[Qemu-devel] [PATCH 3/8] fdc: Introduce fdctrl->phase

[Kevin Wolf <kwolf@redhat.com>]

The floppy controller spec describes three different controller phases,
which are currently not explicitly modelled in our emulation. Instead,
each phase is represented by a combination of flags in registers.

This patch makes explicit in which phase the controller currently is.

Signed-off-by: Kevin Wolf <kwolf@redhat.com>
---
 hw/block/fdc.c | 31 +++++++++++++++++++++++++++++++
 1 file changed, 31 insertions(+)

diff --git a/hw/block/fdc.c b/hw/block/fdc.c
index 8c41434..4d4868e 100644
--- a/hw/block/fdc.c
+++ b/hw/block/fdc.c
@@ -495,6 +495,30 @@ enum {
     FD_DIR_DSKCHG   = 0x80,
 };
 
+/*
+ * See chapter 5.0 "Controller phases" of the spec:
+ *
+ * Command phase:
+ * The host writes a command and its parameters into the FIFO. The command
+ * phase is completed when all parameters for the command have been supplied,
+ * and execution phase is entered.
+ *
+ * Execution phase:
+ * Data transfers, either DMA or non-DMA. For non-DMA transfers, the FIFO
+ * contains the payload now, otherwise it's unused. When all bytes of the
+ * required data have been transferred, the state is switched to either result
+ * phase (if the command produces status bytes) or directly back into the
+ * command phase for the next command.
+ *
+ * Result phase:
+ * The host reads out the FIFO, which contains one or more result bytes now.
+ */
+typedef enum FDCtrlPhase {
+    FD_PHASE_COMMAND,
+    FD_PHASE_EXECUTION,
+    FD_PHASE_RESULT,
+} FDCtrlPhase;
+
 #define FD_MULTI_TRACK(state) ((state) & FD_STATE_MULTI)
 #define FD_FORMAT_CMD(state) ((state) & FD_STATE_FORMAT)
 
@@ -504,6 +528,7 @@ struct FDCtrl {
     /* Controller state */
     QEMUTimer *result_timer;
     int dma_chann;
+    FDCtrlPhase phase;
     /* Controller's identification */
     uint8_t version;
     /* HW */
@@ -1137,6 +1162,7 @@ static uint32_t fdctrl_read_dir(FDCtrl *fdctrl)
 /* Clear the FIFO and update the state for receiving the next command */
 static void fdctrl_to_command_phase(FDCtrl *fdctrl)
 {
+    fdctrl->phase = FD_PHASE_COMMAND;
     fdctrl->data_dir = FD_DIR_WRITE;
     fdctrl->data_pos = 0;
     fdctrl->msr &= ~(FD_MSR_CMDBUSY | FD_MSR_DIO);
@@ -1146,6 +1172,7 @@ static void fdctrl_to_command_phase(FDCtrl *fdctrl)
  * @fifo_len is the number of result bytes to be read out. */
 static void fdctrl_to_result_phase(FDCtrl *fdctrl, int fifo_len)
 {
+    fdctrl->phase = FD_PHASE_RESULT;
     fdctrl->data_dir = FD_DIR_READ;
     fdctrl->data_len = fifo_len;
     fdctrl->data_pos = 0;
@@ -1912,6 +1939,9 @@ static void fdctrl_handle_relative_seek_out(FDCtrl *fdctrl, int direction)
     fdctrl_raise_irq(fdctrl);
 }
 
+/*
+ * Handlers for the execution phase of each command
+ */
 static const struct {
     uint8_t value;
     uint8_t mask;
@@ -2015,6 +2045,7 @@ static void fdctrl_write_data(FDCtrl *fdctrl, uint32_t value)
         /* We now have all parameters
          * and will be able to treat the command
          */
+        fdctrl->phase = FD_PHASE_EXECUTION;
         if (fdctrl->data_state & FD_STATE_FORMAT) {
             fdctrl_format_sector(fdctrl);
             return;
-- 
1.8.3.1