From: York Sun <york.sun@nxp.com>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH 07/24] powerpc: T1023RDB: Remove macro CONFIG_T1023RDB
Date: Wed, 28 Dec 2016 08:43:33 -0800 [thread overview]
Message-ID: <1482943430-10231-8-git-send-email-york.sun@nxp.com> (raw)
In-Reply-To: <1482943430-10231-1-git-send-email-york.sun@nxp.com>
Use TARGET_T1023RDB from Kconfig instead.
Signed-off-by: York Sun <york.sun@nxp.com>
---
board/freescale/t102xrdb/ddr.c | 2 +-
board/freescale/t102xrdb/eth_t102xrdb.c | 4 ++--
board/freescale/t102xrdb/t102xrdb.c | 12 ++++++------
board/freescale/t102xrdb/t102xrdb.h | 2 +-
configs/T1023RDB_NAND_defconfig | 2 +-
configs/T1023RDB_SDCARD_defconfig | 2 +-
configs/T1023RDB_SECURE_BOOT_defconfig | 1 -
configs/T1023RDB_SPIFLASH_defconfig | 2 +-
configs/T1023RDB_defconfig | 1 -
include/configs/T102xRDB.h | 20 ++++++++++----------
scripts/config_whitelist.txt | 1 -
11 files changed, 23 insertions(+), 26 deletions(-)
diff --git a/board/freescale/t102xrdb/ddr.c b/board/freescale/t102xrdb/ddr.c
index 9e1b16b..c09199f 100644
--- a/board/freescale/t102xrdb/ddr.c
+++ b/board/freescale/t102xrdb/ddr.c
@@ -136,7 +136,7 @@ found:
popts->data_bus_width = DDR_DATA_BUS_WIDTH_32;
#endif
-#ifdef CONFIG_T1023RDB
+#ifdef CONFIG_TARGET_T1023RDB
popts->wrlvl_ctl_2 = 0x07070606;
popts->half_strength_driver_enable = 1;
popts->cpo_sample = 0x43;
diff --git a/board/freescale/t102xrdb/eth_t102xrdb.c b/board/freescale/t102xrdb/eth_t102xrdb.c
index 02b283d..dadfaf1 100644
--- a/board/freescale/t102xrdb/eth_t102xrdb.c
+++ b/board/freescale/t102xrdb/eth_t102xrdb.c
@@ -73,7 +73,7 @@ int board_eth_init(bd_t *bis)
case 0x135:
/* set the on-board 2.5G SGMII AQR105 PHY */
fm_info_set_phy_address(FM1_DTSEC3, SGMII_AQR_PHY_ADDR);
-#ifdef CONFIG_T1023RDB
+#ifdef CONFIG_TARGET_T1023RDB
/* set the on-board 1G SGMII RTL8211F PHY */
fm_info_set_phy_address(FM1_DTSEC1, SGMII_RTK_PHY_ADDR);
#endif
@@ -92,7 +92,7 @@ int board_eth_init(bd_t *bis)
fm_info_set_mdio(i, dev);
break;
case PHY_INTERFACE_MODE_SGMII:
-#if defined(CONFIG_T1023RDB)
+#if defined(CONFIG_TARGET_T1023RDB)
dev = miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME);
#elif defined(CONFIG_T1024RDB)
dev = miiphy_get_dev_by_name(DEFAULT_FM_TGEC_MDIO_NAME);
diff --git a/board/freescale/t102xrdb/t102xrdb.c b/board/freescale/t102xrdb/t102xrdb.c
index 24df4b4..3174726 100644
--- a/board/freescale/t102xrdb/t102xrdb.c
+++ b/board/freescale/t102xrdb/t102xrdb.c
@@ -19,7 +19,7 @@
#include "t102xrdb.h"
#ifdef CONFIG_T1024RDB
#include "cpld.h"
-#elif defined(CONFIG_T1023RDB)
+#elif defined(CONFIG_TARGET_T1023RDB)
#include <i2c.h>
#include <mmc.h>
#endif
@@ -27,7 +27,7 @@
DECLARE_GLOBAL_DATA_PTR;
-#ifdef CONFIG_T1023RDB
+#ifdef CONFIG_TARGET_T1023RDB
enum {
GPIO1_SD_SEL = 0x00020000, /* GPIO1_14, 0: eMMC, 1:SD/MMC */
GPIO1_EMMC_SEL,
@@ -54,7 +54,7 @@ int checkboard(void)
#if defined(CONFIG_T1024RDB)
printf("Board rev: 0x%02x CPLD ver: 0x%02x, ",
CPLD_READ(hw_ver), CPLD_READ(sw_ver));
-#elif defined(CONFIG_T1023RDB)
+#elif defined(CONFIG_TARGET_T1023RDB)
printf("Rev%c, ", t1023rdb_ctrl(GPIO3_GET_VERSION) + 'B');
#endif
printf("boot from ");
@@ -74,7 +74,7 @@ int checkboard(void)
reg = ((reg & CPLD_LBMAP_MASK) >> CPLD_LBMAP_SHIFT);
printf("NOR vBank%d\n", reg);
}
-#elif defined(CONFIG_T1023RDB)
+#elif defined(CONFIG_TARGET_T1023RDB)
#ifdef CONFIG_NAND
puts("NAND\n");
#else
@@ -196,7 +196,7 @@ int ft_board_setup(void *blob, bd_t *bd)
fdt_fixup_board_enet(blob);
#endif
-#ifdef CONFIG_T1023RDB
+#ifdef CONFIG_TARGET_T1023RDB
if (t1023rdb_ctrl(GPIO3_GET_VERSION) > 0)
fdt_enable_nor(blob);
#endif
@@ -204,7 +204,7 @@ int ft_board_setup(void *blob, bd_t *bd)
return 0;
}
-#ifdef CONFIG_T1023RDB
+#ifdef CONFIG_TARGET_T1023RDB
/* Enable NOR flash for RevC */
static void fdt_enable_nor(void *blob)
{
diff --git a/board/freescale/t102xrdb/t102xrdb.h b/board/freescale/t102xrdb/t102xrdb.h
index ae5c60f..6634e7a 100644
--- a/board/freescale/t102xrdb/t102xrdb.h
+++ b/board/freescale/t102xrdb/t102xrdb.h
@@ -9,7 +9,7 @@
void fdt_fixup_board_enet(void *blob);
void pci_of_setup(void *blob, bd_t *bd);
-#ifdef CONFIG_T1023RDB
+#ifdef CONFIG_TARGET_T1023RDB
static u32 t1023rdb_ctrl(u32 ctrl_type);
static void fdt_enable_nor(void *blob);
#endif
diff --git a/configs/T1023RDB_NAND_defconfig b/configs/T1023RDB_NAND_defconfig
index 5649652..71de2a5 100644
--- a/configs/T1023RDB_NAND_defconfig
+++ b/configs/T1023RDB_NAND_defconfig
@@ -12,7 +12,7 @@ CONFIG_FIT=y
CONFIG_FIT_VERBOSE=y
CONFIG_OF_BOARD_SETUP=y
CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_SYS_EXTRA_OPTIONS="T1023RDB,RAMBOOT_PBL,SPL_FSL_PBL,NAND"
+CONFIG_SYS_EXTRA_OPTIONS="RAMBOOT_PBL,SPL_FSL_PBL,NAND"
CONFIG_BOOTDELAY=10
CONFIG_SYS_CONSOLE_IS_IN_ENV=y
CONFIG_SPL=y
diff --git a/configs/T1023RDB_SDCARD_defconfig b/configs/T1023RDB_SDCARD_defconfig
index cc15635..dee5690 100644
--- a/configs/T1023RDB_SDCARD_defconfig
+++ b/configs/T1023RDB_SDCARD_defconfig
@@ -12,7 +12,7 @@ CONFIG_FIT=y
CONFIG_FIT_VERBOSE=y
CONFIG_OF_BOARD_SETUP=y
CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_SYS_EXTRA_OPTIONS="T1023RDB,RAMBOOT_PBL,SPL_FSL_PBL,SDCARD"
+CONFIG_SYS_EXTRA_OPTIONS="RAMBOOT_PBL,SPL_FSL_PBL,SDCARD"
CONFIG_BOOTDELAY=10
CONFIG_SYS_CONSOLE_IS_IN_ENV=y
CONFIG_SPL=y
diff --git a/configs/T1023RDB_SECURE_BOOT_defconfig b/configs/T1023RDB_SECURE_BOOT_defconfig
index 1b474d3..d76c3b9 100644
--- a/configs/T1023RDB_SECURE_BOOT_defconfig
+++ b/configs/T1023RDB_SECURE_BOOT_defconfig
@@ -6,7 +6,6 @@ CONFIG_FIT=y
CONFIG_FIT_VERBOSE=y
CONFIG_OF_BOARD_SETUP=y
CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_SYS_EXTRA_OPTIONS="T1023RDB"
CONFIG_SECURE_BOOT=y
CONFIG_BOOTDELAY=10
CONFIG_SYS_CONSOLE_IS_IN_ENV=y
diff --git a/configs/T1023RDB_SPIFLASH_defconfig b/configs/T1023RDB_SPIFLASH_defconfig
index 28350ad..5fd23e8 100644
--- a/configs/T1023RDB_SPIFLASH_defconfig
+++ b/configs/T1023RDB_SPIFLASH_defconfig
@@ -13,7 +13,7 @@ CONFIG_FIT=y
CONFIG_FIT_VERBOSE=y
CONFIG_OF_BOARD_SETUP=y
CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_SYS_EXTRA_OPTIONS="T1023RDB,RAMBOOT_PBL,SPL_FSL_PBL,SPIFLASH"
+CONFIG_SYS_EXTRA_OPTIONS="RAMBOOT_PBL,SPL_FSL_PBL,SPIFLASH"
CONFIG_BOOTDELAY=10
CONFIG_SYS_CONSOLE_IS_IN_ENV=y
CONFIG_SPL=y
diff --git a/configs/T1023RDB_defconfig b/configs/T1023RDB_defconfig
index ef0005e..255da1b 100644
--- a/configs/T1023RDB_defconfig
+++ b/configs/T1023RDB_defconfig
@@ -5,7 +5,6 @@ CONFIG_FIT=y
CONFIG_FIT_VERBOSE=y
CONFIG_OF_BOARD_SETUP=y
CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_SYS_EXTRA_OPTIONS="T1023RDB"
CONFIG_BOOTDELAY=10
CONFIG_SYS_CONSOLE_IS_IN_ENV=y
CONFIG_HUSH_PARSER=y
diff --git a/include/configs/T102xRDB.h b/include/configs/T102xRDB.h
index f3ba0cd..24eca18 100644
--- a/include/configs/T102xRDB.h
+++ b/include/configs/T102xRDB.h
@@ -62,7 +62,7 @@
#define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot-nand.lds"
#if defined(CONFIG_T1024RDB)
#define CONFIG_SYS_FSL_PBL_RCW board/freescale/t102xrdb/t1024_nand_rcw.cfg
-#elif defined(CONFIG_T1023RDB)
+#elif defined(CONFIG_TARGET_T1023RDB)
#define CONFIG_SYS_FSL_PBL_RCW board/freescale/t102xrdb/t1023_nand_rcw.cfg
#endif
#define CONFIG_SPL_NAND_BOOT
@@ -81,7 +81,7 @@
#endif
#if defined(CONFIG_T1024RDB)
#define CONFIG_SYS_FSL_PBL_RCW board/freescale/t102xrdb/t1024_spi_rcw.cfg
-#elif defined(CONFIG_T1023RDB)
+#elif defined(CONFIG_TARGET_T1023RDB)
#define CONFIG_SYS_FSL_PBL_RCW board/freescale/t102xrdb/t1023_spi_rcw.cfg
#endif
#define CONFIG_SPL_SPI_BOOT
@@ -100,7 +100,7 @@
#endif
#if defined(CONFIG_T1024RDB)
#define CONFIG_SYS_FSL_PBL_RCW board/freescale/t102xrdb/t1024_sd_rcw.cfg
-#elif defined(CONFIG_T1023RDB)
+#elif defined(CONFIG_TARGET_T1023RDB)
#define CONFIG_SYS_FSL_PBL_RCW board/freescale/t102xrdb/t1023_sd_rcw.cfg
#endif
#define CONFIG_SPL_MMC_BOOT
@@ -177,7 +177,7 @@
#define CONFIG_ENV_OFFSET 0x100000 /* 1MB */
#if defined(CONFIG_T1024RDB)
#define CONFIG_ENV_SECT_SIZE 0x10000
-#elif defined(CONFIG_T1023RDB)
+#elif defined(CONFIG_TARGET_T1023RDB)
#define CONFIG_ENV_SECT_SIZE 0x40000
#endif
#elif defined(CONFIG_SDCARD)
@@ -192,7 +192,7 @@
#define CONFIG_ENV_SIZE 0x2000
#if defined(CONFIG_T1024RDB)
#define CONFIG_ENV_OFFSET (2 * CONFIG_SYS_NAND_BLOCK_SIZE)
-#elif defined(CONFIG_T1023RDB)
+#elif defined(CONFIG_TARGET_T1023RDB)
#define CONFIG_ENV_OFFSET (10 * CONFIG_SYS_NAND_BLOCK_SIZE)
#endif
#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
@@ -277,7 +277,7 @@ unsigned long get_board_ddr_clk(void);
#define CONFIG_SYS_SPD_BUS_NUM 0
#define SPD_EEPROM_ADDRESS 0x51
#define CONFIG_SYS_SDRAM_SIZE 4096 /* for fixed parameter use */
-#elif defined(CONFIG_T1023RDB)
+#elif defined(CONFIG_TARGET_T1023RDB)
#define CONFIG_SYS_FSL_DDR4
#define CONFIG_SYS_DDR_RAW_TIMING
#define CONFIG_SYS_SDRAM_SIZE 2048
@@ -303,7 +303,7 @@ unsigned long get_board_ddr_clk(void);
/* NOR Flash Timing Params */
#if defined(CONFIG_T1024RDB)
#define CONFIG_SYS_NOR_CSOR CSOR_NAND_TRHZ_80
-#elif defined(CONFIG_T1023RDB)
+#elif defined(CONFIG_TARGET_T1023RDB)
#define CONFIG_SYS_NOR_CSOR (CSOR_NOR_ADM_SHIFT(0) | \
CSOR_NAND_TRHZ_80 | CSOR_NOR_ADM_SHFT_MODE_EN)
#endif
@@ -378,7 +378,7 @@ unsigned long get_board_ddr_clk(void);
| CSOR_NAND_SPRZ_224 /* Spare size = 224 */ \
| CSOR_NAND_PB(64)) /*Pages Per Block = 64*/
#define CONFIG_SYS_NAND_BLOCK_SIZE (512 * 1024)
-#elif defined(CONFIG_T1023RDB)
+#elif defined(CONFIG_TARGET_T1023RDB)
#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \
| CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \
| CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \
@@ -734,7 +734,7 @@ unsigned long get_board_ddr_clk(void);
#if defined(CONFIG_T1024RDB)
#define CONFIG_SYS_FMAN_FW_ADDR (3 * CONFIG_SYS_NAND_BLOCK_SIZE)
#define CONFIG_SYS_QE_FW_ADDR (4 * CONFIG_SYS_NAND_BLOCK_SIZE)
-#elif defined(CONFIG_T1023RDB)
+#elif defined(CONFIG_TARGET_T1023RDB)
#define CONFIG_SYS_FMAN_FW_ADDR (11 * CONFIG_SYS_NAND_BLOCK_SIZE)
#define CONFIG_SYS_QE_FW_ADDR (12 * CONFIG_SYS_NAND_BLOCK_SIZE)
#endif
@@ -767,7 +767,7 @@ unsigned long get_board_ddr_clk(void);
#define RGMII_PHY2_ADDR 0x6
#define SGMII_AQR_PHY_ADDR 0x2
#define FM1_10GEC1_PHY_ADDR 0x1
-#elif defined(CONFIG_T1023RDB)
+#elif defined(CONFIG_TARGET_T1023RDB)
#define RGMII_PHY1_ADDR 0x1
#define SGMII_RTK_PHY_ADDR 0x3
#define SGMII_AQR_PHY_ADDR 0x2
diff --git a/scripts/config_whitelist.txt b/scripts/config_whitelist.txt
index fcae43a..30519ae 100644
--- a/scripts/config_whitelist.txt
+++ b/scripts/config_whitelist.txt
@@ -7794,7 +7794,6 @@ CONFIG_SYS_XWAY_EBU_BOOTCFG
CONFIG_SYS_ZYNQ_QSPI_WAIT
CONFIG_SYS_ZYNQ_SPI_WAIT
CONFIG_SYS_i2C_FSL
-CONFIG_T1023RDB
CONFIG_T1024RDB
CONFIG_T1040QDS
CONFIG_T2080QDS
--
2.7.4
next prev parent reply other threads:[~2016-12-28 16:43 UTC|newest]
Thread overview: 52+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-12-28 16:43 [U-Boot] [PATCH 00/24] Lift mpc85xx config options to Kconfig York Sun
2016-12-28 16:43 ` [U-Boot] [PATCH 01/24] powerpc: E500: Move CONFIG_E500 and CONFIG_E500MC " York Sun
2017-01-05 13:28 ` [U-Boot] [U-Boot, " Tom Rini
2016-12-28 16:43 ` [U-Boot] [PATCH 02/24] powerpc: mpc85xx: Move CONFIG_SYS_NUM_TLBCAMS " York Sun
2017-01-05 13:28 ` [U-Boot] [U-Boot, " Tom Rini
2016-12-28 16:43 ` [U-Boot] [PATCH 03/24] powerpc: mpc85xx: Move CONFIG_SYS_PPC_E500_DEBUG_TLB " York Sun
2017-01-05 13:28 ` [U-Boot] [U-Boot, " Tom Rini
2016-12-28 16:43 ` [U-Boot] [PATCH 04/24] crypto: Move SYS_FSL_SEC_COMPAT into driver Kconfig York Sun
2017-01-05 13:28 ` [U-Boot] [U-Boot, " Tom Rini
2016-12-28 16:43 ` [U-Boot] [PATCH 05/24] crypto: Move CONFIG_SYS_FSL_SEC_LE and _BE to Kconfig York Sun
2017-01-05 13:28 ` [U-Boot] [U-Boot, " Tom Rini
2016-12-28 16:43 ` [U-Boot] [PATCH 06/24] powerpc: mpc85xx: Remove variant SoCs T1020/T1022/T1013/T1014 York Sun
2017-01-05 13:28 ` [U-Boot] [U-Boot, " Tom Rini
2016-12-28 16:43 ` York Sun [this message]
2017-01-05 13:28 ` [U-Boot] [U-Boot, 07/24] powerpc: T1023RDB: Remove macro CONFIG_T1023RDB Tom Rini
2016-12-28 16:43 ` [U-Boot] [PATCH 08/24] powerpc: T1024RDB: Remove macro CONFIG_T1024RDB York Sun
2017-01-05 13:29 ` [U-Boot] [U-Boot, " Tom Rini
2016-12-28 16:43 ` [U-Boot] [PATCH 09/24] powerpc: T1040QDS: Remove macro CONFIG_T1040QDS York Sun
2017-01-05 13:29 ` [U-Boot] [U-Boot, " Tom Rini
2016-12-28 16:43 ` [U-Boot] [PATCH 10/24] powerpc: T2080QDS: Remove macro T2080QDS York Sun
2017-01-05 13:29 ` [U-Boot] [U-Boot, " Tom Rini
2016-12-28 16:43 ` [U-Boot] [PATCH 11/24] powerpc: T2080RDB: Remove macro CONFIG_T2080RDB York Sun
2017-01-05 13:29 ` [U-Boot] [U-Boot, " Tom Rini
2016-12-28 16:43 ` [U-Boot] [PATCH 12/24] powerpc: T2081QDS: Remove macro T2081QDS York Sun
2017-01-05 13:29 ` [U-Boot] [U-Boot, " Tom Rini
2016-12-28 16:43 ` [U-Boot] [PATCH 13/24] powerpc: T104xQDS: Remove macro CONFIG_T104xD4QDS York Sun
2017-01-05 13:29 ` [U-Boot] [U-Boot, " Tom Rini
2016-12-28 16:43 ` [U-Boot] [PATCH 14/24] fsl_ddr: Move DDR config options to driver Kconfig York Sun
2017-01-05 13:29 ` [U-Boot] [U-Boot, " Tom Rini
2016-12-28 16:43 ` [U-Boot] [PATCH 15/24] arm: layerscape: Move CONFIG_SYS_FSL_ERRATUM_* to Kconfig York Sun
2017-01-05 13:29 ` [U-Boot] [U-Boot, " Tom Rini
2016-12-28 16:43 ` [U-Boot] [PATCH 16/24] mmc: move CONFIG_SYS_FSL_ERRATUM_ESDHC* " York Sun
2017-01-05 13:29 ` [U-Boot] [U-Boot, " Tom Rini
2016-12-28 16:43 ` [U-Boot] [PATCH 17/24] powerpc: mpc85xx: Move CONFIG_SYS_FSL_ERRATUM_* " York Sun
2017-01-05 13:29 ` [U-Boot] [U-Boot, " Tom Rini
2016-12-28 16:43 ` [U-Boot] [PATCH 18/24] ddr: fsl: Move macro CONFIG_NUM_DDR_CONTROLLERS " York Sun
2017-01-05 13:29 ` [U-Boot] [U-Boot, " Tom Rini
2016-12-28 16:43 ` [U-Boot] [PATCH 19/24] ddr: fsl: Merge macro CONFIG_NUM_DDR_CONTROLLERS and CONFIG_SYS_NUM_DDR_CTRLS York Sun
2017-01-05 13:29 ` [U-Boot] [U-Boot, " Tom Rini
2016-12-28 16:43 ` [U-Boot] [PATCH 20/24] ddr: fsl: Move CONFIG_SYS_FSL_DDR_VER to Kconfig York Sun
2017-01-05 13:29 ` [U-Boot] [U-Boot, " Tom Rini
2016-12-28 16:43 ` [U-Boot] [PATCH 21/24] powerpc: mpc85xx: Remove unused ifdef in config header York Sun
2017-01-05 13:30 ` [U-Boot] [U-Boot, " Tom Rini
2016-12-28 16:43 ` [U-Boot] [PATCH 22/24] powerpc: E6500: Move macro CONFIG_E6500 to Kconfig York Sun
2017-01-05 13:30 ` [U-Boot] [U-Boot, " Tom Rini
2016-12-28 16:43 ` [U-Boot] [PATCH 23/24] powerpc: mpc85xx: Move CONFIG_SYS_FSL_QORIQ_CHASSIS* " York Sun
2017-01-05 13:30 ` [U-Boot] [U-Boot, " Tom Rini
2016-12-28 16:43 ` [U-Boot] [PATCH 24/24] powerpc: mpc85xx: Move macro CONFIG_SYS_PPC64 " York Sun
2017-01-05 13:30 ` [U-Boot] [U-Boot, " Tom Rini
2017-01-05 13:28 ` [U-Boot] [PATCH 00/24] Lift mpc85xx config options " Tom Rini
2017-01-05 16:28 ` york sun
2017-01-05 17:34 ` york sun
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1482943430-10231-8-git-send-email-york.sun@nxp.com \
--to=york.sun@nxp.com \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.