Re: [PATCH v8 6/7] arm64: dts: add dts nodes for MT6779

[Hanks Chen <hanks.chen@mediatek.com>]

On Tue, 2020-07-14 at 20:14 +0200, Matthias Brugger wrote:
> 
> On 14/07/2020 11:20, Hanks Chen wrote:
> > this adds initial MT6779 dts settings for board support,
> > including cpu, gic, timer, ccf, pinctrl, uart, sysirq...etc.
> > 
> > Signed-off-by: Hanks Chen <hanks.chen@mediatek.com>
> > ---
> >   arch/arm64/boot/dts/mediatek/Makefile       |   1 +
> >   arch/arm64/boot/dts/mediatek/mt6779-evb.dts |  31 +++
> >   arch/arm64/boot/dts/mediatek/mt6779.dtsi    | 271 ++++++++++++++++++++
> >   3 files changed, 303 insertions(+)
> >   create mode 100644 arch/arm64/boot/dts/mediatek/mt6779-evb.dts
> >   create mode 100644 arch/arm64/boot/dts/mediatek/mt6779.dtsi
> > 
> [...]
> > +
> > +		uart0: serial@11002000 {
> > +			compatible = "mediatek,mt6779-uart",
> > +				     "mediatek,mt6577-uart";
> > +			reg = <0 0x11002000 0 0x400>;
> > +			interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>;
> > +			clocks = <&clk26m>, <&infracfg_ao CLK_INFRA_UART0>;
> > +			clock-names = "baud", "bus";
> > +			status = "disabled";
> > +		};
> > +
> > +		uart1: serial@11003000 {
> > +			compatible = "mediatek,mt6779-uart",
> > +				     "mediatek,mt6577-uart";
> > +			reg = <0 0x11003000 0 0x400>;
> > +			interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_LOW>;
> > +			clocks = <&clk26m>, <&infracfg_ao CLK_INFRA_UART1>;
> > +			clock-names = "baud", "bus";
> > +			status = "disabled";
> > +		};
> > +
> > +		uart2: serial@11004000 {
> > +			compatible = "mediatek,mt6779-uart",
> > +				     "mediatek,mt6577-uart";
> > +			reg = <0 0x11004000 0 0x400>;
> > +			interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_LOW>;
> > +			clocks = <&clk26m>, <&infracfg_ao CLK_INFRA_UART2>;
> > +			clock-names = "baud", "bus";
> > +			status = "disabled";
> > +		};
> 
> Devicetree describes the HW we have. As far as I know, we have 4 UARTs on 
> MT6779. So we should list them all here.
> 

Actually, We have only 3 UARTs HW on MT6779, but have 4 UART clk in
header file of clk.
CLK_INFRA_UART3 is a dummy clk interface, it has no effect on the
operation of the read/write instruction.

If you think it is not good, I can remove it in the header file of clk.

Thanks

> Regards,
> Matthias