Re: [PATCH v8 6/7] arm64: dts: add dts nodes for MT6779

[Matthias Brugger <matthias.bgg@gmail.com>]

On 16/07/2020 06:04, Hanks Chen wrote:
> On Tue, 2020-07-14 at 20:14 +0200, Matthias Brugger wrote:
>>
>> On 14/07/2020 11:20, Hanks Chen wrote:
>>> this adds initial MT6779 dts settings for board support,
>>> including cpu, gic, timer, ccf, pinctrl, uart, sysirq...etc.
>>>
>>> Signed-off-by: Hanks Chen <hanks.chen@mediatek.com>
>>> ---
>>>    arch/arm64/boot/dts/mediatek/Makefile       |   1 +
>>>    arch/arm64/boot/dts/mediatek/mt6779-evb.dts |  31 +++
>>>    arch/arm64/boot/dts/mediatek/mt6779.dtsi    | 271 ++++++++++++++++++++
>>>    3 files changed, 303 insertions(+)
>>>    create mode 100644 arch/arm64/boot/dts/mediatek/mt6779-evb.dts
>>>    create mode 100644 arch/arm64/boot/dts/mediatek/mt6779.dtsi
>>>
>> [...]
>>> +
>>> +		uart0: serial@11002000 {
>>> +			compatible = "mediatek,mt6779-uart",
>>> +				     "mediatek,mt6577-uart";
>>> +			reg = <0 0x11002000 0 0x400>;
>>> +			interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>;
>>> +			clocks = <&clk26m>, <&infracfg_ao CLK_INFRA_UART0>;
>>> +			clock-names = "baud", "bus";
>>> +			status = "disabled";
>>> +		};
>>> +
>>> +		uart1: serial@11003000 {
>>> +			compatible = "mediatek,mt6779-uart",
>>> +				     "mediatek,mt6577-uart";
>>> +			reg = <0 0x11003000 0 0x400>;
>>> +			interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_LOW>;
>>> +			clocks = <&clk26m>, <&infracfg_ao CLK_INFRA_UART1>;
>>> +			clock-names = "baud", "bus";
>>> +			status = "disabled";
>>> +		};
>>> +
>>> +		uart2: serial@11004000 {
>>> +			compatible = "mediatek,mt6779-uart",
>>> +				     "mediatek,mt6577-uart";
>>> +			reg = <0 0x11004000 0 0x400>;
>>> +			interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_LOW>;
>>> +			clocks = <&clk26m>, <&infracfg_ao CLK_INFRA_UART2>;
>>> +			clock-names = "baud", "bus";
>>> +			status = "disabled";
>>> +		};
>>
>> Devicetree describes the HW we have. As far as I know, we have 4 UARTs on
>> MT6779. So we should list them all here.
>>
> 
> Actually, We have only 3 UARTs HW on MT6779, but have 4 UART clk in
> header file of clk.

Correct, I got confused by the four clocks.
With that clarified I'm fine with the patch and will take it as soon as the 
clock driver patch is accepted.

Regards,
Matthias

> CLK_INFRA_UART3 is a dummy clk interface, it has no effect on the
> operation of the read/write instruction.
> 
> If you think it is not good, I can remove it in the header file of clk.
> 
> Thanks
> 
>> Regards,
>> Matthias
>