All of lore.kernel.org
 help / color / mirror / Atom feed
* 2.5.54 problem with IDE ICH4 and aic7xxx
@ 2003-01-05 16:54 Gregoire Favre
  2003-01-05 17:35 ` Justin T. Gibbs
  2003-01-09 22:56 ` 2.5.54 problem with IDE ICH4 and aic7xxx -> fixed in 2.5.55 Gregoire Favre
  0 siblings, 2 replies; 8+ messages in thread
From: Gregoire Favre @ 2003-01-05 16:54 UTC (permalink / raw)
  To: linux-kernel

Hello,

I have put whole dmesg, .config, lspci, ver_linux, /proc/interrupts,
/proc/ide/piix, /proc/partitions, /proc/scsi/aic7xxx/0,
/proc/scsi/aic7xxx/1, /proc/scsi/scsi under

http://ulima.unil.ch/greg/linux/2.5.54/

One could also find patch-2.5.45-mouse that I used such that my mouse
work (wireless one, reverse patch), and other patch I have applied are
the ones from linux-dvb :

cvs -d :pserver:anonymous@linuxtv.org:/cvs/linuxtv co dvb-kernel

But I get the same result without those patches ;-)

I got an MSI Max2-BLR which has an onboard IDE Raid that isn't acticated
in the BIOS (if I turn it on, it doesn't change anything at all...

Under 2.4.20 it boots perfectly...
What I found really strange is the time my IDE take to boot. More than
five minutes for thoses lines :

Linux video capture interface: v1.00
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH4: IDE controller at PCI slot 00:1f.1
ICH4: chipset revision 1
ICH4: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:pio
hda: IC35L120AVVA07-0, ATA DISK drive
hda: bad special flag: 0x03
hda: tagged command queueing enabled, command queue depth 8
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: SONY DVD RW DRU-500A, ATAPI CD/DVD-ROM drive
hdd: IOMEGA ZIP 250 ATAPI, ATAPI FLOPPY drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: host protected area => 1
hda: 241254720 sectors (123522 MB) w/1863KiB Cache, CHS=239340/16/63, UDMA(100)
 /dev/ide/host0/bus0/target0/lun0: p1 p2 p3 p4 < p5 p6 >
hdc: ATAPI 16X DVD-ROM DVD-R CD-R/RW drive, 8192kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.12
ide-floppy driver 0.99.newide
hdd: 244766kB, 489532 blocks, 512 sector size
hdd: 244736kB, 239/64/32 CHS, 4096 kBps, 512 sector size, 2941 rpm
hdd: The disk reports a capacity of 250640384 bytes, but the drive only handles 250
609664
hdd: The disk reports a capacity of 250640384 bytes, but the drive only handles 250
609664
 /dev/ide/host0/bus1/target1/lun0: unknown partition table
 /dev/ide/host0/bus1/target1/lun0: unknown partition table

Which is imediatly followed by:

aic7xxx: PCI Device 3:3:0 failed memory mapped test.  Using PIO.
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.25
        <Adaptec 29160B Ultra160 SCSI adapter>
        aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs

(scsi0:A:0): 80.000MB/s transfers (40.000MHz, offset 15, 16bit)
(scsi1:A:1:0): refuses WIDE negotiation.  Using 8bit transfers
(scsi0:A:15): 160.000MB/s transfers (80.000MHz DT, offset 63, 16bit)
  Vendor: IBM       Model: DDRS-39130D       Rev: DC1B
  Type:   Direct-Access                      ANSI SCSI revision: 02
scsi0:A:0:0: Tagged Queuing enabled.  Depth 253
  Vendor: SEAGATE   Model: ST336706LW        Rev: 0108
  Type:   Direct-Access                      ANSI SCSI revision: 03
scsi0:A:15:0: Tagged Queuing enabled.  Depth 253
scsi1 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.25
        <Adaptec 2940 Ultra SCSI adapter>
        aic7880: Ultra Single Channel A, SCSI Id=7, 16/253 SCBs

(scsi1:A:1): 10.000MB/s transfers (10.000MHz, offset 15)
(scsi1:A:2): 10.000MB/s transfers (10.000MHz, offset 8)
(scsi1:A:3): 10.000MB/s transfers (10.000MHz, offset 8)
  Vendor: TOSHIBA   Model: DVD-ROM SD-M1201  Rev: 1R04
  Type:   CD-ROM                             ANSI SCSI revision: 02
  Vendor: PLEXTOR   Model: CD-R   PX-R820T   Rev: 1.08
  Type:   CD-ROM                             ANSI SCSI revision: 02
  Vendor: PLEXTOR   Model: CD-R   PX-R820T   Rev: 1.08
  Type:   CD-ROM                             ANSI SCSI revision: 02
SCSI device sda: drive cache: write through
SCSI device sda: 17850000 512-byte hdwr sectors (9139 MB)
 /dev/scsi/host0/bus0/target0/lun0: p1 p2
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
SCSI device sdb: drive cache: write back
SCSI device sdb: 71687370 512-byte hdwr sectors (36704 MB)
 /dev/scsi/host0/bus0/target15/lun0: p1 p2
Attached scsi disk sdb at scsi0, channel 0, id 15, lun 0
sr0: scsi3-mmc drive: 32x/32x cd/rw xa/form2 cdda tray
Attached scsi CD-ROM sr0 at scsi1, channel 0, id 1, lun 0
sr1: scsi3-mmc drive: 20x/20x writer cd/rw xa/form2 cdda tray
Attached scsi CD-ROM sr1 at scsi1, channel 0, id 2, lun 0
sr2: scsi3-mmc drive: 20x/20x writer cd/rw xa/form2 cdda tray
Attached scsi CD-ROM sr2 at scsi1, channel 0, id 3, lun 0
device class 'input': registering

Should I do something different?

Thank you very much and have a great day ;-)

	Grégoire
________________________________________________________________
http://ulima.unil.ch/greg ICQ:16624071 mailto:greg@ulima.unil.ch

^ permalink raw reply	[flat|nested] 8+ messages in thread
end of thread, other threads:[~2003-01-09 22:48 UTC | newest]

Thread overview: 8+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2003-01-05 16:54 2.5.54 problem with IDE ICH4 and aic7xxx Gregoire Favre
2003-01-05 17:35 ` Justin T. Gibbs
2003-01-05 17:42   ` Gregoire Favre
2003-01-05 18:49     ` Alan Cox
2003-01-05 19:41       ` Gregoire Favre
2003-01-05 20:37         ` Alan Cox
2003-01-05 18:52   ` Gregoire Favre
2003-01-09 22:56 ` 2.5.54 problem with IDE ICH4 and aic7xxx -> fixed in 2.5.55 Gregoire Favre

This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.