From: Cliff Albert <cliff@oisec.net>
To: Yusuf Goolamabbas <yusufg@outblaze.com>
Cc: linux-kernel@vger.kernel.org, gibbs@scsiguy.com
Subject: Re: aic7xxx errors with 2.4.8-ac7 on 440gx mobo
Date: Mon, 20 Aug 2001 10:55:20 +0200 [thread overview]
Message-ID: <20010820105520.A22087@oisec.net> (raw)
In-Reply-To: <20010820083630.16182.qmail@yusufg.portal2.com>
In-Reply-To: <20010820083630.16182.qmail@yusufg.portal2.com>
On Mon, Aug 20, 2001 at 08:36:30AM -0000, Yusuf Goolamabbas wrote:
> Hi, 2.4.8 and 2.4.9 have no problems compiling and booting on a P3 500
> 440GX mobo (APIC not compiled in the kernel)
>
> With 2.4.8-ac7, I get SCSI errors and the kernel fails to boot. If I
> compile with APIC enabled and APIC on UP also enabled, it boots
> cleanly
I'm getting similair errors on 2.4.8-ac7 on my P2B-S motherboard using
the NEW AIC7xxx driver, the old isn't experiencing these problems. Further
i've been getting these errors since 2.4.3.
> booting with append="noapic", gives the same errors
This also didn't resolve my problems
> SCSI subsystem driver Revision: 1.00
> PCI: Assigned IRQ 11 for device 00:0c.0
> PCI: Sharing IRQ 11 with 00:0c.1
> PCI: Found IRQ 11 for device 00:0c.1
> PCI: Sharing IRQ 11 with 00:0c.0
>
> scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.1
> <Adaptec aic7896/97 Ultra2 SCSI adapter>
> aic7896/97: Ultra2 Wide Channel A, SCSI Id=7, 32/255 SCBs
>
> scsi1 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.1
> <Adaptec aic7896/97 Ultra2 SCSI adapter>
> aic7896/97: Ultra2 Wide Channel B, SCSI Id=7, 32/255 SCBs
SCSI subsystem driver Revision: 1.00
PCI: Found IRQ 14 for device 00:06.0
PCI: Sharing IRQ 14 with 00:04.2
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.1
<Adaptec aic7890/91 Ultra2 SCSI adapter>
aic7890/91: Ultra2 Wide Channel A, SCSI Id=7, 32/255 SCBs
>
> scsi0:0:0:0: Attempting to queue an ABORT message
> scsi0:0:0:0: Command already completed
> aic7xxx_abort returns 8194
> scsi0:0:0:0: Attempting to queue an ABORT message
> scsi0:0:0:0: Device is active, asserting ATN
> Recovery code sleeping
> Recovery code awake
> Timer Expired
> aic7xxx_abort returns 8195
> scsi0:0:0:0: Attempting to queue a TARGET RESET message
> aic7xxx_dev_reset returns 8195
> Recovery SCB completes
> scsi0:0:0:0: Attempting to queue an ABORT message
> ahc_intr: HOST_MSG_LOOP bad phase 0x0
> scsi0:0:0:0: Cmd aborted from QINFIFO
> aic7xxx_abort returns 8194
> scsi: device set offline - not ready or command retry failed after bus reset: host 0 channel 0 id 0 lun 0
> scsi0:0:1:0: Attempting to queue an ABORT message
> scsi0:0:1:0: Command already completed
> aic7xxx_abort returns 8194
> scsi0:0:1:0: Attempting to queue an ABORT message
> scsi0:0:1:0: Command already completed
> aic7xxx_abort returns 8194
> scsi0:0:1:0: Attempting to queue a TARGET RESET message
> scsi0:0:1:0: Is not an active device
> scsi0:0:1:0: Attempting to queue an ABORT message
> scsi0:0:1:0: Command already completed
> aic7xxx_abort returns 8194
scsi0:0:0:0: Attempting to queue an ABORT message
(scsi0:A:0:0): Queuing a recovery SCB
scsi0:0:0:0: Device is disconnected, re-queuing SCB
Recovery code sleeping
(scsi0:A:0:0): Abort Tag Message Sent
(scsi0:A:0:0): SCB 1 - Abort Tag Completed.
Recovery SCB completes
Recovery code awake
aic7xxx_abort returns 8194
scsi0:0:0:0: Attempting to queue an ABORT message
scsi0:0:0:0: Command found on device queue
aic7xxx_abort returns 8194
scsi0:0:0:0: Attempting to queue an ABORT message
(scsi0:A:0:0): Queuing a recovery SCB
scsi0:0:0:0: Device is disconnected, re-queuing SCB
Recovery code sleeping
(scsi0:A:0:0): Abort Tag Message Sent
(scsi0:A:0:0): SCB 4 - Abort Tag Completed.
Recovery SCB completes
Recovery code awake
aic7xxx_abort returns 8194
scsi0:0:0:0: Attempting to queue an ABORT message
(scsi0:A:0:0): Queuing a recovery SCB
scsi0:0:0:0: Device is disconnected, re-queuing SCB
Recovery code sleeping
(scsi0:A:0:0): Abort Tag Message Sent
(scsi0:A:0:0): SCB 2 - Abort Tag Completed.
Recovery SCB completes
Recovery code awake
aic7xxx_abort returns 8194
scsi0:0:0:0: Attempting to queue an ABORT message
(scsi0:A:0:0): Queuing a recovery SCB
scsi0:0:0:0: Device is disconnected, re-queuing SCB
Recovery code sleeping
(scsi0:A:0:0): Abort Tag Message Sent
(scsi0:A:0:0): SCB 9 - Abort Tag Completed.
Recovery SCB completes
Recovery code awake
aic7xxx_abort returns 8194
scsi0:0:0:0: Attempting to queue an ABORT message
(scsi0:A:0:0): Queuing a recovery SCB
scsi0:0:0:0: Device is disconnected, re-queuing SCB
(scsi0:A:0:0): Abort Tag Message Sent
Recovery code sleeping
(scsi0:A:0:0): SCB 0 - Abort Tag Completed.
Recovery SCB completes
Recovery code awake
aic7xxx_abort returns 8194
scsi0:0:0:0: Attempting to queue an ABORT message
scsi0:0:0:0: Command not found
aic7xxx_abort returns 8194
scsi0:0:0:0: Attempting to queue an ABORT message
scsi0:0:0:0: Command found on device queue
aic7xxx_abort returns 8194
scsi0:0:0:0: Attempting to queue an ABORT message
scsi0:0:0:0: Command not found
aic7xxx_abort returns 8194
scsi0:0:0:0: Attempting to queue an ABORT message
scsi0:0:0:0: Command found on device queue
aic7xxx_abort returns 8194
scsi0:0:0:0: Attempting to queue an ABORT message
scsi0:0:0:0: Command not found
aic7xxx_abort returns 8194
scsi0:0:0:0: Attempting to queue an ABORT message
scsi0:0:0:0: Command found on device queue
aic7xxx_abort returns 8194
scsi0:0:0:0: Attempting to queue an ABORT message
scsi0:0:0:0: Command not found
aic7xxx_abort returns 8194
scsi0:0:0:0: Attempting to queue an ABORT message
scsi0:0:0:0: Command found on device queue
aic7xxx_abort returns 8194
scsi0:0:0:0: Attempting to queue an ABORT message
(scsi0:A:0:0): Queuing a recovery SCB
scsi0:0:0:0: Device is disconnected, re-queuing SCB
(scsi0:A:0:0): Abort Tag Message Sent
Recovery code sleeping
(scsi0:A:0:0): SCB 11 - Abort Tag Completed.
Recovery SCB completes
Recovery code awake
aic7xxx_abort returns 8194
scsi0:0:0:0: Attempting to queue an ABORT message
(scsi0:A:0:0): Queuing a recovery SCB
scsi0:0:0:0: Device is disconnected, re-queuing SCB
Recovery code sleeping
(scsi0:A:0:0): Abort Tag Message Sent
(scsi0:A:0:0): SCB 6 - Abort Tag Completed.
Recovery SCB completes
Recovery code awake
aic7xxx_abort returns 8194
scsi0:0:0:0: Attempting to queue an ABORT message
(scsi0:A:0:0): Queuing a recovery SCB
scsi0:0:0:0: Device is disconnected, re-queuing SCB
Recovery code sleeping
(scsi0:A:0:0): Abort Tag Message Sent
(scsi0:A:0:0): SCB 3 - Abort Tag Completed.
Recovery SCB completes
Recovery code awake
aic7xxx_abort returns 8194
scsi0:0:0:0: Attempting to queue a TARGET RESET message
scsi0:0:0:0: Command not found
aic7xxx_dev_reset returns 8194
Device not ready. Make sure there is a disc in the drive.
Device not ready. Make sure there is a disc in the drive.
SCSI device listing is:
Vendor: QUANTUM Model: FIREBALL ST6.4S Rev: 0F0C
Type: Direct-Access ANSI SCSI revision: 02
(scsi0:A:0): 20.000MB/s transfers (20.000MHz, offset 15)
Vendor: IOMEGA Model: ZIP 100 Rev: J.03
Type: Direct-Access ANSI SCSI revision: 02
Vendor: YAMAHA Model: CRW2100S Rev: 1.0H
Type: CD-ROM ANSI SCSI revision: 02
(scsi0:A:5): 20.000MB/s transfers (20.000MHz, offset 7)
Vendor: PLEXTOR Model: CD-ROM PX-32TS Rev: 1.01
Type: CD-ROM ANSI SCSI revision: 02
(scsi0:A:6): 20.000MB/s transfers (20.000MHz, offset 15)
--
Cliff Albert | RIPE: CA3348-RIPE | www.oisec.net
cliff@oisec.net | 6BONE: CA2-6BONE | icq 18461740
next prev parent reply other threads:[~2001-08-20 8:55 UTC|newest]
Thread overview: 69+ messages / expand[flat|nested] mbox.gz Atom feed top
2001-08-20 8:36 aic7xxx errors with 2.4.8-ac7 on 440gx mobo Yusuf Goolamabbas
2001-08-20 8:55 ` Cliff Albert [this message]
2001-08-20 10:37 ` Alan Cox
2001-08-20 10:56 ` Yusuf Goolamabbas
2001-08-20 10:56 ` Alan Cox
2001-08-20 11:13 ` Yusuf Goolamabbas
2001-08-20 11:09 ` Alan Cox
2001-08-20 16:43 ` Doug Ledford
2001-08-20 12:46 ` Stefan Fleiter
2001-08-20 15:19 ` Ville Herva
2001-08-20 20:33 ` Justin T. Gibbs
2001-08-20 16:45 ` Doug Ledford
2001-08-20 17:23 ` Stefan Fleiter
2001-08-20 20:28 ` Justin T. Gibbs
2001-08-21 20:24 ` Stefan Fleiter
2001-08-20 16:21 ` Cliff Albert
2001-08-20 17:23 ` Peter T. Breuer
2001-08-20 17:28 ` Cliff Albert
2001-08-20 20:27 ` Justin T. Gibbs
2001-08-20 20:45 ` Cliff Albert
2001-08-20 21:04 ` Cliff Albert
2001-08-20 21:09 ` Cliff Albert
2001-08-20 21:45 ` Justin T. Gibbs
2001-08-20 22:36 ` aic7xxx with 2.4.9 on 7899P Sven Heinicke
2001-08-21 14:42 ` With Daniel Phillips Patch (was: aic7xxx with 2.4.9 on 7899P) Sven Heinicke
2001-08-21 15:08 ` Daniel Phillips
2001-08-21 16:48 ` Sven Heinicke
2001-08-21 17:18 ` Justin T. Gibbs
2001-08-21 22:49 ` Sven Heinicke
2001-08-22 13:06 ` Gérard Roudier
2001-08-21 17:26 ` Daniel Phillips
2001-08-21 17:55 ` Stephan von Krawczynski
2001-08-21 18:33 ` Justin T. Gibbs
2001-08-22 6:46 ` Jens Axboe
2001-08-22 13:24 ` Justin T. Gibbs
2001-08-22 15:05 ` With Daniel Phillips Patch David S. Miller
2001-08-22 18:21 ` Gérard Roudier
2001-08-22 18:32 ` David S. Miller
2001-08-22 18:32 ` Justin T. Gibbs
2001-08-22 18:46 ` David S. Miller
2001-08-22 19:41 ` Justin T. Gibbs
2001-08-22 20:19 ` David S. Miller
2001-08-22 21:07 ` Gérard Roudier
2001-08-22 21:14 ` David S. Miller
2001-08-22 21:14 ` David S. Miller
2001-08-22 21:40 ` Justin T. Gibbs
2001-08-22 23:09 ` David S. Miller
2001-08-23 0:01 ` Justin T. Gibbs
2001-08-23 0:40 ` David S. Miller
2001-08-23 0:55 ` Justin T. Gibbs
2001-08-23 1:03 ` Matthew Jacob
2001-08-23 1:08 ` David S. Miller
2001-08-23 1:32 ` Justin T. Gibbs
2001-08-23 1:39 ` David S. Miller
2001-08-23 1:49 ` Justin T. Gibbs
2001-08-21 22:44 ` With Daniel Phillips Patch (was: aic7xxx with 2.4.9 on 7899P) Sven Heinicke
2001-08-22 0:58 ` Daniel Phillips
2001-08-22 10:25 ` Marcelo Tosatti
2001-08-22 16:09 ` Sven Heinicke
2001-08-22 15:42 ` Marcelo Tosatti
2001-08-22 20:25 ` Sven Heinicke
2001-08-29 7:30 ` Andrey Nekrasov
2001-09-03 14:58 ` Marcelo Tosatti
2001-08-20 22:55 ` aic7xxx errors with 2.4.8-ac7 on 440gx mobo Cliff Albert
2001-08-21 0:36 ` Justin T. Gibbs
2001-08-21 15:34 ` Gérard Roudier
2001-08-20 21:44 ` Justin T. Gibbs
2001-08-20 21:48 ` Cliff Albert
2001-08-25 7:15 ` Cliff Albert
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20010820105520.A22087@oisec.net \
--to=cliff@oisec.net \
--cc=gibbs@scsiguy.com \
--cc=linux-kernel@vger.kernel.org \
--cc=yusufg@outblaze.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.