakumar Thiagarajan
2010-12-01 7:32 ` [PATCH 18/26] ath9k_hw: Read and configure turnning caps to regulate freq accuracy Vasanthakumar Thiagarajan
2010-12-01 7:32 ` [PATCH 19/26] ath9k_hw: Configure power control only for chain 0 on AR9485 Vasanthakumar Thiagarajan
2010-12-01 16:51 ` Felix Fietkau
2010-12-01 7:32 ` [PATCH 20/26] ath9k_hw: Program appropriate chianmask for AR9485 before starting AGC/IQ cal Vasanthakumar Thiagarajan
2010-12-01 7:32 ` [PATCH 21/26] ath9k_hw: Define IQcal correction coefficient registers using index Vasanthakumar Thiagarajan
2010-12-01 7:32 ` [PATCH 22/26] ath9k_hw: Add IQ cal changes for AR9485 Vasanthakumar Thiagarajan
2010-12-01 7:32 ` [PATCH 23/26] ath9k_hw: Program appropriate register for temperature compensation cal " Vasanthakumar Thiagarajan
2010-12-01 7:32 ` [PATCH 24/26] ath9k_hw: Setup paprd only for chain 0 on AR9485 Vasanthakumar Thiagarajan
2010-12-01 16:52 ` Felix Fietkau
2010-12-01 7:32 ` [PATCH 25/26] ath9k_hw: Disable MRC CCK for AR9485 Vasanthakumar Thiagarajan
2010-12-01 7:32 ` [PATCH 26/26] ath9k: Add device id of AR9485 to pci table Vasanthakumar Thiagarajan
2010-12-01 7:52 ` [PATCH 00/26] Add support for AR9485 Luis R. Rodriguez
2010-12-01 8:36 ` Vasanthakumar Thiagarajan
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1291188775-13707-1-git-send-email-vasanth@atheros.com \
--to=vasanth@atheros.com \
--cc=linux-wireless@vger.kernel.org \
--cc=linville@tuxdriver.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.