* [parisc-linux] kernel compile @ 2003-02-03 2:02 Aaron St. Pierre 2003-02-03 4:11 ` Grant Grundler 0 siblings, 1 reply; 16+ messages in thread From: Aaron St. Pierre @ 2003-02-03 2:02 UTC (permalink / raw) To: parisc-linux I have been trying to get linux-2.4.20-pa23 to work with my j2240. For awhile now I thought it was the console, but it isn't it is the kernel. Here are the steps I took: Got the box running with debian kernel 2.4.17-32, updated to 2.4.18-32, and everything was working fine. I took the config from 2.4.18-32 and used that as my starting point for 2.4.20-pa23 ran make dep and make vmlinux; made and installed the modules The box just stops at the branching message. Let me note the console is set properly. I posted here before but think I was ignored becuase it was assumed I hadn't read the faq. Please I have read the faq, I just need help I would love to get this box working with a recent kernel and not have to depend on the packaged debian kernels. Thanks. -- Aaron St. Pierre tel: 978.828.6177 asp@ungod.com Increased knowledge will help you now. Have mate's phone bugged. ^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [parisc-linux] kernel compile 2003-02-03 2:02 [parisc-linux] kernel compile Aaron St. Pierre @ 2003-02-03 4:11 ` Grant Grundler 2003-02-03 5:33 ` Aaron St. Pierre 0 siblings, 1 reply; 16+ messages in thread From: Grant Grundler @ 2003-02-03 4:11 UTC (permalink / raw) To: Aaron St. Pierre; +Cc: parisc-linux On Sun, Feb 02, 2003 at 09:02:47PM -0500, Aaron St. Pierre wrote: > I took the config from 2.4.18-32 > and used that as my starting point for 2.4.20-pa23 Can you: # mv .config ../config-orig # yes "" | make oldconfig (or something like that) The default kernel should work on j2240. grant ps. FAQ has a link to "how to report kernel bugs" http://www.parisc-linux.org/faq/index.html#kernelbugreport ^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [parisc-linux] kernel compile 2003-02-03 4:11 ` Grant Grundler @ 2003-02-03 5:33 ` Aaron St. Pierre 2003-02-03 6:03 ` Grant Grundler 0 siblings, 1 reply; 16+ messages in thread From: Aaron St. Pierre @ 2003-02-03 5:33 UTC (permalink / raw) To: Grant Grundler; +Cc: parisc-linux First, thanks for the response, I really appreciate it. I setup a page with all of the information from the "basics" section of the faq. That page is : http://hadron.dyndns.org/parisc/ Grant, I did as you said, and the same thing happened. What disturbs me is when it stopped at the brancing message and I waited about 15 minutes then pressed the toc button there was still nothing in the pim ( I cleared it prior to boot) I hope this doesn't mean the kernel isn't even loading and it has something to do with palo. Maybe I am once again making this too complicated. If I left anything out let me know and I will add it. Thanks again for your help. :) In another life Grant Grundler wrote: > On Sun, Feb 02, 2003 at 09:02:47PM -0500, Aaron St. Pierre wrote: > > I took the config from 2.4.18-32 > > and used that as my starting point for 2.4.20-pa23 > > Can you: > # mv .config ../config-orig > # yes "" | make oldconfig > (or something like that) > > The default kernel should work on j2240. > > grant > > ps. FAQ has a link to "how to report kernel bugs" > http://www.parisc-linux.org/faq/index.html#kernelbugreport -- Aaron St. Pierre tel: 978.828.6177 asp@ungod.com A day without sunshine is like a day without orange juice. ^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [parisc-linux] kernel compile 2003-02-03 5:33 ` Aaron St. Pierre @ 2003-02-03 6:03 ` Grant Grundler 2003-02-03 6:07 ` Grant Grundler 2003-02-03 6:43 ` Aaron St. Pierre 0 siblings, 2 replies; 16+ messages in thread From: Grant Grundler @ 2003-02-03 6:03 UTC (permalink / raw) To: Aaron St. Pierre; +Cc: parisc-linux On Mon, Feb 03, 2003 at 12:33:36AM -0500, Aaron St. Pierre wrote: > I setup a page with all of the information from the "basics" section > of the faq. That page is : http://hadron.dyndns.org/parisc/ very good. j2240 is pa8200 - ie 64-bit capable. But don't use 64-bit kernel unless you know why you need to. > Grant, I did as you said, and the same thing happened. What disturbs me > is when it stopped at the brancing message and I waited about 15 minutes > then pressed the toc button there was still nothing in the pim ( I > cleared it prior to boot) I hope this doesn't mean the kernel isn't even > loading and it has something to do with palo. your PIM dump only has the HPMC/memory/IO sections. Didn't "ser pim" give you LPMC and TOC sections too? Secondly, since your j2240 is dual CPU, the PIM dump should contain the same info (HPMC, LPMC, TOC) for both CPUs. Can you check if you firmware is anywhere near the current? (See http://www.parisc-linux.org/faq/index.html#PDCupdate) And the following from your log worries me despite the "ignore" part: | Information: Boot device can't seek past 2Gb (ignore next error). | byteio_read: seekread() returned -1 expected 2048 But nothing else indicated a problem loading the vmlinux. I just don't see that when booting my a500. It could be a difference in how palo interacts with IODC. If you don't get any other hot tips, start disabling things in the .config that you don't need: Parport, SBA/LBA/IOSAPIC, USB, LCD/LED support, wireless, extra lan/scsi drivers, etc. grant ^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [parisc-linux] kernel compile 2003-02-03 6:03 ` Grant Grundler @ 2003-02-03 6:07 ` Grant Grundler 2003-02-03 6:43 ` Aaron St. Pierre 1 sibling, 0 replies; 16+ messages in thread From: Grant Grundler @ 2003-02-03 6:07 UTC (permalink / raw) To: Aaron St. Pierre; +Cc: parisc-linux On Sun, Feb 02, 2003 at 11:03:59PM -0700, Grant Grundler wrote: > If you don't get any other hot tips, start disabling things in > the .config that you don't need: Parport, SBA/LBA/IOSAPIC, > USB, LCD/LED support, wireless, extra lan/scsi drivers, etc. I forgot to mention STI drivers - ditch those if you are using serial console even though I doubt they are the problem. grant ^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [parisc-linux] kernel compile 2003-02-03 6:03 ` Grant Grundler 2003-02-03 6:07 ` Grant Grundler @ 2003-02-03 6:43 ` Aaron St. Pierre 2003-02-03 10:19 ` Michael Wood 2003-02-03 16:53 ` Grant Grundler 1 sibling, 2 replies; 16+ messages in thread From: Aaron St. Pierre @ 2003-02-03 6:43 UTC (permalink / raw) To: Grant Grundler; +Cc: parisc-linux Yea I missed that one. With this version of the firmware you have to request the specific PIM, HPMC, LPMC, TOC. Anyway I got the the TOC information for both processors after I tried to boot my kernel. It is all on that page ( http://hadron.dyndns.org/parisc/ ) I also added a link to the firmware. I am running 2.0 of the firmware and according to hp the most recent is 2.1 or : Patch Name: /firmware_patches/hp/cpu/PF_CJ224021 Description: HP 9000 Model J2240 firmware 2.1 patch Date : 00/10/06 I will start popping stuff out of the kernel, although I am sure I took out all of the stuff wrt graphics. Another try for persistance sake wont hurt :) As far as the palo message, i only started noticing it when I went to v1.2 of palo. One thing I should note, when I set up / i made it ext3, boot is off of / and not its own fs so when i realized what i did I just changed fstab accordingly so it would mount as ext2, although that couldn't be the problem either since it is loading the debian kernels. Perhaps sleep is in order ? :) In another life Grant Grundler wrote: > On Mon, Feb 03, 2003 at 12:33:36AM -0500, Aaron St. Pierre wrote: > > I setup a page with all of the information from the "basics" section > > of the faq. That page is : http://hadron.dyndns.org/parisc/ > > very good. > > j2240 is pa8200 - ie 64-bit capable. > But don't use 64-bit kernel unless you know why you need to. > > > Grant, I did as you said, and the same thing happened. What disturbs me > > is when it stopped at the brancing message and I waited about 15 minutes > > then pressed the toc button there was still nothing in the pim ( I > > cleared it prior to boot) I hope this doesn't mean the kernel isn't even > > loading and it has something to do with palo. > > your PIM dump only has the HPMC/memory/IO sections. > Didn't "ser pim" give you LPMC and TOC sections too? > > Secondly, since your j2240 is dual CPU, the PIM dump should contain > the same info (HPMC, LPMC, TOC) for both CPUs. > > Can you check if you firmware is anywhere near the current? > (See http://www.parisc-linux.org/faq/index.html#PDCupdate) > > > And the following from your log worries me despite the "ignore" part: > | Information: Boot device can't seek past 2Gb (ignore next error). > | byteio_read: seekread() returned -1 expected 2048 > > But nothing else indicated a problem loading the vmlinux. > I just don't see that when booting my a500. > It could be a difference in how palo interacts with IODC. > > If you don't get any other hot tips, start disabling things in > the .config that you don't need: Parport, SBA/LBA/IOSAPIC, > USB, LCD/LED support, wireless, extra lan/scsi drivers, etc. > > grant > _______________________________________________ > parisc-linux mailing list > parisc-linux@lists.parisc-linux.org > http://lists.parisc-linux.org/mailman/listinfo/parisc-linux -- Aaron St. Pierre tel: 978.828.6177 asp@ungod.com Men say of women what pleases them; women do with men what pleases them. -- DeSegur ^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [parisc-linux] kernel compile 2003-02-03 6:43 ` Aaron St. Pierre @ 2003-02-03 10:19 ` Michael Wood 2003-02-03 15:37 ` Aaron St. Pierre 2003-02-03 16:53 ` Grant Grundler 1 sibling, 1 reply; 16+ messages in thread From: Michael Wood @ 2003-02-03 10:19 UTC (permalink / raw) To: Aaron St. Pierre; +Cc: Grant Grundler, parisc-linux On Mon, Feb 03, 2003 at 01:43:28AM -0500, Aaron St. Pierre wrote: [snip] > As far as the palo message, i only started noticing it when I went to > v1.2 of palo. One thing I should note, when I set up / i made it ext3, > boot is off of / and not its own fs so when i realized what i did I [snip] Your boot partition (/) is < 2GB, right? -- Michael Wood <mwood@its.uct.ac.za> ^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [parisc-linux] kernel compile 2003-02-03 10:19 ` Michael Wood @ 2003-02-03 15:37 ` Aaron St. Pierre 2003-02-04 16:57 ` Paul Bame 0 siblings, 1 reply; 16+ messages in thread From: Aaron St. Pierre @ 2003-02-03 15:37 UTC (permalink / raw) To: Michael Wood, Grant Grundler, parisc-linux Yes, the boot partition is < 2GB. In fact here is the partion table as reported from fdisk. Disk /dev/sda: 9100 MB, 9100044288 bytes 64 heads, 32 sectors/track, 8678 cylinders Units = cylinders of 2048 * 512 = 1048576 bytes Device Boot Start End Blocks Id System /dev/sda1 * 1 29 29680 f0 Linux/PA-RISC boot /dev/sda2 30 267 243712 83 Linux /dev/sda3 268 1221 976896 82 Linux swap /dev/sda4 1222 5989 4882432 5 Extended /dev/sda5 1222 3128 1952752 83 Linux /dev/sda6 3129 5989 2929648 83 Linux I will also add this info to my parisc page. I am going to start ripping things out of the kernel a bit later today. One thing I will admit ignorance about is the F0 partition. The debian install got vmlinux32 to live in there but I haven't gotten any other kernels to live in there. Not that that really matters since once can boot off of a kernel that lives in an ext2 fs as long as it is within the first 2GB. Yawn, just waking up ... In another life Michael Wood wrote: > On Mon, Feb 03, 2003 at 01:43:28AM -0500, Aaron St. Pierre wrote: > [snip] > > As far as the palo message, i only started noticing it when I went to > > v1.2 of palo. One thing I should note, when I set up / i made it ext3, > > boot is off of / and not its own fs so when i realized what i did I > [snip] > > Your boot partition (/) is < 2GB, right? > > -- > Michael Wood <mwood@its.uct.ac.za> -- Aaron St. Pierre tel: 978.828.6177 asp@ungod.com Have at you! ^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [parisc-linux] kernel compile 2003-02-03 15:37 ` Aaron St. Pierre @ 2003-02-04 16:57 ` Paul Bame 2003-02-04 18:03 ` Grant Grundler 2003-02-04 19:17 ` Aaron St. Pierre 0 siblings, 2 replies; 16+ messages in thread From: Paul Bame @ 2003-02-04 16:57 UTC (permalink / raw) To: Aaron St. Pierre; +Cc: Michael Wood, Grant Grundler, parisc-linux On Mon, Feb 03, 2003 at 10:37:35AM -0500, Aaron St. Pierre wrote: > Yes, the boot partition is < 2GB. In fact here is the partion table as > reported from fdisk. > > Disk /dev/sda: 9100 MB, 9100044288 bytes > 64 heads, 32 sectors/track, 8678 cylinders > Units = cylinders of 2048 * 512 = 1048576 bytes > > Device Boot Start End Blocks Id System > /dev/sda1 * 1 29 29680 f0 Linux/PA-RISC boot > /dev/sda2 30 267 243712 83 Linux Your TOC dump indicated a likely death in firmware, which is consistent with trying to load a kernel from beyond the 2G mark. Indeed your /dev/sda2 ends past the 2G mark, so you can expect that sometimes it'll work and sometimes it won't. -P ^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [parisc-linux] kernel compile 2003-02-04 16:57 ` Paul Bame @ 2003-02-04 18:03 ` Grant Grundler 2003-02-04 19:17 ` Aaron St. Pierre 1 sibling, 0 replies; 16+ messages in thread From: Grant Grundler @ 2003-02-04 18:03 UTC (permalink / raw) To: Paul Bame; +Cc: Aaron St. Pierre, Michael Wood, parisc-linux On Tue, Feb 04, 2003 at 09:57:54AM -0700, Paul Bame wrote: > On Mon, Feb 03, 2003 at 10:37:35AM -0500, Aaron St. Pierre wrote: > > Yes, the boot partition is < 2GB. In fact here is the partion table as > > reported from fdisk. > > > > Disk /dev/sda: 9100 MB, 9100044288 bytes > > 64 heads, 32 sectors/track, 8678 cylinders > > Units = cylinders of 2048 * 512 = 1048576 bytes > > > > Device Boot Start End Blocks Id System > > /dev/sda1 * 1 29 29680 f0 Linux/PA-RISC boot > > /dev/sda2 30 267 243712 83 Linux > > Your TOC dump indicated a likely death in firmware, which is consistent > with trying to load a kernel from beyond the 2G mark. Indeed your > /dev/sda2 ends past the 2G mark, so you can expect that sometimes > it'll work and sometimes it won't. Paul, Are you sure? 267*1048576 == 279969792 == 279,969,792 That's 280MB if I've placed the comas right. grant ^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [parisc-linux] kernel compile 2003-02-04 16:57 ` Paul Bame 2003-02-04 18:03 ` Grant Grundler @ 2003-02-04 19:17 ` Aaron St. Pierre 1 sibling, 0 replies; 16+ messages in thread From: Aaron St. Pierre @ 2003-02-04 19:17 UTC (permalink / raw) To: Paul Bame; +Cc: Michael Wood, Grant Grundler, parisc-linux Paul, My root filesystem is 250MB. parisc:~# df -kh Filesystem Size Used Avail Use% Mounted on /dev/sda2 231M 52M 168M 24% / /dev/sda5 1.9G 212M 1.6G 12% /var /dev/sda6 2.8G 1009M 1.7G 38% /usr Don't know if you saw the thread, but for some reason 2.5.58 boots, there are problems after, which is expected with a development kernel, but it boots nonetheless and that is hopeful :) Is there perhaps some other way I should be organizing my swap and filesystems ? I followed the instructions from http://www.parisc-linux.org/software/install.html. Thanks In another life Paul Bame wrote: > On Mon, Feb 03, 2003 at 10:37:35AM -0500, Aaron St. Pierre wrote: > > Yes, the boot partition is < 2GB. In fact here is the partion table as > > reported from fdisk. > > > > Disk /dev/sda: 9100 MB, 9100044288 bytes > > 64 heads, 32 sectors/track, 8678 cylinders > > Units = cylinders of 2048 * 512 = 1048576 bytes > > > > Device Boot Start End Blocks Id System > > /dev/sda1 * 1 29 29680 f0 Linux/PA-RISC boot > > /dev/sda2 30 267 243712 83 Linux > > Your TOC dump indicated a likely death in firmware, which is consistent > with trying to load a kernel from beyond the 2G mark. Indeed your > /dev/sda2 ends past the 2G mark, so you can expect that sometimes > it'll work and sometimes it won't. > > -P > _______________________________________________ > parisc-linux mailing list > parisc-linux@lists.parisc-linux.org > http://lists.parisc-linux.org/mailman/listinfo/parisc-linux -- Aaron St. Pierre tel: 978.828.6177 asp@ungod.com <rcw> liiwi: printk("CPU0 on fire\n"); ^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [parisc-linux] kernel compile 2003-02-03 6:43 ` Aaron St. Pierre 2003-02-03 10:19 ` Michael Wood @ 2003-02-03 16:53 ` Grant Grundler 2003-02-03 17:38 ` Joel Soete 1 sibling, 1 reply; 16+ messages in thread From: Grant Grundler @ 2003-02-03 16:53 UTC (permalink / raw) To: Aaron St. Pierre; +Cc: parisc-linux On Mon, Feb 03, 2003 at 01:43:28AM -0500, Aaron St. Pierre wrote: > Anyway I got the the TOC information for both processors after > I tried to boot my kernel. It is > all on that page ( http://hadron.dyndns.org/parisc/ ) IIA Offset = 0x00000000f0080570 that's not a kernel address. Looks like a PDC call died. :^( > I also added a link to the firmware. I am running 2.0 of the firmware > and according to hp the most recent is 2.1 or : > > Patch Name: /firmware_patches/hp/cpu/PF_CJ224021 > Description: HP 9000 Model J2240 firmware 2.1 patch > Date : 00/10/06 hmm...I'd stick with 2.0 for now. > I will start popping stuff out of the kernel, although I am sure I took > out all of the stuff wrt graphics. Another try for persistance sake wont > hurt :) You still have STI drivers enabled and CONFIG_FB enabled. I'd start with those and then remove others one-by-one. > As far as the palo message, i only started noticing it when I went to > v1.2 of palo. One thing I should note, when I set up / i made it ext3, > boot is off of / and not its own fs so when i realized what i did I just > changed fstab accordingly so it would mount as ext2, although that > couldn't be the problem either since it is loading the debian kernels. / can be ext3. Palo doesn't care since ext2/ext3 are compatible. What's important is /boot/vmlinux is < 2GB on disk. grant ^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [parisc-linux] kernel compile 2003-02-03 16:53 ` Grant Grundler @ 2003-02-03 17:38 ` Joel Soete 2003-02-03 18:59 ` Aaron St. Pierre 0 siblings, 1 reply; 16+ messages in thread From: Joel Soete @ 2003-02-03 17:38 UTC (permalink / raw) To: grundler, Aaron St. Pierre; +Cc: parisc-linux Aaron, Just A comment on your web page 'Comments': warning concerning 'mathemu' code are well known annoying but armless. I try to remove them but this broken to much original hp code :( Now, the stupid question: do you try to boot from a serial console? I also would like to know if you really have an ide cdrom on your J? If yes, could you try to unplug it (pw supply and data flat cable) to reboot with your new kernel? hth, Joel >-- Original Message -- >To: "Aaron St. Pierre" <asp@ungod.com> >Cc: parisc-linux@lists.parisc-linux.org >Subject: Re: [parisc-linux] kernel compile >From: grundler@dsl2.external.hp.com (Grant Grundler) >Date: Mon, 3 Feb 2003 09:53:21 -0700 > > >On Mon, Feb 03, 2003 at 01:43:28AM -0500, Aaron St. Pierre wrote: >> Anyway I got the the TOC information for both processors after >> I tried to boot my kernel. It is >> all on that page ( http://hadron.dyndns.org/parisc/ ) > >IIA Offset = 0x00000000f0080570 > >that's not a kernel address. Looks like a PDC call died. :^( > >> I also added a link to the firmware. I am running 2.0 of the firmware >> and according to hp the most recent is 2.1 or : >> >> Patch Name: /firmware_patches/hp/cpu/PF_CJ224021 >> Description: HP 9000 Model J2240 firmware 2.1 patch >> Date : 00/10/06 > >hmm...I'd stick with 2.0 for now. > >> I will start popping stuff out of the kernel, although I am sure I took >> out all of the stuff wrt graphics. Another try for persistance sake wont >> hurt :) > >You still have STI drivers enabled and CONFIG_FB enabled. >I'd start with those and then remove others one-by-one. > >> As far as the palo message, i only started noticing it when I went to >> v1.2 of palo. One thing I should note, when I set up / i made it ext3, >> boot is off of / and not its own fs so when i realized what i did I just >> changed fstab accordingly so it would mount as ext2, although that >> couldn't be the problem either since it is loading the debian kernels. > >/ can be ext3. Palo doesn't care since ext2/ext3 are compatible. >What's important is /boot/vmlinux is < 2GB on disk. > >grant >_______________________________________________ >parisc-linux mailing list >parisc-linux@lists.parisc-linux.org >http://lists.parisc-linux.org/mailman/listinfo/parisc-linux --------------------------------- Vous surfez avec une ligne classique ? Faites des economies avec Tiscali Complete ... Plus d'info sur http://complete.tiscali.be ^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [parisc-linux] kernel compile 2003-02-03 17:38 ` Joel Soete @ 2003-02-03 18:59 ` Aaron St. Pierre 2003-02-04 2:49 ` Aaron St. Pierre 0 siblings, 1 reply; 16+ messages in thread From: Aaron St. Pierre @ 2003-02-03 18:59 UTC (permalink / raw) To: Joel Soete; +Cc: grundler, parisc-linux Joel, I figured so, but thought I should note it since well I am running out of answers ;) Here is the setup right now: I have a laptop running minicom connected to the J2240 through the serial port. I can see the init codes and tests happening through the serial console, so to answer your question :) yes I do boot from a serial console... As far as the cdrom, it is not ide, it is scsi, and it seems to work fine /dev/cdrom --> sr0. I inserted a cdrom (just to test) and mounted iso9660 without problems. I am going to remove ide stuff from the kernel after I test with what grant suggested. Just for the sake of documentation I will add compile logs as script files for the next builds. They will be on that page as I complete them. Fun day of pancake making ahead :) In another life Joel Soete wrote: > Aaron, > > Just A comment on your web page 'Comments': > warning concerning 'mathemu' code are well known annoying but armless. > > I try to remove them but this broken to much original hp code :( > > Now, the stupid question: do you try to boot from a serial console? > > I also would like to know if you really have an ide cdrom on your J? > > If yes, could you try to unplug it (pw supply and data flat cable) to reboot > with your new kernel? > > hth, > Joel > > > > >-- Original Message -- > >To: "Aaron St. Pierre" <asp@ungod.com> > >Cc: parisc-linux@lists.parisc-linux.org > >Subject: Re: [parisc-linux] kernel compile > >From: grundler@dsl2.external.hp.com (Grant Grundler) > >Date: Mon, 3 Feb 2003 09:53:21 -0700 > > > > > >On Mon, Feb 03, 2003 at 01:43:28AM -0500, Aaron St. Pierre wrote: > >> Anyway I got the the TOC information for both processors after > >> I tried to boot my kernel. It is > >> all on that page ( http://hadron.dyndns.org/parisc/ ) > > > >IIA Offset = 0x00000000f0080570 > > > >that's not a kernel address. Looks like a PDC call died. :^( > > > >> I also added a link to the firmware. I am running 2.0 of the firmware > >> and according to hp the most recent is 2.1 or : > >> > >> Patch Name: /firmware_patches/hp/cpu/PF_CJ224021 > >> Description: HP 9000 Model J2240 firmware 2.1 patch > >> Date : 00/10/06 > > > >hmm...I'd stick with 2.0 for now. > > > >> I will start popping stuff out of the kernel, although I am sure I took > >> out all of the stuff wrt graphics. Another try for persistance sake wont > >> hurt :) > > > >You still have STI drivers enabled and CONFIG_FB enabled. > >I'd start with those and then remove others one-by-one. > > > >> As far as the palo message, i only started noticing it when I went to > >> v1.2 of palo. One thing I should note, when I set up / i made it ext3, > >> boot is off of / and not its own fs so when i realized what i did I just > >> changed fstab accordingly so it would mount as ext2, although that > >> couldn't be the problem either since it is loading the debian kernels. > > > >/ can be ext3. Palo doesn't care since ext2/ext3 are compatible. > >What's important is /boot/vmlinux is < 2GB on disk. > > > >grant > >_______________________________________________ > >parisc-linux mailing list > >parisc-linux@lists.parisc-linux.org > >http://lists.parisc-linux.org/mailman/listinfo/parisc-linux > > > --------------------------------- > Vous surfez avec une ligne classique ? > Faites des economies avec Tiscali Complete > ... Plus d'info sur http://complete.tiscali.be > -- Aaron St. Pierre tel: 978.828.6177 asp@ungod.com 667: The neighbor of the beast. ^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [parisc-linux] kernel compile 2003-02-03 18:59 ` Aaron St. Pierre @ 2003-02-04 2:49 ` Aaron St. Pierre 2003-02-04 5:26 ` Grant Grundler 0 siblings, 1 reply; 16+ messages in thread From: Aaron St. Pierre @ 2003-02-04 2:49 UTC (permalink / raw) To: Joel Soete; +Cc: grundler, parisc-linux Okay.... I cannot explain this AT ALL, but look at this : Linux parisc 2.5.58-pa2 #1 Mon Feb 3 19:05:50 EST 2003 parisc unknown unknown GNU/Linux Yes 2.5 compiled and booted. It was a crap shoot. Now I have to figure out how to get modules to work. I had to take them out since I was getting a compile time error. This is just wierd. Well I suppose I shouldn't complain, this was the FIRST kernel that I built that actually booted. After about thirty or fourty compiles I have to say my persistence has paid off ;) I am gonna muck with the module stuff, If it is important to anyone I will maintain the page at http://hadron.dyndns.org/parisc/ Thanks again for all of your help ! -- Aaron St. Pierre tel: 978.828.6177 asp@ungod.com "I'm in Pittsburgh. Why am I here?" -- Harold Urey, Nobel Laureate ^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [parisc-linux] kernel compile 2003-02-04 2:49 ` Aaron St. Pierre @ 2003-02-04 5:26 ` Grant Grundler 0 siblings, 0 replies; 16+ messages in thread From: Grant Grundler @ 2003-02-04 5:26 UTC (permalink / raw) To: Aaron St. Pierre; +Cc: Joel Soete, parisc-linux On Mon, Feb 03, 2003 at 09:49:04PM -0500, Aaron St. Pierre wrote: > Yes 2.5 compiled and booted. It was a crap shoot. Now I have to > figure out how to get modules to work. Modules are broken in 2.5.x and still not fixed with 2.5.59. Someone volunteered already to fix it but it hasn't happened yet. Not sure if access to HW or lack of time is the problem. > Well I suppose I shouldn't complain, this was the FIRST kernel that > I built that actually booted. After about thirty or fourty compiles I > have to say my persistence has paid off ;) wierd. I guess it has. grant ^ permalink raw reply [flat|nested] 16+ messages in thread
end of thread, other threads:[~2003-02-04 19:18 UTC | newest] Thread overview: 16+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2003-02-03 2:02 [parisc-linux] kernel compile Aaron St. Pierre 2003-02-03 4:11 ` Grant Grundler 2003-02-03 5:33 ` Aaron St. Pierre 2003-02-03 6:03 ` Grant Grundler 2003-02-03 6:07 ` Grant Grundler 2003-02-03 6:43 ` Aaron St. Pierre 2003-02-03 10:19 ` Michael Wood 2003-02-03 15:37 ` Aaron St. Pierre 2003-02-04 16:57 ` Paul Bame 2003-02-04 18:03 ` Grant Grundler 2003-02-04 19:17 ` Aaron St. Pierre 2003-02-03 16:53 ` Grant Grundler 2003-02-03 17:38 ` Joel Soete 2003-02-03 18:59 ` Aaron St. Pierre 2003-02-04 2:49 ` Aaron St. Pierre 2003-02-04 5:26 ` Grant Grundler
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.