[linux-sunxi] [PATCH v3 2/2] phy-sun4i-usb: Add support for the host usb-phys found on the H3 SoC

[plaes@plaes.org (Priit Laes)]

On Wed, 2015-11-25 at 17:50 +0100, Hans de Goede wrote:
> From: Reinder de Haan <patchesrdh@mveas.com>
> 
> Note this commit only adds support for phys 1-3, phy 0, the otg phy,
> is
> not yet (fully) supported after this commit.
> 
> Signed-off-by: Reinder de Haan <patchesrdh@mveas.com>
> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
> ---
> Changes in v2:
> -Change break; after dev_err() to return, as intended, fixing a
> compiler
> ?warning (the dev_err case should never be reached)
> Changes in v3:
> -Use of_match_node to get model specific config data
> ---
> ?.../devicetree/bindings/phy/sun4i-usb-phy.txt??????|??1 +
> ?drivers/phy/phy-sun4i-usb.c????????????????????????| 46
> +++++++++++++++++-----
> ?2 files changed, 38 insertions(+), 9 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt
> b/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt
> index 0cebf74..95736d7 100644
> --- a/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt
> +++ b/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt
> @@ -9,6 +9,7 @@ Required properties:
> ???* allwinner,sun7i-a20-usb-phy
> ???* allwinner,sun8i-a23-usb-phy
> ???* allwinner,sun8i-a33-usb-phy
> +??* allwinner,sun8i-h3-usb-phy
> ?- reg : a list of offset + length pairs
> ?- reg-names :
> ???* "phy_ctrl"
> diff --git a/drivers/phy/phy-sun4i-usb.c b/drivers/phy/phy-sun4i-
> usb.c
> index 1d8f85d..2aed482 100644
> --- a/drivers/phy/phy-sun4i-usb.c
> +++ b/drivers/phy/phy-sun4i-usb.c
> @@ -46,6 +46,9 @@
> ?#define REG_PHYBIST			0x08
> ?#define REG_PHYTUNE			0x0c
> ?#define REG_PHYCTL_A33			0x10
> +#define REG_PHY_UNK_H3			0x20
> +
> +#define REG_PMU_UNK_H3			0x10
> ?
> ?#define PHYCTL_DATA			BIT(7)
> ?
> @@ -79,7 +82,7 @@
> ?#define PHY_DISCON_TH_SEL		0x2a
> ?#define PHY_SQUELCH_DETECT		0x3c
> ?
> -#define MAX_PHYS			3
> +#define MAX_PHYS			4
> ?
> ?/*
> ? * Note do not raise the debounce time, we must report Vusb high
> within 100ms
> @@ -91,6 +94,7 @@
> ?enum sun4i_usb_phy_type {
> ?	sun4i_a10_phy,
> ?	sun8i_a33_phy,
> +	sun8i_h3_phy,
> ?};
> ?
> ?struct sun4i_usb_phy_cfg {
> @@ -101,6 +105,7 @@ struct sun4i_usb_phy_cfg {
> ?};
> ?
> ?struct sun4i_usb_phy_data {
> +	struct device *dev;
> ?	void __iomem *base;
> ?	const struct sun4i_usb_phy_cfg *cfg;
> ?	struct mutex mutex;
> @@ -183,6 +188,9 @@ static void sun4i_usb_phy_write(struct
> sun4i_usb_phy *phy, u32 addr, u32 data,
> ?		/* A33 needs us to set phyctl to 0 explicitly */
> ?		writel(0, phyctl);
> ?		break;
> +	case sun8i_h3_phy:
> +		dev_err(phy_data->dev, "H3 usb_phy_write is not
> supported\n");

You should unlock the mutex here.

> +		return;

Also, it might make sense to add default case what WARN's on invalid
enum.

> ?	}
> ?
> ?	for (i = 0; i < len; i++) {
> @@ -243,6 +251,7 @@ static int sun4i_usb_phy_init(struct phy *_phy)
> ?	struct sun4i_usb_phy *phy = phy_get_drvdata(_phy);
> ?	struct sun4i_usb_phy_data *data =
> to_sun4i_usb_phy_data(phy);
> ?	int ret;
> +	u32 val;
> ?
> ?	ret = clk_prepare_enable(phy->clk);
> ?	if (ret)
> @@ -254,16 +263,26 @@ static int sun4i_usb_phy_init(struct phy *_phy)
> ?		return ret;
> ?	}
> ?
> -	/* Enable USB 45 Ohm resistor calibration */
> -	if (phy->index == 0)
> -		sun4i_usb_phy_write(phy, PHY_RES45_CAL_EN, 0x01, 1);
> +	if (data->cfg->type == sun8i_h3_phy) {
> +		if (phy->index == 0) {
> +			val = readl(data->base + REG_PHY_UNK_H3);
> +			writel(val & ~1, data->base +
> REG_PHY_UNK_H3);
> +		}
> ?
> -	/* Adjust PHY's magnitude and rate */
> -	sun4i_usb_phy_write(phy, PHY_TX_AMPLITUDE_TUNE, 0x14, 5);
> +		val = readl(phy->pmu + REG_PMU_UNK_H3);
> +		writel(val & ~2, phy->pmu + REG_PMU_UNK_H3);
> +	} else {
> +		/* Enable USB 45 Ohm resistor calibration */
> +		if (phy->index == 0)
> +			sun4i_usb_phy_write(phy, PHY_RES45_CAL_EN,
> 0x01, 1);
> ?
> -	/* Disconnect threshold adjustment */
> -	sun4i_usb_phy_write(phy, PHY_DISCON_TH_SEL,
> -			????data->cfg->disc_thresh, 2);
> +		/* Adjust PHY's magnitude and rate */
> +		sun4i_usb_phy_write(phy, PHY_TX_AMPLITUDE_TUNE,
> 0x14, 5);
> +
> +		/* Disconnect threshold adjustment */
> +		sun4i_usb_phy_write(phy, PHY_DISCON_TH_SEL,
> +				????data->cfg->disc_thresh, 2);
> +	}
> ?
> ?	sun4i_usb_phy_passby(phy, 1);
> ?
> @@ -555,6 +574,13 @@ static const struct sun4i_usb_phy_cfg
> sun8i_a33_cfg = {
> ?	.dedicated_clocks = true,
> ?};
> ?
> +static const struct sun4i_usb_phy_cfg sun8i_h3_cfg = {
> +	.num_phys = 4,
> +	.disc_thresh = 3,
> +	.type = sun8i_h3_phy,
> +	.dedicated_clocks = true,
> +};
> +
> ?static const struct of_device_id sun4i_usb_phy_of_match[] = {
> ?	{ .compatible = "allwinner,sun4i-a10-usb-phy", .data =
> &sun4i_a10_cfg },
> ?	{ .compatible = "allwinner,sun5i-a13-usb-phy", .data =
> &sun5i_a13_cfg },
> @@ -562,6 +588,7 @@ static const struct of_device_id
> sun4i_usb_phy_of_match[] = {
> ?	{ .compatible = "allwinner,sun7i-a20-usb-phy", .data =
> &sun7i_a20_cfg },
> ?	{ .compatible = "allwinner,sun8i-a23-usb-phy", .data =
> &sun8i_a23_cfg },
> ?	{ .compatible = "allwinner,sun8i-a33-usb-phy", .data =
> &sun8i_a33_cfg },
> +	{ .compatible = "allwinner,sun8i-h3-usb-phy", .data =
> &sun8i_h3_cfg },
> ?	{ },
> ?};
> ?MODULE_DEVICE_TABLE(of, sun4i_usb_phy_of_match);
> @@ -595,6 +622,7 @@ static int sun4i_usb_phy_probe(struct
> platform_device *pdev)
> ?	mutex_init(&data->mutex);
> ?	INIT_DELAYED_WORK(&data->detect,
> sun4i_usb_phy0_id_vbus_det_scan);
> ?	dev_set_drvdata(dev, data);
> +	data->dev = dev;
> ?	data->cfg = match->data;
> ?
> ?	res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
> "phy_ctrl");
> -- 
> 2.5.0
>