From: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
To: broonie@kernel.org
Cc: alsa-devel@alsa-project.org, info@crazy-audio.com,
florian.meier@koalo.de, lgirdwood@gmail.com,
patches@opensource.wolfsonmicro.com
Subject: [PATCH] ASoC: wm8804: Allow control of master clock divider in PLL generation
Date: Thu, 29 May 2014 15:08:03 +0100 [thread overview]
Message-ID: <1401372483-10216-1-git-send-email-ckeepax@opensource.wolfsonmicro.com> (raw)
From: Daniel Matuschek <info@crazy-audio.com>
WM8804 can run with PLL frequencies of 256xfs and 128xfs for
most sample rates. At 192kHz only 128xfs is supported. The
existing driver selects 128xfs automatically for some lower
samples rates. By using an additional mclk_div divider, it
is now possible to control the behaviour. This allows using
256xfs PLL frequency on all sample rates up to 96kHz. It
should allow lower jitter and better signal quality. The
behavior has to be controlled by the sound card driver,
because some sample frequency share the same setting. e.g.
192kHz and 96kHz use 24.576MHz master clock. The only
difference is the MCLK divider.
Signed-off-by: Daniel Matuschek <daniel@matuschek.net>
Tested-by: Florian Meier <florian.meier@koalo.de>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
---
Hi,
Looks like the version of this patch that was sent in didn't
apply on the ASoC tree which is probably why it seems to
have been missed. Not sure whether this was an email client
fail or the patch was generated against the wrong tree but
as it is a useful patch I have taken the liberty of fixing
it up (code is exactly the same) and resending.
Thanks,
Charles
sound/soc/codecs/wm8804.c | 17 ++++++++++++++---
sound/soc/codecs/wm8804.h | 4 ++++
2 files changed, 18 insertions(+), 3 deletions(-)
diff --git a/sound/soc/codecs/wm8804.c b/sound/soc/codecs/wm8804.c
index bbcad9f..d96e596 100644
--- a/sound/soc/codecs/wm8804.c
+++ b/sound/soc/codecs/wm8804.c
@@ -63,6 +63,7 @@ struct wm8804_priv {
struct regmap *regmap;
struct regulator_bulk_data supplies[WM8804_NUM_SUPPLIES];
struct notifier_block disable_nb[WM8804_NUM_SUPPLIES];
+ int mclk_div;
};
static int txsrc_get(struct snd_kcontrol *kcontrol,
@@ -318,7 +319,7 @@ static struct {
#define FIXED_PLL_SIZE ((1ULL << 22) * 10)
static int pll_factors(struct pll_div *pll_div, unsigned int target,
- unsigned int source)
+ unsigned int source, unsigned int mclk_div)
{
u64 Kpart;
unsigned long int K, Ndiv, Nmod, tmp;
@@ -330,7 +331,8 @@ static int pll_factors(struct pll_div *pll_div, unsigned int target,
*/
for (i = 0; i < ARRAY_SIZE(post_table); i++) {
tmp = target * post_table[i].div;
- if (tmp >= 90000000 && tmp <= 100000000) {
+ if ((tmp >= 90000000 && tmp <= 100000000) &&
+ (mclk_div == post_table[i].mclkdiv)) {
pll_div->freqmode = post_table[i].freqmode;
pll_div->mclkdiv = post_table[i].mclkdiv;
target *= post_table[i].div;
@@ -387,8 +389,12 @@ static int wm8804_set_pll(struct snd_soc_dai *dai, int pll_id,
} else {
int ret;
struct pll_div pll_div;
+ struct wm8804_priv *wm8804;
- ret = pll_factors(&pll_div, freq_out, freq_in);
+ wm8804 = snd_soc_codec_get_drvdata(codec);
+
+ ret = pll_factors(&pll_div, freq_out, freq_in,
+ wm8804->mclk_div);
if (ret)
return ret;
@@ -452,6 +458,7 @@ static int wm8804_set_clkdiv(struct snd_soc_dai *dai,
int div_id, int div)
{
struct snd_soc_codec *codec;
+ struct wm8804_priv *wm8804;
codec = dai->codec;
switch (div_id) {
@@ -459,6 +466,10 @@ static int wm8804_set_clkdiv(struct snd_soc_dai *dai,
snd_soc_update_bits(codec, WM8804_PLL5, 0x30,
(div & 0x3) << 4);
break;
+ case WM8804_MCLK_DIV:
+ wm8804 = snd_soc_codec_get_drvdata(codec);
+ wm8804->mclk_div = div;
+ break;
default:
dev_err(dai->dev, "Unknown clock divider: %d\n", div_id);
return -EINVAL;
diff --git a/sound/soc/codecs/wm8804.h b/sound/soc/codecs/wm8804.h
index 8ec14f5..e72d4f4 100644
--- a/sound/soc/codecs/wm8804.h
+++ b/sound/soc/codecs/wm8804.h
@@ -57,5 +57,9 @@
#define WM8804_CLKOUT_SRC_OSCCLK 4
#define WM8804_CLKOUT_DIV 1
+#define WM8804_MCLK_DIV 2
+
+#define WM8804_MCLKDIV_256FS 0
+#define WM8804_MCLKDIV_128FS 1
#endif /* _WM8804_H */
--
1.7.2.5
next reply other threads:[~2014-05-29 14:15 UTC|newest]
Thread overview: 17+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-05-29 14:08 Charles Keepax [this message]
2014-05-29 15:01 ` [PATCH] ASoC: wm8804: Allow control of master clock divider in PLL generation Mark Brown
-- strict thread matches above, loose matches on Subject: below --
2014-01-14 19:34 Daniel Matuschek
2014-01-17 0:54 ` Mark Brown
2014-01-17 0:54 ` Mark Brown
2014-01-17 10:35 ` Dimitris Papastamos
2014-01-17 9:48 ` Charles Keepax
2014-01-17 12:22 ` Mark Brown
2014-01-17 12:22 ` Mark Brown
2014-01-17 16:43 ` Florian Meier
2014-01-17 17:59 ` Mark Brown
2014-01-17 18:26 ` Daniel Matuschek
[not found] ` <52D97120.8030606@koalo.de>
[not found] ` <20140117183332.GC17314@sirena.org.uk>
2014-01-17 18:44 ` Florian Meier
2014-01-17 18:47 ` Mark Brown
2014-01-12 21:11 Daniel Matuschek
2014-01-13 9:21 ` Florian Meier
2014-01-13 11:14 ` Charles Keepax
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1401372483-10216-1-git-send-email-ckeepax@opensource.wolfsonmicro.com \
--to=ckeepax@opensource.wolfsonmicro.com \
--cc=alsa-devel@alsa-project.org \
--cc=broonie@kernel.org \
--cc=florian.meier@koalo.de \
--cc=info@crazy-audio.com \
--cc=lgirdwood@gmail.com \
--cc=patches@opensource.wolfsonmicro.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.