* RE: IDE Timeout problem on Intel PIIX3 (Triton 2) chipset
@ 2004-06-28 20:27 Chris Rankin
2004-06-29 1:21 ` Patrick Dreker
0 siblings, 1 reply; 7+ messages in thread
From: Chris Rankin @ 2004-06-28 20:27 UTC (permalink / raw)
To: linux-ide; +Cc: meelis.roos, patrick
> Any kernel above and including 2.4.21 (including
> 2.6.5 and 2.6.7, others not tested) produces the
> following errors quite often (once or twice per
> minute, with the corresponding delay) and the
> harddisk drops out of DMA.
Linux 2.4.26-UP is fine for me here, for both hda and
hdb. This box has 64 MB RAM, amd the kernel is
compiled with gcc-3.2.3.
# lspci
00:00.0 Host bridge: Intel Corp. 430VX - 82437VX TVX
[Triton VX] (rev 02)
00:07.0 ISA bridge: Intel Corp. 82371SB PIIX3 ISA
[Natoma/Triton II] (rev 01)
00:07.1 IDE interface: Intel Corp. 82371SB PIIX3 IDE
[Natoma/Triton II]
00:07.2 USB Controller: Intel Corp. 82371SB PIIX3 USB
[Natoma/Triton II] (rev 01)
00:08.0 VGA compatible controller: ATI Technologies
Inc 3D Rage I/II 215GT [Mach64 GT] (rev 41)
00:0d.0 VGA compatible controller: Matrox Graphics,
Inc. MGA 2164W [Millennium II]
00:0e.0 PCI bridge: Digital Equipment Corporation
DECchip 21152 (rev 03)
00:0f.0 Ethernet controller: Intel Corp. 82557/8/9
[Ethernet Pro 100] (rev 08)
01:04.0 Ethernet controller: Intel Corp. 82557/8/9
[Ethernet Pro 100] (rev 05)
01:05.0 Ethernet controller: Intel Corp. 82557/8/9
[Ethernet Pro 100] (rev 05)
# cat /proc/ide/hda/settings
name value min
max mode
---- ----- ---
--- ----
acoustic 0 0
254 rw
address 0 0
2 rw
bios_cyl 787 0
65535 rw
bios_head 128 0
255 rw
bios_sect 63 0
63 rw
breada_readahead 8 0
255 rw
bswap 0 0
1 r
current_speed 34 0
70 rw
failures 0 0
65535 rw
file_readahead 124 0
16384 rw
init_speed 34 0
70 rw
io_32bit 3 0
3 rw
keepsettings 0 0
1 rw
lun 0 0
7 rw
max_failures 1 0
65535 rw
max_kb_per_request 128 1
255 rw
multcount 16 0
16 rw
nice1 1 0
1 rw
nowerr 0 0
1 rw
number 0 0
3 rw
pio_mode write-only 0
255 w
slow 0 0
1 rw
unmaskirq 1 0
1 rw
using_dma 1 0
1 rw
wcache 0 0
1 rw
# cat /proc/ide/hdb/settings
name value min
max mode
---- ----- ---
--- ----
acoustic 0 0
254 rw
address 0 0
2 rw
bios_cyl 667 0
65535 rw
bios_head 240 0
255 rw
bios_sect 63 0
63 rw
breada_readahead 8 0
255 rw
bswap 0 0
1 r
current_speed 0 0
70 rw
failures 0 0
65535 rw
file_readahead 124 0
16384 rw
init_speed 0 0
70 rw
io_32bit 3 0
3 rw
keepsettings 0 0
1 rw
lun 0 0
7 rw
max_failures 1 0
65535 rw
max_kb_per_request 128 1
255 rw
multcount 16 0
16 rw
nice1 1 0
1 rw
nowerr 0 0
1 rw
number 1 0
3 rw
pio_mode write-only 0
255 w
slow 0 0
1 rw
unmaskirq 1 0
1 rw
using_dma 1 0
1 rw
wcache 0 0
1 rw
# uptime
21:21:38 up 75 days, 1 min, 5 users, load average:
0.00, 0.00, 0.00
Uniform Multi-Platform E-IDE driver Revision:
7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes;
override with idebus=xx
PIIX3: IDE controller at PCI slot 00:07.1
PIIX3: chipset revision 0
PIIX3: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xefa0-0xefa7, BIOS settings:
hda:pio, hdb:pio
ide1: BM-DMA at 0xefa8-0xefaf, BIOS settings:
hdc:pio, hdd:pio
hda: WDC AC33200L, ATA DISK drive
hdb: WDC AC35100L, ATA DISK drive
blk: queue c02b5080, I/O limit 4095Mb (mask
0xffffffff)
blk: queue c02b51bc, I/O limit 4095Mb (mask
0xffffffff)
hdc: TOSHIBA CD-ROM XM-6002B, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: task_no_data_intr: status=0x51 { DriveReady
SeekComplete Error }
hda: task_no_data_intr: error=0x04 { DriveStatusError
}
hda: 6346368 sectors (3249 MB) w/256KiB Cache,
CHS=787/128/63, DMA
hdb: attached ide-disk driver.
hdb: task_no_data_intr: status=0x51 { DriveReady
SeekComplete Error }
hdb: task_no_data_intr: error=0x04 { DriveStatusError
}
hdb: host protected area => 1
hdb: 10085040 sectors (5164 MB) w/256KiB Cache,
CHS=667/240/63, (U)DMA
Partition check:
hda: hda1 hda2 hda3
hdb: hdb1 hdb2 hdb3 hdb4
# cat /proc/interrupts
CPU0
0: 648044291 XT-PIC timer
1: 6916 XT-PIC keyboard
2: 0 XT-PIC cascade
4: 27998 XT-PIC serial
9: 385 XT-PIC usb-uhci
10: 13465208 XT-PIC eth2, eth0
11: 604729 XT-PIC eth1
14: 4091193 XT-PIC ide0
15: 36 XT-PIC ide1
NMI: 0
LOC: 0
ERR: 0
MIS: 0
Cheers,
Chris
___________________________________________________________ALL-NEW Yahoo! Messenger - sooooo many all-new ways to express yourself http://uk.messenger.yahoo.com
^ permalink raw reply [flat|nested] 7+ messages in thread* Re: IDE Timeout problem on Intel PIIX3 (Triton 2) chipset
2004-06-28 20:27 IDE Timeout problem on Intel PIIX3 (Triton 2) chipset Chris Rankin
@ 2004-06-29 1:21 ` Patrick Dreker
0 siblings, 0 replies; 7+ messages in thread
From: Patrick Dreker @ 2004-06-29 1:21 UTC (permalink / raw)
To: Chris Rankin; +Cc: linux-ide, meelis.roos
Am Montag, 28. Juni 2004 22:27 schrieb Chris Rankin:
> > Any kernel above and including 2.4.21 (including
> > 2.6.5 and 2.6.7, others not tested) produces the
> > following errors quite often (once or twice per
> > minute, with the corresponding delay) and the
> > harddisk drops out of DMA.
>
> Linux 2.4.26-UP is fine for me here, for both hda and
> hdb. This box has 64 MB RAM, amd the kernel is
> compiled with gcc-3.2.3.
Actually I tested 2.4.19, 20, 21, 22, 24, 26 and 2.6.5 and 7 and all from
2.4.21 on fail. All kernels compiled for SMP, but the system only has one CPU
(second CPU is waiting for the IDE problem to tracked down...)
I have triggered a compile of all pre and rc version between 2.4.20 and 2.4.21
and will do narrow it down tomorrow. (I know I'll probably need only 3 or 4
of those kernels, but having them all available will make testing easier...
Patrick
--
Patrick Dreker
GPG KeyID : 0xFCC2F7A7 (Patrick Dreker)
Fingerprint: 7A21 FC7F 707A C498 F370 1008 7044 66DA FCC2 F7A7
Key available from keyservers
^ permalink raw reply [flat|nested] 7+ messages in thread
[parent not found: <E1Bevgk-0007jR-4F@rhn.tartu-labor>]
* Re: IDE Timeout problem on Intel PIIX3 (Triton 2) chipset
[not found] <E1Bevgk-0007jR-4F@rhn.tartu-labor>
@ 2004-06-28 18:47 ` Meelis Roos
0 siblings, 0 replies; 7+ messages in thread
From: Meelis Roos @ 2004-06-28 18:47 UTC (permalink / raw)
To: Patrick Dreker, Linux Kernel list
> Any kernel above and including 2.4.21 (including 2.6.5 and 2.6.7, others not
> tested) produces the following errors quite often (once or twice per minute,
> with the corresponding delay) and the harddisk drops out of DMA.
Same here. 3 computers with PIIX4, 2 (or maybe even 3, need to check the
850M Conner too) different disks (all pre-udma but mwdma, 2.5G Seagate
Medalist and 850M WD Caviar). The common denominator seems to be PIIX
chip (PIIX3 and PIIX4 reported so far) and multiword DMA.
It came with 2.4.19 for me - 2.4.18 (and thus also Debian Woody) is fine
but anything with a newer kernel (incl. 2.6.*) is broken - DMA timeouts.
So maybe it is a little different (since your 2.4.20 works) but still
very similar.
--
Meelis Roos (mroos@linux.ee)
^ permalink raw reply [flat|nested] 7+ messages in thread
* IDE Timeout problem on Intel PIIX3 (Triton 2) chipset
@ 2004-06-28 12:48 Patrick Dreker
2004-06-28 20:21 ` Bartlomiej Zolnierkiewicz
0 siblings, 1 reply; 7+ messages in thread
From: Patrick Dreker @ 2004-06-28 12:48 UTC (permalink / raw)
To: linux-kernel
Hello...
Any kernel above and including 2.4.21 (including 2.6.5 and 2.6.7, others not
tested) produces the following errors quite often (once or twice per minute,
with the corresponding delay) and the harddisk drops out of DMA.
-------------------------------------------------
hda: dma_timer_expiry: dma status == 0x20
hda: timeout waiting for DMA
hda: timeout waiting for DMA
hda: (__ide_dma_test_irq) called while not waiting
hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
hda: drive not ready for command
-----------------------------------------------
I have checked that the drive and cable are OK (tested in another machine) and
no matter what drive I connect to the IDE controller, they *all* produce the
above error and drop DMA after some seconds.
Currently I am stuck at kernel version 2.4.20, as any later kernel severely
degrades the performance of the machine (Pentium Pro 200).
At http://www.uwsg.iu.edu/hypermail/linux/kernel/0304.1/0332.html I found a
thread which hints that IRQ sharing maybe the culprit, but /proc/interrupts
shows that the ide interrupt is not shared...
lspci and /proc/interrupts are included at the end of this mail.
What can I do to debug this problem?
Thanks,
Patrick
lspci:
-----------------------
0000:00:00.0 Host bridge: Intel Corp. 440FX - 82441FX PMC [Natoma] (rev 02)
0000:00:07.0 ISA bridge: Intel Corp. 82371SB PIIX3 ISA [Natoma/Triton II] (rev
01)
0000:00:07.1 IDE interface: Intel Corp. 82371SB PIIX3 IDE [Natoma/Triton II]
0000:00:0a.0 VGA compatible controller: Texas Instruments TVP4020 [Permedia 2]
(rev 01)
0000:00:0c.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
RTL-8139/8139C/8139C+ (rev 10)
0000:00:0d.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8029(AS)
--------------------------
/proc/interrupts:
-------------------------
CPU0
0: 55623224 IO-APIC-edge timer
1: 2 IO-APIC-edge keyboard
2: 0 XT-PIC cascade
8: 4 IO-APIC-edge rtc
10: 59404185 IO-APIC-level eth1
11: 64467911 IO-APIC-level eth0
14: 9031698 IO-APIC-edge ide0
NMI: 0
LOC: 55623074
ERR: 0
MIS: 13142
----------------------------
--
Patrick Dreker
GPG KeyID : 0xFCC2F7A7 (Patrick Dreker)
Fingerprint: 7A21 FC7F 707A C498 F370 1008 7044 66DA FCC2 F7A7
Key available from keyservers
^ permalink raw reply [flat|nested] 7+ messages in thread* Re: IDE Timeout problem on Intel PIIX3 (Triton 2) chipset
2004-06-28 12:48 Patrick Dreker
@ 2004-06-28 20:21 ` Bartlomiej Zolnierkiewicz
2004-06-28 23:25 ` Patrick Dreker
2004-06-29 14:48 ` Patrick Dreker
0 siblings, 2 replies; 7+ messages in thread
From: Bartlomiej Zolnierkiewicz @ 2004-06-28 20:21 UTC (permalink / raw)
To: Patrick Dreker; +Cc: linux-kernel
On Monday 28 of June 2004 14:48, Patrick Dreker wrote:
> Hello...
Hi,
> Any kernel above and including 2.4.21 (including 2.6.5 and 2.6.7, others
> not tested) produces the following errors quite often (once or twice per
> minute, with the corresponding delay) and the harddisk drops out of DMA.
>
> -------------------------------------------------
> hda: dma_timer_expiry: dma status == 0x20
> hda: timeout waiting for DMA
> hda: timeout waiting for DMA
> hda: (__ide_dma_test_irq) called while not waiting
> hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
>
> hda: drive not ready for command
> -----------------------------------------------
>
> I have checked that the drive and cable are OK (tested in another machine)
> and no matter what drive I connect to the IDE controller, they *all*
> produce the above error and drop DMA after some seconds.
>
> Currently I am stuck at kernel version 2.4.20, as any later kernel severely
> degrades the performance of the machine (Pentium Pro 200).
>
> At http://www.uwsg.iu.edu/hypermail/linux/kernel/0304.1/0332.html I found a
> thread which hints that IRQ sharing maybe the culprit, but /proc/interrupts
> shows that the ide interrupt is not shared...
This was HPT specific problem.
> lspci and /proc/interrupts are included at the end of this mail.
>
> What can I do to debug this problem?
"diff -u" on "lspci -s 07.1 -xxx" outputs for 2.4.20 and 2.4.21 kernels.
Doing bisection search on 2.4.21-pre kernels would also help.
> Thanks,
> Patrick
>
> lspci:
> -----------------------
> 0000:00:00.0 Host bridge: Intel Corp. 440FX - 82441FX PMC [Natoma] (rev 02)
> 0000:00:07.0 ISA bridge: Intel Corp. 82371SB PIIX3 ISA [Natoma/Triton II]
> (rev 01)
> 0000:00:07.1 IDE interface: Intel Corp. 82371SB PIIX3 IDE [Natoma/Triton
> II] 0000:00:0a.0 VGA compatible controller: Texas Instruments TVP4020
> [Permedia 2] (rev 01)
> 0000:00:0c.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
> RTL-8139/8139C/8139C+ (rev 10)
> 0000:00:0d.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
> RTL-8029(AS) --------------------------
>
> /proc/interrupts:
> -------------------------
> CPU0
> 0: 55623224 IO-APIC-edge timer
> 1: 2 IO-APIC-edge keyboard
> 2: 0 XT-PIC cascade
> 8: 4 IO-APIC-edge rtc
> 10: 59404185 IO-APIC-level eth1
> 11: 64467911 IO-APIC-level eth0
> 14: 9031698 IO-APIC-edge ide0
> NMI: 0
> LOC: 55623074
> ERR: 0
> MIS: 13142
> ----------------------------
^ permalink raw reply [flat|nested] 7+ messages in thread* Re: IDE Timeout problem on Intel PIIX3 (Triton 2) chipset
2004-06-28 20:21 ` Bartlomiej Zolnierkiewicz
@ 2004-06-28 23:25 ` Patrick Dreker
2004-06-29 14:48 ` Patrick Dreker
1 sibling, 0 replies; 7+ messages in thread
From: Patrick Dreker @ 2004-06-28 23:25 UTC (permalink / raw)
To: linux-kernel; +Cc: Bartlomiej Zolnierkiewicz
Am Montag, 28. Juni 2004 22:21 schrieb Bartlomiej Zolnierkiewicz:
> On Monday 28 of June 2004 14:48, Patrick Dreker wrote:
> > What can I do to debug this problem?
> "diff -u" on "lspci -s 07.1 -xxx" outputs for 2.4.20 and 2.4.21 kernels.
>
> Doing bisection search on 2.4.21-pre kernels would also help.
I will do the bisection search first and then post the lspci diff between the
last working revision and the first non-working version as I have to
recompile everything anyways.
Thanks,
Patrick
--
Patrick Dreker
GPG KeyID : 0xFCC2F7A7 (Patrick Dreker)
Fingerprint: 7A21 FC7F 707A C498 F370 1008 7044 66DA FCC2 F7A7
Key available from keyservers
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: IDE Timeout problem on Intel PIIX3 (Triton 2) chipset
2004-06-28 20:21 ` Bartlomiej Zolnierkiewicz
2004-06-28 23:25 ` Patrick Dreker
@ 2004-06-29 14:48 ` Patrick Dreker
1 sibling, 0 replies; 7+ messages in thread
From: Patrick Dreker @ 2004-06-29 14:48 UTC (permalink / raw)
To: Bartlomiej Zolnierkiewicz; +Cc: linux-kernel
Am Montag, 28. Juni 2004 22:21 schrieb Bartlomiej Zolnierkiewicz:
> > What can I do to debug this problem?
> "diff -u" on "lspci -s 07.1 -xxx" outputs for 2.4.20 and 2.4.21 kernels.
>
> Doing bisection search on 2.4.21-pre kernels would also help.
2.4.21-pre1 is the first non-working kernel, 2.4.20 works. When generating the
configs for 2.4.21-pre1 (make oldconfig based on the working 2.4.20 config) I
was asked "Use IDE Taskfile I/O" which defaulted to no and I kept that
default (i.e. "Don't use Taskfile I/O").
lspci -s 07.1 -xxx shows no difference between a working (2.4.20) kernel and a
non-working (2.4.21-pre1) kernel.
This caught my eye, but was probably obvious to you:
2.4.21-pre1 reports IDE Version 7.00beta-2.4 while 2.4.20 reports version 6.31
Patrick
--
Patrick Dreker
GPG KeyID : 0xFCC2F7A7 (Patrick Dreker)
Fingerprint: 7A21 FC7F 707A C498 F370 1008 7044 66DA FCC2 F7A7
Key available from keyservers
^ permalink raw reply [flat|nested] 7+ messages in thread
end of thread, other threads:[~2004-06-29 14:48 UTC | newest]
Thread overview: 7+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2004-06-28 20:27 IDE Timeout problem on Intel PIIX3 (Triton 2) chipset Chris Rankin
2004-06-29 1:21 ` Patrick Dreker
[not found] <E1Bevgk-0007jR-4F@rhn.tartu-labor>
2004-06-28 18:47 ` Meelis Roos
-- strict thread matches above, loose matches on Subject: below --
2004-06-28 12:48 Patrick Dreker
2004-06-28 20:21 ` Bartlomiej Zolnierkiewicz
2004-06-28 23:25 ` Patrick Dreker
2004-06-29 14:48 ` Patrick Dreker
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.