All of lore.kernel.org
 help / color / mirror / Atom feed
From: Maharaja Kennadyrajan <mkenna@codeaurora.org>
To: ath11k@lists.infradead.org, linux-wireless@vger.kernel.org
Cc: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Subject: [PATCH v4 3/3] ath11k: Add support for beacon tx mode
Date: Tue,  8 Jun 2021 20:37:35 +0530	[thread overview]
Message-ID: <1623164855-15910-4-git-send-email-mkenna@codeaurora.org> (raw)
In-Reply-To: <1623164855-15910-1-git-send-email-mkenna@codeaurora.org>

Add support to configure the beacon tx mode in
the driver.

Beacons can be sent out in burst(continuously in a single shot
one after another) or staggered (equally spread out over beacon
interval) mode.

Use the below configuration in the hostapd/wpa_supplicant
for AP/MESH mode to configure the beacon tx mode.

"beacon_tx_mode=N", where N = 1 for STAGGERED beacon mode
and N = 2 for BURST beacon mode.

Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-00480-QCAHKSWPL_SILICONZ-1

Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
---
 drivers/net/wireless/ath/ath11k/mac.c | 10 +++++++---
 1 file changed, 7 insertions(+), 3 deletions(-)

diff --git a/drivers/net/wireless/ath/ath11k/mac.c b/drivers/net/wireless/ath/ath11k/mac.c
index 9d0ff15..dfc8644 100644
--- a/drivers/net/wireless/ath/ath11k/mac.c
+++ b/drivers/net/wireless/ath/ath11k/mac.c
@@ -2130,7 +2130,10 @@ static void ath11k_mac_op_bss_info_changed(struct ieee80211_hw *hw,
 
 	if (changed & BSS_CHANGED_BEACON) {
 		param_id = WMI_PDEV_PARAM_BEACON_TX_MODE;
-		param_value = WMI_BEACON_STAGGERED_MODE;
+		if (info->beacon_tx_mode == NL80211_BEACON_BURST_MODE)
+			param_value = WMI_BEACON_BURST_MODE;
+		else
+			param_value = WMI_BEACON_STAGGERED_MODE;
 		ret = ath11k_wmi_pdev_set_param(ar, param_id,
 						param_value, ar->pdev->pdev_id);
 		if (ret)
@@ -2138,8 +2141,9 @@ static void ath11k_mac_op_bss_info_changed(struct ieee80211_hw *hw,
 				    arvif->vdev_id);
 		else
 			ath11k_dbg(ar->ab, ATH11K_DBG_MAC,
-				   "Set staggered beacon mode for VDEV: %d\n",
-				   arvif->vdev_id);
+				   "Set %s beacon mode for VDEV: %d mode: %d\n",
+				   param_value ? "burst" : "staggered",
+				   arvif->vdev_id, param_value);
 
 		ret = ath11k_mac_setup_bcn_tmpl(arvif);
 		if (ret)
-- 
2.7.4


-- 
ath11k mailing list
ath11k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath11k

WARNING: multiple messages have this Message-ID (diff)
From: Maharaja Kennadyrajan <mkenna@codeaurora.org>
To: ath11k@lists.infradead.org, linux-wireless@vger.kernel.org
Cc: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Subject: [PATCH v4 3/3] ath11k: Add support for beacon tx mode
Date: Tue,  8 Jun 2021 20:37:35 +0530	[thread overview]
Message-ID: <1623164855-15910-4-git-send-email-mkenna@codeaurora.org> (raw)
In-Reply-To: <1623164855-15910-1-git-send-email-mkenna@codeaurora.org>

Add support to configure the beacon tx mode in
the driver.

Beacons can be sent out in burst(continuously in a single shot
one after another) or staggered (equally spread out over beacon
interval) mode.

Use the below configuration in the hostapd/wpa_supplicant
for AP/MESH mode to configure the beacon tx mode.

"beacon_tx_mode=N", where N = 1 for STAGGERED beacon mode
and N = 2 for BURST beacon mode.

Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-00480-QCAHKSWPL_SILICONZ-1

Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
---
 drivers/net/wireless/ath/ath11k/mac.c | 10 +++++++---
 1 file changed, 7 insertions(+), 3 deletions(-)

diff --git a/drivers/net/wireless/ath/ath11k/mac.c b/drivers/net/wireless/ath/ath11k/mac.c
index 9d0ff15..dfc8644 100644
--- a/drivers/net/wireless/ath/ath11k/mac.c
+++ b/drivers/net/wireless/ath/ath11k/mac.c
@@ -2130,7 +2130,10 @@ static void ath11k_mac_op_bss_info_changed(struct ieee80211_hw *hw,
 
 	if (changed & BSS_CHANGED_BEACON) {
 		param_id = WMI_PDEV_PARAM_BEACON_TX_MODE;
-		param_value = WMI_BEACON_STAGGERED_MODE;
+		if (info->beacon_tx_mode == NL80211_BEACON_BURST_MODE)
+			param_value = WMI_BEACON_BURST_MODE;
+		else
+			param_value = WMI_BEACON_STAGGERED_MODE;
 		ret = ath11k_wmi_pdev_set_param(ar, param_id,
 						param_value, ar->pdev->pdev_id);
 		if (ret)
@@ -2138,8 +2141,9 @@ static void ath11k_mac_op_bss_info_changed(struct ieee80211_hw *hw,
 				    arvif->vdev_id);
 		else
 			ath11k_dbg(ar->ab, ATH11K_DBG_MAC,
-				   "Set staggered beacon mode for VDEV: %d\n",
-				   arvif->vdev_id);
+				   "Set %s beacon mode for VDEV: %d mode: %d\n",
+				   param_value ? "burst" : "staggered",
+				   arvif->vdev_id, param_value);
 
 		ret = ath11k_mac_setup_bcn_tmpl(arvif);
 		if (ret)
-- 
2.7.4


  parent reply	other threads:[~2021-06-08 15:08 UTC|newest]

Thread overview: 18+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2021-06-08 15:07 [PATCH v4 0/3] Add support to configure beacon tx mode Maharaja Kennadyrajan
2021-06-08 15:07 ` Maharaja Kennadyrajan
2021-06-08 15:07 ` [PATCH v4 1/3] nl80211: Add support for " Maharaja Kennadyrajan
2021-06-08 15:07   ` Maharaja Kennadyrajan
2021-06-23 11:16   ` Johannes Berg
2021-06-23 11:16     ` Johannes Berg
2021-06-29 17:44     ` Felix Fietkau
2021-06-29 17:44       ` Felix Fietkau
2021-08-10  8:32       ` Maharaja Kennadyrajan
2021-08-10  8:32         ` Maharaja Kennadyrajan
2021-08-10  8:31     ` Maharaja Kennadyrajan
2021-08-10  8:31       ` Maharaja Kennadyrajan
2021-06-08 15:07 ` [PATCH v4 2/3] mac80211: " Maharaja Kennadyrajan
2021-06-08 15:07   ` Maharaja Kennadyrajan
2021-06-08 15:07 ` Maharaja Kennadyrajan [this message]
2021-06-08 15:07   ` [PATCH v4 3/3] ath11k: " Maharaja Kennadyrajan
2021-06-08 21:41 ` [PATCH v4 0/3] Add support to configure " Jeff Johnson
2021-06-08 21:41   ` Jeff Johnson

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1623164855-15910-4-git-send-email-mkenna@codeaurora.org \
    --to=mkenna@codeaurora.org \
    --cc=ath11k@lists.infradead.org \
    --cc=linux-wireless@vger.kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.