From: Auke Kok <auke-jan.h.kok@intel.com>
To: jeff@garzik.org
Cc: netdev@vger.kernel.org, jesse.brandeburg@intel.com,
john.ronciak@intel.com
Subject: [PATCH 2/4] e1000e: Disable L1 ASPM power savings for 82573 mobile variants
Date: Wed, 31 Oct 2007 15:22:00 -0700 [thread overview]
Message-ID: <20071031222200.17411.52942.stgit@localhost.localdomain> (raw)
In-Reply-To: <20071031222152.17411.20977.stgit@localhost.localdomain>
L1 ASPM link (pci-e link power savings) has significant benefits
(~1W savings when link is active) but unfortunately does not work
correctly on any of the chipsets that have 82573 on mobile platforms
which causes various nuisances:
- eeprom reads return garbage information leading to bad eeprom
checksums
- long ping times (up to 2 seconds)
- complete system hangs (freeze/lockup)
A lot of T60 owners have been plagued by this, but other mobile
solutions also suffer from these symptoms.
Disabling L1 ASPM before we activate the PCI-E link fixes all of
these issues at the cost of some power consumption.
Remove a workaround RDTR adjustment that is no longer needed with
this new one.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
---
drivers/net/e1000e/82571.c | 1 -
drivers/net/e1000e/e1000.h | 1 -
drivers/net/e1000e/netdev.c | 30 ++++++++++++++++++++++++++++++
drivers/net/e1000e/param.c | 7 -------
4 files changed, 30 insertions(+), 9 deletions(-)
diff --git a/drivers/net/e1000e/82571.c b/drivers/net/e1000e/82571.c
index b6401ab..45f5ee2 100644
--- a/drivers/net/e1000e/82571.c
+++ b/drivers/net/e1000e/82571.c
@@ -1343,7 +1343,6 @@ struct e1000_info e1000_82573_info = {
| FLAG_HAS_STATS_ICR_ICT
| FLAG_HAS_SMART_POWER_DOWN
| FLAG_HAS_AMT
- | FLAG_HAS_ASPM
| FLAG_HAS_ERT
| FLAG_HAS_SWSM_ON_LOAD,
.pba = 20,
diff --git a/drivers/net/e1000e/e1000.h b/drivers/net/e1000e/e1000.h
index 473f78d..8b88c22 100644
--- a/drivers/net/e1000e/e1000.h
+++ b/drivers/net/e1000e/e1000.h
@@ -288,7 +288,6 @@ struct e1000_info {
#define FLAG_HAS_CTRLEXT_ON_LOAD (1 << 5)
#define FLAG_HAS_SWSM_ON_LOAD (1 << 6)
#define FLAG_HAS_JUMBO_FRAMES (1 << 7)
-#define FLAG_HAS_ASPM (1 << 8)
#define FLAG_HAS_STATS_ICR_ICT (1 << 9)
#define FLAG_HAS_STATS_PTC_PRC (1 << 10)
#define FLAG_HAS_SMART_POWER_DOWN (1 << 11)
diff --git a/drivers/net/e1000e/netdev.c b/drivers/net/e1000e/netdev.c
index 4fd2e23..ec427e2 100644
--- a/drivers/net/e1000e/netdev.c
+++ b/drivers/net/e1000e/netdev.c
@@ -3511,6 +3511,33 @@ static int e1000_suspend(struct pci_dev *pdev, pm_message_t state)
return 0;
}
+static void e1000e_disable_l1aspm(struct pci_dev *pdev)
+{
+ int pos;
+ u32 cap;
+ u16 val;
+
+ /*
+ * 82573 workaround - disable L1 ASPM on mobile chipsets
+ *
+ * L1 ASPM on various mobile (ich7) chipsets do not behave properly
+ * resulting in lost data or garbage information on the pci-e link
+ * level. This could result in (false) bad EEPROM checksum errors,
+ * long ping times (up to 2s) or even a system freeze/hang.
+ *
+ * Unfortunately this feature saves about 1W power consumption when
+ * active.
+ */
+ pos = pci_find_capability(pdev, PCI_CAP_ID_EXP);
+ pci_read_config_dword(pdev, pos + PCI_EXP_LNKCAP, &cap);
+ pci_read_config_word(pdev, pos + PCI_EXP_LNKCTL, &val);
+ if (val & 0x2) {
+ dev_warn(&pdev->dev, "Disabling L1 ASPM\n");
+ val &= ~0x2;
+ pci_write_config_word(pdev, pos + PCI_EXP_LNKCTL, val);
+ }
+}
+
#ifdef CONFIG_PM
static int e1000_resume(struct pci_dev *pdev)
{
@@ -3521,6 +3548,7 @@ static int e1000_resume(struct pci_dev *pdev)
pci_set_power_state(pdev, PCI_D0);
pci_restore_state(pdev);
+ e1000e_disable_l1aspm(pdev);
err = pci_enable_device(pdev);
if (err) {
dev_err(&pdev->dev,
@@ -3621,6 +3649,7 @@ static pci_ers_result_t e1000_io_slot_reset(struct pci_dev *pdev)
struct e1000_adapter *adapter = netdev_priv(netdev);
struct e1000_hw *hw = &adapter->hw;
+ e1000e_disable_l1aspm(pdev);
if (pci_enable_device(pdev)) {
dev_err(&pdev->dev,
"Cannot re-enable PCI device after reset.\n");
@@ -3722,6 +3751,7 @@ static int __devinit e1000_probe(struct pci_dev *pdev,
u16 eeprom_data = 0;
u16 eeprom_apme_mask = E1000_EEPROM_APME;
+ e1000e_disable_l1aspm(pdev);
err = pci_enable_device(pdev);
if (err)
return err;
diff --git a/drivers/net/e1000e/param.c b/drivers/net/e1000e/param.c
index 3327892..df266c3 100644
--- a/drivers/net/e1000e/param.c
+++ b/drivers/net/e1000e/param.c
@@ -262,13 +262,6 @@ void __devinit e1000e_check_options(struct e1000_adapter *adapter)
.max = MAX_RXDELAY } }
};
- /* modify min and default if 82573 for slow ping w/a,
- * a value greater than 8 needs to be set for RDTR */
- if (adapter->flags & FLAG_HAS_ASPM) {
- opt.def = 32;
- opt.arg.r.min = 8;
- }
-
if (num_RxIntDelay > bd) {
adapter->rx_int_delay = RxIntDelay[bd];
e1000_validate_option(&adapter->rx_int_delay, &opt,
next prev parent reply other threads:[~2007-10-31 22:22 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2007-10-31 22:21 [PATCH 1/4] e1000e: alternate MAC address support Auke Kok
2007-10-31 22:22 ` Auke Kok [this message]
2007-10-31 22:22 ` [PATCH 3/4] e1000/e1000e: Move PCI-Express device IDs over to e1000e Auke Kok
2007-10-31 22:22 ` [PATCH 4/4] ixgbe: Fix copper PHY initialization code Auke Kok
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20071031222200.17411.52942.stgit@localhost.localdomain \
--to=auke-jan.h.kok@intel.com \
--cc=jeff@garzik.org \
--cc=jesse.brandeburg@intel.com \
--cc=john.ronciak@intel.com \
--cc=netdev@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.