From: Hannes Reinecke <hare@suse.de>
To: James Bottomley <jbottomley@parallels.com>
Cc: Christoph Hellwig <hch@lst.de>,
Paolo@suse.de, "Bonzini <pbonzini"@redhat.com,
"David S. Miller" <davem@davemloft.net>,
linux-scsi@vger.kernel.org, Hannes Reinecke <hare@suse.de>
Subject: [PATCH 12/12] Replace tmscsim by am53c974
Date: Mon, 24 Nov 2014 15:37:30 +0100 [thread overview]
Message-ID: <1416839850-30475-13-git-send-email-hare@suse.de> (raw)
In-Reply-To: <1416839850-30475-1-git-send-email-hare@suse.de>
The am53c974 is a re-implementation of the tmscsim driver,
and provides the same functionality.
So remove the tmscsim driver and make am53c974 an alias to tmscsim.
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Hannes Reinecke <hare@suse.de>
---
MAINTAINERS | 7 +-
drivers/scsi/Kconfig | 16 -
drivers/scsi/Makefile | 1 -
drivers/scsi/am53c974.c | 1 +
drivers/scsi/tmscsim.c | 2626 -----------------------------------------------
drivers/scsi/tmscsim.h | 549 ----------
6 files changed, 4 insertions(+), 3196 deletions(-)
delete mode 100644 drivers/scsi/tmscsim.c
delete mode 100644 drivers/scsi/tmscsim.h
diff --git a/MAINTAINERS b/MAINTAINERS
index d206f37..d780e46 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -2862,11 +2862,10 @@ F: Documentation/networking/dmfe.txt
F: drivers/net/ethernet/dec/tulip/dmfe.c
DC390/AM53C974 SCSI driver
-M: Kurt Garloff <garloff@suse.de>
-W: http://www.garloff.de/kurt/linux/dc390/
-M: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
+M: Hannes Reinecke <hare@suse.de>
+L: linux-scsi@vger.kernel.org
S: Maintained
-F: drivers/scsi/tmscsim.*
+F: drivers/scsi/am53c974.c
DC395x SCSI driver
M: Oliver Neukum <oliver@neukum.org>
diff --git a/drivers/scsi/Kconfig b/drivers/scsi/Kconfig
index 519c3ef..f871a80 100644
--- a/drivers/scsi/Kconfig
+++ b/drivers/scsi/Kconfig
@@ -1341,22 +1341,6 @@ config SCSI_DC395x
To compile this driver as a module, choose M here: the
module will be called dc395x.
-config SCSI_DC390T
- tristate "Tekram DC390(T) and Am53/79C974 SCSI support"
- depends on PCI && SCSI
- ---help---
- This driver supports PCI SCSI host adapters based on the Am53C974A
- chip, e.g. Tekram DC390(T), DawiControl 2974 and some onboard
- PCscsi/PCnet (Am53/79C974) solutions.
-
- Documentation can be found in <file:Documentation/scsi/tmscsim.txt>.
-
- Note that this driver does NOT support Tekram DC390W/U/F, which are
- based on NCR/Symbios chips. Use "NCR53C8XX SCSI support" for those.
-
- To compile this driver as a module, choose M here: the
- module will be called tmscsim.
-
config SCSI_AM53C974
tristate "Tekram DC390(T) and Am53/79C974 SCSI support (new driver)"
depends on PCI && SCSI
diff --git a/drivers/scsi/Makefile b/drivers/scsi/Makefile
index 79a6571..a9f3fa8 100644
--- a/drivers/scsi/Makefile
+++ b/drivers/scsi/Makefile
@@ -100,7 +100,6 @@ obj-$(CONFIG_SCSI_EATA_PIO) += eata_pio.o
obj-$(CONFIG_SCSI_7000FASST) += wd7000.o
obj-$(CONFIG_SCSI_EATA) += eata.o
obj-$(CONFIG_SCSI_DC395x) += dc395x.o
-obj-$(CONFIG_SCSI_DC390T) += tmscsim.o
obj-$(CONFIG_SCSI_AM53C974) += esp_scsi.o am53c974.o
obj-$(CONFIG_MEGARAID_LEGACY) += megaraid.o
obj-$(CONFIG_MEGARAID_NEWGEN) += megaraid/
diff --git a/drivers/scsi/am53c974.c b/drivers/scsi/am53c974.c
index 25f0619..aa3e2c7 100644
--- a/drivers/scsi/am53c974.c
+++ b/drivers/scsi/am53c974.c
@@ -574,6 +574,7 @@ MODULE_DESCRIPTION("AM53C974 SCSI driver");
MODULE_AUTHOR("Hannes Reinecke <hare@suse.de>");
MODULE_LICENSE("GPL");
MODULE_VERSION(DRV_MODULE_VERSION);
+MODULE_ALIAS("tmscsim");
module_param(am53c974_debug, bool, 0644);
MODULE_PARM_DESC(am53c974_debug, "Enable debugging");
diff --git a/drivers/scsi/tmscsim.c b/drivers/scsi/tmscsim.c
deleted file mode 100644
index 844c9a0..0000000
--- a/drivers/scsi/tmscsim.c
+++ /dev/null
@@ -1,2626 +0,0 @@
-/************************************************************************
- * FILE NAME : TMSCSIM.C *
- * BY : C.L. Huang, ching@tekram.com.tw *
- * Description: Device Driver for Tekram DC-390(T) PCI SCSI *
- * Bus Master Host Adapter *
- * (C)Copyright 1995-1996 Tekram Technology Co., Ltd. *
- ************************************************************************
- * (C) Copyright: put under GNU GPL in 10/96 *
- * (see Documentation/scsi/tmscsim.txt) *
- ************************************************************************
- * $Id: tmscsim.c,v 2.60.2.30 2000/12/20 01:07:12 garloff Exp $ *
- * Enhancements and bugfixes by *
- * Kurt Garloff <kurt@garloff.de> <garloff@suse.de> *
- ************************************************************************
- * HISTORY: *
- * *
- * REV# DATE NAME DESCRIPTION *
- * 1.00 96/04/24 CLH First release *
- * 1.01 96/06/12 CLH Fixed bug of Media Change for Removable *
- * Device, scan all LUN. Support Pre2.0.10 *
- * 1.02 96/06/18 CLH Fixed bug of Command timeout ... *
- * 1.03 96/09/25 KG Added tmscsim_proc_info() *
- * 1.04 96/10/11 CLH Updating for support KV 2.0.x *
- * 1.05 96/10/18 KG Fixed bug in DC390_abort(null ptr deref)*
- * 1.06 96/10/25 KG Fixed module support *
- * 1.07 96/11/09 KG Fixed tmscsim_proc_info() *
- * 1.08 96/11/18 KG Fixed null ptr in DC390_Disconnect() *
- * 1.09 96/11/30 KG Added register the allocated IO space *
- * 1.10 96/12/05 CLH Modified tmscsim_proc_info(), and reset *
- * pending interrupt in DC390_detect() *
- * 1.11 97/02/05 KG/CLH Fixeds problem with partitions greater *
- * than 1GB *
- * 1.12 98/02/15 MJ Rewritten PCI probing *
- * 1.13 98/04/08 KG Support for non DC390, __initfunc decls,*
- * changed max devs from 10 to 16 *
- * 1.14a 98/05/05 KG Dynamic DCB allocation, add-single-dev *
- * for LUNs if LUN_SCAN (BIOS) not set *
- * runtime config using /proc interface *
- * 1.14b 98/05/06 KG eliminated cli (); sti (); spinlocks *
- * 1.14c 98/05/07 KG 2.0.x compatibility *
- * 1.20a 98/05/07 KG changed names of funcs to be consistent *
- * DC390_ (entry points), dc390_ (internal)*
- * reworked locking *
- * 1.20b 98/05/12 KG bugs: version, kfree, _ctmp *
- * debug output *
- * 1.20c 98/05/12 KG bugs: kfree, parsing, EEpromDefaults *
- * 1.20d 98/05/14 KG bugs: list linkage, clear flag after *
- * reset on startup, code cleanup *
- * 1.20e 98/05/15 KG spinlock comments, name space cleanup *
- * pLastDCB now part of ACB structure *
- * added stats, timeout for 2.1, TagQ bug *
- * RESET and INQUIRY interface commands *
- * 1.20f 98/05/18 KG spinlocks fixes, max_lun fix, free DCBs *
- * for missing LUNs, pending int *
- * 1.20g 98/05/19 KG Clean up: Avoid short *
- * 1.20h 98/05/21 KG Remove AdaptSCSIID, max_lun ... *
- * 1.20i 98/05/21 KG Aiiie: Bug with TagQMask *
- * 1.20j 98/05/24 KG Handle STAT_BUSY, handle pACB->pLinkDCB *
- * == 0 in remove_dev and DoingSRB_Done *
- * 1.20k 98/05/25 KG DMA_INT (experimental) *
- * 1.20l 98/05/27 KG remove DMA_INT; DMA_IDLE cmds added; *
- * 1.20m 98/06/10 KG glitch configurable; made some global *
- * vars part of ACB; use DC390_readX *
- * 1.20n 98/06/11 KG startup params *
- * 1.20o 98/06/15 KG added TagMaxNum to boot/module params *
- * Device Nr -> Idx, TagMaxNum power of 2 *
- * 1.20p 98/06/17 KG Docu updates. Reset depends on settings *
- * pci_set_master added; 2.0.xx: pcibios_* *
- * used instead of MechNum things ... *
- * 1.20q 98/06/23 KG Changed defaults. Added debug code for *
- * removable media and fixed it. TagMaxNum *
- * fixed for DC390. Locking: ACB, DRV for *
- * better IRQ sharing. Spelling: Queueing *
- * Parsing and glitch_cfg changes. Display *
- * real SyncSpeed value. Made DisConn *
- * functional (!) *
- * 1.20r 98/06/30 KG Debug macros, allow disabling DsCn, set *
- * BIT4 in CtrlR4, EN_PAGE_INT, 2.0 module *
- * param -1 fixed. *
- * 1.20s 98/08/20 KG Debug info on abort(), try to check PCI,*
- * phys_to_bus instead of phys_to_virt, *
- * fixed sel. process, fixed locking, *
- * added MODULE_XXX infos, changed IRQ *
- * request flags, disable DMA_INT *
- * 1.20t 98/09/07 KG TagQ report fixed; Write Erase DMA Stat;*
- * initfunc -> __init; better abort; *
- * Timeout for XFER_DONE & BLAST_COMPLETE; *
- * Allow up to 33 commands being processed *
- * 2.0a 98/10/14 KG Max Cmnds back to 17. DMA_Stat clearing *
- * all flags. Clear within while() loops *
- * in DataIn_0/Out_0. Null ptr in dumpinfo *
- * for pSRB==0. Better locking during init.*
- * bios_param() now respects part. table. *
- * 2.0b 98/10/24 KG Docu fixes. Timeout Msg in DMA Blast. *
- * Disallow illegal idx in INQUIRY/REMOVE *
- * 2.0c 98/11/19 KG Cleaned up detect/init for SMP boxes, *
- * Write Erase DMA (1.20t) caused problems *
- * 2.0d 98/12/25 KG Christmas release ;-) Message handling *
- * completely reworked. Handle target ini- *
- * tiated SDTR correctly. *
- * 2.0d1 99/01/25 KG Try to handle RESTORE_PTR *
- * 2.0d2 99/02/08 KG Check for failure of kmalloc, correct *
- * inclusion of scsicam.h, DelayReset *
- * 2.0d3 99/05/31 KG DRIVER_OK -> DID_OK, DID_NO_CONNECT, *
- * detect Target mode and warn. *
- * pcmd->result handling cleaned up. *
- * 2.0d4 99/06/01 KG Cleaned selection process. Found bug *
- * which prevented more than 16 tags. Now: *
- * 24. SDTR cleanup. Cleaner multi-LUN *
- * handling. Don't modify ControlRegs/FIFO *
- * when connected. *
- * 2.0d5 99/06/01 KG Clear DevID, Fix INQUIRY after cfg chg. *
- * 2.0d6 99/06/02 KG Added ADD special command to allow cfg. *
- * before detection. Reset SYNC_NEGO_DONE *
- * after a bus reset. *
- * 2.0d7 99/06/03 KG Fixed bugs wrt add,remove commands *
- * 2.0d8 99/06/04 KG Removed copying of cmnd into CmdBlock. *
- * Fixed Oops in _release(). *
- * 2.0d9 99/06/06 KG Also tag queue INQUIRY, T_U_R, ... *
- * Allow arb. no. of Tagged Cmnds. Max 32 *
- * 2.0d1099/06/20 KG TagMaxNo changes now honoured! Queueing *
- * clearified (renamed ..) TagMask handling*
- * cleaned. *
- * 2.0d1199/06/28 KG cmd->result now identical to 2.0d2 *
- * 2.0d1299/07/04 KG Changed order of processing in IRQ *
- * 2.0d1399/07/05 KG Don't update DCB fields if removed *
- * 2.0d1499/07/05 KG remove_dev: Move kfree() to the end *
- * 2.0d1599/07/12 KG use_new_eh_code: 0, ULONG -> UINT where *
- * appropriate *
- * 2.0d1699/07/13 KG Reenable StartSCSI interrupt, Retry msg *
- * 2.0d1799/07/15 KG Remove debug msg. Disable recfg. when *
- * there are queued cmnds *
- * 2.0d1899/07/18 KG Selection timeout: Don't requeue *
- * 2.0d1999/07/18 KG Abort: Only call scsi_done if dequeued *
- * 2.0d2099/07/19 KG Rst_Detect: DoingSRB_Done *
- * 2.0d2199/08/15 KG dev_id for request/free_irq, cmnd[0] for*
- * RETRY, SRBdone does DID_ABORT for the *
- * cmd passed by DC390_reset() *
- * 2.0d2299/08/25 KG dev_id fixed. can_queue: 42 *
- * 2.0d2399/08/25 KG Removed some debugging code. dev_id *
- * now is set to pACB. Use u8,u16,u32. *
- * 2.0d2499/11/14 KG Unreg. I/O if failed IRQ alloc. Call *
- * done () w/ DID_BAD_TARGET in case of *
- * missing DCB. We are old EH!! *
- * 2.0d2500/01/15 KG 2.3.3x compat from Andreas Schultz *
- * set unique_id. Disable RETRY message. *
- * 2.0d2600/01/29 KG Go to new EH. *
- * 2.0d2700/01/31 KG ... but maintain 2.0 compat. *
- * and fix DCB freeing *
- * 2.0d2800/02/14 KG Queue statistics fixed, dump special cmd*
- * Waiting_Timer for failed StartSCSI *
- * New EH: Don't return cmnds to ML on RST *
- * Use old EH (don't have new EH fns yet) *
- * Reset: Unlock, but refuse to queue *
- * 2.3 __setup function *
- * 2.0e 00/05/22 KG Return residual for 2.3 *
- * 2.0e1 00/05/25 KG Compile fixes for 2.3.99 *
- * 2.0e2 00/05/27 KG Jeff Garzik's pci_enable_device() *
- * 2.0e3 00/09/29 KG Some 2.4 changes. Don't try Sync Nego *
- * before INQUIRY has reported ability. *
- * Recognise INQUIRY as scanning command. *
- * 2.0e4 00/10/13 KG Allow compilation into 2.4 kernel *
- * 2.0e5 00/11/17 KG Store Inq.flags in DCB *
- * 2.0e6 00/11/22 KG 2.4 init function (Thx to O.Schumann) *
- * 2.4 PCI device table (Thx to A.Richter) *
- * 2.0e7 00/11/28 KG Allow overriding of BIOS settings *
- * 2.0f 00/12/20 KG Handle failed INQUIRYs during scan *
- * 2.1a 03/11/29 GL, KG Initial fixing for 2.6. Convert to *
- * use the current PCI-mapping API, update *
- * command-queuing. *
- * 2.1b 04/04/13 GL Fix for 64-bit platforms *
- * 2.1b1 04/01/31 GL (applied 05.04) Remove internal *
- * command-queuing. *
- * 2.1b2 04/02/01 CH (applied 05.04) Fix error-handling *
- * 2.1c 04/05/23 GL Update to use the new pci_driver API, *
- * some scsi EH updates, more cleanup. *
- * 2.1d 04/05/27 GL Moved setting of scan_devices to *
- * slave_alloc/_configure/_destroy, as *
- * suggested by CH. *
- ***********************************************************************/
-
-/* DEBUG options */
-//#define DC390_DEBUG0
-//#define DC390_DEBUG1
-//#define DC390_DCBDEBUG
-//#define DC390_PARSEDEBUG
-//#define DC390_REMOVABLEDEBUG
-//#define DC390_LOCKDEBUG
-
-//#define NOP do{}while(0)
-#define C_NOP
-
-/* Debug definitions */
-#ifdef DC390_DEBUG0
-# define DEBUG0(x) x
-#else
-# define DEBUG0(x) C_NOP
-#endif
-#ifdef DC390_DEBUG1
-# define DEBUG1(x) x
-#else
-# define DEBUG1(x) C_NOP
-#endif
-#ifdef DC390_DCBDEBUG
-# define DCBDEBUG(x) x
-#else
-# define DCBDEBUG(x) C_NOP
-#endif
-#ifdef DC390_PARSEDEBUG
-# define PARSEDEBUG(x) x
-#else
-# define PARSEDEBUG(x) C_NOP
-#endif
-#ifdef DC390_REMOVABLEDEBUG
-# define REMOVABLEDEBUG(x) x
-#else
-# define REMOVABLEDEBUG(x) C_NOP
-#endif
-#define DCBDEBUG1(x) C_NOP
-
-#include <linux/module.h>
-#include <linux/delay.h>
-#include <linux/signal.h>
-#include <linux/errno.h>
-#include <linux/kernel.h>
-#include <linux/ioport.h>
-#include <linux/pci.h>
-#include <linux/proc_fs.h>
-#include <linux/string.h>
-#include <linux/mm.h>
-#include <linux/blkdev.h>
-#include <linux/timer.h>
-#include <linux/interrupt.h>
-#include <linux/init.h>
-#include <linux/spinlock.h>
-#include <linux/slab.h>
-#include <asm/io.h>
-
-#include <scsi/scsi.h>
-#include <scsi/scsi_cmnd.h>
-#include <scsi/scsi_device.h>
-#include <scsi/scsi_host.h>
-#include <scsi/scsicam.h>
-#include <scsi/scsi_tcq.h>
-
-#define DC390_BANNER "Tekram DC390/AM53C974"
-#define DC390_VERSION "2.1d 2004-05-27"
-
-#define PCI_DEVICE_ID_AMD53C974 PCI_DEVICE_ID_AMD_SCSI
-
-#include "tmscsim.h"
-
-
-static void dc390_DataOut_0( struct dc390_acb* pACB, struct dc390_srb* pSRB, u8 *psstatus);
-static void dc390_DataIn_0( struct dc390_acb* pACB, struct dc390_srb* pSRB, u8 *psstatus);
-static void dc390_Command_0( struct dc390_acb* pACB, struct dc390_srb* pSRB, u8 *psstatus);
-static void dc390_Status_0( struct dc390_acb* pACB, struct dc390_srb* pSRB, u8 *psstatus);
-static void dc390_MsgOut_0( struct dc390_acb* pACB, struct dc390_srb* pSRB, u8 *psstatus);
-static void dc390_MsgIn_0( struct dc390_acb* pACB, struct dc390_srb* pSRB, u8 *psstatus);
-static void dc390_DataOutPhase( struct dc390_acb* pACB, struct dc390_srb* pSRB, u8 *psstatus);
-static void dc390_DataInPhase( struct dc390_acb* pACB, struct dc390_srb* pSRB, u8 *psstatus);
-static void dc390_CommandPhase( struct dc390_acb* pACB, struct dc390_srb* pSRB, u8 *psstatus);
-static void dc390_StatusPhase( struct dc390_acb* pACB, struct dc390_srb* pSRB, u8 *psstatus);
-static void dc390_MsgOutPhase( struct dc390_acb* pACB, struct dc390_srb* pSRB, u8 *psstatus);
-static void dc390_MsgInPhase( struct dc390_acb* pACB, struct dc390_srb* pSRB, u8 *psstatus);
-static void dc390_Nop_0( struct dc390_acb* pACB, struct dc390_srb* pSRB, u8 *psstatus);
-static void dc390_Nop_1( struct dc390_acb* pACB, struct dc390_srb* pSRB, u8 *psstatus);
-
-static void dc390_SetXferRate( struct dc390_acb* pACB, struct dc390_dcb* pDCB );
-static void dc390_Disconnect( struct dc390_acb* pACB );
-static void dc390_Reselect( struct dc390_acb* pACB );
-static void dc390_SRBdone( struct dc390_acb* pACB, struct dc390_dcb* pDCB, struct dc390_srb* pSRB );
-static void dc390_ScsiRstDetect( struct dc390_acb* pACB );
-static void dc390_EnableMsgOut_Abort(struct dc390_acb*, struct dc390_srb*);
-static void dc390_dumpinfo(struct dc390_acb* pACB, struct dc390_dcb* pDCB, struct dc390_srb* pSRB);
-static void dc390_ResetDevParam(struct dc390_acb* pACB);
-
-static u32 dc390_laststatus = 0;
-static u8 dc390_adapterCnt = 0;
-
-static int disable_clustering;
-module_param(disable_clustering, int, S_IRUGO);
-MODULE_PARM_DESC(disable_clustering, "If you experience problems with your devices, try setting to 1");
-
-/* Startup values, to be overriden on the commandline */
-static int tmscsim[] = {-2, -2, -2, -2, -2, -2};
-
-module_param_array(tmscsim, int, NULL, 0);
-MODULE_PARM_DESC(tmscsim, "Host SCSI ID, Speed (0=10MHz), Device Flags, Adapter Flags, Max Tags (log2(tags)-1), DelayReset (s)");
-MODULE_AUTHOR("C.L. Huang / Kurt Garloff");
-MODULE_DESCRIPTION("SCSI host adapter driver for Tekram DC390 and other AMD53C974A based PCI SCSI adapters");
-MODULE_LICENSE("GPL");
-MODULE_SUPPORTED_DEVICE("sd,sr,sg,st");
-
-static void *dc390_phase0[]={
- dc390_DataOut_0,
- dc390_DataIn_0,
- dc390_Command_0,
- dc390_Status_0,
- dc390_Nop_0,
- dc390_Nop_0,
- dc390_MsgOut_0,
- dc390_MsgIn_0,
- dc390_Nop_1
- };
-
-static void *dc390_phase1[]={
- dc390_DataOutPhase,
- dc390_DataInPhase,
- dc390_CommandPhase,
- dc390_StatusPhase,
- dc390_Nop_0,
- dc390_Nop_0,
- dc390_MsgOutPhase,
- dc390_MsgInPhase,
- dc390_Nop_1
- };
-
-#ifdef DC390_DEBUG1
-static char* dc390_p0_str[] = {
- "dc390_DataOut_0",
- "dc390_DataIn_0",
- "dc390_Command_0",
- "dc390_Status_0",
- "dc390_Nop_0",
- "dc390_Nop_0",
- "dc390_MsgOut_0",
- "dc390_MsgIn_0",
- "dc390_Nop_1"
- };
-
-static char* dc390_p1_str[] = {
- "dc390_DataOutPhase",
- "dc390_DataInPhase",
- "dc390_CommandPhase",
- "dc390_StatusPhase",
- "dc390_Nop_0",
- "dc390_Nop_0",
- "dc390_MsgOutPhase",
- "dc390_MsgInPhase",
- "dc390_Nop_1"
- };
-#endif
-
-static u8 dc390_eepromBuf[MAX_ADAPTER_NUM][EE_LEN];
-static u8 dc390_clock_period1[] = {4, 5, 6, 7, 8, 10, 13, 20};
-static u8 dc390_clock_speed[] = {100,80,67,57,50, 40, 31, 20};
-
-/***********************************************************************
- * Functions for the management of the internal structures
- * (DCBs, SRBs, Queueing)
- *
- **********************************************************************/
-static void inline dc390_start_segment(struct dc390_srb* pSRB)
-{
- struct scatterlist *psgl = pSRB->pSegmentList;
-
- /* start new sg segment */
- pSRB->SGBusAddr = sg_dma_address(psgl);
- pSRB->SGToBeXferLen = sg_dma_len(psgl);
-}
-
-static unsigned long inline dc390_advance_segment(struct dc390_srb* pSRB, u32 residue)
-{
- unsigned long xfer = pSRB->SGToBeXferLen - residue;
-
- /* xfer more bytes transferred */
- pSRB->SGBusAddr += xfer;
- pSRB->TotalXferredLen += xfer;
- pSRB->SGToBeXferLen = residue;
-
- return xfer;
-}
-
-static struct dc390_dcb __inline__ *dc390_findDCB ( struct dc390_acb* pACB, u8 id, u8 lun)
-{
- struct dc390_dcb* pDCB = pACB->pLinkDCB; if (!pDCB) return NULL;
- while (pDCB->TargetID != id || pDCB->TargetLUN != lun)
- {
- pDCB = pDCB->pNextDCB;
- if (pDCB == pACB->pLinkDCB)
- return NULL;
- }
- DCBDEBUG1( printk (KERN_DEBUG "DCB %p (%02x,%02x) found.\n", \
- pDCB, pDCB->TargetID, pDCB->TargetLUN));
- return pDCB;
-}
-
-/* Insert SRB oin top of free list */
-static __inline__ void dc390_Free_insert (struct dc390_acb* pACB, struct dc390_srb* pSRB)
-{
- DEBUG0(printk ("DC390: Free SRB %p\n", pSRB));
- pSRB->pNextSRB = pACB->pFreeSRB;
- pACB->pFreeSRB = pSRB;
-}
-
-static __inline__ void dc390_Going_append (struct dc390_dcb* pDCB, struct dc390_srb* pSRB)
-{
- pDCB->GoingSRBCnt++;
- DEBUG0(printk("DC390: Append SRB %p to Going\n", pSRB));
- /* Append to the list of Going commands */
- if( pDCB->pGoingSRB )
- pDCB->pGoingLast->pNextSRB = pSRB;
- else
- pDCB->pGoingSRB = pSRB;
-
- pDCB->pGoingLast = pSRB;
- /* No next one in sent list */
- pSRB->pNextSRB = NULL;
-}
-
-static __inline__ void dc390_Going_remove (struct dc390_dcb* pDCB, struct dc390_srb* pSRB)
-{
- DEBUG0(printk("DC390: Remove SRB %p from Going\n", pSRB));
- if (pSRB == pDCB->pGoingSRB)
- pDCB->pGoingSRB = pSRB->pNextSRB;
- else
- {
- struct dc390_srb* psrb = pDCB->pGoingSRB;
- while (psrb && psrb->pNextSRB != pSRB)
- psrb = psrb->pNextSRB;
- if (!psrb)
- { printk (KERN_ERR "DC390: Remove non-ex. SRB %p from Going!\n", pSRB); return; }
- psrb->pNextSRB = pSRB->pNextSRB;
- if (pSRB == pDCB->pGoingLast)
- pDCB->pGoingLast = psrb;
- }
- pDCB->GoingSRBCnt--;
-}
-
-static struct scatterlist* dc390_sg_build_single(struct scatterlist *sg, void *addr, unsigned int length)
-{
- sg_init_one(sg, addr, length);
- return sg;
-}
-
-/* Create pci mapping */
-static int dc390_pci_map (struct dc390_srb* pSRB)
-{
- int error = 0;
- struct scsi_cmnd *pcmd = pSRB->pcmd;
- struct pci_dev *pdev = pSRB->pSRBDCB->pDCBACB->pdev;
- dc390_cmd_scp_t* cmdp = ((dc390_cmd_scp_t*)(&pcmd->SCp));
-
- /* Map sense buffer */
- if (pSRB->SRBFlag & AUTO_REQSENSE) {
- pSRB->pSegmentList = dc390_sg_build_single(&pSRB->Segmentx, pcmd->sense_buffer, SCSI_SENSE_BUFFERSIZE);
- pSRB->SGcount = pci_map_sg(pdev, pSRB->pSegmentList, 1,
- DMA_FROM_DEVICE);
- cmdp->saved_dma_handle = sg_dma_address(pSRB->pSegmentList);
-
- /* TODO: error handling */
- if (pSRB->SGcount != 1)
- error = 1;
- DEBUG1(printk("%s(): Mapped sense buffer %p at %x\n", __func__, pcmd->sense_buffer, cmdp->saved_dma_handle));
- /* Map SG list */
- } else if (scsi_sg_count(pcmd)) {
- int nseg;
-
- nseg = scsi_dma_map(pcmd);
-
- pSRB->pSegmentList = scsi_sglist(pcmd);
- pSRB->SGcount = nseg;
-
- /* TODO: error handling */
- if (nseg < 0)
- error = 1;
- DEBUG1(printk("%s(): Mapped SG %p with %d (%d) elements\n",\
- __func__, scsi_sglist(pcmd), nseg, scsi_sg_count(pcmd)));
- /* Map single segment */
- } else
- pSRB->SGcount = 0;
-
- return error;
-}
-
-/* Remove pci mapping */
-static void dc390_pci_unmap (struct dc390_srb* pSRB)
-{
- struct scsi_cmnd *pcmd = pSRB->pcmd;
- struct pci_dev *pdev = pSRB->pSRBDCB->pDCBACB->pdev;
- DEBUG1(dc390_cmd_scp_t* cmdp = ((dc390_cmd_scp_t*)(&pcmd->SCp)));
-
- if (pSRB->SRBFlag) {
- pci_unmap_sg(pdev, &pSRB->Segmentx, 1, DMA_FROM_DEVICE);
- DEBUG1(printk("%s(): Unmapped sense buffer at %x\n", __func__, cmdp->saved_dma_handle));
- } else {
- scsi_dma_unmap(pcmd);
- DEBUG1(printk("%s(): Unmapped SG at %p with %d elements\n",
- __func__, scsi_sglist(pcmd), scsi_sg_count(pcmd)));
- }
-}
-
-static void __inline__
-dc390_freetag (struct dc390_dcb* pDCB, struct dc390_srb* pSRB)
-{
- if (pSRB->TagNumber != SCSI_NO_TAG) {
- pDCB->TagMask &= ~(1 << pSRB->TagNumber); /* free tag mask */
- pSRB->TagNumber = SCSI_NO_TAG;
- }
-}
-
-
-static int
-dc390_StartSCSI( struct dc390_acb* pACB, struct dc390_dcb* pDCB, struct dc390_srb* pSRB )
-{
- struct scsi_cmnd *scmd = pSRB->pcmd;
- struct scsi_device *sdev = scmd->device;
- u8 cmd, disc_allowed, try_sync_nego;
-
- pSRB->ScsiPhase = SCSI_NOP0;
-
- if (pACB->Connected)
- {
- // Should not happen normally
- printk (KERN_WARNING "DC390: Can't select when connected! (%08x,%02x)\n",
- pSRB->SRBState, pSRB->SRBFlag);
- pSRB->SRBState = SRB_READY;
- pACB->SelConn++;
- return 1;
- }
- if (time_before (jiffies, pACB->last_reset))
- {
- DEBUG0(printk ("DC390: We were just reset and don't accept commands yet!\n"));
- return 1;
- }
- /* KG: Moved pci mapping here */
- dc390_pci_map(pSRB);
- /* TODO: error handling */
- DC390_write8 (Scsi_Dest_ID, pDCB->TargetID);
- DC390_write8 (Sync_Period, pDCB->SyncPeriod);
- DC390_write8 (Sync_Offset, pDCB->SyncOffset);
- DC390_write8 (CtrlReg1, pDCB->CtrlR1);
- DC390_write8 (CtrlReg3, pDCB->CtrlR3);
- DC390_write8 (CtrlReg4, pDCB->CtrlR4);
- DC390_write8 (ScsiCmd, CLEAR_FIFO_CMD); /* Flush FIFO */
- DEBUG1(printk (KERN_INFO "DC390: Start SCSI command: %02x (Sync:%02x)\n",\
- scmd->cmnd[0], pDCB->SyncMode));
-
- /* Don't disconnect on AUTO_REQSENSE, cause it might be an
- * Contingent Allegiance Condition (6.6), where no tags should be used.
- * All other have to be allowed to disconnect to prevent Incorrect
- * Initiator Connection (6.8.2/6.5.2) */
- /* Changed KG, 99/06/06 */
- if (! (pSRB->SRBFlag & AUTO_REQSENSE))
- disc_allowed = pDCB->DevMode & EN_DISCONNECT_;
- else
- disc_allowed = 0;
-
- if ((pDCB->SyncMode & SYNC_ENABLE) && pDCB->TargetLUN == 0 && sdev->sdtr &&
- (((scmd->cmnd[0] == REQUEST_SENSE || (pSRB->SRBFlag & AUTO_REQSENSE)) &&
- !(pDCB->SyncMode & SYNC_NEGO_DONE)) || scmd->cmnd[0] == INQUIRY))
- try_sync_nego = 1;
- else
- try_sync_nego = 0;
-
- pSRB->MsgCnt = 0;
- cmd = SEL_W_ATN;
- DC390_write8 (ScsiFifo, IDENTIFY(disc_allowed, pDCB->TargetLUN));
- /* Change 99/05/31: Don't use tags when not disconnecting (BUSY) */
- if ((pDCB->SyncMode & EN_TAG_QUEUEING) && disc_allowed && (scmd->flags & SCMD_TAGGED)) {
- DC390_write8(ScsiFifo, MSG_SIMPLE_TAG);
- pDCB->TagMask |= 1 << scmd->request->tag;
- pSRB->TagNumber = scmd->request->tag;
- DC390_write8(ScsiFifo, scmd->request->tag);
- DEBUG1(printk(KERN_INFO "DC390: Select w/DisCn for SRB %p, block tag %02x\n", pSRB, tag[1]));
- cmd = SEL_W_ATN3;
- } else {
- /* No TagQ */
-//no_tag:
- DEBUG1(printk(KERN_INFO "DC390: Select w%s/DisCn for SRB %p, No TagQ\n", disc_allowed ? "" : "o", pSRB));
- }
-
- pSRB->SRBState = SRB_START_;
-
- if (try_sync_nego)
- {
- u8 Sync_Off = pDCB->SyncOffset;
- DEBUG0(printk (KERN_INFO "DC390: NEW Sync Nego code triggered (%i %i)\n", pDCB->TargetID, pDCB->TargetLUN));
- pSRB->MsgOutBuf[0] = EXTENDED_MESSAGE;
- pSRB->MsgOutBuf[1] = 3;
- pSRB->MsgOutBuf[2] = EXTENDED_SDTR;
- pSRB->MsgOutBuf[3] = pDCB->NegoPeriod;
- if (!(Sync_Off & 0x0f)) Sync_Off = SYNC_NEGO_OFFSET;
- pSRB->MsgOutBuf[4] = Sync_Off;
- pSRB->MsgCnt = 5;
- //pSRB->SRBState = SRB_MSGOUT_;
- pSRB->SRBState |= DO_SYNC_NEGO;
- cmd = SEL_W_ATN_STOP;
- }
-
- /* Command is written in CommandPhase, if SEL_W_ATN_STOP ... */
- if (cmd != SEL_W_ATN_STOP)
- {
- if( pSRB->SRBFlag & AUTO_REQSENSE )
- {
- DC390_write8 (ScsiFifo, REQUEST_SENSE);
- DC390_write8 (ScsiFifo, pDCB->TargetLUN << 5);
- DC390_write8 (ScsiFifo, 0);
- DC390_write8 (ScsiFifo, 0);
- DC390_write8 (ScsiFifo, SCSI_SENSE_BUFFERSIZE);
- DC390_write8 (ScsiFifo, 0);
- DEBUG1(printk (KERN_DEBUG "DC390: AutoReqSense !\n"));
- }
- else /* write cmnd to bus */
- {
- u8 *ptr; u8 i;
- ptr = (u8 *)scmd->cmnd;
- for (i = 0; i < scmd->cmd_len; i++)
- DC390_write8 (ScsiFifo, *(ptr++));
- }
- }
- DEBUG0(if (pACB->pActiveDCB) \
- printk (KERN_WARNING "DC390: ActiveDCB != 0\n"));
- DEBUG0(if (pDCB->pActiveSRB) \
- printk (KERN_WARNING "DC390: ActiveSRB != 0\n"));
- //DC390_write8 (DMA_Cmd, DMA_IDLE_CMD);
- if (DC390_read8 (Scsi_Status) & INTERRUPT)
- {
- dc390_freetag (pDCB, pSRB);
- DEBUG0(printk ("DC390: Interrupt during Start SCSI (target %02i-%02i)\n",
- scmd->device->id, (u8)scmd->device->lun));
- pSRB->SRBState = SRB_READY;
- //DC390_write8 (ScsiCmd, CLEAR_FIFO_CMD);
- pACB->SelLost++;
- return 1;
- }
- DC390_write8 (ScsiCmd, cmd);
- pACB->pActiveDCB = pDCB;
- pDCB->pActiveSRB = pSRB;
- pACB->Connected = 1;
- pSRB->ScsiPhase = SCSI_NOP1;
- return 0;
-}
-
-
-static void __inline__
-dc390_InvalidCmd(struct dc390_acb* pACB)
-{
- if (pACB->pActiveDCB->pActiveSRB->SRBState & (SRB_START_ | SRB_MSGOUT))
- DC390_write8(ScsiCmd, CLEAR_FIFO_CMD);
-}
-
-
-static irqreturn_t __inline__
-DC390_Interrupt(void *dev_id)
-{
- struct dc390_acb *pACB = dev_id;
- struct dc390_dcb *pDCB;
- struct dc390_srb *pSRB;
- u8 sstatus=0;
- u8 phase;
- void (*stateV)( struct dc390_acb*, struct dc390_srb*, u8 *);
- u8 istate, istatus;
-
- sstatus = DC390_read8 (Scsi_Status);
- if( !(sstatus & INTERRUPT) )
- return IRQ_NONE;
-
- DEBUG1(printk (KERN_DEBUG "sstatus=%02x,", sstatus));
-
- //DC390_write32 (DMA_ScsiBusCtrl, WRT_ERASE_DMA_STAT | EN_INT_ON_PCI_ABORT);
- //dstatus = DC390_read8 (DMA_Status);
- //DC390_write32 (DMA_ScsiBusCtrl, EN_INT_ON_PCI_ABORT);
-
- spin_lock_irq(pACB->pScsiHost->host_lock);
-
- istate = DC390_read8 (Intern_State);
- istatus = DC390_read8 (INT_Status); /* This clears Scsi_Status, Intern_State and INT_Status ! */
-
- DEBUG1(printk (KERN_INFO "Istatus(Res,Inv,Dis,Serv,Succ,ReS,SelA,Sel)=%02x,",istatus));
- dc390_laststatus &= ~0x00ffffff;
- dc390_laststatus |= /* dstatus<<24 | */ sstatus<<16 | istate<<8 | istatus;
-
- if (sstatus & ILLEGAL_OP_ERR)
- {
- printk ("DC390: Illegal Operation detected (%08x)!\n", dc390_laststatus);
- dc390_dumpinfo (pACB, pACB->pActiveDCB, pACB->pActiveDCB->pActiveSRB);
- }
-
- else if (istatus & INVALID_CMD)
- {
- printk ("DC390: Invalid Command detected (%08x)!\n", dc390_laststatus);
- dc390_InvalidCmd( pACB );
- goto unlock;
- }
-
- if (istatus & SCSI_RESET)
- {
- dc390_ScsiRstDetect( pACB );
- goto unlock;
- }
-
- if (istatus & DISCONNECTED)
- {
- dc390_Disconnect( pACB );
- goto unlock;
- }
-
- if (istatus & RESELECTED)
- {
- dc390_Reselect( pACB );
- goto unlock;
- }
-
- else if (istatus & (SELECTED | SEL_ATTENTION))
- {
- printk (KERN_ERR "DC390: Target mode not supported!\n");
- goto unlock;
- }
-
- if (istatus & (SUCCESSFUL_OP|SERVICE_REQUEST) )
- {
- pDCB = pACB->pActiveDCB;
- if (!pDCB)
- {
- printk (KERN_ERR "DC390: Suc. op/ Serv. req: pActiveDCB = 0!\n");
- goto unlock;
- }
- pSRB = pDCB->pActiveSRB;
- if( pDCB->DCBFlag & ABORT_DEV_ )
- dc390_EnableMsgOut_Abort (pACB, pSRB);
-
- phase = pSRB->ScsiPhase;
- DEBUG1(printk (KERN_INFO "DC390: [%i]%s(0) (%02x)\n", phase, dc390_p0_str[phase], sstatus));
- stateV = (void *) dc390_phase0[phase];
- ( *stateV )( pACB, pSRB, &sstatus );
-
- pSRB->ScsiPhase = sstatus & 7;
- phase = (u8) sstatus & 7;
- DEBUG1(printk (KERN_INFO "DC390: [%i]%s(1) (%02x)\n", phase, dc390_p1_str[phase], sstatus));
- stateV = (void *) dc390_phase1[phase];
- ( *stateV )( pACB, pSRB, &sstatus );
- }
-
- unlock:
- spin_unlock_irq(pACB->pScsiHost->host_lock);
- return IRQ_HANDLED;
-}
-
-static irqreturn_t do_DC390_Interrupt(int irq, void *dev_id)
-{
- irqreturn_t ret;
- DEBUG1(printk (KERN_INFO "DC390: Irq (%i) caught: ", irq));
- /* Locking is done in DC390_Interrupt */
- ret = DC390_Interrupt(dev_id);
- DEBUG1(printk (".. IRQ returned\n"));
- return ret;
-}
-
-static void
-dc390_DataOut_0(struct dc390_acb* pACB, struct dc390_srb* pSRB, u8 *psstatus)
-{
- u8 sstatus;
- u32 ResidCnt;
- u8 dstate = 0;
-
- sstatus = *psstatus;
-
- if( !(pSRB->SRBState & SRB_XFERPAD) )
- {
- if( sstatus & (PARITY_ERR | ILLEGAL_OP_ERR) )
- pSRB->SRBStatus |= PARITY_ERROR;
-
- if( sstatus & COUNT_2_ZERO )
- {
- unsigned long timeout = jiffies + HZ;
-
- /* Function called from the ISR with the host_lock held and interrupts disabled */
- if (pSRB->SGToBeXferLen)
- while (time_before(jiffies, timeout) && !((dstate = DC390_read8 (DMA_Status)) & DMA_XFER_DONE)) {
- spin_unlock_irq(pACB->pScsiHost->host_lock);
- udelay(50);
- spin_lock_irq(pACB->pScsiHost->host_lock);
- }
- if (!time_before(jiffies, timeout))
- printk (KERN_CRIT "DC390: Deadlock in DataOut_0: DMA aborted unfinished: %06x bytes remain!!\n",
- DC390_read32 (DMA_Wk_ByteCntr));
- dc390_laststatus &= ~0xff000000;
- dc390_laststatus |= dstate << 24;
- pSRB->TotalXferredLen += pSRB->SGToBeXferLen;
- pSRB->SGIndex++;
- if( pSRB->SGIndex < pSRB->SGcount )
- {
- pSRB->pSegmentList++;
-
- dc390_start_segment(pSRB);
- }
- else
- pSRB->SGToBeXferLen = 0;
- }
- else
- {
- ResidCnt = ((u32) DC390_read8 (Current_Fifo) & 0x1f) +
- (((u32) DC390_read8 (CtcReg_High) << 16) |
- ((u32) DC390_read8 (CtcReg_Mid) << 8) |
- (u32) DC390_read8 (CtcReg_Low));
-
- dc390_advance_segment(pSRB, ResidCnt);
- }
- }
- if ((*psstatus & 7) != SCSI_DATA_OUT)
- {
- DC390_write8 (DMA_Cmd, WRITE_DIRECTION+DMA_IDLE_CMD);
- DC390_write8 (ScsiCmd, CLEAR_FIFO_CMD);
- }
-}
-
-static void
-dc390_DataIn_0(struct dc390_acb* pACB, struct dc390_srb* pSRB, u8 *psstatus)
-{
- u8 sstatus, residual, bval;
- u32 ResidCnt, i;
- unsigned long xferCnt;
-
- sstatus = *psstatus;
-
- if( !(pSRB->SRBState & SRB_XFERPAD) )
- {
- if( sstatus & (PARITY_ERR | ILLEGAL_OP_ERR))
- pSRB->SRBStatus |= PARITY_ERROR;
-
- if( sstatus & COUNT_2_ZERO )
- {
- int dstate = 0;
- unsigned long timeout = jiffies + HZ;
-
- /* Function called from the ISR with the host_lock held and interrupts disabled */
- if (pSRB->SGToBeXferLen)
- while (time_before(jiffies, timeout) && !((dstate = DC390_read8 (DMA_Status)) & DMA_XFER_DONE)) {
- spin_unlock_irq(pACB->pScsiHost->host_lock);
- udelay(50);
- spin_lock_irq(pACB->pScsiHost->host_lock);
- }
- if (!time_before(jiffies, timeout)) {
- printk (KERN_CRIT "DC390: Deadlock in DataIn_0: DMA aborted unfinished: %06x bytes remain!!\n",
- DC390_read32 (DMA_Wk_ByteCntr));
- printk (KERN_CRIT "DC390: DataIn_0: DMA State: %i\n", dstate);
- }
- dc390_laststatus &= ~0xff000000;
- dc390_laststatus |= dstate << 24;
- DEBUG1(ResidCnt = ((unsigned long) DC390_read8 (CtcReg_High) << 16) \
- + ((unsigned long) DC390_read8 (CtcReg_Mid) << 8) \
- + ((unsigned long) DC390_read8 (CtcReg_Low)));
- DEBUG1(printk (KERN_DEBUG "Count_2_Zero (ResidCnt=%u,ToBeXfer=%lu),", ResidCnt, pSRB->SGToBeXferLen));
-
- DC390_write8 (DMA_Cmd, READ_DIRECTION+DMA_IDLE_CMD);
-
- pSRB->TotalXferredLen += pSRB->SGToBeXferLen;
- pSRB->SGIndex++;
- if( pSRB->SGIndex < pSRB->SGcount )
- {
- pSRB->pSegmentList++;
-
- dc390_start_segment(pSRB);
- }
- else
- pSRB->SGToBeXferLen = 0;
- }
- else /* phase changed */
- {
- residual = 0;
- bval = DC390_read8 (Current_Fifo);
- while( bval & 0x1f )
- {
- DEBUG1(printk (KERN_DEBUG "Check for residuals,"));
- if( (bval & 0x1f) == 1 )
- {
- for(i=0; i < 0x100; i++)
- {
- bval = DC390_read8 (Current_Fifo);
- if( !(bval & 0x1f) )
- goto din_1;
- else if( i == 0x0ff )
- {
- residual = 1; /* ;1 residual byte */
- goto din_1;
- }
- }
- }
- else
- bval = DC390_read8 (Current_Fifo);
- }
-din_1:
- DC390_write8 (DMA_Cmd, READ_DIRECTION+DMA_BLAST_CMD);
- for (i = 0xa000; i; i--)
- {
- bval = DC390_read8 (DMA_Status);
- if (bval & BLAST_COMPLETE)
- break;
- }
- /* It seems a DMA Blast abort isn't that bad ... */
- if (!i) printk (KERN_ERR "DC390: DMA Blast aborted unfinished!\n");
- //DC390_write8 (DMA_Cmd, READ_DIRECTION+DMA_IDLE_CMD);
- dc390_laststatus &= ~0xff000000;
- dc390_laststatus |= bval << 24;
-
- DEBUG1(printk (KERN_DEBUG "Blast: Read %i times DMA_Status %02x", 0xa000-i, bval));
- ResidCnt = (((u32) DC390_read8 (CtcReg_High) << 16) |
- ((u32) DC390_read8 (CtcReg_Mid) << 8)) |
- (u32) DC390_read8 (CtcReg_Low);
-
- xferCnt = dc390_advance_segment(pSRB, ResidCnt);
-
- if (residual) {
- size_t count = 1;
- size_t offset = pSRB->SGBusAddr - sg_dma_address(pSRB->pSegmentList);
- unsigned long flags;
- u8 *ptr;
-
- bval = DC390_read8 (ScsiFifo); /* get one residual byte */
-
- local_irq_save(flags);
- ptr = scsi_kmap_atomic_sg(pSRB->pSegmentList, pSRB->SGcount, &offset, &count);
- if (likely(ptr)) {
- *(ptr + offset) = bval;
- scsi_kunmap_atomic_sg(ptr);
- }
- local_irq_restore(flags);
- WARN_ON(!ptr);
-
- /* 1 more byte read */
- xferCnt += dc390_advance_segment(pSRB, pSRB->SGToBeXferLen - 1);
- }
- DEBUG1(printk (KERN_DEBUG "Xfered: %lu, Total: %lu, Remaining: %lu\n", xferCnt,\
- pSRB->TotalXferredLen, pSRB->SGToBeXferLen));
- }
- }
- if ((*psstatus & 7) != SCSI_DATA_IN)
- {
- DC390_write8 (ScsiCmd, CLEAR_FIFO_CMD);
- DC390_write8 (DMA_Cmd, READ_DIRECTION+DMA_IDLE_CMD);
- }
-}
-
-static void
-dc390_Command_0( struct dc390_acb* pACB, struct dc390_srb* pSRB, u8 *psstatus)
-{
-}
-
-static void
-dc390_Status_0( struct dc390_acb* pACB, struct dc390_srb* pSRB, u8 *psstatus)
-{
-
- pSRB->TargetStatus = DC390_read8 (ScsiFifo);
- //udelay (1);
- pSRB->EndMessage = DC390_read8 (ScsiFifo); /* get message */
-
- *psstatus = SCSI_NOP0;
- pSRB->SRBState = SRB_COMPLETED;
- DC390_write8 (ScsiCmd, MSG_ACCEPTED_CMD);
-}
-
-static void
-dc390_MsgOut_0( struct dc390_acb* pACB, struct dc390_srb* pSRB, u8 *psstatus)
-{
- if( pSRB->SRBState & (SRB_UNEXPECT_RESEL+SRB_ABORT_SENT) )
- *psstatus = SCSI_NOP0;
- //DC390_write8 (DMA_Cmd, DMA_IDLE_CMD);
-}
-
-
-static void __inline__
-dc390_reprog (struct dc390_acb* pACB, struct dc390_dcb* pDCB)
-{
- DC390_write8 (Sync_Period, pDCB->SyncPeriod);
- DC390_write8 (Sync_Offset, pDCB->SyncOffset);
- DC390_write8 (CtrlReg3, pDCB->CtrlR3);
- DC390_write8 (CtrlReg4, pDCB->CtrlR4);
- dc390_SetXferRate (pACB, pDCB);
-}
-
-
-#ifdef DC390_DEBUG0
-static void
-dc390_printMsg (u8 *MsgBuf, u8 len)
-{
- int i;
- printk (" %02x", MsgBuf[0]);
- for (i = 1; i < len; i++)
- printk (" %02x", MsgBuf[i]);
- printk ("\n");
-}
-#endif
-
-#define DC390_ENABLE_MSGOUT DC390_write8 (ScsiCmd, SET_ATN_CMD)
-
-/* reject_msg */
-static void __inline__
-dc390_MsgIn_reject (struct dc390_acb* pACB, struct dc390_srb* pSRB)
-{
- pSRB->MsgOutBuf[0] = MESSAGE_REJECT;
- pSRB->MsgCnt = 1;
- DC390_ENABLE_MSGOUT;
- DEBUG0 (printk (KERN_INFO "DC390: Reject message\n"));
-}
-
-/* abort command */
-static void
-dc390_EnableMsgOut_Abort ( struct dc390_acb* pACB, struct dc390_srb* pSRB )
-{
- pSRB->MsgOutBuf[0] = ABORT;
- pSRB->MsgCnt = 1; DC390_ENABLE_MSGOUT;
- pSRB->pSRBDCB->DCBFlag &= ~ABORT_DEV_;
-}
-
-static struct dc390_srb*
-dc390_MsgIn_QTag (struct dc390_acb* pACB, struct dc390_dcb* pDCB, s8 tag)
-{
- struct dc390_srb* pSRB = pDCB->pGoingSRB;
-
- if (pSRB)
- {
- struct scsi_cmnd *scmd = scsi_find_tag(pSRB->pcmd->device, tag);
- pSRB = (struct dc390_srb *)scmd->host_scribble;
-
- if (pDCB->DCBFlag & ABORT_DEV_)
- {
- pSRB->SRBState = SRB_ABORT_SENT;
- dc390_EnableMsgOut_Abort( pACB, pSRB );
- }
-
- if (!(pSRB->SRBState & SRB_DISCONNECT))
- goto mingx0;
-
- pDCB->pActiveSRB = pSRB;
- pSRB->SRBState = SRB_DATA_XFER;
- }
- else
- {
- mingx0:
- pSRB = pACB->pTmpSRB;
- pSRB->SRBState = SRB_UNEXPECT_RESEL;
- pDCB->pActiveSRB = pSRB;
- pSRB->MsgOutBuf[0] = ABORT_TAG;
- pSRB->MsgCnt = 1; DC390_ENABLE_MSGOUT;
- }
- return pSRB;
-}
-
-
-/* set async transfer mode */
-static void
-dc390_MsgIn_set_async (struct dc390_acb* pACB, struct dc390_srb* pSRB)
-{
- struct dc390_dcb* pDCB = pSRB->pSRBDCB;
- if (!(pSRB->SRBState & DO_SYNC_NEGO))
- printk (KERN_INFO "DC390: Target %i initiates Non-Sync?\n", pDCB->TargetID);
- pSRB->SRBState &= ~DO_SYNC_NEGO;
- pDCB->SyncMode &= ~(SYNC_ENABLE+SYNC_NEGO_DONE);
- pDCB->SyncPeriod = 0;
- pDCB->SyncOffset = 0;
- //pDCB->NegoPeriod = 50; /* 200ns <=> 5 MHz */
- pDCB->CtrlR3 = FAST_CLK; /* fast clock / normal scsi */
- pDCB->CtrlR4 &= 0x3f;
- pDCB->CtrlR4 |= pACB->glitch_cfg; /* glitch eater */
- dc390_reprog (pACB, pDCB);
-}
-
-/* set sync transfer mode */
-static void
-dc390_MsgIn_set_sync (struct dc390_acb* pACB, struct dc390_srb* pSRB)
-{
- u8 bval;
- u16 wval, wval1;
- struct dc390_dcb* pDCB = pSRB->pSRBDCB;
- u8 oldsyncperiod = pDCB->SyncPeriod;
- u8 oldsyncoffset = pDCB->SyncOffset;
-
- if (!(pSRB->SRBState & DO_SYNC_NEGO))
- {
- printk (KERN_INFO "DC390: Target %i initiates Sync: %ins %i ... answer ...\n",
- pDCB->TargetID, pSRB->MsgInBuf[3]<<2, pSRB->MsgInBuf[4]);
-
- /* reject */
- //dc390_MsgIn_reject (pACB, pSRB);
- //return dc390_MsgIn_set_async (pACB, pSRB);
-
- /* Reply with corrected SDTR Message */
- if (pSRB->MsgInBuf[4] > 15)
- {
- printk (KERN_INFO "DC390: Lower Sync Offset to 15\n");
- pSRB->MsgInBuf[4] = 15;
- }
- if (pSRB->MsgInBuf[3] < pDCB->NegoPeriod)
- {
- printk (KERN_INFO "DC390: Set sync nego period to %ins\n", pDCB->NegoPeriod << 2);
- pSRB->MsgInBuf[3] = pDCB->NegoPeriod;
- }
- memcpy (pSRB->MsgOutBuf, pSRB->MsgInBuf, 5);
- pSRB->MsgCnt = 5;
- DC390_ENABLE_MSGOUT;
- }
-
- pSRB->SRBState &= ~DO_SYNC_NEGO;
- pDCB->SyncMode |= SYNC_ENABLE+SYNC_NEGO_DONE;
- pDCB->SyncOffset &= 0x0f0;
- pDCB->SyncOffset |= pSRB->MsgInBuf[4];
- pDCB->NegoPeriod = pSRB->MsgInBuf[3];
-
- wval = (u16) pSRB->MsgInBuf[3];
- wval = wval << 2; wval -= 3; wval1 = wval / 25; /* compute speed */
- if( (wval1 * 25) != wval) wval1++;
- bval = FAST_CLK+FAST_SCSI; /* fast clock / fast scsi */
-
- pDCB->CtrlR4 &= 0x3f; /* Glitch eater: 12ns less than normal */
- if (pACB->glitch_cfg != NS_TO_GLITCH(0))
- pDCB->CtrlR4 |= NS_TO_GLITCH(((GLITCH_TO_NS(pACB->glitch_cfg)) - 1));
- else
- pDCB->CtrlR4 |= NS_TO_GLITCH(0);
- if (wval1 < 4) pDCB->CtrlR4 |= NS_TO_GLITCH(0); /* Ultra */
-
- if (wval1 >= 8)
- {
- wval1--; /* Timing computation differs by 1 from FAST_SCSI */
- bval = FAST_CLK; /* fast clock / normal scsi */
- pDCB->CtrlR4 |= pACB->glitch_cfg; /* glitch eater */
- }
-
- pDCB->CtrlR3 = bval;
- pDCB->SyncPeriod = (u8)wval1;
-
- if ((oldsyncperiod != wval1 || oldsyncoffset != pDCB->SyncOffset) && pDCB->TargetLUN == 0)
- {
- if (! (bval & FAST_SCSI)) wval1++;
- printk (KERN_INFO "DC390: Target %i: Sync transfer %i.%1i MHz, Offset %i\n", pDCB->TargetID,
- 40/wval1, ((40%wval1)*10+wval1/2)/wval1, pDCB->SyncOffset & 0x0f);
- }
-
- dc390_reprog (pACB, pDCB);
-}
-
-
-/* handle RESTORE_PTR */
-/* This doesn't look very healthy... to-be-fixed */
-static void
-dc390_restore_ptr (struct dc390_acb* pACB, struct dc390_srb* pSRB)
-{
- struct scsi_cmnd *pcmd = pSRB->pcmd;
- struct scatterlist *psgl;
- pSRB->TotalXferredLen = 0;
- pSRB->SGIndex = 0;
- if (scsi_sg_count(pcmd)) {
- size_t saved;
- pSRB->pSegmentList = scsi_sglist(pcmd);
- psgl = pSRB->pSegmentList;
- //dc390_pci_sync(pSRB);
-
- while (pSRB->TotalXferredLen + (unsigned long) sg_dma_len(psgl) < pSRB->Saved_Ptr)
- {
- pSRB->TotalXferredLen += (unsigned long) sg_dma_len(psgl);
- pSRB->SGIndex++;
- if( pSRB->SGIndex < pSRB->SGcount )
- {
- pSRB->pSegmentList++;
-
- dc390_start_segment(pSRB);
- }
- else
- pSRB->SGToBeXferLen = 0;
- }
-
- saved = pSRB->Saved_Ptr - pSRB->TotalXferredLen;
- pSRB->SGToBeXferLen -= saved;
- pSRB->SGBusAddr += saved;
- printk (KERN_INFO "DC390: Pointer restored. Segment %i, Total %li, Bus %08lx\n",
- pSRB->SGIndex, pSRB->Saved_Ptr, pSRB->SGBusAddr);
-
- } else {
- pSRB->SGcount = 0;
- printk (KERN_INFO "DC390: RESTORE_PTR message for Transfer without Scatter-Gather ??\n");
- }
-
- pSRB->TotalXferredLen = pSRB->Saved_Ptr;
-}
-
-
-/* According to the docs, the AM53C974 reads the message and
- * generates a Successful Operation IRQ before asserting ACK for
- * the last byte (how does it know whether it's the last ?) */
-/* The old code handled it in another way, indicating, that on
- * every message byte an IRQ is generated and every byte has to
- * be manually ACKed. Hmmm ? (KG, 98/11/28) */
-/* The old implementation was correct. Sigh! */
-
-/* Check if the message is complete */
-static u8 __inline__
-dc390_MsgIn_complete (u8 *msgbuf, u32 len)
-{
- if (*msgbuf == EXTENDED_MESSAGE)
- {
- if (len < 2) return 0;
- if (len < msgbuf[1] + 2) return 0;
- }
- else if (*msgbuf >= 0x20 && *msgbuf <= 0x2f) // two byte messages
- if (len < 2) return 0;
- return 1;
-}
-
-
-
-/* read and eval received messages */
-static void
-dc390_MsgIn_0( struct dc390_acb* pACB, struct dc390_srb* pSRB, u8 *psstatus)
-{
- struct dc390_dcb* pDCB = pACB->pActiveDCB;
-
- /* Read the msg */
-
- pSRB->MsgInBuf[pACB->MsgLen++] = DC390_read8 (ScsiFifo);
- //pSRB->SRBState = 0;
-
- /* Msg complete ? */
- if (dc390_MsgIn_complete (pSRB->MsgInBuf, pACB->MsgLen))
- {
- DEBUG0 (printk (KERN_INFO "DC390: MsgIn:"); dc390_printMsg (pSRB->MsgInBuf, pACB->MsgLen));
- /* Now eval the msg */
- switch (pSRB->MsgInBuf[0])
- {
- case DISCONNECT:
- pSRB->SRBState = SRB_DISCONNECT; break;
-
- case SIMPLE_QUEUE_TAG:
- case HEAD_OF_QUEUE_TAG:
- case ORDERED_QUEUE_TAG:
- pSRB = dc390_MsgIn_QTag (pACB, pDCB, pSRB->MsgInBuf[1]);
- break;
-
- case MESSAGE_REJECT:
- DC390_write8 (ScsiCmd, RESET_ATN_CMD);
- pDCB->NegoPeriod = 50; /* 200ns <=> 5 MHz */
- if( pSRB->SRBState & DO_SYNC_NEGO)
- dc390_MsgIn_set_async (pACB, pSRB);
- break;
-
- case EXTENDED_MESSAGE:
- /* reject every extended msg but SDTR */
- if (pSRB->MsgInBuf[1] != 3 || pSRB->MsgInBuf[2] != EXTENDED_SDTR)
- dc390_MsgIn_reject (pACB, pSRB);
- else
- {
- if (pSRB->MsgInBuf[3] == 0 || pSRB->MsgInBuf[4] == 0)
- dc390_MsgIn_set_async (pACB, pSRB);
- else
- dc390_MsgIn_set_sync (pACB, pSRB);
- }
-
- // nothing has to be done
- case COMMAND_COMPLETE: break;
-
- // SAVE POINTER may be ignored as we have the struct dc390_srb* associated with the
- // scsi command. Thanks, Gerard, for pointing it out.
- case SAVE_POINTERS:
- pSRB->Saved_Ptr = pSRB->TotalXferredLen;
- break;
- // The device might want to restart transfer with a RESTORE
- case RESTORE_POINTERS:
- DEBUG0(printk ("DC390: RESTORE POINTER message received ... try to handle\n"));
- dc390_restore_ptr (pACB, pSRB);
- break;
-
- // reject unknown messages
- default: dc390_MsgIn_reject (pACB, pSRB);
- }
-
- /* Clear counter and MsgIn state */
- pSRB->SRBState &= ~SRB_MSGIN;
- pACB->MsgLen = 0;
- }
-
- *psstatus = SCSI_NOP0;
- DC390_write8 (ScsiCmd, MSG_ACCEPTED_CMD);
- //DC390_write8 (DMA_Cmd, DMA_IDLE_CMD);
-}
-
-
-static void
-dc390_DataIO_Comm( struct dc390_acb* pACB, struct dc390_srb* pSRB, u8 ioDir)
-{
- unsigned long lval;
- struct dc390_dcb* pDCB = pACB->pActiveDCB;
-
- if (pSRB == pACB->pTmpSRB)
- {
- if (pDCB)
- printk(KERN_ERR "DC390: pSRB == pTmpSRB! (TagQ Error?) (%02i-%i)\n", pDCB->TargetID, pDCB->TargetLUN);
- else
- printk(KERN_ERR "DC390: pSRB == pTmpSRB! (TagQ Error?) (DCB 0!)\n");
-
- /* Try to recover - some broken disks react badly to tagged INQUIRY */
- if (pDCB && pACB->scan_devices && pDCB->GoingSRBCnt == 1) {
- pSRB = pDCB->pGoingSRB;
- pDCB->pActiveSRB = pSRB;
- } else {
- pSRB->pSRBDCB = pDCB;
- dc390_EnableMsgOut_Abort(pACB, pSRB);
- if (pDCB)
- pDCB->DCBFlag |= ABORT_DEV;
- return;
- }
- }
-
- if( pSRB->SGIndex < pSRB->SGcount )
- {
- DC390_write8 (DMA_Cmd, DMA_IDLE_CMD | ioDir);
- if( !pSRB->SGToBeXferLen )
- {
- dc390_start_segment(pSRB);
-
- DEBUG1(printk (KERN_DEBUG " DC390: Next SG segment."));
- }
- lval = pSRB->SGToBeXferLen;
- DEBUG1(printk (KERN_DEBUG " DC390: Start transfer: %li bytes (address %08lx)\n", lval, pSRB->SGBusAddr));
- DC390_write8 (CtcReg_Low, (u8) lval);
- lval >>= 8;
- DC390_write8 (CtcReg_Mid, (u8) lval);
- lval >>= 8;
- DC390_write8 (CtcReg_High, (u8) lval);
-
- DC390_write32 (DMA_XferCnt, pSRB->SGToBeXferLen);
- DC390_write32 (DMA_XferAddr, pSRB->SGBusAddr);
-
- //DC390_write8 (DMA_Cmd, DMA_IDLE_CMD | ioDir);
- pSRB->SRBState = SRB_DATA_XFER;
-
- DC390_write8 (ScsiCmd, DMA_COMMAND+INFO_XFER_CMD);
-
- DC390_write8 (DMA_Cmd, DMA_START_CMD | ioDir);
- //DEBUG1(DC390_write32 (DMA_ScsiBusCtrl, WRT_ERASE_DMA_STAT | EN_INT_ON_PCI_ABORT));
- //DEBUG1(printk (KERN_DEBUG "DC390: DMA_Status: %02x\n", DC390_read8 (DMA_Status)));
- //DEBUG1(DC390_write32 (DMA_ScsiBusCtrl, EN_INT_ON_PCI_ABORT));
- }
- else /* xfer pad */
- {
- if( pSRB->SGcount )
- {
- pSRB->AdaptStatus = H_OVER_UNDER_RUN;
- pSRB->SRBStatus |= OVER_RUN;
- DEBUG0(printk (KERN_WARNING " DC390: Overrun -"));
- }
- DEBUG0(printk (KERN_WARNING " Clear transfer pad \n"));
- DC390_write8 (CtcReg_Low, 0);
- DC390_write8 (CtcReg_Mid, 0);
- DC390_write8 (CtcReg_High, 0);
-
- pSRB->SRBState |= SRB_XFERPAD;
- DC390_write8 (ScsiCmd, DMA_COMMAND+XFER_PAD_BYTE);
-/*
- DC390_write8 (DMA_Cmd, DMA_IDLE_CMD | ioDir);
- DC390_write8 (DMA_Cmd, DMA_START_CMD | ioDir);
-*/
- }
-}
-
-
-static void
-dc390_DataOutPhase( struct dc390_acb* pACB, struct dc390_srb* pSRB, u8 *psstatus)
-{
- dc390_DataIO_Comm (pACB, pSRB, WRITE_DIRECTION);
-}
-
-static void
-dc390_DataInPhase( struct dc390_acb* pACB, struct dc390_srb* pSRB, u8 *psstatus)
-{
- dc390_DataIO_Comm (pACB, pSRB, READ_DIRECTION);
-}
-
-static void
-dc390_CommandPhase( struct dc390_acb* pACB, struct dc390_srb* pSRB, u8 *psstatus)
-{
- struct dc390_dcb* pDCB;
- u8 i, cnt;
- u8 *ptr;
-
- DC390_write8 (ScsiCmd, RESET_ATN_CMD);
- DC390_write8 (ScsiCmd, CLEAR_FIFO_CMD);
- if( !(pSRB->SRBFlag & AUTO_REQSENSE) )
- {
- cnt = (u8) pSRB->pcmd->cmd_len;
- ptr = (u8 *) pSRB->pcmd->cmnd;
- for(i=0; i < cnt; i++)
- DC390_write8 (ScsiFifo, *(ptr++));
- }
- else
- {
- DC390_write8 (ScsiFifo, REQUEST_SENSE);
- pDCB = pACB->pActiveDCB;
- DC390_write8 (ScsiFifo, pDCB->TargetLUN << 5);
- DC390_write8 (ScsiFifo, 0);
- DC390_write8 (ScsiFifo, 0);
- DC390_write8 (ScsiFifo, SCSI_SENSE_BUFFERSIZE);
- DC390_write8 (ScsiFifo, 0);
- DEBUG0(printk(KERN_DEBUG "DC390: AutoReqSense (CmndPhase)!\n"));
- }
- pSRB->SRBState = SRB_COMMAND;
- DC390_write8 (ScsiCmd, INFO_XFER_CMD);
-}
-
-static void
-dc390_StatusPhase( struct dc390_acb* pACB, struct dc390_srb* pSRB, u8 *psstatus)
-{
- DC390_write8 (ScsiCmd, CLEAR_FIFO_CMD);
- pSRB->SRBState = SRB_STATUS;
- DC390_write8 (ScsiCmd, INITIATOR_CMD_CMPLTE);
- //DC390_write8 (DMA_Cmd, DMA_IDLE_CMD);
-}
-
-static void
-dc390_MsgOutPhase( struct dc390_acb* pACB, struct dc390_srb* pSRB, u8 *psstatus)
-{
- u8 bval, i, cnt;
- u8 *ptr;
- struct dc390_dcb* pDCB;
-
- DC390_write8 (ScsiCmd, CLEAR_FIFO_CMD);
- pDCB = pACB->pActiveDCB;
- if( !(pSRB->SRBState & SRB_MSGOUT) )
- {
- cnt = pSRB->MsgCnt;
- if( cnt )
- {
- ptr = (u8 *) pSRB->MsgOutBuf;
- for(i=0; i < cnt; i++)
- DC390_write8 (ScsiFifo, *(ptr++));
- pSRB->MsgCnt = 0;
- if( (pDCB->DCBFlag & ABORT_DEV_) &&
- (pSRB->MsgOutBuf[0] == ABORT) )
- pSRB->SRBState = SRB_ABORT_SENT;
- }
- else
- {
- bval = ABORT; /* ??? MSG_NOP */
- if( (pSRB->pcmd->cmnd[0] == INQUIRY ) ||
- (pSRB->pcmd->cmnd[0] == REQUEST_SENSE) ||
- (pSRB->SRBFlag & AUTO_REQSENSE) )
- {
- if( pDCB->SyncMode & SYNC_ENABLE )
- goto mop1;
- }
- DC390_write8 (ScsiFifo, bval);
- }
- DC390_write8 (ScsiCmd, INFO_XFER_CMD);
- }
- else
- {
-mop1:
- printk (KERN_ERR "DC390: OLD Sync Nego code triggered! (%i %i)\n", pDCB->TargetID, pDCB->TargetLUN);
- DC390_write8 (ScsiFifo, EXTENDED_MESSAGE);
- DC390_write8 (ScsiFifo, 3); /* ;length of extended msg */
- DC390_write8 (ScsiFifo, EXTENDED_SDTR); /* ; sync nego */
- DC390_write8 (ScsiFifo, pDCB->NegoPeriod);
- if (pDCB->SyncOffset & 0x0f)
- DC390_write8 (ScsiFifo, pDCB->SyncOffset);
- else
- DC390_write8 (ScsiFifo, SYNC_NEGO_OFFSET);
- pSRB->SRBState |= DO_SYNC_NEGO;
- DC390_write8 (ScsiCmd, INFO_XFER_CMD);
- }
-}
-
-static void
-dc390_MsgInPhase( struct dc390_acb* pACB, struct dc390_srb* pSRB, u8 *psstatus)
-{
- DC390_write8 (ScsiCmd, CLEAR_FIFO_CMD);
- if( !(pSRB->SRBState & SRB_MSGIN) )
- {
- pSRB->SRBState &= ~SRB_DISCONNECT;
- pSRB->SRBState |= SRB_MSGIN;
- }
- DC390_write8 (ScsiCmd, INFO_XFER_CMD);
- //DC390_write8 (DMA_Cmd, DMA_IDLE_CMD);
-}
-
-static void
-dc390_Nop_0( struct dc390_acb* pACB, struct dc390_srb* pSRB, u8 *psstatus)
-{
-}
-
-static void
-dc390_Nop_1( struct dc390_acb* pACB, struct dc390_srb* pSRB, u8 *psstatus)
-{
-}
-
-
-static void
-dc390_SetXferRate( struct dc390_acb* pACB, struct dc390_dcb* pDCB )
-{
- u8 bval, i, cnt;
- struct dc390_dcb* ptr;
-
- if( !(pDCB->TargetLUN) )
- {
- if( !pACB->scan_devices )
- {
- ptr = pACB->pLinkDCB;
- cnt = pACB->DCBCnt;
- bval = pDCB->TargetID;
- for(i=0; i<cnt; i++)
- {
- if( ptr->TargetID == bval )
- {
- ptr->SyncPeriod = pDCB->SyncPeriod;
- ptr->SyncOffset = pDCB->SyncOffset;
- ptr->CtrlR3 = pDCB->CtrlR3;
- ptr->CtrlR4 = pDCB->CtrlR4;
- ptr->SyncMode = pDCB->SyncMode;
- }
- ptr = ptr->pNextDCB;
- }
- }
- }
- return;
-}
-
-
-static void
-dc390_Disconnect( struct dc390_acb* pACB )
-{
- struct dc390_dcb *pDCB;
- struct dc390_srb *pSRB, *psrb;
- u8 i, cnt;
-
- DEBUG0(printk(KERN_INFO "DISC,"));
-
- if (!pACB->Connected) printk(KERN_ERR "DC390: Disconnect not-connected bus?\n");
- pACB->Connected = 0;
- pDCB = pACB->pActiveDCB;
- if (!pDCB)
- {
- DEBUG0(printk(KERN_ERR "ACB:%p->ActiveDCB:%p IOPort:%04x IRQ:%02x !\n",\
- pACB, pDCB, pACB->IOPortBase, pACB->IRQLevel));
- mdelay(400);
- DC390_read8 (INT_Status); /* Reset Pending INT */
- DC390_write8 (ScsiCmd, EN_SEL_RESEL);
- return;
- }
- DC390_write8 (ScsiCmd, EN_SEL_RESEL);
- pSRB = pDCB->pActiveSRB;
- pACB->pActiveDCB = NULL;
- pSRB->ScsiPhase = SCSI_NOP0;
- if( pSRB->SRBState & SRB_UNEXPECT_RESEL )
- pSRB->SRBState = 0;
- else if( pSRB->SRBState & SRB_ABORT_SENT )
- {
- pDCB->TagMask = 0;
- pDCB->DCBFlag = 0;
- cnt = pDCB->GoingSRBCnt;
- pDCB->GoingSRBCnt = 0;
- pSRB = pDCB->pGoingSRB;
- for( i=0; i < cnt; i++)
- {
- psrb = pSRB->pNextSRB;
- dc390_Free_insert (pACB, pSRB);
- pSRB = psrb;
- }
- pDCB->pGoingSRB = NULL;
- }
- else
- {
- if( (pSRB->SRBState & (SRB_START_+SRB_MSGOUT)) ||
- !(pSRB->SRBState & (SRB_DISCONNECT+SRB_COMPLETED)) )
- { /* Selection time out */
- pSRB->AdaptStatus = H_SEL_TIMEOUT;
- pSRB->TargetStatus = 0;
- goto disc1;
- }
- else if (!(pSRB->SRBState & SRB_DISCONNECT) && (pSRB->SRBState & SRB_COMPLETED))
- {
-disc1:
- dc390_freetag (pDCB, pSRB);
- pDCB->pActiveSRB = NULL;
- pSRB->SRBState = SRB_FREE;
- dc390_SRBdone( pACB, pDCB, pSRB);
- }
- }
- pACB->MsgLen = 0;
-}
-
-
-static void
-dc390_Reselect( struct dc390_acb* pACB )
-{
- struct dc390_dcb* pDCB;
- struct dc390_srb* pSRB;
- u8 id, lun;
-
- DEBUG0(printk(KERN_INFO "RSEL,"));
- pACB->Connected = 1;
- pDCB = pACB->pActiveDCB;
- if( pDCB )
- { /* Arbitration lost but Reselection won */
- DEBUG0(printk ("DC390: (ActiveDCB != 0: Arb. lost but resel. won)!\n"));
- pSRB = pDCB->pActiveSRB;
- if( !( pACB->scan_devices ) )
- {
- struct scsi_cmnd *pcmd = pSRB->pcmd;
- scsi_set_resid(pcmd, scsi_bufflen(pcmd));
- SET_RES_DID(pcmd->result, DID_SOFT_ERROR);
- dc390_Going_remove(pDCB, pSRB);
- dc390_Free_insert(pACB, pSRB);
- pcmd->scsi_done (pcmd);
- DEBUG0(printk(KERN_DEBUG"DC390: Return SRB %p to free\n", pSRB));
- }
- }
- /* Get ID */
- lun = DC390_read8 (ScsiFifo);
- DEBUG0(printk ("Dev %02x,", lun));
- if (!(lun & (1 << pACB->pScsiHost->this_id)))
- printk (KERN_ERR "DC390: Reselection must select host adapter: %02x!\n", lun);
- else
- lun ^= 1 << pACB->pScsiHost->this_id; /* Mask AdapterID */
- id = 0; while (lun >>= 1) id++;
- /* Get LUN */
- lun = DC390_read8 (ScsiFifo);
- if (!(lun & IDENTIFY_BASE)) printk (KERN_ERR "DC390: Resel: Expect identify message!\n");
- lun &= 7;
- DEBUG0(printk ("(%02i-%i),", id, lun));
- pDCB = dc390_findDCB (pACB, id, lun);
- if (!pDCB)
- {
- printk (KERN_ERR "DC390: Reselect from non existing device (%02i-%i)\n",
- id, lun);
- return;
- }
- pACB->pActiveDCB = pDCB;
- /* TagQ: We expect a message soon, so never mind the exact SRB */
- if( pDCB->SyncMode & EN_TAG_QUEUEING )
- {
- pSRB = pACB->pTmpSRB;
- pDCB->pActiveSRB = pSRB;
- }
- else
- {
- pSRB = pDCB->pActiveSRB;
- if( !pSRB || !(pSRB->SRBState & SRB_DISCONNECT) )
- {
- pSRB= pACB->pTmpSRB;
- pSRB->SRBState = SRB_UNEXPECT_RESEL;
- printk (KERN_ERR "DC390: Reselect without outstanding cmnd (%02i-%i)\n",
- id, lun);
- pDCB->pActiveSRB = pSRB;
- dc390_EnableMsgOut_Abort ( pACB, pSRB );
- }
- else
- {
- if( pDCB->DCBFlag & ABORT_DEV_ )
- {
- pSRB->SRBState = SRB_ABORT_SENT;
- printk (KERN_INFO "DC390: Reselect: Abort (%02i-%i)\n",
- id, lun);
- dc390_EnableMsgOut_Abort( pACB, pSRB );
- }
- else
- pSRB->SRBState = SRB_DATA_XFER;
- }
- }
-
- DEBUG1(printk (KERN_DEBUG "Resel SRB(%p): TagNum (%02x)\n", pSRB, pSRB->TagNumber));
- pSRB->ScsiPhase = SCSI_NOP0;
- DC390_write8 (Scsi_Dest_ID, pDCB->TargetID);
- DC390_write8 (Sync_Period, pDCB->SyncPeriod);
- DC390_write8 (Sync_Offset, pDCB->SyncOffset);
- DC390_write8 (CtrlReg1, pDCB->CtrlR1);
- DC390_write8 (CtrlReg3, pDCB->CtrlR3);
- DC390_write8 (CtrlReg4, pDCB->CtrlR4); /* ; Glitch eater */
- DC390_write8 (ScsiCmd, MSG_ACCEPTED_CMD); /* ;to release the /ACK signal */
-}
-
-static int __inline__
-dc390_RequestSense(struct dc390_acb* pACB, struct dc390_dcb* pDCB, struct dc390_srb* pSRB)
-{
- struct scsi_cmnd *pcmd;
-
- pcmd = pSRB->pcmd;
-
- REMOVABLEDEBUG(printk(KERN_INFO "DC390: RequestSense(Cmd %02x, Id %02x, LUN %02x)\n",\
- pcmd->cmnd[0], pDCB->TargetID, pDCB->TargetLUN));
-
- pSRB->SRBFlag |= AUTO_REQSENSE;
- pSRB->SavedTotXLen = pSRB->TotalXferredLen;
- pSRB->AdaptStatus = 0;
- pSRB->TargetStatus = 0; /* CHECK_CONDITION<<1; */
-
- /* We are called from SRBdone, original PCI mapping has been removed
- * already, new one is set up from StartSCSI */
- pSRB->SGIndex = 0;
-
- pSRB->TotalXferredLen = 0;
- pSRB->SGToBeXferLen = 0;
- return dc390_StartSCSI(pACB, pDCB, pSRB);
-}
-
-
-static void
-dc390_SRBdone( struct dc390_acb* pACB, struct dc390_dcb* pDCB, struct dc390_srb* pSRB )
-{
- u8 status;
- struct scsi_cmnd *pcmd;
-
- pcmd = pSRB->pcmd;
- /* KG: Moved pci_unmap here */
- dc390_pci_unmap(pSRB);
-
- status = pSRB->TargetStatus;
-
- DEBUG0(printk (" SRBdone (%02x,%08x), SRB %p\n", status, pcmd->result, pSRB));
- if(pSRB->SRBFlag & AUTO_REQSENSE)
- { /* Last command was a Request Sense */
- pSRB->SRBFlag &= ~AUTO_REQSENSE;
- pSRB->AdaptStatus = 0;
- pSRB->TargetStatus = SAM_STAT_CHECK_CONDITION;
-
- //pcmd->result = MK_RES(DRIVER_SENSE,DID_OK,0,status);
- if (status == SAM_STAT_CHECK_CONDITION)
- pcmd->result = MK_RES_LNX(0, DID_BAD_TARGET, 0, /*CHECK_CONDITION*/0);
- else /* Retry */
- {
- if( pSRB->pcmd->cmnd[0] == TEST_UNIT_READY /* || pSRB->pcmd->cmnd[0] == START_STOP */)
- {
- /* Don't retry on TEST_UNIT_READY */
- pcmd->result = MK_RES_LNX(DRIVER_SENSE, DID_OK, 0, SAM_STAT_CHECK_CONDITION);
- REMOVABLEDEBUG(printk(KERN_INFO "Cmd=%02x, Result=%08x, XferL=%08x\n",pSRB->pcmd->cmnd[0],\
- (u32) pcmd->result, (u32) pSRB->TotalXferredLen));
- } else {
- SET_RES_DRV(pcmd->result, DRIVER_SENSE);
- //pSRB->ScsiCmdLen = (u8) (pSRB->Segment1[0] >> 8);
- DEBUG0 (printk ("DC390: RETRY (%02x), target %02i-%02i\n", pcmd->cmnd[0], pcmd->device->id, (u8)pcmd->device->lun));
- pSRB->TotalXferredLen = 0;
- SET_RES_DID(pcmd->result, DID_SOFT_ERROR);
- }
- }
- goto cmd_done;
- }
- if( status )
- {
- if (status == SAM_STAT_CHECK_CONDITION)
- {
- if (dc390_RequestSense(pACB, pDCB, pSRB)) {
- SET_RES_DID(pcmd->result, DID_ERROR);
- goto cmd_done;
- }
- return;
- }
- else if (status == SAM_STAT_TASK_SET_FULL)
- {
- scsi_track_queue_full(pcmd->device, pDCB->GoingSRBCnt - 1);
- DEBUG0 (printk ("DC390: RETRY (%02x), target %02i-%02i\n", pcmd->cmnd[0], pcmd->device->id, (u8)pcmd->device->lun));
- pSRB->TotalXferredLen = 0;
- SET_RES_DID(pcmd->result, DID_SOFT_ERROR);
- }
- else if (status == SAM_STAT_BUSY &&
- (pcmd->cmnd[0] == TEST_UNIT_READY || pcmd->cmnd[0] == INQUIRY) &&
- pACB->scan_devices)
- {
- pSRB->AdaptStatus = 0;
- pSRB->TargetStatus = status;
- pcmd->result = MK_RES(0,0,pSRB->EndMessage,/*status*/0);
- }
- else
- { /* Another error */
- pSRB->TotalXferredLen = 0;
- SET_RES_DID(pcmd->result, DID_SOFT_ERROR);
- goto cmd_done;
- }
- }
- else
- { /* Target status == 0 */
- status = pSRB->AdaptStatus;
- if (status == H_OVER_UNDER_RUN)
- {
- pSRB->TargetStatus = 0;
- SET_RES_DID(pcmd->result,DID_OK);
- SET_RES_MSG(pcmd->result,pSRB->EndMessage);
- }
- else if (status == H_SEL_TIMEOUT)
- {
- pcmd->result = MK_RES(0, DID_NO_CONNECT, 0, 0);
- /* Devices are removed below ... */
- }
- else if( pSRB->SRBStatus & PARITY_ERROR)
- {
- //pcmd->result = MK_RES(0,DID_PARITY,pSRB->EndMessage,0);
- SET_RES_DID(pcmd->result,DID_PARITY);
- SET_RES_MSG(pcmd->result,pSRB->EndMessage);
- }
- else /* No error */
- {
- pSRB->AdaptStatus = 0;
- pSRB->TargetStatus = 0;
- SET_RES_DID(pcmd->result,DID_OK);
- }
- }
-
-cmd_done:
- scsi_set_resid(pcmd, scsi_bufflen(pcmd) - pSRB->TotalXferredLen);
-
- dc390_Going_remove (pDCB, pSRB);
- /* Add to free list */
- dc390_Free_insert (pACB, pSRB);
-
- DEBUG0(printk (KERN_DEBUG "DC390: SRBdone: done\n"));
- pcmd->scsi_done (pcmd);
-
- return;
-}
-
-
-/* Remove all SRBs from Going list and inform midlevel */
-static void
-dc390_DoingSRB_Done(struct dc390_acb* pACB, struct scsi_cmnd *cmd)
-{
- struct dc390_dcb *pDCB, *pdcb;
- struct dc390_srb *psrb, *psrb2;
- int i;
- struct scsi_cmnd *pcmd;
-
- pDCB = pACB->pLinkDCB;
- pdcb = pDCB;
- if (! pdcb) return;
- do
- {
- psrb = pdcb->pGoingSRB;
- for (i = 0; i < pdcb->GoingSRBCnt; i++)
- {
- psrb2 = psrb->pNextSRB;
- pcmd = psrb->pcmd;
- dc390_Free_insert (pACB, psrb);
- psrb = psrb2;
- }
- pdcb->GoingSRBCnt = 0;
- pdcb->pGoingSRB = NULL;
- pdcb->TagMask = 0;
- pdcb = pdcb->pNextDCB;
- } while( pdcb != pDCB );
-}
-
-
-static void
-dc390_ResetSCSIBus( struct dc390_acb* pACB )
-{
- //DC390_write8 (ScsiCmd, RST_DEVICE_CMD);
- //udelay (250);
- //DC390_write8 (ScsiCmd, NOP_CMD);
-
- DC390_write8 (ScsiCmd, CLEAR_FIFO_CMD);
- DC390_write8 (DMA_Cmd, DMA_IDLE_CMD);
- DC390_write8 (ScsiCmd, RST_SCSI_BUS_CMD);
- pACB->Connected = 0;
-
- return;
-}
-
-static void
-dc390_ScsiRstDetect( struct dc390_acb* pACB )
-{
- printk ("DC390: Rst_Detect: laststat = %08x\n", dc390_laststatus);
- //DEBUG0(printk(KERN_INFO "RST_DETECT,"));
-
- DC390_write8 (DMA_Cmd, DMA_IDLE_CMD);
- /* Unlock before ? */
- /* delay half a second */
- udelay (1000);
- DC390_write8 (ScsiCmd, CLEAR_FIFO_CMD);
- pACB->last_reset = jiffies + 5*HZ/2
- + HZ * dc390_eepromBuf[pACB->AdapterIndex][EE_DELAY];
- pACB->Connected = 0;
-
- if( pACB->ACBFlag & RESET_DEV )
- pACB->ACBFlag |= RESET_DONE;
- else
- { /* Reset was issued by sb else */
- pACB->ACBFlag |= RESET_DETECT;
-
- dc390_ResetDevParam( pACB );
- dc390_DoingSRB_Done( pACB, NULL);
- //dc390_RecoverSRB( pACB );
- pACB->pActiveDCB = NULL;
- pACB->ACBFlag = 0;
- }
- return;
-}
-
-static int DC390_queuecommand_lck(struct scsi_cmnd *cmd,
- void (*done)(struct scsi_cmnd *))
-{
- struct scsi_device *sdev = cmd->device;
- struct dc390_acb *acb = (struct dc390_acb *)sdev->host->hostdata;
- struct dc390_dcb *dcb = sdev->hostdata;
- struct dc390_srb *srb;
-
- if (sdev->queue_depth <= dcb->GoingSRBCnt)
- goto device_busy;
- if (acb->pActiveDCB)
- goto host_busy;
- if (acb->ACBFlag & (RESET_DETECT|RESET_DONE|RESET_DEV))
- goto host_busy;
-
- srb = acb->pFreeSRB;
- if (unlikely(srb == NULL))
- goto host_busy;
-
- cmd->scsi_done = done;
- cmd->result = 0;
- acb->Cmds++;
-
- acb->pFreeSRB = srb->pNextSRB;
- srb->pNextSRB = NULL;
-
- srb->pSRBDCB = dcb;
- srb->pcmd = cmd;
- cmd->host_scribble = (char *)srb;
-
- srb->SGIndex = 0;
- srb->AdaptStatus = 0;
- srb->TargetStatus = 0;
- srb->MsgCnt = 0;
-
- srb->SRBStatus = 0;
- srb->SRBFlag = 0;
- srb->SRBState = 0;
- srb->TotalXferredLen = 0;
- srb->SGBusAddr = 0;
- srb->SGToBeXferLen = 0;
- srb->ScsiPhase = 0;
- srb->EndMessage = 0;
- srb->TagNumber = SCSI_NO_TAG;
-
- if (dc390_StartSCSI(acb, dcb, srb)) {
- dc390_Free_insert(acb, srb);
- goto host_busy;
- }
-
- dc390_Going_append(dcb, srb);
-
- return 0;
-
- host_busy:
- return SCSI_MLQUEUE_HOST_BUSY;
-
- device_busy:
- return SCSI_MLQUEUE_DEVICE_BUSY;
-}
-
-static DEF_SCSI_QCMD(DC390_queuecommand)
-
-static void dc390_dumpinfo (struct dc390_acb* pACB, struct dc390_dcb* pDCB, struct dc390_srb* pSRB)
-{
- struct pci_dev *pdev;
- u16 pstat;
-
- if (!pDCB) pDCB = pACB->pActiveDCB;
- if (!pSRB && pDCB) pSRB = pDCB->pActiveSRB;
-
- if (pSRB)
- {
- printk ("DC390: SRB: Xferred %08lx, Remain %08lx, State %08x, Phase %02x\n",
- pSRB->TotalXferredLen, pSRB->SGToBeXferLen, pSRB->SRBState,
- pSRB->ScsiPhase);
- printk ("DC390: AdpaterStatus: %02x, SRB Status %02x\n", pSRB->AdaptStatus, pSRB->SRBStatus);
- }
- printk ("DC390: Status of last IRQ (DMA/SC/Int/IRQ): %08x\n", dc390_laststatus);
- printk ("DC390: Register dump: SCSI block:\n");
- printk ("DC390: XferCnt Cmd Stat IntS IRQS FFIS Ctl1 Ctl2 Ctl3 Ctl4\n");
- printk ("DC390: %06x %02x %02x %02x",
- DC390_read8(CtcReg_Low) + (DC390_read8(CtcReg_Mid) << 8) + (DC390_read8(CtcReg_High) << 16),
- DC390_read8(ScsiCmd), DC390_read8(Scsi_Status), DC390_read8(Intern_State));
- printk (" %02x %02x %02x %02x %02x %02x\n",
- DC390_read8(INT_Status), DC390_read8(Current_Fifo), DC390_read8(CtrlReg1),
- DC390_read8(CtrlReg2), DC390_read8(CtrlReg3), DC390_read8(CtrlReg4));
- DC390_write32 (DMA_ScsiBusCtrl, WRT_ERASE_DMA_STAT | EN_INT_ON_PCI_ABORT);
- if (DC390_read8(Current_Fifo) & 0x1f)
- {
- printk ("DC390: FIFO:");
- while (DC390_read8(Current_Fifo) & 0x1f) printk (" %02x", DC390_read8(ScsiFifo));
- printk ("\n");
- }
- printk ("DC390: Register dump: DMA engine:\n");
- printk ("DC390: Cmd STrCnt SBusA WrkBC WrkAC Stat SBusCtrl\n");
- printk ("DC390: %02x %08x %08x %08x %08x %02x %08x\n",
- DC390_read8(DMA_Cmd), DC390_read32(DMA_XferCnt), DC390_read32(DMA_XferAddr),
- DC390_read32(DMA_Wk_ByteCntr), DC390_read32(DMA_Wk_AddrCntr),
- DC390_read8(DMA_Status), DC390_read32(DMA_ScsiBusCtrl));
- DC390_write32 (DMA_ScsiBusCtrl, EN_INT_ON_PCI_ABORT);
-
- pdev = pACB->pdev;
- pci_read_config_word(pdev, PCI_STATUS, &pstat);
- printk ("DC390: Register dump: PCI Status: %04x\n", pstat);
- printk ("DC390: In case of driver trouble read Documentation/scsi/tmscsim.txt\n");
-}
-
-
-static int DC390_abort(struct scsi_cmnd *cmd)
-{
- struct dc390_acb *pACB = (struct dc390_acb*) cmd->device->host->hostdata;
- struct dc390_dcb *pDCB = (struct dc390_dcb*) cmd->device->hostdata;
-
- scmd_printk(KERN_WARNING, cmd, "DC390: Abort command\n");
-
- /* abort() is too stupid for already sent commands at the moment.
- * If it's called we are in trouble anyway, so let's dump some info
- * into the syslog at least. (KG, 98/08/20,99/06/20) */
- dc390_dumpinfo(pACB, pDCB, NULL);
-
- pDCB->DCBFlag |= ABORT_DEV_;
- printk(KERN_INFO "DC390: Aborted.\n");
-
- return FAILED;
-}
-
-
-static void dc390_ResetDevParam( struct dc390_acb* pACB )
-{
- struct dc390_dcb *pDCB, *pdcb;
-
- pDCB = pACB->pLinkDCB;
- if (! pDCB) return;
- pdcb = pDCB;
- do
- {
- pDCB->SyncMode &= ~SYNC_NEGO_DONE;
- pDCB->SyncPeriod = 0;
- pDCB->SyncOffset = 0;
- pDCB->TagMask = 0;
- pDCB->CtrlR3 = FAST_CLK;
- pDCB->CtrlR4 &= NEGATE_REQACKDATA | CTRL4_RESERVED | NEGATE_REQACK;
- pDCB->CtrlR4 |= pACB->glitch_cfg;
- pDCB = pDCB->pNextDCB;
- }
- while( pdcb != pDCB );
- pACB->ACBFlag &= ~(RESET_DEV | RESET_DONE | RESET_DETECT);
-
-}
-
-static int DC390_bus_reset (struct scsi_cmnd *cmd)
-{
- struct dc390_acb* pACB = (struct dc390_acb*) cmd->device->host->hostdata;
- u8 bval;
-
- spin_lock_irq(cmd->device->host->host_lock);
-
- bval = DC390_read8(CtrlReg1) | DIS_INT_ON_SCSI_RST;
- DC390_write8(CtrlReg1, bval); /* disable IRQ on bus reset */
-
- pACB->ACBFlag |= RESET_DEV;
- dc390_ResetSCSIBus(pACB);
-
- dc390_ResetDevParam(pACB);
- mdelay(1);
- pACB->last_reset = jiffies + 3*HZ/2
- + HZ * dc390_eepromBuf[pACB->AdapterIndex][EE_DELAY];
-
- DC390_write8(ScsiCmd, CLEAR_FIFO_CMD);
- DC390_read8(INT_Status); /* Reset Pending INT */
-
- dc390_DoingSRB_Done(pACB, cmd);
-
- pACB->pActiveDCB = NULL;
- pACB->ACBFlag = 0;
-
- bval = DC390_read8(CtrlReg1) & ~DIS_INT_ON_SCSI_RST;
- DC390_write8(CtrlReg1, bval); /* re-enable interrupt */
-
- spin_unlock_irq(cmd->device->host->host_lock);
-
- return SUCCESS;
-}
-
-/**
- * dc390_slave_alloc - Called by the scsi mid layer to tell us about a new
- * scsi device that we need to deal with.
- *
- * @scsi_device: The new scsi device that we need to handle.
- */
-static int dc390_slave_alloc(struct scsi_device *scsi_device)
-{
- struct dc390_acb *pACB = (struct dc390_acb*) scsi_device->host->hostdata;
- struct dc390_dcb *pDCB, *pDCB2 = NULL;
- uint id = scsi_device->id;
- uint lun = scsi_device->lun;
-
- pDCB = kzalloc(sizeof(struct dc390_dcb), GFP_KERNEL);
- if (!pDCB)
- return -ENOMEM;
-
- if (!pACB->DCBCnt++) {
- pACB->pLinkDCB = pDCB;
- pACB->pDCBRunRobin = pDCB;
- } else {
- pACB->pLastDCB->pNextDCB = pDCB;
- }
-
- pDCB->pNextDCB = pACB->pLinkDCB;
- pACB->pLastDCB = pDCB;
-
- pDCB->pDCBACB = pACB;
- pDCB->TargetID = id;
- pDCB->TargetLUN = lun;
-
- /*
- * Some values are for all LUNs: Copy them
- * In a clean way: We would have an own structure for a SCSI-ID
- */
- if (lun && (pDCB2 = dc390_findDCB(pACB, id, 0))) {
- pDCB->DevMode = pDCB2->DevMode;
- pDCB->SyncMode = pDCB2->SyncMode & SYNC_NEGO_DONE;
- pDCB->SyncPeriod = pDCB2->SyncPeriod;
- pDCB->SyncOffset = pDCB2->SyncOffset;
- pDCB->NegoPeriod = pDCB2->NegoPeriod;
-
- pDCB->CtrlR3 = pDCB2->CtrlR3;
- pDCB->CtrlR4 = pDCB2->CtrlR4;
- } else {
- u8 index = pACB->AdapterIndex;
- PEEprom prom = (PEEprom) &dc390_eepromBuf[index][id << 2];
-
- pDCB->DevMode = prom->EE_MODE1;
- pDCB->NegoPeriod =
- (dc390_clock_period1[prom->EE_SPEED] * 25) >> 2;
- pDCB->CtrlR3 = FAST_CLK;
- pDCB->CtrlR4 = pACB->glitch_cfg | CTRL4_RESERVED;
- if (dc390_eepromBuf[index][EE_MODE2] & ACTIVE_NEGATION)
- pDCB->CtrlR4 |= NEGATE_REQACKDATA | NEGATE_REQACK;
- }
-
- if (pDCB->DevMode & SYNC_NEGO_)
- pDCB->SyncMode |= SYNC_ENABLE;
- else {
- pDCB->SyncMode = 0;
- pDCB->SyncOffset &= ~0x0f;
- }
-
- pDCB->CtrlR1 = pACB->pScsiHost->this_id;
- if (pDCB->DevMode & PARITY_CHK_)
- pDCB->CtrlR1 |= PARITY_ERR_REPO;
-
- pACB->scan_devices = 1;
- scsi_device->hostdata = pDCB;
- return 0;
-}
-
-/**
- * dc390_slave_destroy - Called by the scsi mid layer to tell us about a
- * device that is going away.
- *
- * @scsi_device: The scsi device that we need to remove.
- */
-static void dc390_slave_destroy(struct scsi_device *scsi_device)
-{
- struct dc390_acb* pACB = (struct dc390_acb*) scsi_device->host->hostdata;
- struct dc390_dcb* pDCB = (struct dc390_dcb*) scsi_device->hostdata;
- struct dc390_dcb* pPrevDCB = pACB->pLinkDCB;
-
- pACB->scan_devices = 0;
-
- BUG_ON(pDCB->GoingSRBCnt > 1);
-
- if (pDCB == pACB->pLinkDCB) {
- if (pACB->pLastDCB == pDCB) {
- pDCB->pNextDCB = NULL;
- pACB->pLastDCB = NULL;
- }
- pACB->pLinkDCB = pDCB->pNextDCB;
- } else {
- while (pPrevDCB->pNextDCB != pDCB)
- pPrevDCB = pPrevDCB->pNextDCB;
- pPrevDCB->pNextDCB = pDCB->pNextDCB;
- if (pDCB == pACB->pLastDCB)
- pACB->pLastDCB = pPrevDCB;
- }
-
- if (pDCB == pACB->pActiveDCB)
- pACB->pActiveDCB = NULL;
- if (pDCB == pACB->pLinkDCB)
- pACB->pLinkDCB = pDCB->pNextDCB;
- if (pDCB == pACB->pDCBRunRobin)
- pACB->pDCBRunRobin = pDCB->pNextDCB;
- kfree(pDCB);
-
- pACB->DCBCnt--;
-}
-
-static int dc390_slave_configure(struct scsi_device *sdev)
-{
- struct dc390_acb *acb = (struct dc390_acb *)sdev->host->hostdata;
- struct dc390_dcb *dcb = (struct dc390_dcb *)sdev->hostdata;
-
- acb->scan_devices = 0;
-
- /*
- * XXX: Note that while this driver used to called scsi_activate_tcq,
- * it never actually set a tag type, so emulate the old behavior.
- */
- scsi_set_tag_type(sdev, 0);
-
- if (sdev->tagged_supported && (dcb->DevMode & TAG_QUEUEING_)) {
- dcb->SyncMode |= EN_TAG_QUEUEING;
- scsi_adjust_queue_depth(sdev, acb->TagMaxNum);
- }
-
- return 0;
-}
-
-static struct scsi_host_template driver_template = {
- .module = THIS_MODULE,
- .proc_name = "tmscsim",
- .name = DC390_BANNER " V" DC390_VERSION,
- .slave_alloc = dc390_slave_alloc,
- .slave_configure = dc390_slave_configure,
- .slave_destroy = dc390_slave_destroy,
- .queuecommand = DC390_queuecommand,
- .eh_abort_handler = DC390_abort,
- .eh_bus_reset_handler = DC390_bus_reset,
- .can_queue = 1,
- .this_id = 7,
- .sg_tablesize = SG_ALL,
- .cmd_per_lun = 1,
- .use_clustering = ENABLE_CLUSTERING,
- .max_sectors = 0x4000, /* 8MiB = 16 * 1024 * 512 */
- .use_blk_tags = 1,
-};
-
-/***********************************************************************
- * Functions for access to DC390 EEPROM
- * and some to emulate it
- *
- **********************************************************************/
-
-static void dc390_eeprom_prepare_read(struct pci_dev *pdev, u8 cmd)
-{
- u8 carryFlag = 1, j = 0x80, bval;
- int i;
-
- for (i = 0; i < 9; i++) {
- if (carryFlag) {
- pci_write_config_byte(pdev, 0x80, 0x40);
- bval = 0xc0;
- } else
- bval = 0x80;
-
- udelay(160);
- pci_write_config_byte(pdev, 0x80, bval);
- udelay(160);
- pci_write_config_byte(pdev, 0x80, 0);
- udelay(160);
-
- carryFlag = (cmd & j) ? 1 : 0;
- j >>= 1;
- }
-}
-
-static u16 dc390_eeprom_get_data(struct pci_dev *pdev)
-{
- int i;
- u16 wval = 0;
- u8 bval;
-
- for (i = 0; i < 16; i++) {
- wval <<= 1;
-
- pci_write_config_byte(pdev, 0x80, 0x80);
- udelay(160);
- pci_write_config_byte(pdev, 0x80, 0x40);
- udelay(160);
- pci_read_config_byte(pdev, 0x00, &bval);
-
- if (bval == 0x22)
- wval |= 1;
- }
-
- return wval;
-}
-
-static void dc390_read_eeprom(struct pci_dev *pdev, u16 *ptr)
-{
- u8 cmd = EEPROM_READ, i;
-
- for (i = 0; i < 0x40; i++) {
- pci_write_config_byte(pdev, 0xc0, 0);
- udelay(160);
-
- dc390_eeprom_prepare_read(pdev, cmd++);
- *ptr++ = dc390_eeprom_get_data(pdev);
-
- pci_write_config_byte(pdev, 0x80, 0);
- pci_write_config_byte(pdev, 0x80, 0);
- udelay(160);
- }
-}
-
-/* Override EEprom values with explicitly set values */
-static void dc390_eeprom_override(u8 index)
-{
- u8 *ptr = (u8 *) dc390_eepromBuf[index], id;
-
- /* Adapter Settings */
- if (tmscsim[0] != -2)
- ptr[EE_ADAPT_SCSI_ID] = (u8)tmscsim[0]; /* Adapter ID */
- if (tmscsim[3] != -2)
- ptr[EE_MODE2] = (u8)tmscsim[3];
- if (tmscsim[5] != -2)
- ptr[EE_DELAY] = tmscsim[5]; /* Reset delay */
- if (tmscsim[4] != -2)
- ptr[EE_TAG_CMD_NUM] = (u8)tmscsim[4]; /* Tagged Cmds */
-
- /* Device Settings */
- for (id = 0; id < MAX_SCSI_ID; id++) {
- if (tmscsim[2] != -2)
- ptr[id << 2] = (u8)tmscsim[2]; /* EE_MODE1 */
- if (tmscsim[1] != -2)
- ptr[(id << 2) + 1] = (u8)tmscsim[1]; /* EE_Speed */
- }
-}
-
-static int tmscsim_def[] = {
- 7,
- 0 /* 10MHz */,
- PARITY_CHK_ | SEND_START_ | EN_DISCONNECT_ | SYNC_NEGO_ | TAG_QUEUEING_,
- MORE2_DRV | GREATER_1G | RST_SCSI_BUS | ACTIVE_NEGATION | LUN_CHECK,
- 3 /* 16 Tags per LUN */,
- 1 /* s delay after Reset */,
-};
-
-/* Copy defaults over set values where missing */
-static void dc390_fill_with_defaults (void)
-{
- int i;
-
- for (i = 0; i < 6; i++) {
- if (tmscsim[i] < 0 || tmscsim[i] > 255)
- tmscsim[i] = tmscsim_def[i];
- }
-
- /* Sanity checks */
- if (tmscsim[0] > 7)
- tmscsim[0] = 7;
- if (tmscsim[1] > 7)
- tmscsim[1] = 4;
- if (tmscsim[4] > 5)
- tmscsim[4] = 4;
- if (tmscsim[5] > 180)
- tmscsim[5] = 180;
-}
-
-static void dc390_check_eeprom(struct pci_dev *pdev, u8 index)
-{
- u8 interpd[] = {1, 3, 5, 10, 16, 30, 60, 120};
- u8 EEbuf[128];
- u16 *ptr = (u16 *)EEbuf, wval = 0;
- int i;
-
- dc390_read_eeprom(pdev, ptr);
- memcpy(dc390_eepromBuf[index], EEbuf, EE_ADAPT_SCSI_ID);
- memcpy(&dc390_eepromBuf[index][EE_ADAPT_SCSI_ID],
- &EEbuf[REAL_EE_ADAPT_SCSI_ID], EE_LEN - EE_ADAPT_SCSI_ID);
-
- dc390_eepromBuf[index][EE_DELAY] = interpd[dc390_eepromBuf[index][EE_DELAY]];
-
- for (i = 0; i < 0x40; i++, ptr++)
- wval += *ptr;
-
- /* no Tekram EEprom found */
- if (wval != 0x1234) {
- int speed;
-
- printk(KERN_INFO "DC390_init: No EEPROM found! Trying default settings ...\n");
-
- /*
- * XXX(hch): bogus, because we might have tekram and
- * non-tekram hbas in a single machine.
- */
- dc390_fill_with_defaults();
-
- speed = dc390_clock_speed[tmscsim[1]];
- printk(KERN_INFO "DC390: Used defaults: AdaptID=%i, SpeedIdx=%i (%i.%i MHz), "
- "DevMode=0x%02x, AdaptMode=0x%02x, TaggedCmnds=%i (%i), DelayReset=%is\n",
- tmscsim[0], tmscsim[1], speed / 10, speed % 10,
- (u8)tmscsim[2], (u8)tmscsim[3], tmscsim[4], 2 << (tmscsim[4]), tmscsim[5]);
- }
-}
-
-static void dc390_init_hw(struct dc390_acb *pACB, u8 index)
-{
- struct Scsi_Host *shost = pACB->pScsiHost;
- u8 dstate;
-
- /* Disable SCSI bus reset interrupt */
- DC390_write8(CtrlReg1, DIS_INT_ON_SCSI_RST | shost->this_id);
-
- if (pACB->Gmode2 & RST_SCSI_BUS) {
- dc390_ResetSCSIBus(pACB);
- udelay(1000);
- pACB->last_reset = jiffies + HZ/2 +
- HZ * dc390_eepromBuf[pACB->AdapterIndex][EE_DELAY];
- }
-
- pACB->ACBFlag = 0;
-
- /* Reset Pending INT */
- DC390_read8(INT_Status);
-
- /* 250ms selection timeout */
- DC390_write8(Scsi_TimeOut, SEL_TIMEOUT);
-
- /* Conversion factor = 0 , 40MHz clock */
- DC390_write8(Clk_Factor, CLK_FREQ_40MHZ);
-
- /* NOP cmd - clear command register */
- DC390_write8(ScsiCmd, NOP_CMD);
-
- /* Enable Feature and SCSI-2 */
- DC390_write8(CtrlReg2, EN_FEATURE+EN_SCSI2_CMD);
-
- /* Fast clock */
- DC390_write8(CtrlReg3, FAST_CLK);
-
- /* Negation */
- DC390_write8(CtrlReg4, pACB->glitch_cfg | /* glitch eater */
- (dc390_eepromBuf[index][EE_MODE2] & ACTIVE_NEGATION) ?
- NEGATE_REQACKDATA : 0);
-
- /* Clear Transfer Count High: ID */
- DC390_write8(CtcReg_High, 0);
- DC390_write8(DMA_Cmd, DMA_IDLE_CMD);
- DC390_write8(ScsiCmd, CLEAR_FIFO_CMD);
- DC390_write32(DMA_ScsiBusCtrl, EN_INT_ON_PCI_ABORT);
-
- dstate = DC390_read8(DMA_Status);
- DC390_write8(DMA_Status, dstate);
-}
-
-static int dc390_probe_one(struct pci_dev *pdev, const struct pci_device_id *id)
-{
- struct dc390_acb *pACB;
- struct Scsi_Host *shost;
- unsigned long io_port;
- int error = -ENODEV, i;
-
- if (pci_enable_device(pdev))
- goto out;
-
- pci_set_master(pdev);
-
- error = -ENOMEM;
- if (disable_clustering)
- driver_template.use_clustering = DISABLE_CLUSTERING;
- shost = scsi_host_alloc(&driver_template, sizeof(struct dc390_acb));
- if (!shost)
- goto out_disable_device;
-
- pACB = (struct dc390_acb *)shost->hostdata;
- memset(pACB, 0, sizeof(struct dc390_acb));
-
- dc390_check_eeprom(pdev, dc390_adapterCnt);
- dc390_eeprom_override(dc390_adapterCnt);
-
- io_port = pci_resource_start(pdev, 0);
-
- shost->this_id = dc390_eepromBuf[dc390_adapterCnt][EE_ADAPT_SCSI_ID];
- shost->io_port = io_port;
- shost->n_io_port = 0x80;
- shost->irq = pdev->irq;
- shost->base = io_port;
- shost->unique_id = io_port;
-
- pACB->last_reset = jiffies;
- pACB->pScsiHost = shost;
- pACB->IOPortBase = (u16) io_port;
- pACB->IRQLevel = pdev->irq;
-
- shost->max_id = 8;
-
- if (shost->max_id - 1 ==
- dc390_eepromBuf[dc390_adapterCnt][EE_ADAPT_SCSI_ID])
- shost->max_id--;
-
- if (dc390_eepromBuf[dc390_adapterCnt][EE_MODE2] & LUN_CHECK)
- shost->max_lun = 8;
- else
- shost->max_lun = 1;
-
- pACB->pFreeSRB = pACB->SRB_array;
- pACB->SRBCount = MAX_SRB_CNT;
- pACB->AdapterIndex = dc390_adapterCnt;
- pACB->TagMaxNum =
- 2 << dc390_eepromBuf[dc390_adapterCnt][EE_TAG_CMD_NUM];
- pACB->Gmode2 = dc390_eepromBuf[dc390_adapterCnt][EE_MODE2];
-
- for (i = 0; i < pACB->SRBCount-1; i++)
- pACB->SRB_array[i].pNextSRB = &pACB->SRB_array[i+1];
- pACB->SRB_array[pACB->SRBCount-1].pNextSRB = NULL;
- pACB->pTmpSRB = &pACB->TmpSRB;
-
- pACB->sel_timeout = SEL_TIMEOUT;
- pACB->glitch_cfg = EATER_25NS;
- pACB->pdev = pdev;
-
- if (!request_region(io_port, shost->n_io_port, "tmscsim")) {
- printk(KERN_ERR "DC390: register IO ports error!\n");
- goto out_host_put;
- }
-
- /* Reset Pending INT */
- DC390_read8_(INT_Status, io_port);
-
- if (request_irq(pdev->irq, do_DC390_Interrupt, IRQF_SHARED,
- "tmscsim", pACB)) {
- printk(KERN_ERR "DC390: register IRQ error!\n");
- goto out_release_region;
- }
-
- dc390_init_hw(pACB, dc390_adapterCnt);
-
- dc390_adapterCnt++;
-
- pci_set_drvdata(pdev, shost);
-
- error = scsi_add_host(shost, &pdev->dev);
- if (error)
- goto out_free_irq;
- scsi_scan_host(shost);
- return 0;
-
- out_free_irq:
- free_irq(pdev->irq, pACB);
- out_release_region:
- release_region(io_port, shost->n_io_port);
- out_host_put:
- scsi_host_put(shost);
- out_disable_device:
- pci_disable_device(pdev);
- out:
- return error;
-}
-
-/**
- * dc390_remove_one - Called to remove a single instance of the adapter.
- *
- * @dev: The PCI device to remove.
- */
-static void dc390_remove_one(struct pci_dev *dev)
-{
- struct Scsi_Host *scsi_host = pci_get_drvdata(dev);
- unsigned long iflags;
- struct dc390_acb* pACB = (struct dc390_acb*) scsi_host->hostdata;
- u8 bval;
-
- scsi_remove_host(scsi_host);
-
- spin_lock_irqsave(scsi_host->host_lock, iflags);
- pACB->ACBFlag = RESET_DEV;
- bval = DC390_read8(CtrlReg1) | DIS_INT_ON_SCSI_RST;
- DC390_write8 (CtrlReg1, bval); /* disable interrupt */
- if (pACB->Gmode2 & RST_SCSI_BUS)
- dc390_ResetSCSIBus(pACB);
- spin_unlock_irqrestore(scsi_host->host_lock, iflags);
-
- free_irq(scsi_host->irq, pACB);
- release_region(scsi_host->io_port, scsi_host->n_io_port);
-
- pci_disable_device(dev);
- scsi_host_put(scsi_host);
-}
-
-static struct pci_device_id tmscsim_pci_tbl[] = {
- { PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD53C974,
- PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
- { }
-};
-MODULE_DEVICE_TABLE(pci, tmscsim_pci_tbl);
-
-static struct pci_driver dc390_driver = {
- .name = "tmscsim",
- .id_table = tmscsim_pci_tbl,
- .probe = dc390_probe_one,
- .remove = dc390_remove_one,
-};
-
-static int __init dc390_module_init(void)
-{
- if (!disable_clustering) {
- printk(KERN_INFO "DC390: clustering now enabled by default. If you get problems load\n");
- printk(KERN_INFO " with \"disable_clustering=1\" and report to maintainers\n");
- }
-
- if (tmscsim[0] == -1 || tmscsim[0] > 15) {
- tmscsim[0] = 7;
- tmscsim[1] = 4;
- tmscsim[2] = PARITY_CHK_ | TAG_QUEUEING_;
- tmscsim[3] = MORE2_DRV | GREATER_1G | RST_SCSI_BUS | ACTIVE_NEGATION;
- tmscsim[4] = 2;
- tmscsim[5] = 10;
- printk (KERN_INFO "DC390: Using safe settings.\n");
- }
-
- return pci_register_driver(&dc390_driver);
-}
-
-static void __exit dc390_module_exit(void)
-{
- pci_unregister_driver(&dc390_driver);
-}
-
-module_init(dc390_module_init);
-module_exit(dc390_module_exit);
-
-#ifndef MODULE
-static int __init dc390_setup (char *str)
-{
- int ints[8],i, im;
-
- get_options(str, ARRAY_SIZE(ints), ints);
- im = ints[0];
-
- if (im > 6) {
- printk (KERN_NOTICE "DC390: ignore extra params!\n");
- im = 6;
- }
-
- for (i = 0; i < im; i++)
- tmscsim[i] = ints[i+1];
- /* dc390_checkparams (); */
- return 1;
-}
-
-__setup("tmscsim=", dc390_setup);
-#endif
diff --git a/drivers/scsi/tmscsim.h b/drivers/scsi/tmscsim.h
deleted file mode 100644
index c9ad4bb..0000000
--- a/drivers/scsi/tmscsim.h
+++ /dev/null
@@ -1,549 +0,0 @@
-/***********************************************************************
-;* File Name : TMSCSIM.H *
-;* TEKRAM DC-390(T) PCI SCSI Bus Master Host Adapter *
-;* Device Driver *
-;***********************************************************************/
-/* $Id: tmscsim.h,v 2.15.2.3 2000/11/17 20:52:27 garloff Exp $ */
-
-#ifndef _TMSCSIM_H
-#define _TMSCSIM_H
-
-#include <linux/types.h>
-
-#define MAX_ADAPTER_NUM 4
-#define MAX_SG_LIST_BUF 16 /* Not used */
-#define MAX_SCSI_ID 8
-#define MAX_SRB_CNT 50 /* Max number of started commands */
-
-#define SEL_TIMEOUT 153 /* 250 ms selection timeout (@ 40 MHz) */
-
-/*
-;-----------------------------------------------------------------------
-; SCSI Request Block
-;-----------------------------------------------------------------------
-*/
-struct dc390_srb
-{
-//u8 CmdBlock[12];
-
-struct dc390_srb *pNextSRB;
-struct dc390_dcb *pSRBDCB;
-struct scsi_cmnd *pcmd;
-struct scatterlist *pSegmentList;
-
-struct scatterlist Segmentx; /* make a one entry of S/G list table */
-
-unsigned long SGBusAddr; /*;a segment starting address as seen by AM53C974A
- in CPU endianness. We're only getting 32-bit bus
- addresses by default */
-unsigned long SGToBeXferLen; /*; to be xfer length */
-unsigned long TotalXferredLen;
-unsigned long SavedTotXLen;
-unsigned long Saved_Ptr;
-u32 SRBState;
-
-u8 SRBStatus;
-u8 SRBFlag; /*; b0-AutoReqSense,b6-Read,b7-write */
- /*; b4-settimeout,b5-Residual valid */
-u8 AdaptStatus;
-u8 TargetStatus;
-
-u8 ScsiPhase;
-s8 TagNumber;
-u8 SGIndex;
-u8 SGcount;
-
-u8 MsgCnt;
-u8 EndMessage;
-
-u8 MsgInBuf[6];
-u8 MsgOutBuf[6];
-
-//u8 IORBFlag; /*;81h-Reset, 2-retry */
-};
-
-
-/*
-;-----------------------------------------------------------------------
-; Device Control Block
-;-----------------------------------------------------------------------
-*/
-struct dc390_dcb
-{
-struct dc390_dcb *pNextDCB;
-struct dc390_acb *pDCBACB;
-
-/* Queued SRBs */
-struct dc390_srb *pGoingSRB;
-struct dc390_srb *pGoingLast;
-struct dc390_srb *pActiveSRB;
-u8 GoingSRBCnt;
-
-u32 TagMask;
-
-u8 TargetID; /*; SCSI Target ID (SCSI Only) */
-u8 TargetLUN; /*; SCSI Log. Unit (SCSI Only) */
-u8 DevMode;
-u8 DCBFlag;
-
-u8 CtrlR1;
-u8 CtrlR3;
-u8 CtrlR4;
-
-u8 SyncMode; /*; 0:async mode */
-u8 NegoPeriod; /*;for nego. */
-u8 SyncPeriod; /*;for reg. */
-u8 SyncOffset; /*;for reg. and nego.(low nibble) */
-};
-
-
-/*
-;-----------------------------------------------------------------------
-; Adapter Control Block
-;-----------------------------------------------------------------------
-*/
-struct dc390_acb
-{
-struct Scsi_Host *pScsiHost;
-u16 IOPortBase;
-u8 IRQLevel;
-u8 status;
-
-u8 SRBCount;
-u8 AdapterIndex; /*; nth Adapter this driver */
-u8 DCBCnt;
-
-u8 TagMaxNum;
-u8 ACBFlag;
-u8 Gmode2;
-u8 scan_devices;
-
-struct dc390_dcb *pLinkDCB;
-struct dc390_dcb *pLastDCB;
-struct dc390_dcb *pDCBRunRobin;
-
-struct dc390_dcb *pActiveDCB;
-struct dc390_srb *pFreeSRB;
-struct dc390_srb *pTmpSRB;
-
-u8 msgin123[4];
-u8 Connected;
-u8 pad;
-
-#if defined(USE_SPINLOCKS) && USE_SPINLOCKS > 1 && (defined(CONFIG_SMP) || DEBUG_SPINLOCKS > 0)
-spinlock_t lock;
-#endif
-u8 sel_timeout;
-u8 glitch_cfg;
-
-u8 MsgLen;
-u8 Ignore_IRQ; /* Not used */
-
-struct pci_dev *pdev;
-
-unsigned long last_reset;
-unsigned long Cmds;
-u32 SelLost;
-u32 SelConn;
-u32 CmdInQ;
-u32 CmdOutOfSRB;
-
-struct dc390_srb TmpSRB;
-struct dc390_srb SRB_array[MAX_SRB_CNT]; /* 50 SRBs */
-};
-
-
-/*;-----------------------------------------------------------------------*/
-
-
-#define BIT31 0x80000000
-#define BIT30 0x40000000
-#define BIT29 0x20000000
-#define BIT28 0x10000000
-#define BIT27 0x08000000
-#define BIT26 0x04000000
-#define BIT25 0x02000000
-#define BIT24 0x01000000
-#define BIT23 0x00800000
-#define BIT22 0x00400000
-#define BIT21 0x00200000
-#define BIT20 0x00100000
-#define BIT19 0x00080000
-#define BIT18 0x00040000
-#define BIT17 0x00020000
-#define BIT16 0x00010000
-#define BIT15 0x00008000
-#define BIT14 0x00004000
-#define BIT13 0x00002000
-#define BIT12 0x00001000
-#define BIT11 0x00000800
-#define BIT10 0x00000400
-#define BIT9 0x00000200
-#define BIT8 0x00000100
-#define BIT7 0x00000080
-#define BIT6 0x00000040
-#define BIT5 0x00000020
-#define BIT4 0x00000010
-#define BIT3 0x00000008
-#define BIT2 0x00000004
-#define BIT1 0x00000002
-#define BIT0 0x00000001
-
-/*;---UnitCtrlFlag */
-#define UNIT_ALLOCATED BIT0
-#define UNIT_INFO_CHANGED BIT1
-#define FORMATING_MEDIA BIT2
-#define UNIT_RETRY BIT3
-
-/*;---UnitFlags */
-#define DASD_SUPPORT BIT0
-#define SCSI_SUPPORT BIT1
-#define ASPI_SUPPORT BIT2
-
-/*;----SRBState machine definition */
-#define SRB_FREE 0
-#define SRB_WAIT BIT0
-#define SRB_READY BIT1
-#define SRB_MSGOUT BIT2 /*;arbitration+msg_out 1st byte*/
-#define SRB_MSGIN BIT3
-#define SRB_MSGIN_MULTI BIT4
-#define SRB_COMMAND BIT5
-#define SRB_START_ BIT6 /*;arbitration+msg_out+command_out*/
-#define SRB_DISCONNECT BIT7
-#define SRB_DATA_XFER BIT8
-#define SRB_XFERPAD BIT9
-#define SRB_STATUS BIT10
-#define SRB_COMPLETED BIT11
-#define SRB_ABORT_SENT BIT12
-#define DO_SYNC_NEGO BIT13
-#define SRB_UNEXPECT_RESEL BIT14
-
-/*;---SRBstatus */
-#define SRB_OK BIT0
-#define ABORTION BIT1
-#define OVER_RUN BIT2
-#define UNDER_RUN BIT3
-#define PARITY_ERROR BIT4
-#define SRB_ERROR BIT5
-
-/*;---ACBFlag */
-#define RESET_DEV BIT0
-#define RESET_DETECT BIT1
-#define RESET_DONE BIT2
-
-/*;---DCBFlag */
-#define ABORT_DEV_ BIT0
-
-/*;---SRBFlag */
-#define DATAOUT BIT7
-#define DATAIN BIT6
-#define RESIDUAL_VALID BIT5
-#define ENABLE_TIMER BIT4
-#define RESET_DEV0 BIT2
-#define ABORT_DEV BIT1
-#define AUTO_REQSENSE BIT0
-
-/*;---Adapter status */
-#define H_STATUS_GOOD 0
-#define H_SEL_TIMEOUT 0x11
-#define H_OVER_UNDER_RUN 0x12
-#define H_UNEXP_BUS_FREE 0x13
-#define H_TARGET_PHASE_F 0x14
-#define H_INVALID_CCB_OP 0x16
-#define H_LINK_CCB_BAD 0x17
-#define H_BAD_TARGET_DIR 0x18
-#define H_DUPLICATE_CCB 0x19
-#define H_BAD_CCB_OR_SG 0x1A
-#define H_ABORT 0x0FF
-
-/* cmd->result */
-#define RES_TARGET 0x000000FF /* Target State */
-#define RES_TARGET_LNX STATUS_MASK /* Only official ... */
-#define RES_ENDMSG 0x0000FF00 /* End Message */
-#define RES_DID 0x00FF0000 /* DID_ codes */
-#define RES_DRV 0xFF000000 /* DRIVER_ codes */
-
-#define MK_RES(drv,did,msg,tgt) ((int)(drv)<<24 | (int)(did)<<16 | (int)(msg)<<8 | (int)(tgt))
-#define MK_RES_LNX(drv,did,msg,tgt) ((int)(drv)<<24 | (int)(did)<<16 | (int)(msg)<<8 | (int)(tgt))
-
-#define SET_RES_TARGET(who, tgt) do { who &= ~RES_TARGET; who |= (int)(tgt); } while (0)
-#define SET_RES_TARGET_LNX(who, tgt) do { who &= ~RES_TARGET_LNX; who |= (int)(tgt) << 1; } while (0)
-#define SET_RES_MSG(who, msg) do { who &= ~RES_ENDMSG; who |= (int)(msg) << 8; } while (0)
-#define SET_RES_DID(who, did) do { who &= ~RES_DID; who |= (int)(did) << 16; } while (0)
-#define SET_RES_DRV(who, drv) do { who &= ~RES_DRV; who |= (int)(drv) << 24; } while (0)
-
-/*;---Sync_Mode */
-#define SYNC_DISABLE 0
-#define SYNC_ENABLE BIT0
-#define SYNC_NEGO_DONE BIT1
-#define WIDE_ENABLE BIT2 /* Not used ;-) */
-#define WIDE_NEGO_DONE BIT3 /* Not used ;-) */
-#define EN_TAG_QUEUEING BIT4
-#define EN_ATN_STOP BIT5
-
-#define SYNC_NEGO_OFFSET 15
-
-/*;---SCSI bus phase*/
-#define SCSI_DATA_OUT 0
-#define SCSI_DATA_IN 1
-#define SCSI_COMMAND 2
-#define SCSI_STATUS_ 3
-#define SCSI_NOP0 4
-#define SCSI_NOP1 5
-#define SCSI_MSG_OUT 6
-#define SCSI_MSG_IN 7
-
-/*;----SCSI MSG BYTE*/ /* see scsi/scsi.h */ /* One is missing ! */
-#define ABORT_TAG 0x0d
-
-/*
- * SISC query queue
- */
-typedef struct {
- dma_addr_t saved_dma_handle;
-} dc390_cmd_scp_t;
-
-/*
-;==========================================================
-; EEPROM byte offset
-;==========================================================
-*/
-typedef struct _EEprom
-{
-u8 EE_MODE1;
-u8 EE_SPEED;
-u8 xx1;
-u8 xx2;
-} EEprom, *PEEprom;
-
-#define REAL_EE_ADAPT_SCSI_ID 64
-#define REAL_EE_MODE2 65
-#define REAL_EE_DELAY 66
-#define REAL_EE_TAG_CMD_NUM 67
-
-#define EE_ADAPT_SCSI_ID 32
-#define EE_MODE2 33
-#define EE_DELAY 34
-#define EE_TAG_CMD_NUM 35
-
-#define EE_LEN 40
-
-/*; EE_MODE1 bits definition*/
-#define PARITY_CHK_ BIT0
-#define SYNC_NEGO_ BIT1
-#define EN_DISCONNECT_ BIT2
-#define SEND_START_ BIT3
-#define TAG_QUEUEING_ BIT4
-
-/*; EE_MODE2 bits definition*/
-#define MORE2_DRV BIT0
-#define GREATER_1G BIT1
-#define RST_SCSI_BUS BIT2
-#define ACTIVE_NEGATION BIT3
-#define NO_SEEK BIT4
-#define LUN_CHECK BIT5
-
-#define ENABLE_CE 1
-#define DISABLE_CE 0
-#define EEPROM_READ 0x80
-
-/*
-;==========================================================
-; AMD 53C974 Registers bit Definition
-;==========================================================
-*/
-/*
-;====================
-; SCSI Register
-;====================
-*/
-
-/*; Command Reg.(+0CH) (rw) */
-#define DMA_COMMAND BIT7
-#define NOP_CMD 0
-#define CLEAR_FIFO_CMD 1
-#define RST_DEVICE_CMD 2
-#define RST_SCSI_BUS_CMD 3
-
-#define INFO_XFER_CMD 0x10
-#define INITIATOR_CMD_CMPLTE 0x11
-#define MSG_ACCEPTED_CMD 0x12
-#define XFER_PAD_BYTE 0x18
-#define SET_ATN_CMD 0x1A
-#define RESET_ATN_CMD 0x1B
-
-#define SEL_WO_ATN 0x41 /* currently not used */
-#define SEL_W_ATN 0x42
-#define SEL_W_ATN_STOP 0x43
-#define SEL_W_ATN3 0x46
-#define EN_SEL_RESEL 0x44
-#define DIS_SEL_RESEL 0x45 /* currently not used */
-#define RESEL 0x40 /* " */
-#define RESEL_ATN3 0x47 /* " */
-
-#define DATA_XFER_CMD INFO_XFER_CMD
-
-
-/*; SCSI Status Reg.(+10H) (r) */
-#define INTERRUPT BIT7
-#define ILLEGAL_OP_ERR BIT6
-#define PARITY_ERR BIT5
-#define COUNT_2_ZERO BIT4
-#define GROUP_CODE_VALID BIT3
-#define SCSI_PHASE_MASK (BIT2+BIT1+BIT0)
-/* BIT2: MSG phase; BIT1: C/D physe; BIT0: I/O phase */
-
-/*; Interrupt Status Reg.(+14H) (r) */
-#define SCSI_RESET BIT7
-#define INVALID_CMD BIT6
-#define DISCONNECTED BIT5
-#define SERVICE_REQUEST BIT4
-#define SUCCESSFUL_OP BIT3
-#define RESELECTED BIT2
-#define SEL_ATTENTION BIT1
-#define SELECTED BIT0
-
-/*; Internal State Reg.(+18H) (r) */
-#define SYNC_OFFSET_FLAG BIT3
-#define INTRN_STATE_MASK (BIT2+BIT1+BIT0)
-/* 0x04: Sel. successful (w/o stop), 0x01: Sel. successful (w/ stop) */
-
-/*; Clock Factor Reg.(+24H) (w) */
-#define CLK_FREQ_40MHZ 0
-#define CLK_FREQ_35MHZ (BIT2+BIT1+BIT0)
-#define CLK_FREQ_30MHZ (BIT2+BIT1)
-#define CLK_FREQ_25MHZ (BIT2+BIT0)
-#define CLK_FREQ_20MHZ BIT2
-#define CLK_FREQ_15MHZ (BIT1+BIT0)
-#define CLK_FREQ_10MHZ BIT1
-
-/*; Control Reg. 1(+20H) (rw) */
-#define EXTENDED_TIMING BIT7
-#define DIS_INT_ON_SCSI_RST BIT6
-#define PARITY_ERR_REPO BIT4
-#define SCSI_ID_ON_BUS (BIT2+BIT1+BIT0) /* host adapter ID */
-
-/*; Control Reg. 2(+2CH) (rw) */
-#define EN_FEATURE BIT6
-#define EN_SCSI2_CMD BIT3
-
-/*; Control Reg. 3(+30H) (rw) */
-#define ID_MSG_CHECK BIT7
-#define EN_QTAG_MSG BIT6
-#define EN_GRP2_CMD BIT5
-#define FAST_SCSI BIT4 /* ;10MB/SEC */
-#define FAST_CLK BIT3 /* ;25 - 40 MHZ */
-
-/*; Control Reg. 4(+34H) (rw) */
-#define EATER_12NS 0
-#define EATER_25NS BIT7
-#define EATER_35NS BIT6
-#define EATER_0NS (BIT7+BIT6)
-#define REDUCED_POWER BIT5
-#define CTRL4_RESERVED BIT4 /* must be 1 acc. to AM53C974.c */
-#define NEGATE_REQACKDATA BIT2
-#define NEGATE_REQACK BIT3
-
-#define GLITCH_TO_NS(x) (((~x>>6 & 2) >> 1) | ((x>>6 & 1) << 1 ^ (x>>6 & 2)))
-#define NS_TO_GLITCH(y) (((~y<<7) | ~((y<<6) ^ ((y<<5 & 1<<6) | ~0x40))) & 0xc0)
-
-/*
-;====================
-; DMA Register
-;====================
-*/
-/*; DMA Command Reg.(+40H) (rw) */
-#define READ_DIRECTION BIT7
-#define WRITE_DIRECTION 0
-#define EN_DMA_INT BIT6
-#define EN_PAGE_INT BIT5 /* page transfer interrupt enable */
-#define MAP_TO_MDL BIT4
-#define DIAGNOSTIC BIT2
-#define DMA_IDLE_CMD 0
-#define DMA_BLAST_CMD BIT0
-#define DMA_ABORT_CMD BIT1
-#define DMA_START_CMD (BIT1+BIT0)
-
-/*; DMA Status Reg.(+54H) (r) */
-#define PCI_MS_ABORT BIT6
-#define BLAST_COMPLETE BIT5
-#define SCSI_INTERRUPT BIT4
-#define DMA_XFER_DONE BIT3
-#define DMA_XFER_ABORT BIT2
-#define DMA_XFER_ERROR BIT1
-#define POWER_DOWN BIT0
-
-/*; DMA SCSI Bus and Ctrl.(+70H) */
-#define EN_INT_ON_PCI_ABORT BIT25
-#define WRT_ERASE_DMA_STAT BIT24
-#define PW_DOWN_CTRL BIT21
-#define SCSI_BUSY BIT20
-#define SCLK BIT19
-#define SCAM BIT18
-#define SCSI_LINES 0x0003ffff
-
-/*
-;==========================================================
-; SCSI Chip register address offset
-;==========================================================
-;Registers are rw unless declared otherwise
-*/
-#define CtcReg_Low 0x00 /* r curr. transfer count */
-#define CtcReg_Mid 0x04 /* r */
-#define CtcReg_High 0x38 /* r */
-#define ScsiFifo 0x08
-#define ScsiCmd 0x0C
-#define Scsi_Status 0x10 /* r */
-#define INT_Status 0x14 /* r */
-#define Sync_Period 0x18 /* w */
-#define Sync_Offset 0x1C /* w */
-#define Clk_Factor 0x24 /* w */
-#define CtrlReg1 0x20
-#define CtrlReg2 0x2C
-#define CtrlReg3 0x30
-#define CtrlReg4 0x34
-#define DMA_Cmd 0x40
-#define DMA_XferCnt 0x44 /* rw starting transfer count (32 bit) */
-#define DMA_XferAddr 0x48 /* rw starting physical address (32 bit) */
-#define DMA_Wk_ByteCntr 0x4C /* r working byte counter */
-#define DMA_Wk_AddrCntr 0x50 /* r working address counter */
-#define DMA_Status 0x54 /* r */
-#define DMA_MDL_Addr 0x58 /* rw starting MDL address */
-#define DMA_Wk_MDL_Cntr 0x5C /* r working MDL counter */
-#define DMA_ScsiBusCtrl 0x70 /* rw SCSI Bus, PCI/DMA Ctrl */
-
-#define StcReg_Low CtcReg_Low /* w start transfer count */
-#define StcReg_Mid CtcReg_Mid /* w */
-#define StcReg_High CtcReg_High /* w */
-#define Scsi_Dest_ID Scsi_Status /* w */
-#define Scsi_TimeOut INT_Status /* w */
-#define Intern_State Sync_Period /* r */
-#define Current_Fifo Sync_Offset /* r Curr. FIFO / int. state */
-
-
-#define DC390_read8(address) \
- (inb (pACB->IOPortBase + (address)))
-
-#define DC390_read8_(address, base) \
- (inb ((u16)(base) + (address)))
-
-#define DC390_read16(address) \
- (inw (pACB->IOPortBase + (address)))
-
-#define DC390_read32(address) \
- (inl (pACB->IOPortBase + (address)))
-
-#define DC390_write8(address,value) \
- outb ((value), pACB->IOPortBase + (address))
-
-#define DC390_write8_(address,value,base) \
- outb ((value), (u16)(base) + (address))
-
-#define DC390_write16(address,value) \
- outw ((value), pACB->IOPortBase + (address))
-
-#define DC390_write32(address,value) \
- outl ((value), pACB->IOPortBase + (address))
-
-
-#endif /* _TMSCSIM_H */
--
1.8.5.2
next prev parent reply other threads:[~2014-11-24 14:37 UTC|newest]
Thread overview: 17+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-11-24 14:37 [PATCHv3 00/12] Re-implement am53c974 driver Hannes Reinecke
2014-11-24 14:37 ` [PATCH 01/12] esp_scsi: spellcheck 'driver' Hannes Reinecke
2014-11-24 14:37 ` [PATCH 02/12] esp_scsi: make number of tags configurable Hannes Reinecke
2014-11-24 14:37 ` [PATCH 03/12] esp_scsi: convert to dev_printk Hannes Reinecke
2014-11-24 14:37 ` [PATCH 04/12] esp_scsi: debug event and command Hannes Reinecke
2014-11-24 14:37 ` [PATCH 05/12] esp_scsi: read status registers Hannes Reinecke
2014-11-24 14:37 ` [PATCH 06/12] esp_scsi: use FIFO for command submission Hannes Reinecke
2014-11-24 14:37 ` [PATCH 07/12] scsi: add 'am53c974' driver Hannes Reinecke
2014-11-24 14:37 ` [PATCH 08/12] am53c974: BLAST residual handling Hannes Reinecke
2014-11-24 14:37 ` [PATCH 09/12] esp: correctly detect am53c974 Hannes Reinecke
2014-11-24 14:37 ` [PATCH 10/12] esp_scsi: let DMA driver provide a config2 value Hannes Reinecke
2014-11-24 14:37 ` [PATCH 11/12] esp: enable CONFIG2_FENAB for am53c974 Hannes Reinecke
2014-11-24 14:37 ` Hannes Reinecke [this message]
2014-11-24 15:18 ` [PATCHv3 00/12] Re-implement am53c974 driver Christoph Hellwig
-- strict thread matches above, loose matches on Subject: below --
2014-11-21 12:41 [PATCHv2 " Hannes Reinecke
2014-11-21 12:41 ` [PATCH 12/12] Replace tmscsim by am53c974 Hannes Reinecke
2014-11-23 13:22 ` Guennadi Liakhovetski
2014-11-23 18:45 ` David Miller
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1416839850-30475-13-git-send-email-hare@suse.de \
--to=hare@suse.de \
--cc="Bonzini <pbonzini"@redhat.com \
--cc=Paolo@suse.de \
--cc=davem@davemloft.net \
--cc=hch@lst.de \
--cc=jbottomley@parallels.com \
--cc=linux-scsi@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.