From: Ben Dooks <ben-linux@fluff.org>
To: Tony Lindgren <tony@atomide.com>
Cc: i2c@lm-sensors.org, Paul Walmsley <paul@pwsan.com>,
linux-omap@vger.kernel.org
Subject: Re: [i2c] [PATCH 2/8] i2c-omap: Close suspected race between omap_i2c_idle() and omap_i2c_isr()
Date: Mon, 29 Sep 2008 23:21:47 +0100 [thread overview]
Message-ID: <20080929222147.GO2716@fluff.org.uk> (raw)
In-Reply-To: <1222329234-31473-3-git-send-email-tony@atomide.com>
On Thu, Sep 25, 2008 at 10:53:48AM +0300, Tony Lindgren wrote:
> From: Paul Walmsley <paul@pwsan.com>
>
> omap_i2c_idle() sets an internal flag, "dev->idle", instructing its
> ISR to decline interrupts. It sets this flag before it actually masks
> the interrupts on the I2C controller. This is problematic, since an
> I2C interrupt could arrive after dev->idle is set, but before the
> interrupt source is masked. When this happens, Linux disables the I2C
> controller's IRQ, causing all future transactions on the bus to fail.
>
> Symptoms, happening on about 7% of boots:
>
> irq 56: nobody cared (try booting with the "irqpoll" option)
> <warning traceback here>
> Disabling IRQ #56
> i2c_omap i2c_omap.1: controller timed out
>
> In omap_i2c_idle(), this patch sets dev->idle only after the interrupt
> mask write to the I2C controller has left the ARM write buffer.
> That's probably the major offender. For additional prophylaxis, in
> omap_i2c_unidle(), the patch clears the dev->idle flag before
> interrupts are enabled, rather than afterwards.
>
> The patch has survived twenty-two reboots on the 3430SDP here without
> wedging I2C1. Not absolutely dispositive, but promising!
that looks ok.
> Signed-off-by: Paul Walmsley <paul@pwsan.com>
> Signed-off-by: Tony Lindgren <tony@atomide.com>
> ---
> drivers/i2c/busses/i2c-omap.c | 10 ++++++++--
> 1 files changed, 8 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c
> index cfb76f5..a06ad42 100644
> --- a/drivers/i2c/busses/i2c-omap.c
> +++ b/drivers/i2c/busses/i2c-omap.c
> @@ -181,22 +181,28 @@ static void omap_i2c_unidle(struct omap_i2c_dev *dev)
> if (dev->iclk != NULL)
> clk_enable(dev->iclk);
> clk_enable(dev->fclk);
> + dev->idle = 0;
> if (dev->iestate)
> omap_i2c_write_reg(dev, OMAP_I2C_IE_REG, dev->iestate);
> - dev->idle = 0;
> }
>
> static void omap_i2c_idle(struct omap_i2c_dev *dev)
> {
> u16 iv;
>
> - dev->idle = 1;
> dev->iestate = omap_i2c_read_reg(dev, OMAP_I2C_IE_REG);
> omap_i2c_write_reg(dev, OMAP_I2C_IE_REG, 0);
> if (dev->rev1)
> iv = omap_i2c_read_reg(dev, OMAP_I2C_IV_REG); /* Read clears */
> else
> omap_i2c_write_reg(dev, OMAP_I2C_STAT_REG, dev->iestate);
> + /*
> + * The wmb() is to ensure that the I2C interrupt mask write
> + * reaches the I2C controller before the dev->idle store
> + * occurs.
> + */
> + wmb();
> + dev->idle = 1;
> clk_disable(dev->fclk);
> if (dev->iclk != NULL)
> clk_disable(dev->iclk);
> --
> 1.5.6.rc3.21.g8c6b5
>
>
> _______________________________________________
> i2c mailing list
> i2c@lm-sensors.org
> http://lists.lm-sensors.org/mailman/listinfo/i2c
--
Ben (ben@fluff.org, http://www.fluff.org/)
'a smiley only costs 4 bytes'
next prev parent reply other threads:[~2008-09-29 22:21 UTC|newest]
Thread overview: 34+ messages / expand[flat|nested] mbox.gz Atom feed top
2008-09-25 7:53 [PATCH 0/8] Updates for i2c-omap from linux-omap tree for review, v2 Tony Lindgren
2008-09-25 7:53 ` [PATCH 1/8] i2c-omap: Do not use interruptible wait call in omap_i2c_xfer_msg Tony Lindgren
2008-09-25 7:53 ` [PATCH 2/8] i2c-omap: Close suspected race between omap_i2c_idle() and omap_i2c_isr() Tony Lindgren
2008-09-25 7:53 ` [PATCH 3/8] i2c-omap: Add high-speed support to omap-i2c Tony Lindgren
2008-09-25 7:53 ` [PATCH 4/8] i2c-omap: FIFO handling support and broken hw workaround for i2c-omap Tony Lindgren
2008-09-25 7:53 ` [PATCH 5/8] i2c-omap: Add support on 34xx Tony Lindgren
2008-09-25 7:53 ` [PATCH 6/8] i2c-omap: Mark init-only functions as __init Tony Lindgren
2008-09-25 7:53 ` [PATCH 7/8] i2c-omap: Don't compile in OMAP15xx I2C ISR for non-OMAP15xx builds Tony Lindgren
2008-09-25 7:53 ` [PATCH 8/8] i2c-omap: Clean-up i2c-omap Tony Lindgren
2008-09-25 11:40 ` [PATCH 8/8] i2c-omap: Clean-up i2c-omap, v3 Tony Lindgren
2008-09-29 22:31 ` [i2c] [PATCH 8/8] i2c-omap: Clean-up i2c-omap Ben Dooks
2008-10-17 15:41 ` Tony Lindgren
[not found] ` <1222329234-31473-9-git-send-email-tony-4v6yS6AI5VpBDgjK7y7TUQ@public.gmane.org>
2008-10-17 15:47 ` [PATCH 9/8] i2c-omap: fix I2C timeouts due to recursive omap_i2c_{un, }idle() Tony Lindgren
2008-09-29 22:29 ` [i2c] [PATCH 7/8] i2c-omap: Don't compile in OMAP15xx I2C ISR for non-OMAP15xx builds Ben Dooks
2008-09-29 23:06 ` David Brownell
2008-09-30 5:35 ` Paul Walmsley
2008-09-30 5:36 ` Paul Walmsley
2008-10-17 15:40 ` Tony Lindgren
2008-09-29 22:30 ` [i2c] [PATCH 6/8] i2c-omap: Mark init-only functions as __init Ben Dooks
2008-10-17 15:39 ` Tony Lindgren
2008-10-17 17:07 ` Tony Lindgren
2008-09-29 22:28 ` [i2c] [PATCH 5/8] i2c-omap: Add support on 34xx Ben Dooks
2008-10-17 15:38 ` Tony Lindgren
2008-09-25 11:39 ` [PATCH 4/8] i2c-omap: FIFO handling support and broken hw workaround for i2c-omap, v3 Tony Lindgren
2008-09-29 22:27 ` [i2c] [PATCH 4/8] i2c-omap: FIFO handling support and broken hw workaround for i2c-omap Ben Dooks
2008-09-29 22:25 ` [i2c] [PATCH 3/8] i2c-omap: Add high-speed support to omap-i2c Ben Dooks
2008-10-17 15:37 ` Tony Lindgren
2008-09-29 22:21 ` Ben Dooks [this message]
2008-09-29 22:21 ` [i2c] [PATCH 1/8] i2c-omap: Do not use interruptible wait call in omap_i2c_xfer_msg Ben Dooks
2008-09-30 11:51 ` Jarkko Nikula
2008-10-17 15:35 ` Tony Lindgren
2008-09-29 22:23 ` [i2c] [PATCH 0/8] Updates for i2c-omap from linux-omap tree for review, v2 Ben Dooks
2008-09-30 5:35 ` Tony Lindgren
2008-10-17 16:04 ` git-pull request for i2c-omap changes (Re: [i2c] [PATCH 0/8] Updates for i2c-omap from linux-omap tree for review, v2) Tony Lindgren
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20080929222147.GO2716@fluff.org.uk \
--to=ben-linux@fluff.org \
--cc=i2c@lm-sensors.org \
--cc=linux-omap@vger.kernel.org \
--cc=paul@pwsan.com \
--cc=tony@atomide.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.