Re: [lm-sensors] dme1737 module

[Juergen Bausa <Juergen.Bausa@web.de>]

> -----Ursprüngliche Nachricht-----
> Von: "Juerg Haefliger" <juergh@gmail.com>
> Gesendet: 28.08.07 17:07:38
> An: "Juergen Bausa" <Juergen.Bausa@web.de>
> CC: "Kushal Koolwal" <kushalkoolwal@hotmail.com>, lm-sensors@lm-sensors.org
> Betreff: Re: [lm-sensors] dme1737 module


> 
> 
> > So, which version is needed to run the dme1737 on the asus board (Which I think doesnt have the
> > SCH3114 Super I/O chip)?
> >
> > debian testing and unstable both have 2.10.4 at the moment, which is the same version as
> > http://www.lm-sensors.org/wiki/Download. Will it be enough to install this version?
> 
> 2.10.4 and kernel 2.6.23 is sufficient if you don't have the sch311x.
> 

Now it works with lm-sensors 2.10.4 which can easily backported drom debian testing.

However, I get strange temperatures for the cpu. With the fan at 3000 rpm and idle cpu I get a temperature
of 17 °C, while room temperature is 20°C. I think this is not possible. 

I now use fancontrol which turns fan speed to 0 rpm. Here is the output of sensors:

dme1737-i2c-0-2e
Adapter: SMBus nForce2 adapter at 4c00
V5stby:    +0.00 V  (min =  +0.00 V, max =  +6.64 V)  ALARM
Vccp:      +1.10 V  (min =  +0.00 V, max =  +2.99 V)
V3.3:      +3.28 V  (min =  +0.00 V, max =  +4.38 V)
V5:        +4.94 V  (min =  +0.00 V, max =  +6.64 V)
V12:      +11.80 V  (min =  +0.00 V, max = +15.94 V)
V3.3stby:  +3.29 V  (min =  +0.00 V, max =  +4.38 V)
Vbat:      +2.98 V  (min =  +0.00 V, max =  +4.38 V)
Int Temp:    +34°C  (low  =  -127°C, high =  +127°C)
CPU Temp:    +29°C  (low  =  -127°C, high =  +127°C)
CPU_Fan:     0 RPM  (min =    0 RPM)
ERROR: Can't get fan3 data!
ERROR: Can't get fan5 data!
ERROR: Can't get fan6 data!
CPU_PWM:     0      (enable = 1, freq =  25000 Hz)
ERROR: Can't get pwm5 data!
ERROR: Can't get pwm6 data!
cpu0_vid: +1.550 V  (VRM Version 2.4)

I think 29 °C is also very low for idle and no fan, even for my AMD BE-2350 
(45 w maximum power consumption). Also, Int-Temperature (is this board temperature?)
is higher than cpu- temperature. This changes only for high load, where
cpu-temperature increases more than int-temperature.

At first I thought that temperature calculation is wrong in lm-sensors. However,
BIOS shows nearly the same temperatures.

So, is there anything wrong here?

Juergen
_________________________________________________________________________
In 5 Schritten zur eigenen Homepage. Jetzt Domain sichern und gestalten! 
Nur 3,99 EUR/Monat! http://www.maildomain.web.de/?mc\x021114


_______________________________________________
lm-sensors mailing list
lm-sensors@lm-sensors.org
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors