[PATCH v4 4/6] tty: serial: msm_geni_serial: Add serial driver support for GENI based QUP

[Karthikeyan Ramasubramanian <kramasub@codeaurora.org>]

This driver supports GENI based UART Controller in the Qualcomm SOCs. The
Qualcomm Generic Interface (GENI) is a programmable module supporting a
wide range of serial interfaces including UART. This driver support console
operations using FIFO mode of transfer.

Signed-off-by: Girish Mahadevan <girishm@codeaurora.org>
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@codeaurora.org>
Signed-off-by: Sagar Dharia <sdharia@codeaurora.org>
Signed-off-by: Doug Anderson <dianders@google.com>
---
 drivers/tty/serial/Kconfig            |   15 +
 drivers/tty/serial/Makefile           |    1 +
 drivers/tty/serial/qcom_geni_serial.c | 1158 +++++++++++++++++++++++++++++++++
 3 files changed, 1174 insertions(+)
 create mode 100644 drivers/tty/serial/qcom_geni_serial.c

diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig
index 3682fd3..d132971 100644
--- a/drivers/tty/serial/Kconfig
+++ b/drivers/tty/serial/Kconfig
@@ -1104,6 +1104,21 @@ config SERIAL_MSM_CONSOLE
 	select SERIAL_CORE_CONSOLE
 	select SERIAL_EARLYCON
 
+config SERIAL_QCOM_GENI
+	tristate "QCOM on-chip GENI based serial port support"
+	depends on ARCH_QCOM || COMPILE_TEST
+	depends on QCOM_GENI_SE
+	select SERIAL_CORE
+
+config SERIAL_QCOM_GENI_CONSOLE
+	bool "QCOM GENI Serial Console support"
+	depends on SERIAL_QCOM_GENI=y
+	select SERIAL_CORE_CONSOLE
+	select SERIAL_EARLYCON
+	help
+	  Serial console driver for Qualcomm Technologies Inc's GENI based
+	  QUP hardware.
+
 config SERIAL_VT8500
 	bool "VIA VT8500 on-chip serial port support"
 	depends on ARCH_VT8500
diff --git a/drivers/tty/serial/Makefile b/drivers/tty/serial/Makefile
index 842d185..64a8d82 100644
--- a/drivers/tty/serial/Makefile
+++ b/drivers/tty/serial/Makefile
@@ -63,6 +63,7 @@ obj-$(CONFIG_SERIAL_SGI_IOC3) += ioc3_serial.o
 obj-$(CONFIG_SERIAL_ATMEL) += atmel_serial.o
 obj-$(CONFIG_SERIAL_UARTLITE) += uartlite.o
 obj-$(CONFIG_SERIAL_MSM) += msm_serial.o
+obj-$(CONFIG_SERIAL_QCOM_GENI) += qcom_geni_serial.o
 obj-$(CONFIG_SERIAL_NETX) += netx-serial.o
 obj-$(CONFIG_SERIAL_KS8695) += serial_ks8695.o
 obj-$(CONFIG_SERIAL_OMAP) += omap-serial.o
diff --git a/drivers/tty/serial/qcom_geni_serial.c b/drivers/tty/serial/qcom_geni_serial.c
new file mode 100644
index 0000000..1442777
--- /dev/null
+++ b/drivers/tty/serial/qcom_geni_serial.c
@@ -0,0 +1,1158 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2017-2018, The Linux foundation. All rights reserved.
+
+#include <linux/clk.h>
+#include <linux/console.h>
+#include <linux/io.h>
+#include <linux/iopoll.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/qcom-geni-se.h>
+#include <linux/serial.h>
+#include <linux/serial_core.h>
+#include <linux/slab.h>
+#include <linux/tty.h>
+#include <linux/tty_flip.h>
+
+/* UART specific GENI registers */
+#define SE_UART_TX_TRANS_CFG		0x25c
+#define SE_UART_TX_WORD_LEN		0x268
+#define SE_UART_TX_STOP_BIT_LEN		0x26c
+#define SE_UART_TX_TRANS_LEN		0x270
+#define SE_UART_RX_TRANS_CFG		0x280
+#define SE_UART_RX_WORD_LEN		0x28c
+#define SE_UART_RX_STALE_CNT		0x294
+#define SE_UART_TX_PARITY_CFG		0x2a4
+#define SE_UART_RX_PARITY_CFG		0x2a8
+
+/* SE_UART_TRANS_CFG */
+#define UART_TX_PAR_EN		BIT(0)
+#define UART_CTS_MASK		BIT(1)
+
+/* SE_UART_TX_WORD_LEN */
+#define TX_WORD_LEN_MSK		GENMASK(9, 0)
+
+/* SE_UART_TX_STOP_BIT_LEN */
+#define TX_STOP_BIT_LEN_MSK	GENMASK(23, 0)
+#define TX_STOP_BIT_LEN_1	0
+#define TX_STOP_BIT_LEN_1_5	1
+#define TX_STOP_BIT_LEN_2	2
+
+/* SE_UART_TX_TRANS_LEN */
+#define TX_TRANS_LEN_MSK	GENMASK(23, 0)
+
+/* SE_UART_RX_TRANS_CFG */
+#define UART_RX_INS_STATUS_BIT	BIT(2)
+#define UART_RX_PAR_EN		BIT(3)
+
+/* SE_UART_RX_WORD_LEN */
+#define RX_WORD_LEN_MASK	GENMASK(9, 0)
+
+/* SE_UART_RX_STALE_CNT */
+#define RX_STALE_CNT		GENMASK(23, 0)
+
+/* SE_UART_TX_PARITY_CFG/RX_PARITY_CFG */
+#define PAR_CALC_EN		BIT(0)
+#define PAR_MODE_MSK		GENMASK(2, 1)
+#define PAR_MODE_SHFT		1
+#define PAR_EVEN		0x00
+#define PAR_ODD			0x01
+#define PAR_SPACE		0x10
+#define PAR_MARK		0x11
+
+/* UART M_CMD OP codes */
+#define UART_START_TX		0x1
+#define UART_START_BREAK	0x4
+#define UART_STOP_BREAK		0x5
+/* UART S_CMD OP codes */
+#define UART_START_READ		0x1
+#define UART_PARAM		0x1
+
+#define UART_OVERSAMPLING	32
+#define STALE_TIMEOUT		16
+#define DEFAULT_BITS_PER_CHAR	10
+#define GENI_UART_CONS_PORTS	1
+#define DEF_FIFO_DEPTH_WORDS	16
+#define DEF_TX_WM		2
+#define DEF_FIFO_WIDTH_BITS	32
+#define UART_CONSOLE_RX_WM	2
+
+#ifdef CONFIG_CONSOLE_POLL
+#define RX_BYTES_PW 1
+#else
+#define RX_BYTES_PW 4
+#endif
+
+struct qcom_geni_serial_port {
+	struct uart_port uport;
+	struct geni_se se;
+	char name[20];
+	u32 tx_fifo_depth;
+	u32 tx_fifo_width;
+	u32 rx_fifo_depth;
+	u32 tx_wm;
+	u32 rx_wm;
+	u32 rx_rfr;
+	enum geni_se_xfer_mode xfer_mode;
+	bool setup;
+	int (*handle_rx)(struct uart_port *uport, u32 bytes, bool drop);
+	unsigned int xmit_size;
+	unsigned int baud;
+	unsigned int tx_bytes_pw;
+	unsigned int rx_bytes_pw;
+	bool brk;
+};
+
+static const struct uart_ops qcom_geni_serial_pops;
+static struct uart_driver qcom_geni_console_driver;
+static int handle_rx_console(struct uart_port *uport, u32 bytes, bool drop);
+static unsigned int qcom_geni_serial_tx_empty(struct uart_port *port);
+static void qcom_geni_serial_stop_rx(struct uart_port *uport);
+
+static const unsigned long root_freq[] = {7372800, 14745600, 19200000, 29491200,
+					32000000, 48000000, 64000000, 80000000,
+					96000000, 100000000};
+
+#define to_dev_port(ptr, member) \
+		container_of(ptr, struct qcom_geni_serial_port, member)
+
+static struct qcom_geni_serial_port qcom_geni_console_port;
+
+static int qcom_geni_serial_request_port(struct uart_port *uport)
+{
+	struct platform_device *pdev = to_platform_device(uport->dev);
+	struct qcom_geni_serial_port *port = to_dev_port(uport, uport);
+	struct resource *res;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	uport->membase = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(uport->membase))
+		return PTR_ERR(uport->membase);
+	port->se.base = uport->membase;
+	return 0;
+}
+
+static void qcom_geni_serial_config_port(struct uart_port *uport, int cfg_flags)
+{
+	if (cfg_flags & UART_CONFIG_TYPE) {
+		uport->type = PORT_MSM;
+		qcom_geni_serial_request_port(uport);
+	}
+}
+
+static unsigned int qcom_geni_cons_get_mctrl(struct uart_port *uport)
+{
+	return TIOCM_DSR | TIOCM_CAR | TIOCM_CTS;
+}
+
+static void qcom_geni_cons_set_mctrl(struct uart_port *uport,
+							unsigned int mctrl)
+{
+}
+
+static const char *qcom_geni_serial_get_type(struct uart_port *uport)
+{
+	return "MSM";
+}
+
+static struct qcom_geni_serial_port *get_port_from_line(int line)
+{
+	if (line < 0 || line >= GENI_UART_CONS_PORTS)
+		return ERR_PTR(-ENXIO);
+	return &qcom_geni_console_port;
+}
+
+static bool qcom_geni_serial_poll_bit(struct uart_port *uport,
+				int offset, int field, bool set)
+{
+	u32 reg;
+	struct qcom_geni_serial_port *port;
+	unsigned int baud;
+	unsigned int fifo_bits;
+	unsigned long timeout_us = 20000;
+
+	/* Ensure polling is not re-ordered before the prior writes/reads */
+	mb();
+
+	if (uport->private_data) {
+		port = to_dev_port(uport, uport);
+		baud = port->baud;
+		if (!baud)
+			baud = 115200;
+		fifo_bits = port->tx_fifo_depth * port->tx_fifo_width;
+		/*
+		 * Total polling iterations based on FIFO worth of bytes to be
+		 * sent at current baud. Add a little fluff to the wait.
+		 */
+		timeout_us = ((fifo_bits * USEC_PER_SEC) / baud) + 500;
+	}
+
+	return !readl_poll_timeout_atomic(uport->membase + offset, reg,
+			 (bool)(reg & field) == set, 10, timeout_us);
+}
+
+static void qcom_geni_serial_setup_tx(struct uart_port *uport, u32 xmit_size)
+{
+	u32 m_cmd;
+
+	writel_relaxed(xmit_size, uport->membase + SE_UART_TX_TRANS_LEN);
+	m_cmd = UART_START_TX << M_OPCODE_SHFT;
+	writel(m_cmd, uport->membase + SE_GENI_M_CMD0);
+}
+
+static void qcom_geni_serial_poll_tx_done(struct uart_port *uport)
+{
+	int done;
+	u32 irq_clear = M_CMD_DONE_EN;
+
+	done = qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS,
+						M_CMD_DONE_EN, true);
+	if (!done) {
+		writel_relaxed(M_GENI_CMD_ABORT, uport->membase +
+						SE_GENI_M_CMD_CTRL_REG);
+		irq_clear |= M_CMD_ABORT_EN;
+		qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS,
+							M_CMD_ABORT_EN, true);
+	}
+	writel_relaxed(irq_clear, uport->membase + SE_GENI_M_IRQ_CLEAR);
+}
+
+static void qcom_geni_serial_abort_rx(struct uart_port *uport)
+{
+	u32 irq_clear = S_CMD_DONE_EN | S_CMD_ABORT_EN;
+
+	writel(S_GENI_CMD_ABORT, uport->membase + SE_GENI_S_CMD_CTRL_REG);
+	qcom_geni_serial_poll_bit(uport, SE_GENI_S_CMD_CTRL_REG,
+					S_GENI_CMD_ABORT, false);
+	writel_relaxed(irq_clear, uport->membase + SE_GENI_S_IRQ_CLEAR);
+	writel_relaxed(FORCE_DEFAULT, uport->membase + GENI_FORCE_DEFAULT_REG);
+}
+
+#ifdef CONFIG_CONSOLE_POLL
+static int qcom_geni_serial_get_char(struct uart_port *uport)
+{
+	u32 rx_fifo;
+	u32 status;
+
+	status = readl_relaxed(uport->membase + SE_GENI_M_IRQ_STATUS);
+	writel_relaxed(status, uport->membase + SE_GENI_M_IRQ_CLEAR);
+
+	status = readl_relaxed(uport->membase + SE_GENI_S_IRQ_STATUS);
+	writel_relaxed(status, uport->membase + SE_GENI_S_IRQ_CLEAR);
+
+	/*
+	 * Ensure the writes to clear interrupts is not re-ordered after
+	 * reading the data.
+	 */
+	mb();
+
+	status = readl_relaxed(uport->membase + SE_GENI_RX_FIFO_STATUS);
+	if (!(status & RX_FIFO_WC_MSK))
+		return NO_POLL_CHAR;
+
+	rx_fifo = readl(uport->membase + SE_GENI_RX_FIFOn);
+	return rx_fifo & 0xff;
+}
+
+static void qcom_geni_serial_poll_put_char(struct uart_port *uport,
+							unsigned char c)
+{
+	struct qcom_geni_serial_port *port = to_dev_port(uport, uport);
+
+	writel_relaxed(port->tx_wm, uport->membase + SE_GENI_TX_WATERMARK_REG);
+	qcom_geni_serial_setup_tx(uport, 1);
+	WARN_ON(!qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS,
+						M_TX_FIFO_WATERMARK_EN, true));
+	writel_relaxed(c, uport->membase + SE_GENI_TX_FIFOn);
+	writel_relaxed(M_TX_FIFO_WATERMARK_EN, uport->membase +
+							SE_GENI_M_IRQ_CLEAR);
+	qcom_geni_serial_poll_tx_done(uport);
+}
+#endif
+
+#ifdef CONFIG_SERIAL_QCOM_GENI_CONSOLE
+static void qcom_geni_serial_wr_char(struct uart_port *uport, int ch)
+{
+	writel_relaxed(ch, uport->membase + SE_GENI_TX_FIFOn);
+}
+
+static void
+__qcom_geni_serial_console_write(struct uart_port *uport, const char *s,
+				 unsigned int count)
+{
+	int i;
+	u32 bytes_to_send = count;
+
+	for (i = 0; i < count; i++) {
+		if (s[i] == '\n')
+			bytes_to_send++;
+	}
+
+	writel_relaxed(DEF_TX_WM, uport->membase + SE_GENI_TX_WATERMARK_REG);
+	qcom_geni_serial_setup_tx(uport, bytes_to_send);
+	for (i = 0; i < count; ) {
+		size_t chars_to_write = 0;
+		size_t avail = DEF_FIFO_DEPTH_WORDS - DEF_TX_WM;
+
+		/*
+		 * If the WM bit never set, then the Tx state machine is not
+		 * in a valid state, so break, cancel/abort any existing
+		 * command. Unfortunately the current data being written is
+		 * lost.
+		 */
+		if (!qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS,
+						M_TX_FIFO_WATERMARK_EN, true))
+			break;
+		chars_to_write = min_t(size_t, (size_t)(count - i), avail / 2);
+		uart_console_write(uport, s + i, chars_to_write,
+						qcom_geni_serial_wr_char);
+		writel_relaxed(M_TX_FIFO_WATERMARK_EN, uport->membase +
+							SE_GENI_M_IRQ_CLEAR);
+		i += chars_to_write;
+	}
+	qcom_geni_serial_poll_tx_done(uport);
+}
+
+static void qcom_geni_serial_console_write(struct console *co, const char *s,
+			      unsigned int count)
+{
+	struct uart_port *uport;
+	struct qcom_geni_serial_port *port;
+	bool locked = true;
+	unsigned long flags;
+
+	WARN_ON(co->index < 0 || co->index >= GENI_UART_CONS_PORTS);
+
+	port = get_port_from_line(co->index);
+	if (IS_ERR(port))
+		return;
+
+	uport = &port->uport;
+	if (oops_in_progress)
+		locked = spin_trylock_irqsave(&uport->lock, flags);
+	else
+		spin_lock_irqsave(&uport->lock, flags);
+
+	/* Cancel the current write to log the fault */
+	if (!locked) {
+		geni_se_cancel_m_cmd(&port->se);
+		if (!qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS,
+						M_CMD_CANCEL_EN, true)) {
+			geni_se_abort_m_cmd(&port->se);
+			qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS,
+							M_CMD_ABORT_EN, true);
+			writel_relaxed(M_CMD_ABORT_EN, uport->membase +
+							SE_GENI_M_IRQ_CLEAR);
+		}
+		writel_relaxed(M_CMD_CANCEL_EN, uport->membase +
+							SE_GENI_M_IRQ_CLEAR);
+	}
+
+	__qcom_geni_serial_console_write(uport, s, count);
+	if (locked)
+		spin_unlock_irqrestore(&uport->lock, flags);
+}
+
+static int handle_rx_console(struct uart_port *uport, u32 bytes, bool drop)
+{
+	u32 i;
+	unsigned char buf[sizeof(u32)];
+	struct tty_port *tport;
+	struct qcom_geni_serial_port *port = to_dev_port(uport, uport);
+
+	tport = &uport->state->port;
+	for (i = 0; i < bytes; ) {
+		int c;
+		int chunk = min_t(int, bytes - i, port->rx_bytes_pw);
+
+		ioread32_rep(uport->membase + SE_GENI_RX_FIFOn, buf, 1);
+		i += chunk;
+		if (drop)
+			continue;
+
+		for (c = 0; c < chunk; c++) {
+			int sysrq;
+
+			uport->icount.rx++;
+			if (port->brk && buf[c] == 0) {
+				port->brk = false;
+				if (uart_handle_break(uport))
+					continue;
+			}
+
+			sysrq = uart_handle_sysrq_char(uport, buf[c]);
+			if (!sysrq)
+				tty_insert_flip_char(tport, buf[c], TTY_NORMAL);
+		}
+	}
+	if (!drop)
+		tty_flip_buffer_push(tport);
+	return 0;
+}
+#else
+static int handle_rx_console(struct uart_port *uport, u32 bytes, bool drop)
+{
+	return -EPERM;
+}
+
+#endif /* CONFIG_SERIAL_QCOM_GENI_CONSOLE */
+
+static void qcom_geni_serial_start_tx(struct uart_port *uport)
+{
+	u32 irq_en;
+	struct qcom_geni_serial_port *port = to_dev_port(uport, uport);
+	u32 status;
+
+	if (port->xfer_mode == GENI_SE_FIFO) {
+		status = readl_relaxed(uport->membase + SE_GENI_STATUS);
+		if (status & M_GENI_CMD_ACTIVE)
+			return;
+
+		if (!qcom_geni_serial_tx_empty(uport))
+			return;
+
+		/*
+		 * Ensure writing to IRQ_EN & watermark registers are not
+		 * re-ordered before checking the status of the Serial
+		 * Engine and TX FIFO
+		 */
+		mb();
+
+		irq_en = readl_relaxed(uport->membase +	SE_GENI_M_IRQ_EN);
+		irq_en |= M_TX_FIFO_WATERMARK_EN | M_CMD_DONE_EN;
+
+		writel_relaxed(port->tx_wm, uport->membase +
+						SE_GENI_TX_WATERMARK_REG);
+		writel_relaxed(irq_en, uport->membase +	SE_GENI_M_IRQ_EN);
+	}
+}
+
+static void qcom_geni_serial_stop_tx(struct uart_port *uport)
+{
+	u32 irq_en;
+	u32 status;
+	struct qcom_geni_serial_port *port = to_dev_port(uport, uport);
+
+	irq_en = readl_relaxed(uport->membase + SE_GENI_M_IRQ_EN);
+	irq_en &= ~M_CMD_DONE_EN;
+	if (port->xfer_mode == GENI_SE_FIFO) {
+		irq_en &= ~M_TX_FIFO_WATERMARK_EN;
+		writel_relaxed(0, uport->membase +
+				     SE_GENI_TX_WATERMARK_REG);
+	}
+	port->xmit_size = 0;
+	writel_relaxed(irq_en, uport->membase + SE_GENI_M_IRQ_EN);
+	status = readl_relaxed(uport->membase + SE_GENI_STATUS);
+	/* Possible stop tx is called multiple times. */
+	if (!(status & M_GENI_CMD_ACTIVE))
+		return;
+
+	/*
+	 * Ensure cancel command write is not re-ordered before checking
+	 * the status of the Primary Sequencer.
+	 */
+	mb();
+
+	geni_se_cancel_m_cmd(&port->se);
+	if (!qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS,
+						M_CMD_CANCEL_EN, true)) {
+		geni_se_abort_m_cmd(&port->se);
+		qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS,
+						M_CMD_ABORT_EN, true);
+		writel_relaxed(M_CMD_ABORT_EN, uport->membase +
+							SE_GENI_M_IRQ_CLEAR);
+	}
+	writel_relaxed(M_CMD_CANCEL_EN, uport->membase + SE_GENI_M_IRQ_CLEAR);
+}
+
+static void qcom_geni_serial_start_rx(struct uart_port *uport)
+{
+	u32 irq_en;
+	u32 status;
+	struct qcom_geni_serial_port *port = to_dev_port(uport, uport);
+
+	status = readl_relaxed(uport->membase + SE_GENI_STATUS);
+	if (status & S_GENI_CMD_ACTIVE)
+		qcom_geni_serial_stop_rx(uport);
+
+	/*
+	 * Ensure setup command write is not re-ordered before checking
+	 * the status of the Secondary Sequencer.
+	 */
+	mb();
+
+	geni_se_setup_s_cmd(&port->se, UART_START_READ, 0);
+
+	if (port->xfer_mode == GENI_SE_FIFO) {
+		irq_en = readl_relaxed(uport->membase + SE_GENI_S_IRQ_EN);
+		irq_en |= S_RX_FIFO_WATERMARK_EN | S_RX_FIFO_LAST_EN;
+		writel_relaxed(irq_en, uport->membase + SE_GENI_S_IRQ_EN);
+
+		irq_en = readl_relaxed(uport->membase + SE_GENI_M_IRQ_EN);
+		irq_en |= M_RX_FIFO_WATERMARK_EN | M_RX_FIFO_LAST_EN;
+		writel_relaxed(irq_en, uport->membase + SE_GENI_M_IRQ_EN);
+	}
+}
+
+static void qcom_geni_serial_stop_rx(struct uart_port *uport)
+{
+	u32 irq_en;
+	u32 status;
+	struct qcom_geni_serial_port *port = to_dev_port(uport, uport);
+	u32 irq_clear = S_CMD_DONE_EN;
+
+	if (port->xfer_mode == GENI_SE_FIFO) {
+		irq_en = readl_relaxed(uport->membase + SE_GENI_S_IRQ_EN);
+		irq_en &= ~(S_RX_FIFO_WATERMARK_EN | S_RX_FIFO_LAST_EN);
+		writel_relaxed(irq_en, uport->membase + SE_GENI_S_IRQ_EN);
+
+		irq_en = readl_relaxed(uport->membase + SE_GENI_M_IRQ_EN);
+		irq_en &= ~(M_RX_FIFO_WATERMARK_EN | M_RX_FIFO_LAST_EN);
+		writel_relaxed(irq_en, uport->membase + SE_GENI_M_IRQ_EN);
+	}
+
+	status = readl_relaxed(uport->membase + SE_GENI_STATUS);
+	/* Possible stop rx is called multiple times. */
+	if (!(status & S_GENI_CMD_ACTIVE))
+		return;
+
+	/*
+	 * Ensure cancel command write is not re-ordered before checking
+	 * the status of the Secondary Sequencer.
+	 */
+	mb();
+
+	geni_se_cancel_s_cmd(&port->se);
+	qcom_geni_serial_poll_bit(uport, SE_GENI_S_CMD_CTRL_REG,
+					S_GENI_CMD_CANCEL, false);
+	status = readl_relaxed(uport->membase + SE_GENI_STATUS);
+	writel_relaxed(irq_clear, uport->membase + SE_GENI_S_IRQ_CLEAR);
+	if (status & S_GENI_CMD_ACTIVE)
+		qcom_geni_serial_abort_rx(uport);
+}
+
+static void qcom_geni_serial_handle_rx(struct uart_port *uport, bool drop)
+{
+	u32 status;
+	u32 word_cnt;
+	u32 last_word_byte_cnt;
+	u32 last_word_partial;
+	u32 total_bytes;
+	struct qcom_geni_serial_port *port = to_dev_port(uport, uport);
+
+	status = readl_relaxed(uport->membase +	SE_GENI_RX_FIFO_STATUS);
+	word_cnt = status & RX_FIFO_WC_MSK;
+	last_word_partial = status & RX_LAST;
+	last_word_byte_cnt = (status & RX_LAST_BYTE_VALID_MSK) >>
+						RX_LAST_BYTE_VALID_SHFT;
+
+	if (!word_cnt)
+		return;
+	total_bytes = port->rx_bytes_pw * (word_cnt - 1);
+	if (last_word_partial && last_word_byte_cnt)
+		total_bytes += last_word_byte_cnt;
+	else
+		total_bytes += port->rx_bytes_pw;
+	port->handle_rx(uport, total_bytes, drop);
+}
+
+static void qcom_geni_serial_handle_tx(struct uart_port *uport)
+{
+	struct qcom_geni_serial_port *port = to_dev_port(uport, uport);
+	struct circ_buf *xmit = &uport->state->xmit;
+	size_t avail;
+	size_t remaining;
+	int i;
+	u32 status;
+	unsigned int chunk;
+	int tail;
+
+	chunk = uart_circ_chars_pending(xmit);
+	status = readl_relaxed(uport->membase + SE_GENI_TX_FIFO_STATUS);
+	/* Both FIFO and framework buffer are drained */
+	if (chunk == port->xmit_size && !status) {
+		port->xmit_size = 0;
+		uart_circ_clear(xmit);
+		qcom_geni_serial_stop_tx(uport);
+		goto out_write_wakeup;
+	}
+	chunk -= port->xmit_size;
+
+	avail = (port->tx_fifo_depth - port->tx_wm) * port->tx_bytes_pw;
+	tail = (xmit->tail + port->xmit_size) & (UART_XMIT_SIZE - 1);
+	if (chunk > (UART_XMIT_SIZE - tail))
+		chunk = UART_XMIT_SIZE - tail;
+	if (chunk > avail)
+		chunk = avail;
+
+	if (!chunk)
+		goto out_write_wakeup;
+
+	qcom_geni_serial_setup_tx(uport, chunk);
+
+	remaining = chunk;
+	for (i = 0; i < chunk; ) {
+		unsigned int tx_bytes;
+		unsigned int buf = 0;
+		int c;
+
+		tx_bytes = min_t(size_t, remaining, (size_t)port->tx_bytes_pw);
+		for (c = 0; c < tx_bytes ; c++)
+			buf |= (xmit->buf[tail + c] << (c * BITS_PER_BYTE));
+
+		writel_relaxed(buf, uport->membase + SE_GENI_TX_FIFOn);
+
+		i += tx_bytes;
+		tail = (tail + tx_bytes) & (UART_XMIT_SIZE - 1);
+		uport->icount.tx += tx_bytes;
+		remaining -= tx_bytes;
+	}
+	qcom_geni_serial_poll_tx_done(uport);
+	port->xmit_size += chunk;
+out_write_wakeup:
+	uart_write_wakeup(uport);
+}
+
+static irqreturn_t qcom_geni_serial_isr(int isr, void *dev)
+{
+	unsigned int m_irq_status;
+	unsigned int s_irq_status;
+	struct uart_port *uport = dev;
+	unsigned long flags;
+	unsigned int m_irq_en;
+	bool drop_rx = false;
+	struct tty_port *tport = &uport->state->port;
+	struct qcom_geni_serial_port *port = to_dev_port(uport, uport);
+
+	if (uport->suspended)
+		return IRQ_HANDLED;
+
+	spin_lock_irqsave(&uport->lock, flags);
+	m_irq_status = readl_relaxed(uport->membase + SE_GENI_M_IRQ_STATUS);
+	s_irq_status = readl_relaxed(uport->membase + SE_GENI_S_IRQ_STATUS);
+	m_irq_en = readl_relaxed(uport->membase + SE_GENI_M_IRQ_EN);
+	writel_relaxed(m_irq_status, uport->membase + SE_GENI_M_IRQ_CLEAR);
+	writel_relaxed(s_irq_status, uport->membase + SE_GENI_S_IRQ_CLEAR);
+
+	if (WARN_ON(m_irq_status & M_ILLEGAL_CMD_EN))
+		goto out_unlock;
+
+	if (s_irq_status & S_RX_FIFO_WR_ERR_EN) {
+		uport->icount.overrun++;
+		tty_insert_flip_char(tport, 0, TTY_OVERRUN);
+	}
+
+	if (m_irq_status & (M_TX_FIFO_WATERMARK_EN | M_CMD_DONE_EN) &&
+	    m_irq_en & (M_TX_FIFO_WATERMARK_EN | M_CMD_DONE_EN))
+		qcom_geni_serial_handle_tx(uport);
+
+	if (s_irq_status & S_GP_IRQ_0_EN || s_irq_status & S_GP_IRQ_1_EN) {
+		if (s_irq_status & S_GP_IRQ_0_EN)
+			uport->icount.parity++;
+		drop_rx = true;
+	} else if (s_irq_status & S_GP_IRQ_2_EN ||
+					s_irq_status & S_GP_IRQ_3_EN) {
+		uport->icount.brk++;
+		port->brk = true;
+	}
+
+	if (s_irq_status & S_RX_FIFO_WATERMARK_EN ||
+					s_irq_status & S_RX_FIFO_LAST_EN)
+		qcom_geni_serial_handle_rx(uport, drop_rx);
+
+out_unlock:
+	spin_unlock_irqrestore(&uport->lock, flags);
+	return IRQ_HANDLED;
+}
+
+static int get_tx_fifo_size(struct qcom_geni_serial_port *port)
+{
+	struct uart_port *uport;
+
+	if (!port)
+		return -ENODEV;
+
+	uport = &port->uport;
+	port->tx_fifo_depth = geni_se_get_tx_fifo_depth(&port->se);
+	port->tx_fifo_width = geni_se_get_tx_fifo_width(&port->se);
+	port->rx_fifo_depth = geni_se_get_rx_fifo_depth(&port->se);
+	uport->fifosize =
+		(port->tx_fifo_depth * port->tx_fifo_width) / BITS_PER_BYTE;
+	return 0;
+}
+
+static void set_rfr_wm(struct qcom_geni_serial_port *port)
+{
+	/*
+	 * Set RFR (Flow off) to FIFO_DEPTH - 2.
+	 * RX WM level at 10% RX_FIFO_DEPTH.
+	 * TX WM level at 10% TX_FIFO_DEPTH.
+	 */
+	port->rx_rfr = port->rx_fifo_depth - 2;
+	port->rx_wm = UART_CONSOLE_RX_WM;
+	port->tx_wm = DEF_TX_WM;
+}
+
+static void qcom_geni_serial_shutdown(struct uart_port *uport)
+{
+	unsigned long flags;
+
+	/* Stop the console before stopping the current tx */
+	console_stop(uport->cons);
+
+	disable_irq(uport->irq);
+	free_irq(uport->irq, uport);
+	spin_lock_irqsave(&uport->lock, flags);
+	qcom_geni_serial_stop_tx(uport);
+	qcom_geni_serial_stop_rx(uport);
+	spin_unlock_irqrestore(&uport->lock, flags);
+}
+
+static int qcom_geni_serial_port_setup(struct uart_port *uport)
+{
+	struct qcom_geni_serial_port *port = to_dev_port(uport, uport);
+	unsigned int rxstale = DEFAULT_BITS_PER_CHAR * STALE_TIMEOUT;
+
+	set_rfr_wm(port);
+	writel_relaxed(rxstale, uport->membase + SE_UART_RX_STALE_CNT);
+	/*
+	 * Make an unconditional cancel on the main sequencer to reset
+	 * it else we could end up in data loss scenarios.
+	 */
+	port->xfer_mode = GENI_SE_FIFO;
+	qcom_geni_serial_poll_tx_done(uport);
+	geni_se_config_packing(&port->se, BITS_PER_BYTE, port->tx_bytes_pw,
+						false, true, false);
+	geni_se_config_packing(&port->se, BITS_PER_BYTE, port->rx_bytes_pw,
+						false, false, true);
+	geni_se_init(&port->se, port->rx_wm, port->rx_rfr);
+	geni_se_select_mode(&port->se, port->xfer_mode);
+	port->setup = true;
+	return 0;
+}
+
+static int qcom_geni_serial_startup(struct uart_port *uport)
+{
+	int ret;
+	u32 proto;
+	struct qcom_geni_serial_port *port = to_dev_port(uport, uport);
+
+	scnprintf(port->name, sizeof(port->name),
+		  "qcom_serial_geni%d",	uport->line);
+
+	proto = geni_se_read_proto(&port->se);
+	if (proto != GENI_SE_UART) {
+		dev_err(uport->dev, "Invalid FW loaded, proto: %d\n", proto);
+		return -ENXIO;
+	}
+
+	get_tx_fifo_size(port);
+	if (!port->setup) {
+		ret = qcom_geni_serial_port_setup(uport);
+		if (ret)
+			return ret;
+	}
+
+	ret = request_irq(uport->irq, qcom_geni_serial_isr, IRQF_TRIGGER_HIGH,
+							port->name, uport);
+	if (ret)
+		dev_err(uport->dev, "Failed to get IRQ ret %d\n", ret);
+	return ret;
+}
+
+static unsigned long get_clk_cfg(unsigned long clk_freq)
+{
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(root_freq); i++) {
+		if (!(root_freq[i] % clk_freq))
+			return root_freq[i];
+	}
+	return 0;
+}
+
+static unsigned long get_clk_div_rate(unsigned int baud, unsigned int *clk_div)
+{
+	unsigned long ser_clk;
+	unsigned long desired_clk;
+
+	desired_clk = baud * UART_OVERSAMPLING;
+	ser_clk = get_clk_cfg(desired_clk);
+	if (!ser_clk) {
+		pr_err("%s: Can't find matching DFS entry for baud %d\n",
+								__func__, baud);
+		return ser_clk;
+	}
+
+	*clk_div = ser_clk / desired_clk;
+	return ser_clk;
+}
+
+static void qcom_geni_serial_set_termios(struct uart_port *uport,
+				struct ktermios *termios, struct ktermios *old)
+{
+	unsigned int baud;
+	unsigned int bits_per_char;
+	unsigned int tx_trans_cfg;
+	unsigned int tx_parity_cfg;
+	unsigned int rx_trans_cfg;
+	unsigned int rx_parity_cfg;
+	unsigned int stop_bit_len;
+	unsigned int clk_div;
+	unsigned long ser_clk_cfg;
+	struct qcom_geni_serial_port *port = to_dev_port(uport, uport);
+	unsigned long clk_rate;
+
+	qcom_geni_serial_stop_rx(uport);
+	/* baud rate */
+	baud = uart_get_baud_rate(uport, termios, old, 300, 4000000);
+	port->baud = baud;
+	clk_rate = get_clk_div_rate(baud, &clk_div);
+	if (!clk_rate)
+		goto out_restart_rx;
+
+	uport->uartclk = clk_rate;
+	clk_set_rate(port->se.clk, clk_rate);
+	ser_clk_cfg = SER_CLK_EN;
+	ser_clk_cfg |= clk_div << CLK_DIV_SHFT;
+
+	/* parity */
+	tx_trans_cfg = readl_relaxed(uport->membase + SE_UART_TX_TRANS_CFG);
+	tx_parity_cfg = readl_relaxed(uport->membase + SE_UART_TX_PARITY_CFG);
+	rx_trans_cfg = readl_relaxed(uport->membase + SE_UART_RX_TRANS_CFG);
+	rx_parity_cfg = readl_relaxed(uport->membase + SE_UART_RX_PARITY_CFG);
+	if (termios->c_cflag & PARENB) {
+		tx_trans_cfg |= UART_TX_PAR_EN;
+		rx_trans_cfg |= UART_RX_PAR_EN;
+		tx_parity_cfg |= PAR_CALC_EN;
+		rx_parity_cfg |= PAR_CALC_EN;
+		if (termios->c_cflag & PARODD) {
+			tx_parity_cfg |= PAR_ODD;
+			rx_parity_cfg |= PAR_ODD;
+		} else if (termios->c_cflag & CMSPAR) {
+			tx_parity_cfg |= PAR_SPACE;
+			rx_parity_cfg |= PAR_SPACE;
+		} else {
+			tx_parity_cfg |= PAR_EVEN;
+			rx_parity_cfg |= PAR_EVEN;
+		}
+	} else {
+		tx_trans_cfg &= ~UART_TX_PAR_EN;
+		rx_trans_cfg &= ~UART_RX_PAR_EN;
+		tx_parity_cfg &= ~PAR_CALC_EN;
+		rx_parity_cfg &= ~PAR_CALC_EN;
+	}
+
+	/* bits per char */
+	switch (termios->c_cflag & CSIZE) {
+	case CS5:
+		bits_per_char = 5;
+		break;
+	case CS6:
+		bits_per_char = 6;
+		break;
+	case CS7:
+		bits_per_char = 7;
+		break;
+	case CS8:
+	default:
+		bits_per_char = 8;
+		break;
+	}
+
+	/* stop bits */
+	if (termios->c_cflag & CSTOPB)
+		stop_bit_len = TX_STOP_BIT_LEN_2;
+	else
+		stop_bit_len = TX_STOP_BIT_LEN_1;
+
+	/* flow control, clear the CTS_MASK bit if using flow control. */
+	if (termios->c_cflag & CRTSCTS)
+		tx_trans_cfg &= ~UART_CTS_MASK;
+	else
+		tx_trans_cfg |= UART_CTS_MASK;
+
+	if (baud)
+		uart_update_timeout(uport, termios->c_cflag, baud);
+
+	writel_relaxed(tx_trans_cfg, uport->membase + SE_UART_TX_TRANS_CFG);
+	writel_relaxed(tx_parity_cfg, uport->membase + SE_UART_TX_PARITY_CFG);
+	writel_relaxed(rx_trans_cfg, uport->membase + SE_UART_RX_TRANS_CFG);
+	writel_relaxed(rx_parity_cfg, uport->membase + SE_UART_RX_PARITY_CFG);
+	writel_relaxed(bits_per_char, uport->membase + SE_UART_TX_WORD_LEN);
+	writel_relaxed(bits_per_char, uport->membase + SE_UART_RX_WORD_LEN);
+	writel_relaxed(stop_bit_len, uport->membase + SE_UART_TX_STOP_BIT_LEN);
+	writel_relaxed(ser_clk_cfg, uport->membase + GENI_SER_M_CLK_CFG);
+	writel_relaxed(ser_clk_cfg, uport->membase + GENI_SER_S_CLK_CFG);
+out_restart_rx:
+	qcom_geni_serial_start_rx(uport);
+}
+
+static unsigned int qcom_geni_serial_tx_empty(struct uart_port *uport)
+{
+	return !readl_relaxed(uport->membase + SE_GENI_TX_FIFO_STATUS);
+}
+
+#ifdef CONFIG_SERIAL_QCOM_GENI_CONSOLE
+static int __init qcom_geni_console_setup(struct console *co, char *options)
+{
+	struct uart_port *uport;
+	struct qcom_geni_serial_port *port;
+	int baud;
+	int bits = 8;
+	int parity = 'n';
+	int flow = 'n';
+
+	if (co->index >= GENI_UART_CONS_PORTS  || co->index < 0)
+		return -ENXIO;
+
+	port = get_port_from_line(co->index);
+	if (IS_ERR(port)) {
+		pr_err("Invalid line %d(%d)\n", co->index, (int)PTR_ERR(port));
+		return PTR_ERR(port);
+	}
+
+	uport = &port->uport;
+
+	if (unlikely(!uport->membase))
+		return -ENXIO;
+
+	if (geni_se_resources_on(&port->se)) {
+		dev_err(port->se.dev, "Error turning on resources\n");
+		return -ENXIO;
+	}
+
+	if (unlikely(geni_se_read_proto(&port->se) != GENI_SE_UART)) {
+		geni_se_resources_off(&port->se);
+		return -ENXIO;
+	}
+
+	if (!port->setup) {
+		port->tx_bytes_pw = 1;
+		port->rx_bytes_pw = RX_BYTES_PW;
+		qcom_geni_serial_stop_rx(uport);
+		qcom_geni_serial_port_setup(uport);
+	}
+
+	if (options)
+		uart_parse_options(options, &baud, &parity, &bits, &flow);
+
+	return uart_set_options(uport, co, baud, parity, bits, flow);
+}
+
+static int __init console_register(struct uart_driver *drv)
+{
+	return uart_register_driver(drv);
+}
+
+static void console_unregister(struct uart_driver *drv)
+{
+	uart_unregister_driver(drv);
+}
+
+static struct console cons_ops = {
+	.name = "ttyMSM",
+	.write = qcom_geni_serial_console_write,
+	.device = uart_console_device,
+	.setup = qcom_geni_console_setup,
+	.flags = CON_PRINTBUFFER,
+	.index = -1,
+	.data = &qcom_geni_console_driver,
+};
+
+static struct uart_driver qcom_geni_console_driver = {
+	.owner = THIS_MODULE,
+	.driver_name = "qcom_geni_console",
+	.dev_name = "ttyMSM",
+	.nr =  GENI_UART_CONS_PORTS,
+	.cons = &cons_ops,
+};
+#else
+static int console_register(struct uart_driver *drv)
+{
+	return 0;
+}
+
+static void console_unregister(struct uart_driver *drv)
+{
+}
+#endif /* CONFIG_SERIAL_QCOM_GENI_CONSOLE */
+
+static void qcom_geni_serial_cons_pm(struct uart_port *uport,
+		unsigned int new_state, unsigned int old_state)
+{
+	struct qcom_geni_serial_port *port = to_dev_port(uport, uport);
+
+	if (unlikely(!uart_console(uport)))
+		return;
+
+	if (new_state == UART_PM_STATE_ON && old_state == UART_PM_STATE_OFF)
+		geni_se_resources_on(&port->se);
+	else if (new_state == UART_PM_STATE_OFF &&
+			old_state == UART_PM_STATE_ON)
+		geni_se_resources_off(&port->se);
+}
+
+static const struct uart_ops qcom_geni_console_pops = {
+	.tx_empty = qcom_geni_serial_tx_empty,
+	.stop_tx = qcom_geni_serial_stop_tx,
+	.start_tx = qcom_geni_serial_start_tx,
+	.stop_rx = qcom_geni_serial_stop_rx,
+	.set_termios = qcom_geni_serial_set_termios,
+	.startup = qcom_geni_serial_startup,
+	.request_port = qcom_geni_serial_request_port,
+	.config_port = qcom_geni_serial_config_port,
+	.shutdown = qcom_geni_serial_shutdown,
+	.type = qcom_geni_serial_get_type,
+	.set_mctrl = qcom_geni_cons_set_mctrl,
+	.get_mctrl = qcom_geni_cons_get_mctrl,
+#ifdef CONFIG_CONSOLE_POLL
+	.poll_get_char	= qcom_geni_serial_get_char,
+	.poll_put_char	= qcom_geni_serial_poll_put_char,
+#endif
+	.pm = qcom_geni_serial_cons_pm,
+};
+
+static int qcom_geni_serial_probe(struct platform_device *pdev)
+{
+	int ret = 0;
+	int line = -1;
+	struct qcom_geni_serial_port *port;
+	struct uart_port *uport;
+	struct resource *res;
+
+	if (pdev->dev.of_node)
+		line = of_alias_get_id(pdev->dev.of_node, "serial");
+	else
+		line = pdev->id;
+
+	if (line < 0 || line >= GENI_UART_CONS_PORTS)
+		return -ENXIO;
+	port = get_port_from_line(line);
+	if (IS_ERR(port)) {
+		ret = PTR_ERR(port);
+		dev_err(&pdev->dev, "Invalid line %d(%d)\n", line, ret);
+		return ret;
+	}
+
+	uport = &port->uport;
+	/* Don't allow 2 drivers to access the same port */
+	if (uport->private_data)
+		return -ENODEV;
+
+	uport->dev = &pdev->dev;
+	port->se.dev = &pdev->dev;
+	port->se.wrapper = dev_get_drvdata(pdev->dev.parent);
+	port->se.clk = devm_clk_get(&pdev->dev, "se");
+	if (IS_ERR(port->se.clk)) {
+		ret = PTR_ERR(port->se.clk);
+		dev_err(&pdev->dev, "Err getting SE Core clk %d\n", ret);
+		return ret;
+	}
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (IS_ERR(res))
+		return PTR_ERR(res);
+	uport->mapbase = res->start;
+
+	port->tx_fifo_depth = DEF_FIFO_DEPTH_WORDS;
+	port->rx_fifo_depth = DEF_FIFO_DEPTH_WORDS;
+	port->tx_fifo_width = DEF_FIFO_WIDTH_BITS;
+
+	uport->irq = platform_get_irq(pdev, 0);
+	if (uport->irq < 0) {
+		dev_err(&pdev->dev, "Failed to get IRQ %d\n", uport->irq);
+		return uport->irq;
+	}
+
+	uport->private_data = &qcom_geni_console_driver;
+	platform_set_drvdata(pdev, port);
+	port->handle_rx = handle_rx_console;
+	port->setup = false;
+	return uart_add_one_port(&qcom_geni_console_driver, uport);
+}
+
+static int qcom_geni_serial_remove(struct platform_device *pdev)
+{
+	struct qcom_geni_serial_port *port = platform_get_drvdata(pdev);
+	struct uart_driver *drv = port->uport.private_data;
+
+	uart_remove_one_port(drv, &port->uport);
+	return 0;
+}
+
+static int __maybe_unused qcom_geni_serial_sys_suspend_noirq(struct device *dev)
+{
+	struct platform_device *pdev = to_platform_device(dev);
+	struct qcom_geni_serial_port *port = platform_get_drvdata(pdev);
+	struct uart_port *uport = &port->uport;
+
+	uart_suspend_port(uport->private_data, uport);
+	return 0;
+}
+
+static int __maybe_unused qcom_geni_serial_sys_resume_noirq(struct device *dev)
+{
+	struct platform_device *pdev = to_platform_device(dev);
+	struct qcom_geni_serial_port *port = platform_get_drvdata(pdev);
+	struct uart_port *uport = &port->uport;
+
+	if (console_suspend_enabled && uport->suspended) {
+		uart_resume_port(uport->private_data, uport);
+		disable_irq(uport->irq);
+	}
+	return 0;
+}
+
+static const struct dev_pm_ops qcom_geni_serial_pm_ops = {
+	SET_NOIRQ_SYSTEM_SLEEP_PM_OPS(qcom_geni_serial_sys_suspend_noirq,
+					qcom_geni_serial_sys_resume_noirq)
+};
+
+static const struct of_device_id qcom_geni_serial_match_table[] = {
+	{ .compatible = "qcom,geni-debug-uart", },
+	{}
+};
+MODULE_DEVICE_TABLE(of, qcom_geni_serial_match_table);
+
+static struct platform_driver qcom_geni_serial_platform_driver = {
+	.remove = qcom_geni_serial_remove,
+	.probe = qcom_geni_serial_probe,
+	.driver = {
+		.name = "qcom_geni_serial",
+		.of_match_table = qcom_geni_serial_match_table,
+		.pm = &qcom_geni_serial_pm_ops,
+	},
+};
+
+static int __init qcom_geni_serial_init(void)
+{
+	int ret;
+
+	qcom_geni_console_port.uport.iotype = UPIO_MEM;
+	qcom_geni_console_port.uport.ops = &qcom_geni_console_pops;
+	qcom_geni_console_port.uport.flags = UPF_BOOT_AUTOCONF;
+	qcom_geni_console_port.uport.line = 0;
+
+	ret = console_register(&qcom_geni_console_driver);
+	if (ret)
+		return ret;
+
+	ret = platform_driver_register(&qcom_geni_serial_platform_driver);
+	if (ret)
+		console_unregister(&qcom_geni_console_driver);
+	return ret;
+}
+module_init(qcom_geni_serial_init);
+
+static void __exit qcom_geni_serial_exit(void)
+{
+	platform_driver_unregister(&qcom_geni_serial_platform_driver);
+	console_unregister(&qcom_geni_console_driver);
+}
+module_exit(qcom_geni_serial_exit);
+
+MODULE_DESCRIPTION("Serial driver for GENI based QUP cores");
+MODULE_LICENSE("GPL v2");
-- 
Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project

--
To unsubscribe from this list: send the line "unsubscribe linux-doc" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html