From: Auke Kok <auke-jan.h.kok@intel.com>
To: jeff@garzik.org
Cc: netdev@vger.kernel.org, jesse.brandeburg@intel.com,
john.ronciak@intel.com
Subject: [PATCH 1/4] e1000e: alternate MAC address support
Date: Wed, 31 Oct 2007 15:21:52 -0700 [thread overview]
Message-ID: <20071031222152.17411.20977.stgit@localhost.localdomain> (raw)
From: Bill Hayes <bill.hayes@hp.com>
Port alternate MAC address support from the sourceforge
e1000 driver to the upstream e1000e driver.
Signed-off-by: Bill Hayes <bill.hayes@hp.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
---
drivers/net/e1000e/82571.c | 4 ++++
drivers/net/e1000e/defines.h | 1 +
drivers/net/e1000e/hw.h | 1 +
drivers/net/e1000e/lib.c | 39 +++++++++++++++++++++++++++++++++++++--
4 files changed, 43 insertions(+), 2 deletions(-)
diff --git a/drivers/net/e1000e/82571.c b/drivers/net/e1000e/82571.c
index 14141a5..b6401ab 100644
--- a/drivers/net/e1000e/82571.c
+++ b/drivers/net/e1000e/82571.c
@@ -752,6 +752,10 @@ static s32 e1000_reset_hw_82571(struct e1000_hw *hw)
ew32(IMC, 0xffffffff);
icr = er32(ICR);
+ if (hw->mac.type == e1000_82571 &&
+ hw->dev_spec.e82571.alt_mac_addr_is_present)
+ e1000e_set_laa_state_82571(hw, true);
+
return 0;
}
diff --git a/drivers/net/e1000e/defines.h b/drivers/net/e1000e/defines.h
index b32ed45..f2175ea 100644
--- a/drivers/net/e1000e/defines.h
+++ b/drivers/net/e1000e/defines.h
@@ -557,6 +557,7 @@
#define NVM_INIT_3GIO_3 0x001A
#define NVM_INIT_CONTROL3_PORT_A 0x0024
#define NVM_CFG 0x0012
+#define NVM_ALT_MAC_ADDR_PTR 0x0037
#define NVM_CHECKSUM_REG 0x003F
#define E1000_NVM_CFG_DONE_PORT_0 0x40000 /* MNG config cycle done */
diff --git a/drivers/net/e1000e/hw.h b/drivers/net/e1000e/hw.h
index 6451578..1bb2052 100644
--- a/drivers/net/e1000e/hw.h
+++ b/drivers/net/e1000e/hw.h
@@ -816,6 +816,7 @@ struct e1000_bus_info {
struct e1000_dev_spec_82571 {
bool laa_is_present;
+ bool alt_mac_addr_is_present;
};
struct e1000_shadow_ram {
diff --git a/drivers/net/e1000e/lib.c b/drivers/net/e1000e/lib.c
index 0bdeca3..16f35fa 100644
--- a/drivers/net/e1000e/lib.c
+++ b/drivers/net/e1000e/lib.c
@@ -2059,9 +2059,44 @@ s32 e1000e_read_mac_addr(struct e1000_hw *hw)
{
s32 ret_val;
u16 offset, nvm_data, i;
+ u16 mac_addr_offset = 0;
+
+ if (hw->mac.type == e1000_82571) {
+ /* Check for an alternate MAC address. An alternate MAC
+ * address can be setup by pre-boot software and must be
+ * treated like a permanent address and must override the
+ * actual permanent MAC address. */
+ ret_val = e1000_read_nvm(hw, NVM_ALT_MAC_ADDR_PTR, 1,
+ &mac_addr_offset);
+ if (ret_val) {
+ hw_dbg(hw, "NVM Read Error\n");
+ return ret_val;
+ }
+ if (mac_addr_offset == 0xFFFF)
+ mac_addr_offset = 0;
+
+ if (mac_addr_offset) {
+ if (hw->bus.func == E1000_FUNC_1)
+ mac_addr_offset += ETH_ALEN/sizeof(u16);
+
+ /* make sure we have a valid mac address here
+ * before using it */
+ ret_val = e1000_read_nvm(hw, mac_addr_offset, 1,
+ &nvm_data);
+ if (ret_val) {
+ hw_dbg(hw, "NVM Read Error\n");
+ return ret_val;
+ }
+ if (nvm_data & 0x0001)
+ mac_addr_offset = 0;
+ }
+
+ if (mac_addr_offset)
+ hw->dev_spec.e82571.alt_mac_addr_is_present = 1;
+ }
for (i = 0; i < ETH_ALEN; i += 2) {
- offset = i >> 1;
+ offset = mac_addr_offset + (i >> 1);
ret_val = e1000_read_nvm(hw, offset, 1, &nvm_data);
if (ret_val) {
hw_dbg(hw, "NVM Read Error\n");
@@ -2072,7 +2107,7 @@ s32 e1000e_read_mac_addr(struct e1000_hw *hw)
}
/* Flip last bit of mac address if we're on second port */
- if (hw->bus.func == E1000_FUNC_1)
+ if (!mac_addr_offset && hw->bus.func == E1000_FUNC_1)
hw->mac.perm_addr[5] ^= 1;
for (i = 0; i < ETH_ALEN; i++)
next reply other threads:[~2007-10-31 22:25 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2007-10-31 22:21 Auke Kok [this message]
2007-10-31 22:22 ` [PATCH 2/4] e1000e: Disable L1 ASPM power savings for 82573 mobile variants Auke Kok
2007-10-31 22:22 ` [PATCH 3/4] e1000/e1000e: Move PCI-Express device IDs over to e1000e Auke Kok
2007-10-31 22:22 ` [PATCH 4/4] ixgbe: Fix copper PHY initialization code Auke Kok
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20071031222152.17411.20977.stgit@localhost.localdomain \
--to=auke-jan.h.kok@intel.com \
--cc=jeff@garzik.org \
--cc=jesse.brandeburg@intel.com \
--cc=john.ronciak@intel.com \
--cc=netdev@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.