RH 7.1 on IBM xSeries 240

All of lore.kernel.org
 help / color / mirror / Atom feed

* RH 7.1 on IBM xSeries 240
@ 2001-05-16 10:02 ps
  2001-05-16 16:57 ` Leah Cunningham
  2001-05-16 23:29 ` Alan Cox
  0 siblings, 2 replies; 8+ messages in thread
From: ps @ 2001-05-16 10:02 UTC (permalink / raw)
  To: linux-kernel

I'm trying to run Linux RH 7.1 on the rack-mounted 
IBM xSeries 240 with ServeRAID but without success.
I've tried some kernels from 2.2.19-7.0.1smp up to
2.4.3-2.14.14.i686 and 2.4.4.

During boot all kernels reported errors (attached at the end).
When I try to write to disk (untar 100MB) machine almost hangs -
I must wait MINUTES for any simple "ll" or "who".

Thanks in advance for any help.

 - Piotr Szymanek

=================================================
   ...

found SMP MP-table at 0009e140
hm, page 0009e000 reserved twice.
hm, page 0009f000 reserved twice.
hm, page 000a0000 reserved twice.
hm, page 0009e000 reserved twice.
hm, page 0009f000 reserved twice.
hm, page 000a0000 reserved twice.
WARNING: MP table in the EBDA can be UNSAFE

   ...

ENABLING IO-APIC IRQs
...changing IO-APIC physical APIC ID to 14 ... ok.
BIOS bug, IO-APIC#1 ID is 15 in the MPC table!...
... fixing up to 15. (tell your hw vendor)
...changing IO-APIC physical APIC ID to 15 ... ok.
Synchronizing Arb IDs.
init IO_APIC IRQs
 IO-APIC (apicid-pin) 14-0, 14-5, 15-0, 15-1, 15-2, 15-3, 15-14, 15-15
not connected.
..TIMER: vector=49 pin1=2 pin2=0
..MP-BIOS bug: 8254 timer not connected to IO-APIC
...trying to set up timer (IRQ0) through the 8259A ... 
..... (found pin 0) ...works.
number of MP IRQ sources: 31.
number of IO-APIC #14 registers: 16.
number of IO-APIC #15 registers: 16.
testing the IO APIC.......................

   ...

CPU1<T0:1332736,T1:444240,D:6,S:444245,C:1332737>
checking TSC synchronization across CPUs: passed.
Setting commenced=1, go go go
mtrr: your CPUs had inconsistent fixed MTRR settings
mtrr: probably your BIOS does not setup all CPUs
PCI: PCI BIOS revision 2.10 entry at 0xfd34c, last bus=4

^ permalink raw reply	[flat|nested] 8+ messages in thread

* Re: RH 7.1 on IBM xSeries 240
  2001-05-16 10:02 RH 7.1 on IBM xSeries 240 ps
@ 2001-05-16 16:57 ` Leah Cunningham
  2001-05-16 17:29   ` ps
  2001-05-16 23:29 ` Alan Cox
  1 sibling, 1 reply; 8+ messages in thread
From: Leah Cunningham @ 2001-05-16 16:57 UTC (permalink / raw)
  To: ps; +Cc: linux-kernel

This may be way off, but have you flashed the BIOS to the most
current revision? This machine should work properly.  How many
processors and what SR card are you using?

ps (ps@rzeczpospolita.pl) [010516 03:07]:
- > I'm trying to run Linux RH 7.1 on the rack-mounted 
- > IBM xSeries 240 with ServeRAID but without success.
- > I've tried some kernels from 2.2.19-7.0.1smp up to
- > 2.4.3-2.14.14.i686 and 2.4.4.
- > 
- > During boot all kernels reported errors (attached at the end).
- > When I try to write to disk (untar 100MB) machine almost hangs -
- > I must wait MINUTES for any simple "ll" or "who".
- > 
- > Thanks in advance for any help.
- > 
- >  - Piotr Szymanek
- > 
- > =================================================
- >    ...
- > 
- > found SMP MP-table at 0009e140
- > hm, page 0009e000 reserved twice.
- > hm, page 0009f000 reserved twice.
- > hm, page 000a0000 reserved twice.
- > hm, page 0009e000 reserved twice.
- > hm, page 0009f000 reserved twice.
- > hm, page 000a0000 reserved twice.
- > WARNING: MP table in the EBDA can be UNSAFE
- > 
- >    ...
- > 
- > ENABLING IO-APIC IRQs
- > ...changing IO-APIC physical APIC ID to 14 ... ok.
- > BIOS bug, IO-APIC#1 ID is 15 in the MPC table!...
- > ... fixing up to 15. (tell your hw vendor)
- > ...changing IO-APIC physical APIC ID to 15 ... ok.
- > Synchronizing Arb IDs.
- > init IO_APIC IRQs
- >  IO-APIC (apicid-pin) 14-0, 14-5, 15-0, 15-1, 15-2, 15-3, 15-14, 15-15
- > not connected.
- > ..TIMER: vector=49 pin1=2 pin2=0
- > ..MP-BIOS bug: 8254 timer not connected to IO-APIC
- > ...trying to set up timer (IRQ0) through the 8259A ... 
- > ..... (found pin 0) ...works.
- > number of MP IRQ sources: 31.
- > number of IO-APIC #14 registers: 16.
- > number of IO-APIC #15 registers: 16.
- > testing the IO APIC.......................
- > 
- >    ...
- > 
- > CPU1<T0:1332736,T1:444240,D:6,S:444245,C:1332737>
- > checking TSC synchronization across CPUs: passed.
- > Setting commenced=1, go go go
- > mtrr: your CPUs had inconsistent fixed MTRR settings
- > mtrr: probably your BIOS does not setup all CPUs
- > PCI: PCI BIOS revision 2.10 entry at 0xfd34c, last bus=4
- > -
- > To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
- > the body of a message to majordomo@vger.kernel.org
- > More majordomo info at  http://vger.kernel.org/majordomo-info.html
- > Please read the FAQ at  http://www.tux.org/lkml/

             I can't believe it's not UNIX!!!
------------------------------------------------------------
Leah Cunningham             |  SuSE Expert, NOS Engineer, 
Undisclosed Address         |  QA & Linux geek, et al.        

^ permalink raw reply	[flat|nested] 8+ messages in thread

* Re: RH 7.1 on IBM xSeries 240
  2001-05-16 16:57 ` Leah Cunningham
@ 2001-05-16 17:29   ` ps
  2001-05-16 17:49     ` Leah Cunningham
  0 siblings, 1 reply; 8+ messages in thread
From: ps @ 2001-05-16 17:29 UTC (permalink / raw)
  To: Leah Cunningham; +Cc: linux-kernel

Yes, I have the newest BIOS and SR Firmware.
I have 2 x 1GHz CPUs and IBM PCI ServeRAID 4.71.00  <ServeRAID 4L>

  --  Piotr Szymanek


Leah Cunningham wrote:
> 
> This may be way off, but have you flashed the BIOS to the most
> current revision? This machine should work properly.  How many
> processors and what SR card are you using?

^ permalink raw reply	[flat|nested] 8+ messages in thread

* Re: RH 7.1 on IBM xSeries 240
  2001-05-16 17:29   ` ps
@ 2001-05-16 17:49     ` Leah Cunningham
  0 siblings, 0 replies; 8+ messages in thread
From: Leah Cunningham @ 2001-05-16 17:49 UTC (permalink / raw)
  To: ps; +Cc: linux-kernel

Well, if you want I can try and reproduce your issue once I have
access to this machine.  It may be about a week or so.  RH 7.1 has
been tested on this machine, but not with ServeRaid 4.71. 

ps (ps@rzeczpospolita.pl) [010516 10:29]:
- > Yes, I have the newest BIOS and SR Firmware.
- > I have 2 x 1GHz CPUs and IBM PCI ServeRAID 4.71.00  <ServeRAID 4L>
- > 
- >   --  Piotr Szymanek
- > 
- > 
- > Leah Cunningham wrote:
- > > 
- > > This may be way off, but have you flashed the BIOS to the most
- > > current revision? This machine should work properly.  How many
- > > processors and what SR card are you using?

             I can't believe it's not UNIX!!!
------------------------------------------------------------
Leah Cunningham             |  SuSE Expert, NOS Engineer, 
Undisclosed Address         |  QA & Linux geek, et al.        

^ permalink raw reply	[flat|nested] 8+ messages in thread

* Re: RH 7.1 on IBM xSeries 240
  2001-05-16 10:02 RH 7.1 on IBM xSeries 240 ps
  2001-05-16 16:57 ` Leah Cunningham
@ 2001-05-16 23:29 ` Alan Cox
  1 sibling, 0 replies; 8+ messages in thread
From: Alan Cox @ 2001-05-16 23:29 UTC (permalink / raw)
  To: ps; +Cc: linux-kernel

> hm, page 0009f000 reserved twice.
> hm, page 000a0000 reserved twice.
> WARNING: MP table in the EBDA can be UNSAFE

These are ok...

> ENABLING IO-APIC IRQs
> ...changing IO-APIC physical APIC ID to 14 ... ok.
> BIOS bug, IO-APIC#1 ID is 15 in the MPC table!...
> ... fixing up to 15. (tell your hw vendor)

Your BIOS tables seemed wrong..

> mtrr: your CPUs had inconsistent fixed MTRR settings
> mtrr: probably your BIOS does not setup all CPUs

And your BIOS fails to set up the MTRR's properly. These are real BIOS 
mistakes. They are ones Linux however took corrective action on.

^ permalink raw reply	[flat|nested] 8+ messages in thread

[parent not found: <fa.fhhq4kv.gguq9t@ifi.uio.no>]

[parent not found: <fa.fuo78ov.ikad9g@ifi.uio.no>]

* Re: RH 7.1 on IBM xSeries 240
       [not found] ` <fa.fuo78ov.ikad9g@ifi.uio.no>
@ 2001-05-17  9:48   ` Pim Zandbergen
  2001-05-17 10:30     ` ps
  0 siblings, 1 reply; 8+ messages in thread
From: Pim Zandbergen @ 2001-05-17  9:48 UTC (permalink / raw)
  To: ps; +Cc: linux-kernel

>Yes, I have the newest BIOS and SR Firmware.
>I have 2 x 1GHz CPUs and IBM PCI ServeRAID 4.71.00  <ServeRAID 4L>

You mean all of BIOS, firmware and Linux driver are at version 4.71?

Where did you find BIOS 4.71 and firmware 4.71?
The latest BIOS & firmware I could find is 4.50.

There is, however a driver version 4.72 in the latest 2.4.4-ac
kernels.

Pim

^ permalink raw reply	[flat|nested] 8+ messages in thread

* Re: RH 7.1 on IBM xSeries 240
  2001-05-17  9:48   ` Pim Zandbergen
@ 2001-05-17 10:30     ` ps
  2001-05-17 14:28       ` Leah Cunningham
  0 siblings, 1 reply; 8+ messages in thread
From: ps @ 2001-05-17 10:30 UTC (permalink / raw)
  To: Pim Zandbergen; +Cc: linux-kernel

Pim Zandbergen wrote:
> 
> >Yes, I have the newest BIOS and SR Firmware.
> >I have 2 x 1GHz CPUs and IBM PCI ServeRAID 4.71.00  <ServeRAID 4L>
> 
> You mean all of BIOS, firmware and Linux driver are at version 4.71?
> 
> Where did you find BIOS 4.71 and firmware 4.71?
> The latest BIOS & firmware I could find is 4.50.

Firmware is 4.70.17, I'v got it directly from IBM engineer.
Previous firmware (2 days ago) was really 4.50 but it performed worse
(was less stable in performance).

> There is, however a driver version 4.72 in the latest 2.4.4-ac
> kernels.

I've tried it but it was all the same - I came back to 4.71

^ permalink raw reply	[flat|nested] 8+ messages in thread

* Re: RH 7.1 on IBM xSeries 240
  2001-05-17 10:30     ` ps
@ 2001-05-17 14:28       ` Leah Cunningham
  0 siblings, 0 replies; 8+ messages in thread
From: Leah Cunningham @ 2001-05-17 14:28 UTC (permalink / raw)
  To: ps; +Cc: Pim Zandbergen, linux-kernel

- > > >Yes, I have the newest BIOS and SR Firmware.
- > > >I have 2 x 1GHz CPUs and IBM PCI ServeRAID 4.71.00  <ServeRAID 4L>
- > 
- > Firmware is 4.70.17, I'v got it directly from IBM engineer.
- > Previous firmware (2 days ago) was really 4.50 but it performed worse
- > (was less stable in performance).

That makes a bit more sense.  This code is stil in test, however.
Previously you said 4.71.00.

- > > There is, however a driver version 4.72 in the latest 2.4.4-ac
- > > kernels.
- > 
- > I've tried it but it was all the same - I came back to 4.71

It still seems like a BIOS issue.  Does is work on a default RH
installation, with the RH included kernel?

             I can't believe it's not UNIX!!!
------------------------------------------------------------
Leah Cunningham             |  SuSE Expert, NOS Engineer, 
Undisclosed Address         |  QA & Linux geek, et al.        

^ permalink raw reply	[flat|nested] 8+ messages in thread

end of thread, other threads:[~2001-05-17 14:28 UTC | newest]

Thread overview: 8+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2001-05-16 10:02 RH 7.1 on IBM xSeries 240 ps
2001-05-16 16:57 ` Leah Cunningham
2001-05-16 17:29   ` ps
2001-05-16 17:49     ` Leah Cunningham
2001-05-16 23:29 ` Alan Cox
     [not found] <fa.fhhq4kv.gguq9t@ifi.uio.no>
     [not found] ` <fa.fuo78ov.ikad9g@ifi.uio.no>
2001-05-17  9:48   ` Pim Zandbergen
2001-05-17 10:30     ` ps
2001-05-17 14:28       ` Leah Cunningham

This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.