From: Heiko Schocher <hs@denx.de>
To: u-boot@lists.denx.de
Subject: [U-Boot] [v2 PATCH 11/12] arm, at91, spl: add spl support for the taurus board
Date: Thu, 30 Oct 2014 09:15:05 +0100 [thread overview]
Message-ID: <1414656906-16632-12-git-send-email-hs@denx.de> (raw)
In-Reply-To: <1414656906-16632-1-git-send-email-hs@denx.de>
replaces the at91bootstrap code with SPL code.
make the spl image with:
./tools/mkimage -T atmelimage -d spl/u-boot-spl.bin spl/boot.bin
this writes the length of the spl image into the 6th
execption vector. This is needed from the ROM bootloader.
Signed-off-by: Heiko Schocher <hs@denx.de>
---
Changes in v2:
- rename function "nand_erase_one" to "spl_nand_erase_one" as
Scott Wood suggested
arch/arm/Kconfig | 1 +
board/siemens/taurus/taurus.c | 73 +++++++++++++++++++++++++++++++++++++------
configs/taurus_defconfig | 5 +--
include/configs/taurus.h | 54 +++++++++++++++++++++++++++++++-
4 files changed, 120 insertions(+), 13 deletions(-)
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 7b20fab..abe1317 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -128,6 +128,7 @@ config TARGET_CORVUS
bool "Support corvus"
config TARGET_TAURUS
+ select SUPPORT_SPL
bool "Support taurus"
config TARGET_STAMP9G20
diff --git a/board/siemens/taurus/taurus.c b/board/siemens/taurus/taurus.c
index 76609c7..2a4f40f 100644
--- a/board/siemens/taurus/taurus.c
+++ b/board/siemens/taurus/taurus.c
@@ -21,6 +21,8 @@
#include <asm/arch/at91_rstc.h>
#include <asm/arch/gpio.h>
#include <asm/arch/at91sam9_sdramc.h>
+#include <asm/arch/clk.h>
+#include <linux/mtd/nand.h>
#include <atmel_mci.h>
#include <asm/arch/at91_spi.h>
#include <spi.h>
@@ -30,7 +32,6 @@
DECLARE_GLOBAL_DATA_PTR;
-#ifdef CONFIG_CMD_NAND
static void taurus_nand_hw_init(void)
{
struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
@@ -63,15 +64,68 @@ static void taurus_nand_hw_init(void)
/* Enable NandFlash */
at91_set_gpio_output(CONFIG_SYS_NAND_ENABLE_PIN, 1);
}
+
+#if defined(CONFIG_SPL_BUILD)
+#include <spl.h>
+#include <nand.h>
+
+void at91_spl_board_init(void)
+{
+ taurus_nand_hw_init();
+
+ /* Configure recovery button PINs */
+ at91_set_gpio_input(AT91_PIN_PA31, 1);
+
+ /* check if button is pressed */
+ if (at91_get_gpio_value(AT91_PIN_PA31) == 0) {
+ u32 boot_device;
+
+ debug("Recovery button pressed\n");
+ boot_device = spl_boot_device();
+ switch (boot_device) {
+#ifdef CONFIG_SPL_NAND_SUPPORT
+ case BOOT_DEVICE_NAND:
+ nand_init();
+ spl_nand_erase_one(0, 0);
+ break;
+#endif
+ }
+ }
+}
+
+void mem_init(void)
+{
+ struct at91_matrix *ma = (struct at91_matrix *)ATMEL_BASE_MATRIX;
+ struct sdramc_reg setting;
+
+ at91_sdram_hw_init();
+ setting.cr = (AT91_SDRAMC_NC_9 |
+ AT91_SDRAMC_NR_13 |
+ AT91_SDRAMC_CAS_3 |
+ AT91_SDRAMC_NB_4 |
+ AT91_SDRAMC_DBW_32 |
+ AT91_SDRAMC_TWR_VAL(3) |
+ AT91_SDRAMC_TRC_VAL(9) |
+ AT91_SDRAMC_TRP_VAL(3) |
+ AT91_SDRAMC_TRCD_VAL(3) |
+ AT91_SDRAMC_TRAS_VAL(6) |
+ AT91_SDRAMC_TXSR_VAL(10));
+ setting.mdr = AT91_SDRAMC_MD_SDRAM;
+ setting.tr = (CONFIG_SYS_MASTER_CLOCK * 7) / 1000000;
+
+
+ writel(readl(&ma->ebicsa) | AT91_MATRIX_CS1A_SDRAMC |
+ AT91_MATRIX_VDDIOMSEL_3_3V | AT91_MATRIX_EBI_IOSR_SEL,
+ &ma->ebicsa);
+ sdramc_initialize(ATMEL_BASE_CS1, &setting);
+}
#endif
#ifdef CONFIG_MACB
static void taurus_macb_hw_init(void)
{
- struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
-
/* Enable EMAC clock */
- writel(1 << ATMEL_ID_EMAC0, &pmc->pcer);
+ at91_periph_clk_enable(ATMEL_ID_EMAC0);
/*
* Disable pull-up on:
@@ -119,12 +173,12 @@ int board_mmc_init(bd_t *bd)
int board_early_init_f(void)
{
- struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
-
/* Enable clocks for all PIOs */
- writel((1 << ATMEL_ID_PIOA) | (1 << ATMEL_ID_PIOB) |
- (1 << ATMEL_ID_PIOC),
- &pmc->pcer);
+ at91_periph_clk_enable(ATMEL_ID_PIOA);
+ at91_periph_clk_enable(ATMEL_ID_PIOB);
+ at91_periph_clk_enable(ATMEL_ID_PIOC);
+
+ at91_seriald_hw_init();
return 0;
}
@@ -149,7 +203,6 @@ int board_init(void)
/* adress of boot parameters */
gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
- at91_seriald_hw_init();
#ifdef CONFIG_CMD_NAND
taurus_nand_hw_init();
#endif
diff --git a/configs/taurus_defconfig b/configs/taurus_defconfig
index 9870048..438e25d 100644
--- a/configs/taurus_defconfig
+++ b/configs/taurus_defconfig
@@ -1,3 +1,4 @@
+CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9G20,MACH_TYPE=2067,BOARD_TAURUS"
-CONFIG_ARM=y
-CONFIG_TARGET_TAURUS=y
++S:CONFIG_ARM=y
++S:CONFIG_TARGET_TAURUS=y
diff --git a/include/configs/taurus.h b/include/configs/taurus.h
index ba9496f..21d60c1 100644
--- a/include/configs/taurus.h
+++ b/include/configs/taurus.h
@@ -34,7 +34,7 @@
*/
-#define CONFIG_SYS_TEXT_BASE 0x23f00000
+#define CONFIG_SYS_TEXT_BASE 0x21000000
/* ARM asynchronous clock */
#define CONFIG_SYS_AT91_SLOW_CLOCK 32768 /* slow clock xtal */
@@ -168,4 +168,56 @@
#define CONFIG_SYS_MALLOC_LEN \
ROUND(3 * CONFIG_ENV_SIZE + 128*1024, 0x1000)
+/* Defines for SPL */
+#define CONFIG_SPL_FRAMEWORK
+#define CONFIG_SPL_TEXT_BASE 0x0
+#define CONFIG_SPL_MAX_SIZE (11 * 1024)
+#define CONFIG_SPL_STACK (16 * 1024)
+
+#define CONFIG_SPL_BSS_START_ADDR CONFIG_SPL_MAX_SIZE
+#define CONFIG_SPL_BSS_MAX_SIZE (3 * 1024)
+
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+#define CONFIG_SPL_SERIAL_SUPPORT
+
+#define CONFIG_SPL_BOARD_INIT
+#define CONFIG_SPL_GPIO_SUPPORT
+#define CONFIG_SYS_NAND_ENABLE_PIN_SPL (2*32 + 14)
+#define CONFIG_SPL_NAND_SUPPORT
+#define CONFIG_SYS_USE_NANDFLASH 1
+#define CONFIG_SPL_NAND_DRIVERS
+#define CONFIG_SPL_NAND_BASE
+#define CONFIG_SPL_NAND_ECC
+#define CONFIG_SPL_NAND_RAW_ONLY
+#define CONFIG_SPL_NAND_SOFTECC
+#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x20000
+#define CONFIG_SYS_NAND_U_BOOT_SIZE 0x80000
+#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_NAND_U_BOOT_DST CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_NAND_5_ADDR_CYCLE
+
+#define CONFIG_SYS_NAND_SIZE (256*1024*1024)
+#define CONFIG_SYS_NAND_PAGE_SIZE 2048
+#define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024)
+#define CONFIG_SYS_NAND_PAGE_COUNT (CONFIG_SYS_NAND_BLOCK_SIZE / \
+ CONFIG_SYS_NAND_PAGE_SIZE)
+#define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS
+#define CONFIG_SYS_NAND_ECCSIZE 256
+#define CONFIG_SYS_NAND_ECCBYTES 3
+#define CONFIG_SYS_NAND_OOBSIZE 64
+#define CONFIG_SYS_NAND_ECCPOS { 40, 41, 42, 43, 44, 45, 46, 47, \
+ 48, 49, 50, 51, 52, 53, 54, 55, \
+ 56, 57, 58, 59, 60, 61, 62, 63, }
+
+
+#define CONFIG_SPL_ATMEL_SIZE
+#define CONFIG_SYS_MASTER_CLOCK 132096000
+#define AT91_PLL_LOCK_TIMEOUT 1000000
+#define CONFIG_SYS_AT91_PLLA 0x202A3F01
+#define CONFIG_SYS_MCKR 0x1300
+#define CONFIG_SYS_MCKR_CSS (0x02 | CONFIG_SYS_MCKR)
+#define CONFIG_SYS_AT91_PLLB 0x10193F05
+
+#define CONFIG_ATMEL_MATRIX_INIT
#endif
--
1.8.3.1
next prev parent reply other threads:[~2014-10-30 8:15 UTC|newest]
Thread overview: 23+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-10-30 8:14 [U-Boot] [v2 PATCH 0/12] arm, at91, spl: add spl support for the taurus and corvus boards Heiko Schocher
2014-10-30 8:14 ` [U-Boot] [v2 PATCH 01/12] spi, atmel: move CONFIG_SYS_SPI_WRITE_TOUT into common header Heiko Schocher
2014-10-30 8:14 ` [U-Boot] [v2 PATCH 02/12] arm, at91: add spi dataflash support for the taurus board Heiko Schocher
2014-10-30 8:14 ` [U-Boot] [v2 PATCH 03/12] arm, at91, mpddrc: fix typo in ddr2_init() Heiko Schocher
2014-10-31 1:55 ` Bo Shen
2014-10-31 5:33 ` Heiko Schocher
2014-10-30 8:14 ` [U-Boot] [v2 PATCH 04/12] arm, at91: compile mpddrc ram init code also for AT91SAM9M10G45 Heiko Schocher
2014-10-30 8:14 ` [U-Boot] [v2 PATCH 05/12] arm, at91: add missing ddr2 cr register MPDDRC_CR_EBISHARE define Heiko Schocher
2014-10-30 8:15 ` [U-Boot] [v2 PATCH 06/12] spl, nand: add option to boot raw u-boot.bin image only Heiko Schocher
2014-10-30 8:15 ` [U-Boot] [v2 PATCH 07/12] mtd: atmel_nand: add missign include Heiko Schocher
2014-10-30 8:15 ` [U-Boot] [v2 PATCH 08/12] spl, nand, atmel_nand: add erase one block function Heiko Schocher
2014-10-30 23:16 ` Scott Wood
2014-10-30 8:15 ` [U-Boot] [v2 PATCH 09/12] spl, mtd, nand, atmel_nand: invert device ready pin logic Heiko Schocher
2014-10-30 23:18 ` Scott Wood
2014-10-30 8:15 ` [U-Boot] [v2 PATCH 10/12] arm, spl, at91: add at91sam9260 and at91sam9g45 spl support Heiko Schocher
2014-10-30 10:17 ` Bo Shen
2014-10-30 11:41 ` Heiko Schocher
2014-10-31 1:55 ` Bo Shen
2014-10-31 1:50 ` Bo Shen
2014-10-31 6:03 ` Heiko Schocher
2014-10-31 6:08 ` Wolfgang Denk
2014-10-30 8:15 ` Heiko Schocher [this message]
2014-10-30 8:15 ` [U-Boot] [v2 PATCH 12/12] arm, spl, at91: add spl support for the corvus board Heiko Schocher
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1414656906-16632-12-git-send-email-hs@denx.de \
--to=hs@denx.de \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.