* Asus A8V , via vt8251 AHCI
@ 2005-11-01 6:40 Don Carroll
2005-11-01 15:40 ` Randy.Dunlap
0 siblings, 1 reply; 13+ messages in thread
From: Don Carroll @ 2005-11-01 6:40 UTC (permalink / raw)
To: garzik, linux-ide
Hi , I added pci id 3349 to achi.c and I get it to load now
ahci version 1.00
ACPI: PCI Interrupt 0000:00:0f.0[B] -> GSI 21 (level, low) -> IRQ 217
PCI: Via IRQ fixup for 0000:00:0f.0, from 10 to 9
ahci(0000:00:0f.0) AHCI 0001.0000 32 slots 4 ports 3 Gbps 0xf impl SATA mode
ahci(0000:00:0f.0) flags: 64bit ncq pm led clo pmp pio slum part
ata3: SATA max UDMA/133 cmd 0xFFFFC20000038900 ctl 0x0 bmdma 0x0 irq 217
ata4: SATA max UDMA/133 cmd 0xFFFFC20000038980 ctl 0x0 bmdma 0x0 irq 217
ata5: SATA max UDMA/133 cmd 0xFFFFC20000038A00 ctl 0x0 bmdma 0x0 irq 217
ata6: SATA max UDMA/133 cmd 0xFFFFC20000038A80 ctl 0x0 bmdma 0x0 irq 217
ata3: no device found (phy stat 00000000)
scsi2 : ahci
ata4: no device found (phy stat 00000000)
scsi3 : ahci
ata5: no device found (phy stat 00000000)
scsi4 : ahci
ata6 is slow to respond, please be patient
ata6 failed to respond (30 secs)
scsi5 : ahci
I have a drive on ata6 , but it does not respond , timesout
this is Mandriva 2006 x86_64 and it has 2.6.12 I have not been able to get .14
to compile yet , does this look like something that ahci 1.01 would help , any
ideas ?
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: Asus A8V , via vt8251 AHCI
2005-11-01 6:40 Asus A8V , via vt8251 AHCI Don Carroll
@ 2005-11-01 15:40 ` Randy.Dunlap
[not found] ` <20051101192449.GA9719@vcr.star-c.com>
0 siblings, 1 reply; 13+ messages in thread
From: Randy.Dunlap @ 2005-11-01 15:40 UTC (permalink / raw)
To: ibedonc; +Cc: jgarzik, linux-ide
On Tue, 1 Nov 2005, Don Carroll wrote:
> Hi , I added pci id 3349 to achi.c and I get it to load now
> ahci version 1.00
> ACPI: PCI Interrupt 0000:00:0f.0[B] -> GSI 21 (level, low) -> IRQ 217
> PCI: Via IRQ fixup for 0000:00:0f.0, from 10 to 9
> ahci(0000:00:0f.0) AHCI 0001.0000 32 slots 4 ports 3 Gbps 0xf impl SATA mode
> ahci(0000:00:0f.0) flags: 64bit ncq pm led clo pmp pio slum part
> ata3: SATA max UDMA/133 cmd 0xFFFFC20000038900 ctl 0x0 bmdma 0x0 irq 217
> ata4: SATA max UDMA/133 cmd 0xFFFFC20000038980 ctl 0x0 bmdma 0x0 irq 217
> ata5: SATA max UDMA/133 cmd 0xFFFFC20000038A00 ctl 0x0 bmdma 0x0 irq 217
> ata6: SATA max UDMA/133 cmd 0xFFFFC20000038A80 ctl 0x0 bmdma 0x0 irq 217
> ata3: no device found (phy stat 00000000)
> scsi2 : ahci
> ata4: no device found (phy stat 00000000)
> scsi3 : ahci
> ata5: no device found (phy stat 00000000)
> scsi4 : ahci
> ata6 is slow to respond, please be patient
> ata6 failed to respond (30 secs)
> scsi5 : ahci
>
> I have a drive on ata6 , but it does not respond , timesout
>
> this is Mandriva 2006 x86_64 and it has 2.6.12 I have not been able to get .14
> to compile yet , does this look like something that ahci 1.01 would help , any
> ideas ?
Yes.
(a) boot with "irqpoll" added to the kernel command line to see
if the kernel can route the missed interrupts.
different test:
(b) Disable CONFIG_PCI_MSI and reboot/retest (without "irqpoll").
and report the results of those.
What are your configs for SMP and APIC options?
--
~Randy
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: Asus A8V , via vt8251 AHCI
[not found] ` <20051101192449.GA9719@vcr.star-c.com>
@ 2005-11-01 20:42 ` Randy.Dunlap
2005-11-02 0:39 ` Don Carroll
2005-11-02 3:41 ` Don Carroll
0 siblings, 2 replies; 13+ messages in thread
From: Randy.Dunlap @ 2005-11-01 20:42 UTC (permalink / raw)
To: ibedonc; +Cc: linux-ide, Randy.Dunlap
Please don't drop cc's and/or to's.
Back to the mailing list now...
On Tue, 1 Nov 2005, Don Carroll wrote:
> kernel = Mandriva default Linux vcr.star-c.com 2.6.12-12mdksmp #1 SMP Fri Sep 9
> 17:20:34 CEST 2005 x86_64 AMD Athlon(tm) 64 X2 Dual Core Processor 3800+
> unknown GNU/Linux
> attaching default config for mandriva linux , I just edited the ahci.c and
> built the module from that , did not do a complete kernel install
The default config is uniprocessor, not SMP. But your kernel
verison string above says SMP...
In either case it looks like it is using local APIC and IO APIC.
That's all that's required to cause the problem that I am
familiar with.
You can at least do test (a) below (boot with the "irqpoll"
option on the kernel command line) and report on that.
(without rebuilding the kernel)
Test (b) requires rebuilding the kernel, which is going
to be needed to fix this problem (if I'm right about it).
> On Tue, Nov 01, 2005 at 07:40:06AM -0800, Randy.Dunlap wrote:
> > On Tue, 1 Nov 2005, Don Carroll wrote:
> >
> > > Hi , I added pci id 3349 to achi.c and I get it to load now
> > > ahci version 1.00
> > > ACPI: PCI Interrupt 0000:00:0f.0[B] -> GSI 21 (level, low) -> IRQ 217
> > > PCI: Via IRQ fixup for 0000:00:0f.0, from 10 to 9
> > > ahci(0000:00:0f.0) AHCI 0001.0000 32 slots 4 ports 3 Gbps 0xf impl SATA mode
> > > ahci(0000:00:0f.0) flags: 64bit ncq pm led clo pmp pio slum part
> > > ata3: SATA max UDMA/133 cmd 0xFFFFC20000038900 ctl 0x0 bmdma 0x0 irq 217
> > > ata4: SATA max UDMA/133 cmd 0xFFFFC20000038980 ctl 0x0 bmdma 0x0 irq 217
> > > ata5: SATA max UDMA/133 cmd 0xFFFFC20000038A00 ctl 0x0 bmdma 0x0 irq 217
> > > ata6: SATA max UDMA/133 cmd 0xFFFFC20000038A80 ctl 0x0 bmdma 0x0 irq 217
> > > ata3: no device found (phy stat 00000000)
> > > scsi2 : ahci
> > > ata4: no device found (phy stat 00000000)
> > > scsi3 : ahci
> > > ata5: no device found (phy stat 00000000)
> > > scsi4 : ahci
> > > ata6 is slow to respond, please be patient
> > > ata6 failed to respond (30 secs)
> > > scsi5 : ahci
> > >
> > > I have a drive on ata6 , but it does not respond , timesout
> > >
> > > this is Mandriva 2006 x86_64 and it has 2.6.12 I have not been able to get .14
> > > to compile yet , does this look like something that ahci 1.01 would help , any
> > > ideas ?
> >
> > Yes.
> > (a) boot with "irqpoll" added to the kernel command line to see
> > if the kernel can route the missed interrupts.
> >
> > different test:
> > (b) Disable CONFIG_PCI_MSI and reboot/retest (without "irqpoll").
> >
> > and report the results of those.
> >
> > What are your configs for SMP and APIC options?
> >
> > --
> > ~Randy
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: Asus A8V , via vt8251 AHCI
2005-11-01 20:42 ` Randy.Dunlap
@ 2005-11-02 0:39 ` Don Carroll
2005-11-02 3:41 ` Don Carroll
1 sibling, 0 replies; 13+ messages in thread
From: Don Carroll @ 2005-11-02 0:39 UTC (permalink / raw)
To: Randy.Dunlap; +Cc: linux-ide
I am at work , will do the tests when I get home
thanks for your help
On Tue, Nov 01, 2005 at 12:42:02PM -0800, Randy.Dunlap wrote:
>
> Please don't drop cc's and/or to's.
> Back to the mailing list now...
>
> On Tue, 1 Nov 2005, Don Carroll wrote:
>
> > kernel = Mandriva default Linux vcr.star-c.com 2.6.12-12mdksmp #1 SMP Fri Sep 9
> > 17:20:34 CEST 2005 x86_64 AMD Athlon(tm) 64 X2 Dual Core Processor 3800+
> > unknown GNU/Linux
> > attaching default config for mandriva linux , I just edited the ahci.c and
> > built the module from that , did not do a complete kernel install
>
> The default config is uniprocessor, not SMP. But your kernel
> verison string above says SMP...
>
> In either case it looks like it is using local APIC and IO APIC.
> That's all that's required to cause the problem that I am
> familiar with.
>
> You can at least do test (a) below (boot with the "irqpoll"
> option on the kernel command line) and report on that.
> (without rebuilding the kernel)
>
> Test (b) requires rebuilding the kernel, which is going
> to be needed to fix this problem (if I'm right about it).
>
>
> > On Tue, Nov 01, 2005 at 07:40:06AM -0800, Randy.Dunlap wrote:
> > > On Tue, 1 Nov 2005, Don Carroll wrote:
> > >
> > > > Hi , I added pci id 3349 to achi.c and I get it to load now
> > > > ahci version 1.00
> > > > ACPI: PCI Interrupt 0000:00:0f.0[B] -> GSI 21 (level, low) -> IRQ 217
> > > > PCI: Via IRQ fixup for 0000:00:0f.0, from 10 to 9
> > > > ahci(0000:00:0f.0) AHCI 0001.0000 32 slots 4 ports 3 Gbps 0xf impl SATA mode
> > > > ahci(0000:00:0f.0) flags: 64bit ncq pm led clo pmp pio slum part
> > > > ata3: SATA max UDMA/133 cmd 0xFFFFC20000038900 ctl 0x0 bmdma 0x0 irq 217
> > > > ata4: SATA max UDMA/133 cmd 0xFFFFC20000038980 ctl 0x0 bmdma 0x0 irq 217
> > > > ata5: SATA max UDMA/133 cmd 0xFFFFC20000038A00 ctl 0x0 bmdma 0x0 irq 217
> > > > ata6: SATA max UDMA/133 cmd 0xFFFFC20000038A80 ctl 0x0 bmdma 0x0 irq 217
> > > > ata3: no device found (phy stat 00000000)
> > > > scsi2 : ahci
> > > > ata4: no device found (phy stat 00000000)
> > > > scsi3 : ahci
> > > > ata5: no device found (phy stat 00000000)
> > > > scsi4 : ahci
> > > > ata6 is slow to respond, please be patient
> > > > ata6 failed to respond (30 secs)
> > > > scsi5 : ahci
> > > >
> > > > I have a drive on ata6 , but it does not respond , timesout
> > > >
> > > > this is Mandriva 2006 x86_64 and it has 2.6.12 I have not been able to get .14
> > > > to compile yet , does this look like something that ahci 1.01 would help , any
> > > > ideas ?
> > >
> > > Yes.
> > > (a) boot with "irqpoll" added to the kernel command line to see
> > > if the kernel can route the missed interrupts.
> > >
> > > different test:
> > > (b) Disable CONFIG_PCI_MSI and reboot/retest (without "irqpoll").
> > >
> > > and report the results of those.
> > >
> > > What are your configs for SMP and APIC options?
> > >
> > > --
> > > ~Randy
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: Asus A8V , via vt8251 AHCI
2005-11-01 20:42 ` Randy.Dunlap
2005-11-02 0:39 ` Don Carroll
@ 2005-11-02 3:41 ` Don Carroll
2005-11-02 3:57 ` Randy.Dunlap
1 sibling, 1 reply; 13+ messages in thread
From: Don Carroll @ 2005-11-02 3:41 UTC (permalink / raw)
To: Randy.Dunlap, linux-ide
[-- Attachment #1: Type: text/plain, Size: 3024 bytes --]
well , I have 2.6.14 running , did fix my lost timer tick problem (another
issue) but no go on it with irqpoll , recompiling now without MSI, I am
attaching a dmesg output
On Tue, Nov 01, 2005 at 12:42:02PM -0800, Randy.Dunlap wrote:
>
> Please don't drop cc's and/or to's.
> Back to the mailing list now...
>
> On Tue, 1 Nov 2005, Don Carroll wrote:
>
> > kernel = Mandriva default Linux vcr.star-c.com 2.6.12-12mdksmp #1 SMP Fri Sep 9
> > 17:20:34 CEST 2005 x86_64 AMD Athlon(tm) 64 X2 Dual Core Processor 3800+
> > unknown GNU/Linux
> > attaching default config for mandriva linux , I just edited the ahci.c and
> > built the module from that , did not do a complete kernel install
>
> The default config is uniprocessor, not SMP. But your kernel
> verison string above says SMP...
>
> In either case it looks like it is using local APIC and IO APIC.
> That's all that's required to cause the problem that I am
> familiar with.
>
> You can at least do test (a) below (boot with the "irqpoll"
> option on the kernel command line) and report on that.
> (without rebuilding the kernel)
>
> Test (b) requires rebuilding the kernel, which is going
> to be needed to fix this problem (if I'm right about it).
>
>
> > On Tue, Nov 01, 2005 at 07:40:06AM -0800, Randy.Dunlap wrote:
> > > On Tue, 1 Nov 2005, Don Carroll wrote:
> > >
> > > > Hi , I added pci id 3349 to achi.c and I get it to load now
> > > > ahci version 1.00
> > > > ACPI: PCI Interrupt 0000:00:0f.0[B] -> GSI 21 (level, low) -> IRQ 217
> > > > PCI: Via IRQ fixup for 0000:00:0f.0, from 10 to 9
> > > > ahci(0000:00:0f.0) AHCI 0001.0000 32 slots 4 ports 3 Gbps 0xf impl SATA mode
> > > > ahci(0000:00:0f.0) flags: 64bit ncq pm led clo pmp pio slum part
> > > > ata3: SATA max UDMA/133 cmd 0xFFFFC20000038900 ctl 0x0 bmdma 0x0 irq 217
> > > > ata4: SATA max UDMA/133 cmd 0xFFFFC20000038980 ctl 0x0 bmdma 0x0 irq 217
> > > > ata5: SATA max UDMA/133 cmd 0xFFFFC20000038A00 ctl 0x0 bmdma 0x0 irq 217
> > > > ata6: SATA max UDMA/133 cmd 0xFFFFC20000038A80 ctl 0x0 bmdma 0x0 irq 217
> > > > ata3: no device found (phy stat 00000000)
> > > > scsi2 : ahci
> > > > ata4: no device found (phy stat 00000000)
> > > > scsi3 : ahci
> > > > ata5: no device found (phy stat 00000000)
> > > > scsi4 : ahci
> > > > ata6 is slow to respond, please be patient
> > > > ata6 failed to respond (30 secs)
> > > > scsi5 : ahci
> > > >
> > > > I have a drive on ata6 , but it does not respond , timesout
> > > >
> > > > this is Mandriva 2006 x86_64 and it has 2.6.12 I have not been able to get .14
> > > > to compile yet , does this look like something that ahci 1.01 would help , any
> > > > ideas ?
> > >
> > > Yes.
> > > (a) boot with "irqpoll" added to the kernel command line to see
> > > if the kernel can route the missed interrupts.
> > >
> > > different test:
> > > (b) Disable CONFIG_PCI_MSI and reboot/retest (without "irqpoll").
> > >
> > > and report the results of those.
> > >
> > > What are your configs for SMP and APIC options?
> > >
> > > --
> > > ~Randy
[-- Attachment #2: dmesg.txt --]
[-- Type: text/plain, Size: 15567 bytes --]
Bootdata ok (command line is root=/dev/sda1 resume=/dev/sda5)
Linux version 2.6.14 (root@vcr.star-c.com) (gcc version 4.0.1 (4.0.1-5mdk for Mandriva Linux release 2006.0)) #1 SMP Tue Nov 1 16:49:27 CST 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000007bfb0000 (usable)
BIOS-e820: 000000007bfb0000 - 000000007bfbe000 (ACPI data)
BIOS-e820: 000000007bfbe000 - 000000007bfe0000 (ACPI NVS)
BIOS-e820: 000000007bfe0000 - 000000007c000000 (reserved)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000ff7c0000 - 0000000100000000 (reserved)
ACPI: RSDP (v002 ACPIAM ) @ 0x00000000000fac60
ACPI: XSDT (v001 A M I OEMXSDT 0x09000505 MSFT 0x00000097) @ 0x000000007bfb0100
ACPI: FADT (v003 A M I OEMFACP 0x09000505 MSFT 0x00000097) @ 0x000000007bfb0290
ACPI: MADT (v001 A M I OEMAPIC 0x09000505 MSFT 0x00000097) @ 0x000000007bfb0390
ACPI: OEMB (v001 A M I AMI_OEM 0x09000505 MSFT 0x00000097) @ 0x000000007bfbe040
ACPI: DSDT (v001 A0347 A0347001 0x00000001 INTL 0x02002026) @ 0x0000000000000000
Scanning NUMA topology in Northbridge 24
Number of nodes 1
Node 0 MemBase 0000000000000000 Limit 000000007bfb0000
Using 20 for the hash shift. Max adder is 7bfb0000
Using node hash shift of 20
Bootmem setup node 0 0000000000000000-000000007bfb0000
On node 0 totalpages: 507727
DMA zone: 3999 pages, LIFO batch:1
Normal zone: 503728 pages, LIFO batch:31
HighMem zone: 0 pages, LIFO batch:1
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:3 APIC version 16
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1 15:3 APIC version 16
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Setting APIC routing to flat
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 80000000 (gap: 7c000000:64000000)
Checking aperture...
CPU 0: aperture @ d4000000 size 64 MB
Built 1 zonelists
Kernel command line: root=/dev/sda1 resume=/dev/sda5
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 131072 bytes)
time.c: Using 3.579545 MHz PM timer.
time.c: Detected 2000.184 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
Memory: 1995856k/2031296k available (2150k kernel code, 35052k reserved, 757k data, 232k init)
Calibrating delay using timer specific routine.. 4007.40 BogoMIPS (lpj=8014802)
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU 0(2) -> Node 0 -> Core 0
mtrr: v2.0 (20020519)
Using local APIC timer interrupts.
Detected 12.501 MHz APIC timer.
softlockup thread 0 started up.
Booting processor 1/2 APIC 0x1
Initializing CPU#1
Calibrating delay using timer specific routine.. 4000.53 BogoMIPS (lpj=8001072)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU 1(2) -> Node 0 -> Core 1
AMD Athlon(tm) 64 X2 Dual Core Processor 3800+ stepping 02
CPU 1: Syncing TSC to CPU 0.
CPU 1: synchronized TSC with CPU 0 (last diff -77 cycles, maxerr 545 cycles)
Brought up 2 CPUs
softlockup thread 1 started up.
Disabling vsyscall due to use of PM timer
time.c: Using PM based timekeeping.
testing NMI watchdog ... OK.
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using configuration type 1
ACPI: Subsystem revision 20050902
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:00:0b.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P7._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P7.P7P9._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P7.P7P8._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs *3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI: Cannot allocate resource region 0 of device 0000:01:00.0
PCI: Cannot allocate resource region 1 of device 0000:01:00.0
agpgart: Detected AGP bridge 0
agpgart: AGP aperture is 64M @ 0xd4000000
PCI-DMA: Disabling IOMMU.
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: fa900000-fc9fffff
PREFETCH window: bff00000-c7efffff
PCI: Bridge: 0000:02:00.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:02:00.1
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:13.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Setting latency timer of device 0000:00:01.0 to 64
PCI: Setting latency timer of device 0000:00:13.0 to 64
PCI: Setting latency timer of device 0000:02:00.0 to 64
PCI: Setting latency timer of device 0000:02:00.1 to 64
IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $
audit: initializing netlink socket (disabled)
audit(1130901941.132:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
Initializing Cryptographic API
PCI: Setting latency timer of device 0000:02:00.0 to 64
pcie_portdrv_probe->Dev[287c:1106] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[pcie00]
PCI: Setting latency timer of device 0000:02:00.1 to 64
pcie_portdrv_probe->Dev[287d:1106] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[pcie00]
Real Time Clock Driver v1.12
Linux agpgart interface v0.101 (c) Dave Jones
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 32000K size 1024 blocksize
pktcdvd: v0.2.0a 2004-07-14 Jens Axboe (axboe@suse.de) and petero2@telia.com
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:0f.1
PCI: Via IRQ fixup for 0000:00:0f.1, from 255 to 0
VP_IDE: chipset revision 7
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: Unknown VIA SouthBridge, disabling DMA.
VP_IDE: IDE controller at PCI slot 0000:00:0f.1
VP_IDE: chipset revision 7
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: Unknown VIA SouthBridge, disabling DMA.
mice: PS/2 mouse device common for all mice
md: md driver 0.90.2 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 3.39
NET: Registered protocol family 2
input: AT Translated Set 2 keyboard on isa0060/serio0
IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
BIOS EDD facility v0.16 2004-Jun-25, 2 devices found
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
SCSI subsystem initialized
libata version 1.12 loaded.
sata_sil version 0.9
ACPI: PCI Interrupt 0000:00:0c.0[A] -> GSI 17 (level, low) -> IRQ 193
ata1: SATA max UDMA/100 cmd 0xFFFFC20000004C80 ctl 0xFFFFC20000004C8A bmdma 0xFFFFC20000004C00 irq 193
ata2: SATA max UDMA/100 cmd 0xFFFFC20000004CC0 ctl 0xFFFFC20000004CCA bmdma 0xFFFFC20000004C08 irq 193
input: ImPS/2 Generic Wheel Mouse on isa0060/serio1
ata1: no device found (phy stat 00000000)
scsi0 : sata_sil
ata2: dev 0 cfg 49:2f00 82:74eb 83:7fea 84:4023 85:74e9 86:3c02 87:4023 88:203f
ata2: dev 0 ATA, max UDMA/100, 488397168 sectors: lba48
ata2: dev 0 configured for UDMA/100
scsi1 : sata_sil
Vendor: ATA Model: HDS722525VLSA80 Rev: V36O
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
SCSI device sda: drive cache: write back
sda: sda1 sda2 < sda5 sda6 sda7 >
Attached scsi disk sda at scsi1, channel 0, id 0, lun 0
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 232k freed
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.3
ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 20 (level, low) -> IRQ 201
PCI: Via IRQ fixup for 0000:00:10.0, from 11 to 9
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:10.0: irq 201, io base 0x0000d480
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.1[C] -> GSI 22 (level, low) -> IRQ 209
PCI: Via IRQ fixup for 0000:00:10.1, from 5 to 1
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.1: irq 209, io base 0x0000d400
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 217
PCI: Via IRQ fixup for 0000:00:10.2, from 10 to 9
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.2: irq 217, io base 0x0000d080
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.3[D] -> GSI 23 (level, low) -> IRQ 225
PCI: Via IRQ fixup for 0000:00:10.3, from 3 to 1
uhci_hcd 0000:00:10.3: UHCI Host Controller
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.3: irq 225, io base 0x0000d000
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.4[C] -> GSI 22 (level, low) -> IRQ 209
PCI: Via IRQ fixup for 0000:00:10.4, from 5 to 1
ehci_hcd 0000:00:10.4: EHCI Host Controller
ehci_hcd 0000:00:10.4: debug port 1
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:10.4: irq 209, io mem 0xfebdf400
ehci_hcd 0000:00:10.4: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
ts: Compaq touchscreen protocol output
ACPI: Power Button (FF) [PWRF]
ACPI: Sleep Button (CM) [SLPB]
ACPI: Power Button (CM) [PWRB]
ibm_acpi: ec object not found
ACPI: CPU0 (power states: C1[C1])
ACPI: Processor [CPU1] (supports 16 throttling states)
ACPI: CPU1 (power states: C1[C1])
EXT3 FS on sda1, internal journal
Adding 2939852k swap on /dev/sda5. Priority:-1 extents:1 across:2939852k
Linux video capture interface: v1.00
bttv: driver version 0.9.16 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
Probing IDE interface ide0...
Probing IDE interface ide1...
hdc: TDK DVDRW0404N, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
ahci version 1.01
ACPI: PCI Interrupt 0000:00:0f.0[B] -> GSI 21 (level, low) -> IRQ 217
PCI: Via IRQ fixup for 0000:00:0f.0, from 10 to 9
ahci(0000:00:0f.0) AHCI 0001.0000 32 slots 4 ports 3 Gbps 0xf impl SATA mode
ahci(0000:00:0f.0) flags: 64bit ncq pm led clo pmp pio slum part
ata3: SATA max UDMA/133 cmd 0xFFFFC20000020900 ctl 0x0 bmdma 0x0 irq 233
ata4: SATA max UDMA/133 cmd 0xFFFFC20000020980 ctl 0x0 bmdma 0x0 irq 233
ata5: SATA max UDMA/133 cmd 0xFFFFC20000020A00 ctl 0x0 bmdma 0x0 irq 233
ata6: SATA max UDMA/133 cmd 0xFFFFC20000020A80 ctl 0x0 bmdma 0x0 irq 233
ata3: no device found (phy stat 00000000)
scsi2 : ahci
ata4: no device found (phy stat 00000000)
scsi3 : ahci
ata5: no device found (phy stat 00000000)
scsi4 : ahci
ata6 is slow to respond, please be patient
ata6 failed to respond (30 secs)
scsi5 : ahci
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
loop: loaded (max 8 devices)
hdc: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache
Uniform CD-ROM driver Revision: 3.20
floppy0: no floppy controllers found
floppy0: no floppy controllers found
NET: Registered protocol family 17
via-rhine.c:v1.10-LK1.2.0-2.6 June-10-2004 Written by Donald Becker
ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 23 (level, low) -> IRQ 225
PCI: Via IRQ fixup for 0000:00:12.0, from 11 to 1
eth0: VIA Rhine II at 0x1c400, 00:13:d4:a7:d6:43, IRQ 225.
eth0: MII PHY found at address 1, status 0x786d advertising 01e1 Link 40a1.
eth0: link up, 100Mbps, half-duplex, lpa 0x40A1
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP]
parport0: irq 7 detected
parport0: Printer, Hewlett-Packard HP LaserJet 6L
lp0: using parport0 (polling).
lp0: console ready
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
via82xx: Assuming DXS channels with 48k fixed sample rate.
Please try dxs_support=5 option
and report if it works on your machine.
For more details, read ALSA-Configuration.txt.
ACPI: PCI Interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 209
PCI: Via IRQ fixup for 0000:00:11.5, from 5 to 1
PCI: Setting latency timer of device 0000:00:11.5 to 64
cdrom: This disc doesn't have any tracks I recognize!
NET: Registered protocol family 10
Disabled Privacy Extensions on device ffffffff80395700(lo)
IPv6 over IPv4 tunneling driver
eth0: no IPv6 routers present
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
NFSD: recovery directory /var/lib/nfs/v4recovery doesn't exist
NFSD: starting 90-second grace period
powernow-k8: Found 2 AMD Athlon 64 / Opteron processors (version 1.50.4)
powernow-k8: 0 : fid 0xc (2000 MHz), vid 0x8 (1350 mV)
powernow-k8: 1 : fid 0xa (1800 MHz), vid 0xa (1300 mV)
powernow-k8: 2 : fid 0x2 (1000 MHz), vid 0x12 (1100 mV)
cpu_init done, current fid 0xc, vid 0x8
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: Asus A8V , via vt8251 AHCI
2005-11-02 3:41 ` Don Carroll
@ 2005-11-02 3:57 ` Randy.Dunlap
2005-11-02 4:36 ` Don Carroll
2005-11-02 4:47 ` Asus A8V , via vt8251 AHCI Don Carroll
0 siblings, 2 replies; 13+ messages in thread
From: Randy.Dunlap @ 2005-11-02 3:57 UTC (permalink / raw)
Cc: ibedonc, linux-ide
On Tue, 1 Nov 2005 21:41:51 -0600 Don Carroll wrote:
> well , I have 2.6.14 running , did fix my lost timer tick problem (another
> issue) but no go on it with irqpoll , recompiling now without MSI, I am
> attaching a dmesg output
This boot log isn't the one where you tried irqpoll, right?
I.e., it doesn't show that in the message log.
> On Tue, Nov 01, 2005 at 12:42:02PM -0800, Randy.Dunlap wrote:
> >
> > Please don't drop cc's and/or to's.
> > Back to the mailing list now...
> >
> > On Tue, 1 Nov 2005, Don Carroll wrote:
> >
> > > kernel = Mandriva default Linux vcr.star-c.com 2.6.12-12mdksmp #1 SMP Fri Sep 9
> > > 17:20:34 CEST 2005 x86_64 AMD Athlon(tm) 64 X2 Dual Core Processor 3800+
> > > unknown GNU/Linux
> > > attaching default config for mandriva linux , I just edited the ahci.c and
> > > built the module from that , did not do a complete kernel install
> >
> > The default config is uniprocessor, not SMP. But your kernel
> > verison string above says SMP...
> >
> > In either case it looks like it is using local APIC and IO APIC.
> > That's all that's required to cause the problem that I am
> > familiar with.
> >
> > You can at least do test (a) below (boot with the "irqpoll"
> > option on the kernel command line) and report on that.
> > (without rebuilding the kernel)
> >
> > Test (b) requires rebuilding the kernel, which is going
> > to be needed to fix this problem (if I'm right about it).
> >
> >
> > > On Tue, Nov 01, 2005 at 07:40:06AM -0800, Randy.Dunlap wrote:
> > > > On Tue, 1 Nov 2005, Don Carroll wrote:
> > > >
> > > > > Hi , I added pci id 3349 to achi.c and I get it to load now
> > > > > ahci version 1.00
> > > > > ACPI: PCI Interrupt 0000:00:0f.0[B] -> GSI 21 (level, low) -> IRQ 217
> > > > > PCI: Via IRQ fixup for 0000:00:0f.0, from 10 to 9
> > > > > ahci(0000:00:0f.0) AHCI 0001.0000 32 slots 4 ports 3 Gbps 0xf impl SATA mode
> > > > > ahci(0000:00:0f.0) flags: 64bit ncq pm led clo pmp pio slum part
> > > > > ata3: SATA max UDMA/133 cmd 0xFFFFC20000038900 ctl 0x0 bmdma 0x0 irq 217
> > > > > ata4: SATA max UDMA/133 cmd 0xFFFFC20000038980 ctl 0x0 bmdma 0x0 irq 217
> > > > > ata5: SATA max UDMA/133 cmd 0xFFFFC20000038A00 ctl 0x0 bmdma 0x0 irq 217
> > > > > ata6: SATA max UDMA/133 cmd 0xFFFFC20000038A80 ctl 0x0 bmdma 0x0 irq 217
> > > > > ata3: no device found (phy stat 00000000)
> > > > > scsi2 : ahci
> > > > > ata4: no device found (phy stat 00000000)
> > > > > scsi3 : ahci
> > > > > ata5: no device found (phy stat 00000000)
> > > > > scsi4 : ahci
> > > > > ata6 is slow to respond, please be patient
> > > > > ata6 failed to respond (30 secs)
> > > > > scsi5 : ahci
> > > > >
> > > > > I have a drive on ata6 , but it does not respond , timesout
> > > > >
> > > > > this is Mandriva 2006 x86_64 and it has 2.6.12 I have not been able to get .14
> > > > > to compile yet , does this look like something that ahci 1.01 would help , any
> > > > > ideas ?
> > > >
> > > > Yes.
> > > > (a) boot with "irqpoll" added to the kernel command line to see
> > > > if the kernel can route the missed interrupts.
> > > >
> > > > different test:
> > > > (b) Disable CONFIG_PCI_MSI and reboot/retest (without "irqpoll").
> > > >
> > > > and report the results of those.
> > > >
> > > > What are your configs for SMP and APIC options?
> > > >
> > > > --
> > > > ~Randy
>
---
~Randy
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: Asus A8V , via vt8251 AHCI
2005-11-02 3:57 ` Randy.Dunlap
@ 2005-11-02 4:36 ` Don Carroll
2005-11-02 4:56 ` Randy.Dunlap
2005-11-02 4:47 ` Asus A8V , via vt8251 AHCI Don Carroll
1 sibling, 1 reply; 13+ messages in thread
From: Don Carroll @ 2005-11-02 4:36 UTC (permalink / raw)
To: Randy.Dunlap, linux-ide
[-- Attachment #1: Type: text/plain, Size: 62 bytes --]
I think it was , I can try again
the next one is without MSI
[-- Attachment #2: dmesg-no-msi.txt --]
[-- Type: text/plain, Size: 16028 bytes --]
Bootdata ok (command line is root=/dev/sda1 resume=/dev/sda5)
Linux version 2.6.14 (root@vcr.star-c.com) (gcc version 4.0.1 (4.0.1-5mdk for Mandriva Linux release 2006.0)) #2 SMP Tue Nov 1 21:56:43 CST 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000007ffb0000 (usable)
BIOS-e820: 000000007ffb0000 - 000000007ffbe000 (ACPI data)
BIOS-e820: 000000007ffbe000 - 000000007ffe0000 (ACPI NVS)
BIOS-e820: 000000007ffe0000 - 0000000080000000 (reserved)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000ff7c0000 - 0000000100000000 (reserved)
ACPI: RSDP (v002 ACPIAM ) @ 0x00000000000fac60
ACPI: XSDT (v001 A M I OEMXSDT 0x09000505 MSFT 0x00000097) @ 0x000000007ffb0100
ACPI: FADT (v003 A M I OEMFACP 0x09000505 MSFT 0x00000097) @ 0x000000007ffb0290
ACPI: MADT (v001 A M I OEMAPIC 0x09000505 MSFT 0x00000097) @ 0x000000007ffb0390
ACPI: OEMB (v001 A M I AMI_OEM 0x09000505 MSFT 0x00000097) @ 0x000000007ffbe040
ACPI: DSDT (v001 A0347 A0347001 0x00000001 INTL 0x02002026) @ 0x0000000000000000
Scanning NUMA topology in Northbridge 24
Number of nodes 1
Node 0 MemBase 0000000000000000 Limit 000000007ffb0000
Using 20 for the hash shift. Max adder is 7ffb0000
Using node hash shift of 20
Bootmem setup node 0 0000000000000000-000000007ffb0000
On node 0 totalpages: 524111
DMA zone: 3999 pages, LIFO batch:1
Normal zone: 520112 pages, LIFO batch:31
HighMem zone: 0 pages, LIFO batch:1
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:3 APIC version 16
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1 15:3 APIC version 16
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Setting APIC routing to flat
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 88000000 (gap: 80000000:60000000)
Checking aperture...
CPU 0: aperture @ d8000000 size 128 MB
Built 1 zonelists
Kernel command line: root=/dev/sda1 resume=/dev/sda5
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 131072 bytes)
time.c: Using 3.579545 MHz PM timer.
time.c: Detected 2000.184 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
Memory: 2057440k/2096832k available (2142k kernel code, 39004k reserved, 755k data, 232k init)
Calibrating delay using timer specific routine.. 4007.36 BogoMIPS (lpj=8014724)
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU 0(2) -> Node 0 -> Core 0
mtrr: v2.0 (20020519)
Using local APIC timer interrupts.
Detected 12.501 MHz APIC timer.
softlockup thread 0 started up.
Booting processor 1/2 APIC 0x1
Initializing CPU#1
Calibrating delay using timer specific routine.. 4000.47 BogoMIPS (lpj=8000946)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU 1(2) -> Node 0 -> Core 1
AMD Athlon(tm) 64 X2 Dual Core Processor 3800+ stepping 02
CPU 1: Syncing TSC to CPU 0.
CPU 1: synchronized TSC with CPU 0 (last diff -77 cycles, maxerr 545 cycles)
Brought up 2 CPUs
softlockup thread 1 started up.
Disabling vsyscall due to use of PM timer
time.c: Using PM based timekeeping.
testing NMI watchdog ... OK.
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using configuration type 1
ACPI: Subsystem revision 20050902
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P7._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P7.P7P9._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P7.P7P8._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs *3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
agpgart: Detected AGP bridge 0
agpgart: AGP aperture is 128M @ 0xd8000000
PCI-DMA: Disabling IOMMU.
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: fa900000-fe9fffff
PREFETCH window: aff00000-cfefffff
PCI: Bridge: 0000:02:00.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:02:00.1
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:13.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Setting latency timer of device 0000:00:01.0 to 64
PCI: Setting latency timer of device 0000:00:13.0 to 64
PCI: Setting latency timer of device 0000:02:00.0 to 64
PCI: Setting latency timer of device 0000:02:00.1 to 64
IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $
audit: initializing netlink socket (disabled)
audit(1130905345.620:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
Initializing Cryptographic API
PCI: Setting latency timer of device 0000:02:00.0 to 64
pcie_portdrv_probe->Dev[287c:1106] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[pcie00]
PCI: Setting latency timer of device 0000:02:00.1 to 64
pcie_portdrv_probe->Dev[287d:1106] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[pcie00]
Real Time Clock Driver v1.12
Linux agpgart interface v0.101 (c) Dave Jones
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 32000K size 1024 blocksize
pktcdvd: v0.2.0a 2004-07-14 Jens Axboe (axboe@suse.de) and petero2@telia.com
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:0f.1
PCI: Via IRQ fixup for 0000:00:0f.1, from 255 to 0
VP_IDE: chipset revision 7
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: Unknown VIA SouthBridge, disabling DMA.
VP_IDE: IDE controller at PCI slot 0000:00:0f.1
VP_IDE: chipset revision 7
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: Unknown VIA SouthBridge, disabling DMA.
mice: PS/2 mouse device common for all mice
md: md driver 0.90.2 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 3.39
NET: Registered protocol family 2
input: AT Translated Set 2 keyboard on isa0060/serio0
IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
BIOS EDD facility v0.16 2004-Jun-25, 2 devices found
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
SCSI subsystem initialized
libata version 1.12 loaded.
sata_sil version 0.9
ACPI: PCI Interrupt 0000:00:0c.0[A] -> GSI 17 (level, low) -> IRQ 16
ata1: SATA max UDMA/100 cmd 0xFFFFC20000004C80 ctl 0xFFFFC20000004C8A bmdma 0xFFFFC20000004C00 irq 16
ata2: SATA max UDMA/100 cmd 0xFFFFC20000004CC0 ctl 0xFFFFC20000004CCA bmdma 0xFFFFC20000004C08 irq 16
input: ImPS/2 Generic Wheel Mouse on isa0060/serio1
ata1: no device found (phy stat 00000000)
scsi0 : sata_sil
ata2: dev 0 cfg 49:2f00 82:74eb 83:7fea 84:4023 85:74e9 86:3c02 87:4023 88:203f
ata2: dev 0 ATA, max UDMA/100, 488397168 sectors: lba48
ata2: dev 0 configured for UDMA/100
scsi1 : sata_sil
Vendor: ATA Model: HDS722525VLSA80 Rev: V36O
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
SCSI device sda: drive cache: write back
sda: sda1 sda2 < sda5 sda6 sda7 >
Attached scsi disk sda at scsi1, channel 0, id 0, lun 0
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 232k freed
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.3
ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 20 (level, low) -> IRQ 17
PCI: Via IRQ fixup for 0000:00:10.0, from 11 to 1
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:10.0: irq 17, io base 0x0000d480
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.1[C] -> GSI 22 (level, low) -> IRQ 18
PCI: Via IRQ fixup for 0000:00:10.1, from 5 to 2
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.1: irq 18, io base 0x0000d400
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 19
PCI: Via IRQ fixup for 0000:00:10.2, from 10 to 3
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.2: irq 19, io base 0x0000d080
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.3[D] -> GSI 23 (level, low) -> IRQ 20
PCI: Via IRQ fixup for 0000:00:10.3, from 3 to 4
uhci_hcd 0000:00:10.3: UHCI Host Controller
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.3: irq 20, io base 0x0000d000
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.4[C] -> GSI 22 (level, low) -> IRQ 18
PCI: Via IRQ fixup for 0000:00:10.4, from 5 to 2
ehci_hcd 0000:00:10.4: EHCI Host Controller
ehci_hcd 0000:00:10.4: debug port 1
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:10.4: irq 18, io mem 0xfebdf400
ehci_hcd 0000:00:10.4: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
ts: Compaq touchscreen protocol output
ACPI: Power Button (FF) [PWRF]
ACPI: Sleep Button (CM) [SLPB]
ACPI: Power Button (CM) [PWRB]
ibm_acpi: ec object not found
ACPI: CPU0 (power states: C1[C1])
ACPI: Processor [CPU1] (supports 16 throttling states)
ACPI: CPU1 (power states: C1[C1])
EXT3 FS on sda1, internal journal
Adding 2939852k swap on /dev/sda5. Priority:-1 extents:1 across:2939852k
Linux video capture interface: v1.00
bttv: driver version 0.9.16 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
Probing IDE interface ide0...
Probing IDE interface ide1...
hdc: TDK DVDRW0404N, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
ahci version 1.01
ACPI: PCI Interrupt 0000:00:0f.0[B] -> GSI 21 (level, low) -> IRQ 19
PCI: Via IRQ fixup for 0000:00:0f.0, from 10 to 3
ahci(0000:00:0f.0) AHCI 0001.0000 32 slots 4 ports 3 Gbps 0xf impl SATA mode
ahci(0000:00:0f.0) flags: 64bit ncq pm led clo pmp pio slum part
ata3: SATA max UDMA/133 cmd 0xFFFFC20000020D00 ctl 0x0 bmdma 0x0 irq 19
ata4: SATA max UDMA/133 cmd 0xFFFFC20000020D80 ctl 0x0 bmdma 0x0 irq 19
ata5: SATA max UDMA/133 cmd 0xFFFFC20000020E00 ctl 0x0 bmdma 0x0 irq 19
ata6: SATA max UDMA/133 cmd 0xFFFFC20000020E80 ctl 0x0 bmdma 0x0 irq 19
ata3: no device found (phy stat 00000000)
scsi2 : ahci
ata4: no device found (phy stat 00000000)
scsi3 : ahci
ata5: no device found (phy stat 00000000)
scsi4 : ahci
ata6 is slow to respond, please be patient
ata6 failed to respond (30 secs)
scsi5 : ahci
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
loop: loaded (max 8 devices)
hdc: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache
Uniform CD-ROM driver Revision: 3.20
floppy0: no floppy controllers found
floppy0: no floppy controllers found
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
NET: Registered protocol family 17
via-rhine.c:v1.10-LK1.2.0-2.6 June-10-2004 Written by Donald Becker
ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 23 (level, low) -> IRQ 20
PCI: Via IRQ fixup for 0000:00:12.0, from 11 to 4
eth0: VIA Rhine II at 0x1c400, 00:13:d4:a7:d6:43, IRQ 20.
eth0: MII PHY found at address 1, status 0x786d advertising 01e1 Link 40a1.
eth0: link up, 100Mbps, half-duplex, lpa 0x40A1
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP]
parport0: irq 7 detected
parport0: Printer, Hewlett-Packard HP LaserJet 6L
lp0: using parport0 (polling).
lp0: console ready
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
via82xx: Assuming DXS channels with 48k fixed sample rate.
Please try dxs_support=5 option
and report if it works on your machine.
For more details, read ALSA-Configuration.txt.
ACPI: PCI Interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 18
PCI: Via IRQ fixup for 0000:00:11.5, from 5 to 2
PCI: Setting latency timer of device 0000:00:11.5 to 64
cdrom: This disc doesn't have any tracks I recognize!
NET: Registered protocol family 10
Disabled Privacy Extensions on device ffffffff80393380(lo)
IPv6 over IPv4 tunneling driver
eth0: no IPv6 routers present
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
NFSD: recovery directory /var/lib/nfs/v4recovery doesn't exist
NFSD: starting 90-second grace period
powernow-k8: Found 2 AMD Athlon 64 / Opteron processors (version 1.50.4)
powernow-k8: 0 : fid 0xc (2000 MHz), vid 0x8 (1350 mV)
powernow-k8: 1 : fid 0xa (1800 MHz), vid 0xa (1300 mV)
powernow-k8: 2 : fid 0x2 (1000 MHz), vid 0x12 (1100 mV)
cpu_init done, current fid 0xc, vid 0x8
floppy0: no floppy controllers found
floppy0: no floppy controllers found
kdm[3134]: segfault at 0000000000000000 rip 000000000040a90b rsp 00007fffffa9c800 error 4
floppy0: no floppy controllers found
floppy0: no floppy controllers found
floppy0: no floppy controllers found
floppy0: no floppy controllers found
Attached scsi generic sg0 at scsi1, channel 0, id 0, lun 0, type 0
kdm[4438]: segfault at 0000000000000000 rip 000000000040a90b rsp 00007fffff8671a0 error 4
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: Asus A8V , via vt8251 AHCI
2005-11-02 3:57 ` Randy.Dunlap
2005-11-02 4:36 ` Don Carroll
@ 2005-11-02 4:47 ` Don Carroll
1 sibling, 0 replies; 13+ messages in thread
From: Don Carroll @ 2005-11-02 4:47 UTC (permalink / raw)
To: Randy.Dunlap, linux-ide
[-- Attachment #1: Type: text/plain, Size: 157 bytes --]
> This boot log isn't the one where you tried irqpoll, right?
you are correct , this one is , also with no MSI , now will go build kernel
with MSI back on
[-- Attachment #2: dmesg-no-msi-and-irq-poll.txt --]
[-- Type: text/plain, Size: 15538 bytes --]
Bootdata ok (command line is root=/dev/sda1 resume=/dev/sda5 irqpoll)
Linux version 2.6.14 (root@vcr.star-c.com) (gcc version 4.0.1 (4.0.1-5mdk for Mandriva Linux release 2006.0)) #2 SMP Tue Nov 1 21:56:43 CST 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000007ffb0000 (usable)
BIOS-e820: 000000007ffb0000 - 000000007ffbe000 (ACPI data)
BIOS-e820: 000000007ffbe000 - 000000007ffe0000 (ACPI NVS)
BIOS-e820: 000000007ffe0000 - 0000000080000000 (reserved)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000ff7c0000 - 0000000100000000 (reserved)
ACPI: RSDP (v002 ACPIAM ) @ 0x00000000000fac60
ACPI: XSDT (v001 A M I OEMXSDT 0x09000505 MSFT 0x00000097) @ 0x000000007ffb0100
ACPI: FADT (v003 A M I OEMFACP 0x09000505 MSFT 0x00000097) @ 0x000000007ffb0290
ACPI: MADT (v001 A M I OEMAPIC 0x09000505 MSFT 0x00000097) @ 0x000000007ffb0390
ACPI: OEMB (v001 A M I AMI_OEM 0x09000505 MSFT 0x00000097) @ 0x000000007ffbe040
ACPI: DSDT (v001 A0347 A0347001 0x00000001 INTL 0x02002026) @ 0x0000000000000000
Scanning NUMA topology in Northbridge 24
Number of nodes 1
Node 0 MemBase 0000000000000000 Limit 000000007ffb0000
Using 20 for the hash shift. Max adder is 7ffb0000
Using node hash shift of 20
Bootmem setup node 0 0000000000000000-000000007ffb0000
On node 0 totalpages: 524111
DMA zone: 3999 pages, LIFO batch:1
Normal zone: 520112 pages, LIFO batch:31
HighMem zone: 0 pages, LIFO batch:1
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:3 APIC version 16
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1 15:3 APIC version 16
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Setting APIC routing to flat
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 88000000 (gap: 80000000:60000000)
Checking aperture...
CPU 0: aperture @ dc000000 size 64 MB
Built 1 zonelists
Kernel command line: root=/dev/sda1 resume=/dev/sda5 irqpoll
Misrouted IRQ fixup and polling support enabled
This may significantly impact system performance
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 131072 bytes)
time.c: Using 3.579545 MHz PM timer.
time.c: Detected 2000.184 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
Memory: 2057440k/2096832k available (2142k kernel code, 39004k reserved, 755k data, 232k init)
Calibrating delay using timer specific routine.. 4011.50 BogoMIPS (lpj=8023008)
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU 0(2) -> Node 0 -> Core 0
mtrr: v2.0 (20020519)
Using local APIC timer interrupts.
Detected 12.501 MHz APIC timer.
softlockup thread 0 started up.
Booting processor 1/2 APIC 0x1
Initializing CPU#1
Calibrating delay using timer specific routine.. 4000.34 BogoMIPS (lpj=8000690)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU 1(2) -> Node 0 -> Core 1
AMD Athlon(tm) 64 X2 Dual Core Processor 3800+ stepping 02
CPU 1: Syncing TSC to CPU 0.
CPU 1: synchronized TSC with CPU 0 (last diff -77 cycles, maxerr 545 cycles)
Brought up 2 CPUs
softlockup thread 1 started up.
Disabling vsyscall due to use of PM timer
time.c: Using PM based timekeeping.
testing NMI watchdog ... OK.
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using configuration type 1
ACPI: Subsystem revision 20050902
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P7._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P7.P7P9._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P7.P7P8._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs *3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
agpgart: Detected AGP bridge 0
agpgart: AGP aperture is 64M @ 0xdc000000
PCI-DMA: Disabling IOMMU.
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: fa900000-fe9fffff
PREFETCH window: b7f00000-d7efffff
PCI: Bridge: 0000:02:00.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:02:00.1
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:13.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Setting latency timer of device 0000:00:01.0 to 64
PCI: Setting latency timer of device 0000:00:13.0 to 64
PCI: Setting latency timer of device 0000:02:00.0 to 64
PCI: Setting latency timer of device 0000:02:00.1 to 64
IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $
audit: initializing netlink socket (disabled)
audit(1130906505.388:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
Initializing Cryptographic API
PCI: Setting latency timer of device 0000:02:00.0 to 64
pcie_portdrv_probe->Dev[287c:1106] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[pcie00]
PCI: Setting latency timer of device 0000:02:00.1 to 64
pcie_portdrv_probe->Dev[287d:1106] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[pcie00]
Real Time Clock Driver v1.12
Linux agpgart interface v0.101 (c) Dave Jones
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 32000K size 1024 blocksize
pktcdvd: v0.2.0a 2004-07-14 Jens Axboe (axboe@suse.de) and petero2@telia.com
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:0f.1
PCI: Via IRQ fixup for 0000:00:0f.1, from 255 to 0
VP_IDE: chipset revision 7
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: Unknown VIA SouthBridge, disabling DMA.
VP_IDE: IDE controller at PCI slot 0000:00:0f.1
VP_IDE: chipset revision 7
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: Unknown VIA SouthBridge, disabling DMA.
mice: PS/2 mouse device common for all mice
md: md driver 0.90.2 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 3.39
NET: Registered protocol family 2
input: AT Translated Set 2 keyboard on isa0060/serio0
IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
BIOS EDD facility v0.16 2004-Jun-25, 2 devices found
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
SCSI subsystem initialized
libata version 1.12 loaded.
sata_sil version 0.9
ACPI: PCI Interrupt 0000:00:0c.0[A] -> GSI 17 (level, low) -> IRQ 16
ata1: SATA max UDMA/100 cmd 0xFFFFC20000004C80 ctl 0xFFFFC20000004C8A bmdma 0xFFFFC20000004C00 irq 16
ata2: SATA max UDMA/100 cmd 0xFFFFC20000004CC0 ctl 0xFFFFC20000004CCA bmdma 0xFFFFC20000004C08 irq 16
input: ImPS/2 Generic Wheel Mouse on isa0060/serio1
ata1: no device found (phy stat 00000000)
scsi0 : sata_sil
ata2: dev 0 cfg 49:2f00 82:74eb 83:7fea 84:4023 85:74e9 86:3c02 87:4023 88:203f
ata2: dev 0 ATA, max UDMA/100, 488397168 sectors: lba48
ata2: dev 0 configured for UDMA/100
scsi1 : sata_sil
Vendor: ATA Model: HDS722525VLSA80 Rev: V36O
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
SCSI device sda: drive cache: write back
sda: sda1 sda2 < sda5 sda6 sda7 >
Attached scsi disk sda at scsi1, channel 0, id 0, lun 0
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 232k freed
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.3
ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 20 (level, low) -> IRQ 17
PCI: Via IRQ fixup for 0000:00:10.0, from 11 to 1
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:10.0: irq 17, io base 0x0000d480
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.1[C] -> GSI 22 (level, low) -> IRQ 18
PCI: Via IRQ fixup for 0000:00:10.1, from 5 to 2
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.1: irq 18, io base 0x0000d400
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 19
PCI: Via IRQ fixup for 0000:00:10.2, from 10 to 3
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.2: irq 19, io base 0x0000d080
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.3[D] -> GSI 23 (level, low) -> IRQ 20
PCI: Via IRQ fixup for 0000:00:10.3, from 3 to 4
uhci_hcd 0000:00:10.3: UHCI Host Controller
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.3: irq 20, io base 0x0000d000
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.4[C] -> GSI 22 (level, low) -> IRQ 18
PCI: Via IRQ fixup for 0000:00:10.4, from 5 to 2
ehci_hcd 0000:00:10.4: EHCI Host Controller
ehci_hcd 0000:00:10.4: debug port 1
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:10.4: irq 18, io mem 0xfebdf400
ehci_hcd 0000:00:10.4: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
ts: Compaq touchscreen protocol output
ACPI: Power Button (FF) [PWRF]
ACPI: Sleep Button (CM) [SLPB]
ACPI: Power Button (CM) [PWRB]
ibm_acpi: ec object not found
ACPI: CPU0 (power states: C1[C1])
ACPI: Processor [CPU1] (supports 16 throttling states)
ACPI: CPU1 (power states: C1[C1])
EXT3 FS on sda1, internal journal
Adding 2939852k swap on /dev/sda5. Priority:-1 extents:1 across:2939852k
Linux video capture interface: v1.00
bttv: driver version 0.9.16 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
Probing IDE interface ide0...
Probing IDE interface ide1...
hdc: TDK DVDRW0404N, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
ahci version 1.01
ACPI: PCI Interrupt 0000:00:0f.0[B] -> GSI 21 (level, low) -> IRQ 19
PCI: Via IRQ fixup for 0000:00:0f.0, from 10 to 3
ahci(0000:00:0f.0) AHCI 0001.0000 32 slots 4 ports 3 Gbps 0xf impl SATA mode
ahci(0000:00:0f.0) flags: 64bit ncq pm led clo pmp pio slum part
ata3: SATA max UDMA/133 cmd 0xFFFFC20000020D00 ctl 0x0 bmdma 0x0 irq 19
ata4: SATA max UDMA/133 cmd 0xFFFFC20000020D80 ctl 0x0 bmdma 0x0 irq 19
ata5: SATA max UDMA/133 cmd 0xFFFFC20000020E00 ctl 0x0 bmdma 0x0 irq 19
ata6: SATA max UDMA/133 cmd 0xFFFFC20000020E80 ctl 0x0 bmdma 0x0 irq 19
ata3: no device found (phy stat 00000000)
scsi2 : ahci
ata4: no device found (phy stat 00000000)
scsi3 : ahci
ata5: no device found (phy stat 00000000)
scsi4 : ahci
ata6 is slow to respond, please be patient
ata6 failed to respond (30 secs)
scsi5 : ahci
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
loop: loaded (max 8 devices)
hdc: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache
Uniform CD-ROM driver Revision: 3.20
floppy0: no floppy controllers found
floppy0: no floppy controllers found
NET: Registered protocol family 17
via-rhine.c:v1.10-LK1.2.0-2.6 June-10-2004 Written by Donald Becker
ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 23 (level, low) -> IRQ 20
PCI: Via IRQ fixup for 0000:00:12.0, from 11 to 4
eth0: VIA Rhine II at 0x1c400, 00:13:d4:a7:d6:43, IRQ 20.
eth0: MII PHY found at address 1, status 0x786d advertising 01e1 Link 40a1.
eth0: link up, 100Mbps, half-duplex, lpa 0x40A1
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP]
parport0: irq 7 detected
parport0: Printer, Hewlett-Packard HP LaserJet 6L
lp0: using parport0 (polling).
lp0: console ready
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
via82xx: Assuming DXS channels with 48k fixed sample rate.
Please try dxs_support=5 option
and report if it works on your machine.
For more details, read ALSA-Configuration.txt.
ACPI: PCI Interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 18
PCI: Via IRQ fixup for 0000:00:11.5, from 5 to 2
PCI: Setting latency timer of device 0000:00:11.5 to 64
cdrom: This disc doesn't have any tracks I recognize!
NET: Registered protocol family 10
Disabled Privacy Extensions on device ffffffff80393380(lo)
IPv6 over IPv4 tunneling driver
eth0: no IPv6 routers present
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
NFSD: recovery directory /var/lib/nfs/v4recovery doesn't exist
NFSD: starting 90-second grace period
powernow-k8: Found 2 AMD Athlon 64 / Opteron processors (version 1.50.4)
powernow-k8: 0 : fid 0xc (2000 MHz), vid 0x8 (1350 mV)
powernow-k8: 1 : fid 0xa (1800 MHz), vid 0xa (1300 mV)
powernow-k8: 2 : fid 0x2 (1000 MHz), vid 0x12 (1100 mV)
cpu_init done, current fid 0xc, vid 0x8
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: Asus A8V , via vt8251 AHCI
2005-11-02 4:36 ` Don Carroll
@ 2005-11-02 4:56 ` Randy.Dunlap
2005-11-02 5:13 ` Don Carroll
0 siblings, 1 reply; 13+ messages in thread
From: Randy.Dunlap @ 2005-11-02 4:56 UTC (permalink / raw)
Cc: ibedonc, linux-ide
On Tue, 1 Nov 2005 22:36:43 -0600 Don Carroll wrote:
> I think it was , I can try again
>
> the next one is without MSI
>
I'm sorry to put you to all of that trouble.
I've seen some very similar issues which turned out to be MSI-related,
but this one doesn't seem to be that way -- unless MSI + irqpoll
(your next test) happens to work for you -- then manybe it will
give us some more evidence. If it does boot, please send us
the contents of /proc/interrupts .
---
~Randy
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: Asus A8V , via vt8251 AHCI
2005-11-02 5:13 ` Don Carroll
@ 2005-11-02 5:12 ` Randy.Dunlap
2005-11-02 5:22 ` Don Carroll
2005-11-04 2:36 ` Asus A8V , via vt8251 AHCI time Don Carroll
0 siblings, 2 replies; 13+ messages in thread
From: Randy.Dunlap @ 2005-11-02 5:12 UTC (permalink / raw)
Cc: ibedonc, linux-ide
On Tue, 1 Nov 2005 23:13:43 -0600 Don Carroll wrote:
> On Tue, Nov 01, 2005 at 08:56:59PM -0800, Randy.Dunlap wrote:
> > On Tue, 1 Nov 2005 22:36:43 -0600 Don Carroll wrote:
> >
> > > I think it was , I can try again
> > >
> > > the next one is without MSI
> > >
> >
> > I'm sorry to put you to all of that trouble.
> Hey I want to get it working :)
> was no trouble (I am systems Eng)
OK, good.
> > I've seen some very similar issues which turned out to be MSI-related,
> > but this one doesn't seem to be that way -- unless MSI + irqpoll
> > (your next test) happens to work for you -- then manybe it will
> > give us some more evidence. If it does boot, please send us
> > the contents of /proc/interrupts .
> nope , still times out
>
> here is /proc/interrupts anyway
> irq 19 is the ahci
and irq 16 also (libata on both of them).
How do you know which one is for which controller/drive(s)?
Anyone else out there have ideas??
> CPU0 CPU1
> 0: 333 459694 IO-APIC-edge timer
> 1: 3 4244 IO-APIC-edge i8042
> 8: 0 0 IO-APIC-edge rtc
> 9: 0 0 IO-APIC-level acpi
> 12: 31 51463 IO-APIC-edge i8042
> 15: 5 14079 IO-APIC-edge ide1
> 16: 26 72751 IO-APIC-level libata
> 17: 0 0 IO-APIC-level uhci_hcd:usb1
> 18: 0 77 IO-APIC-level uhci_hcd:usb2, ehci_hcd:usb5,
> VIA8237
> 19: 0 0 IO-APIC-level uhci_hcd:usb3, libata
> 20: 2 2824 IO-APIC-level uhci_hcd:usb4, eth0
> NMI: 641 1026
> LOC: 459992 459969
> ERR: 0
> MIS: 0
---
~Randy
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: Asus A8V , via vt8251 AHCI
2005-11-02 4:56 ` Randy.Dunlap
@ 2005-11-02 5:13 ` Don Carroll
2005-11-02 5:12 ` Randy.Dunlap
0 siblings, 1 reply; 13+ messages in thread
From: Don Carroll @ 2005-11-02 5:13 UTC (permalink / raw)
To: Randy.Dunlap, linux-ide
On Tue, Nov 01, 2005 at 08:56:59PM -0800, Randy.Dunlap wrote:
> On Tue, 1 Nov 2005 22:36:43 -0600 Don Carroll wrote:
>
> > I think it was , I can try again
> >
> > the next one is without MSI
> >
>
> I'm sorry to put you to all of that trouble.
Hey I want to get it working :)
was no trouble (I am systems Eng)
>
> I've seen some very similar issues which turned out to be MSI-related,
> but this one doesn't seem to be that way -- unless MSI + irqpoll
> (your next test) happens to work for you -- then manybe it will
> give us some more evidence. If it does boot, please send us
> the contents of /proc/interrupts .
nope , still times out
here is /proc/interrupts anyway
irq 19 is the ahci
CPU0 CPU1
0: 333 459694 IO-APIC-edge timer
1: 3 4244 IO-APIC-edge i8042
8: 0 0 IO-APIC-edge rtc
9: 0 0 IO-APIC-level acpi
12: 31 51463 IO-APIC-edge i8042
15: 5 14079 IO-APIC-edge ide1
16: 26 72751 IO-APIC-level libata
17: 0 0 IO-APIC-level uhci_hcd:usb1
18: 0 77 IO-APIC-level uhci_hcd:usb2, ehci_hcd:usb5,
VIA8237
19: 0 0 IO-APIC-level uhci_hcd:usb3, libata
20: 2 2824 IO-APIC-level uhci_hcd:usb4, eth0
NMI: 641 1026
LOC: 459992 459969
ERR: 0
MIS: 0
>
> ---
> ~Randy
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: Asus A8V , via vt8251 AHCI
2005-11-02 5:12 ` Randy.Dunlap
@ 2005-11-02 5:22 ` Don Carroll
2005-11-04 2:36 ` Asus A8V , via vt8251 AHCI time Don Carroll
1 sibling, 0 replies; 13+ messages in thread
From: Don Carroll @ 2005-11-02 5:22 UTC (permalink / raw)
To: Randy.Dunlap, linux-ide
On Tue, Nov 01, 2005 at 09:12:03PM -0800, Randy.Dunlap wrote:
> On Tue, 1 Nov 2005 23:13:43 -0600 Don Carroll wrote:
>
> > On Tue, Nov 01, 2005 at 08:56:59PM -0800, Randy.Dunlap wrote:
> > > On Tue, 1 Nov 2005 22:36:43 -0600 Don Carroll wrote:
> > >
> > > > I think it was , I can try again
> > > >
> > > > the next one is without MSI
> > > >
> > >
> > > I'm sorry to put you to all of that trouble.
> > Hey I want to get it working :)
> > was no trouble (I am systems Eng)
>
> OK, good.
>
> > > I've seen some very similar issues which turned out to be MSI-related,
> > > but this one doesn't seem to be that way -- unless MSI + irqpoll
> > > (your next test) happens to work for you -- then manybe it will
> > > give us some more evidence. If it does boot, please send us
> > > the contents of /proc/interrupts .
> > nope , still times out
> >
> > here is /proc/interrupts anyway
> > irq 19 is the ahci
>
> and irq 16 also (libata on both of them).
when I rmmod ahci it, libata drops from 19
> How do you know which one is for which controller/drive(s)?
>
> Anyone else out there have ideas??
>
>
> > CPU0 CPU1
> > 0: 333 459694 IO-APIC-edge timer
> > 1: 3 4244 IO-APIC-edge i8042
> > 8: 0 0 IO-APIC-edge rtc
> > 9: 0 0 IO-APIC-level acpi
> > 12: 31 51463 IO-APIC-edge i8042
> > 15: 5 14079 IO-APIC-edge ide1
> > 16: 26 72751 IO-APIC-level libata
> > 17: 0 0 IO-APIC-level uhci_hcd:usb1
> > 18: 0 77 IO-APIC-level uhci_hcd:usb2, ehci_hcd:usb5,
> > VIA8237
> > 19: 0 0 IO-APIC-level uhci_hcd:usb3, libata
> > 20: 2 2824 IO-APIC-level uhci_hcd:usb4, eth0
> > NMI: 641 1026
> > LOC: 459992 459969
> > ERR: 0
> > MIS: 0
>
>
> ---
> ~Randy
^ permalink raw reply [flat|nested] 13+ messages in thread
* Asus A8V , via vt8251 AHCI time
2005-11-02 5:12 ` Randy.Dunlap
2005-11-02 5:22 ` Don Carroll
@ 2005-11-04 2:36 ` Don Carroll
1 sibling, 0 replies; 13+ messages in thread
From: Don Carroll @ 2005-11-04 2:36 UTC (permalink / raw)
To: linux-ide
anyone alse got any ideas
on this
Jeff Garzik ??
On Tue, Nov 01, 2005 at 09:12:03PM -0800, Randy.Dunlap wrote:
> On Tue, 1 Nov 2005 23:13:43 -0600 Don Carroll wrote:
>
> > On Tue, Nov 01, 2005 at 08:56:59PM -0800, Randy.Dunlap wrote:
> > > On Tue, 1 Nov 2005 22:36:43 -0600 Don Carroll wrote:
> > >
> > > > I think it was , I can try again
> > > >
> > > > the next one is without MSI
> > > >
> > >
> > > I'm sorry to put you to all of that trouble.
> > Hey I want to get it working :)
> > was no trouble (I am systems Eng)
>
> OK, good.
>
> > > I've seen some very similar issues which turned out to be MSI-related,
> > > but this one doesn't seem to be that way -- unless MSI + irqpoll
> > > (your next test) happens to work for you -- then manybe it will
> > > give us some more evidence. If it does boot, please send us
> > > the contents of /proc/interrupts .
> > nope , still times out
> >
> > here is /proc/interrupts anyway
> > irq 19 is the ahci
>
> and irq 16 also (libata on both of them).
> How do you know which one is for which controller/drive(s)?
>
> Anyone else out there have ideas??
>
>
> > CPU0 CPU1
> > 0: 333 459694 IO-APIC-edge timer
> > 1: 3 4244 IO-APIC-edge i8042
> > 8: 0 0 IO-APIC-edge rtc
> > 9: 0 0 IO-APIC-level acpi
> > 12: 31 51463 IO-APIC-edge i8042
> > 15: 5 14079 IO-APIC-edge ide1
> > 16: 26 72751 IO-APIC-level libata
> > 17: 0 0 IO-APIC-level uhci_hcd:usb1
> > 18: 0 77 IO-APIC-level uhci_hcd:usb2, ehci_hcd:usb5,
> > VIA8237
> > 19: 0 0 IO-APIC-level uhci_hcd:usb3, libata
> > 20: 2 2824 IO-APIC-level uhci_hcd:usb4, eth0
> > NMI: 641 1026
> > LOC: 459992 459969
> > ERR: 0
> > MIS: 0
>
>
> ---
> ~Randy
^ permalink raw reply [flat|nested] 13+ messages in thread
end of thread, other threads:[~2005-11-04 2:37 UTC | newest]
Thread overview: 13+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2005-11-01 6:40 Asus A8V , via vt8251 AHCI Don Carroll
2005-11-01 15:40 ` Randy.Dunlap
[not found] ` <20051101192449.GA9719@vcr.star-c.com>
2005-11-01 20:42 ` Randy.Dunlap
2005-11-02 0:39 ` Don Carroll
2005-11-02 3:41 ` Don Carroll
2005-11-02 3:57 ` Randy.Dunlap
2005-11-02 4:36 ` Don Carroll
2005-11-02 4:56 ` Randy.Dunlap
2005-11-02 5:13 ` Don Carroll
2005-11-02 5:12 ` Randy.Dunlap
2005-11-02 5:22 ` Don Carroll
2005-11-04 2:36 ` Asus A8V , via vt8251 AHCI time Don Carroll
2005-11-02 4:47 ` Asus A8V , via vt8251 AHCI Don Carroll
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.