All of lore.kernel.org
 help / color / mirror / Atom feed
From: embed3d@gmail.com (Philipp Rossak)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH v2 2/2] ARM: dts: sun8i: h3: Improved Wifi bindings on Bananapi M2 Plus
Date: Fri,  1 Sep 2017 18:30:01 +0200	[thread overview]
Message-ID: <1504283401-4263-3-git-send-email-embed3d@gmail.com> (raw)
In-Reply-To: <1504283401-4263-1-git-send-email-embed3d@gmail.com>

From: Philipp Rossak <embed3d@gmail.com>

* vqmmc is in this case not needed
* no need for pincontrol nodes when the pin is set to a GPIO

Signed-off-by: Philipp Rossak <embed3d@gmail.com>
---
 arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts | 7 -------
 1 file changed, 7 deletions(-)

diff --git a/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts b/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts
index d756ff8..f7e5d8a 100644
--- a/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts
+++ b/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts
@@ -98,7 +98,6 @@
 	wifi_pwrseq: wifi_pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		pinctrl-names = "default";
-		pinctrl-0 = <&wifi_en_bpi_m2p>;
 		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
 	};
 };
@@ -153,7 +152,6 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc1_pins_a>;
 	vmmc-supply = <&reg_vcc3v3>;
-	vqmmc-supply = <&reg_vcc3v3>;
 	mmc-pwrseq = <&wifi_pwrseq>;
 	bus-width = <4>;
 	non-removable;
@@ -200,11 +198,6 @@
 		pins = "PL3";
 		function = "gpio_in";
 	};
-
-	wifi_en_bpi_m2p: wifi_en_pin {
-		pins = "PL7";
-		function = "gpio_out";
-	};
 };
 
 &reg_usb0_vbus {
-- 
2.7.4

WARNING: multiple messages have this Message-ID (diff)
From: Philipp Rossak <embed3d-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
To: robh+dt-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org,
	mark.rutland-5wv7dgnIgG8@public.gmane.org,
	linux-I+IVW8TIWO2tmTQ+vhA3Yw@public.gmane.org,
	maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org,
	wens-jdAy2FN1RRM@public.gmane.org
Cc: Philipp Rossak <embed3d-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>,
	devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
	linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org,
	linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
	linux-sunxi-/JYPxA39Uh5TLH3MbocFFw@public.gmane.org
Subject: [PATCH v2 2/2] ARM: dts: sun8i: h3: Improved Wifi bindings on Bananapi M2 Plus
Date: Fri,  1 Sep 2017 18:30:01 +0200	[thread overview]
Message-ID: <1504283401-4263-3-git-send-email-embed3d@gmail.com> (raw)
In-Reply-To: <1504283401-4263-1-git-send-email-embed3d-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>

From: Philipp Rossak <embed3d-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>

* vqmmc is in this case not needed
* no need for pincontrol nodes when the pin is set to a GPIO

Signed-off-by: Philipp Rossak <embed3d-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
---
 arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts | 7 -------
 1 file changed, 7 deletions(-)

diff --git a/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts b/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts
index d756ff8..f7e5d8a 100644
--- a/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts
+++ b/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts
@@ -98,7 +98,6 @@
 	wifi_pwrseq: wifi_pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		pinctrl-names = "default";
-		pinctrl-0 = <&wifi_en_bpi_m2p>;
 		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
 	};
 };
@@ -153,7 +152,6 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc1_pins_a>;
 	vmmc-supply = <&reg_vcc3v3>;
-	vqmmc-supply = <&reg_vcc3v3>;
 	mmc-pwrseq = <&wifi_pwrseq>;
 	bus-width = <4>;
 	non-removable;
@@ -200,11 +198,6 @@
 		pins = "PL3";
 		function = "gpio_in";
 	};
-
-	wifi_en_bpi_m2p: wifi_en_pin {
-		pins = "PL7";
-		function = "gpio_out";
-	};
 };
 
 &reg_usb0_vbus {
-- 
2.7.4

WARNING: multiple messages have this Message-ID (diff)
From: Philipp Rossak <embed3d@gmail.com>
To: robh+dt@kernel.org, mark.rutland@arm.com, linux@armlinux.org.uk,
	maxime.ripard@free-electrons.com, wens@csie.org
Cc: Philipp Rossak <embed3d@gmail.com>,
	devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
	linux-kernel@vger.kernel.org, linux-sunxi@googlegroups.com
Subject: [PATCH v2 2/2] ARM: dts: sun8i: h3: Improved Wifi bindings on Bananapi M2 Plus
Date: Fri,  1 Sep 2017 18:30:01 +0200	[thread overview]
Message-ID: <1504283401-4263-3-git-send-email-embed3d@gmail.com> (raw)
In-Reply-To: <1504283401-4263-1-git-send-email-embed3d@gmail.com>

From: Philipp Rossak <embed3d@gmail.com>

* vqmmc is in this case not needed
* no need for pincontrol nodes when the pin is set to a GPIO

Signed-off-by: Philipp Rossak <embed3d@gmail.com>
---
 arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts | 7 -------
 1 file changed, 7 deletions(-)

diff --git a/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts b/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts
index d756ff8..f7e5d8a 100644
--- a/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts
+++ b/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts
@@ -98,7 +98,6 @@
 	wifi_pwrseq: wifi_pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		pinctrl-names = "default";
-		pinctrl-0 = <&wifi_en_bpi_m2p>;
 		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
 	};
 };
@@ -153,7 +152,6 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc1_pins_a>;
 	vmmc-supply = <&reg_vcc3v3>;
-	vqmmc-supply = <&reg_vcc3v3>;
 	mmc-pwrseq = <&wifi_pwrseq>;
 	bus-width = <4>;
 	non-removable;
@@ -200,11 +198,6 @@
 		pins = "PL3";
 		function = "gpio_in";
 	};
-
-	wifi_en_bpi_m2p: wifi_en_pin {
-		pins = "PL7";
-		function = "gpio_out";
-	};
 };
 
 &reg_usb0_vbus {
-- 
2.7.4

  parent reply	other threads:[~2017-09-01 16:30 UTC|newest]

Thread overview: 23+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2017-09-01 16:29 [PATCH v2 0/2] [DTS] Enable hardware for Nanopi M1 & Nanopi M1 Plus Philipp Rossak
2017-09-01 16:29 ` Philipp Rossak
2017-09-01 16:30 ` [PATCH v2 1/2] ARM: dts: sun8i: h3: Enable AP6212 WiFi on mmc1 on " Philipp Rossak
2017-09-01 16:30   ` Philipp Rossak
2017-09-01 16:30   ` Philipp Rossak
2017-09-02  7:01   ` icenowy at aosc.io
2017-09-02  7:01     ` icenowy
2017-09-02  7:01     ` icenowy-h8G6r0blFSE
2017-09-04  8:04     ` Maxime Ripard
2017-09-04  8:04       ` Maxime Ripard
2017-09-04  8:04       ` Maxime Ripard
2017-09-04  8:02   ` Maxime Ripard
2017-09-04  8:02     ` Maxime Ripard
2017-09-04  8:02     ` Maxime Ripard
2017-09-01 16:30 ` Philipp Rossak [this message]
2017-09-01 16:30   ` [PATCH v2 2/2] ARM: dts: sun8i: h3: Improved Wifi bindings on Bananapi M2 Plus Philipp Rossak
2017-09-01 16:30   ` Philipp Rossak
2017-09-04  8:05   ` Maxime Ripard
2017-09-04  8:05     ` Maxime Ripard
2017-09-04  8:05     ` Maxime Ripard
2017-09-04 13:52     ` Philipp Rossak
2017-09-04 13:52       ` Philipp Rossak
2017-09-04 13:52       ` Philipp Rossak

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1504283401-4263-3-git-send-email-embed3d@gmail.com \
    --to=embed3d@gmail.com \
    --cc=linux-arm-kernel@lists.infradead.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.