* [Buildroot] uImage build error @ 2010-08-25 21:41 Choi, David 2010-08-25 21:54 ` Marcus Osdoba 0 siblings, 1 reply; 5+ messages in thread From: Choi, David @ 2010-08-25 21:41 UTC (permalink / raw) To: buildroot Hi all, I am new to buildroot. The version that I use is v2010.05(stable version) As you see the attached, I almost the default value except mips(little endian mode). My Linux version is 2.6.33.5(default version) and configuration is tb0229_defconfig. Whenever I have tried to build uImage, I have gotten an error message saying "make[1]: *** No rule to make target `uImage`. Stop. (Even though I have tried with v2010.08(rc1), I had the same error message) Any comment will be highly appreciated. Regards, David J. Choi -------------- next part -------------- An HTML attachment was scrubbed... URL: <http://lists.busybox.net/pipermail/buildroot/attachments/20100825/f82b877f/attachment-0001.html> -------------- next part -------------- A non-text attachment was scrubbed... Name: linux-2.6.33.5.config Type: application/octet-stream Size: 27679 bytes Desc: linux-2.6.33.5.config URL: <http://lists.busybox.net/pipermail/buildroot/attachments/20100825/f82b877f/attachment-0002.obj> -------------- next part -------------- A non-text attachment was scrubbed... Name: buildroot2010-05.config Type: application/octet-stream Size: 17543 bytes Desc: buildroot2010-05.config URL: <http://lists.busybox.net/pipermail/buildroot/attachments/20100825/f82b877f/attachment-0003.obj> ^ permalink raw reply [flat|nested] 5+ messages in thread
* [Buildroot] uImage build error 2010-08-25 21:41 [Buildroot] uImage build error Choi, David @ 2010-08-25 21:54 ` Marcus Osdoba 2010-08-27 0:26 ` Choi, David 0 siblings, 1 reply; 5+ messages in thread From: Marcus Osdoba @ 2010-08-25 21:54 UTC (permalink / raw) To: buildroot Am 25.08.2010 23:41, schrieb Choi, David: > > Hi all, > > I am new to buildroot. The version that I use is v2010.05(stable version) > > As you see the attached, I almost the default value except mips(little > endian mode). > > My Linux version is 2.6.33.5(default version) and configuration is > tb0229_defconfig. > > Whenever I have tried to build uImage, I have gotten an error message > saying "make[1]: *** No rule to make target `uImage`. Stop. > > (Even though I have tried with v2010.08(rc1), I had the same error > message) > Hi, Make sure to run 2010.08(rc1) or higher (there were some patches in the past concerning kernel image building). Please activate the U-Boot bootloader. This should compile a mkimage which will be needed for creating an uImage. >make menuconfig (activate u-boot and/or kernel building if you want this) >make ( Are you trying to run make uImage after deflating? This is not the linux kernel. Buildroot is an independant project. Please read docu page first: http://buildroot.uclibc.org/downloads/buildroot.html ) Regards, Marcus -------------- next part -------------- An HTML attachment was scrubbed... URL: <http://lists.busybox.net/pipermail/buildroot/attachments/20100825/1925be16/attachment.html> ^ permalink raw reply [flat|nested] 5+ messages in thread
* [Buildroot] uImage build error 2010-08-25 21:54 ` Marcus Osdoba @ 2010-08-27 0:26 ` Choi, David 2010-08-27 8:01 ` Thomas Petazzoni 0 siblings, 1 reply; 5+ messages in thread From: Choi, David @ 2010-08-27 0:26 UTC (permalink / raw) To: buildroot Hello Marcus, Thank you for your e-mail. Basically I understand Buildroot is an independent from linux kernel, as you pointed out in your previous e-mail. The reason I posted the question is that users can select [kernel binary format] from [make menuconfig] in the buildroot of v2010.08-rc1. As I need u-boot and linux kernel, I put the need information properly from the [make menuconfig]. When I choose vmlinux as a kernel binary format, I can see the root file system, kernel and u-boot in the output/image direcoty(rootfs.initcramfs, u-boot.bin and vmlinux.bin). But when I change uImage as a kernel binary format, there is an error message( make[1]: ***No rule to make target uImage. Stop). I also read the doc that you pointed but I can not find the clue to fix this issue. If there is misunderstanding at my side, please make me correct. Regards, David J. Choi ________________________________ From: buildroot-bounces@busybox.net [mailto:buildroot-bounces at busybox.net] On Behalf Of Marcus Osdoba Sent: Wednesday, August 25, 2010 2:54 PM To: buildroot at busybox.net Subject: Re: [Buildroot] uImage build error Am 25.08.2010 23:41, schrieb Choi, David: Hi all, I am new to buildroot. The version that I use is v2010.05(stable version) As you see the attached, I almost the default value except mips(little endian mode). My Linux version is 2.6.33.5(default version) and configuration is tb0229_defconfig. Whenever I have tried to build uImage, I have gotten an error message saying "make[1]: *** No rule to make target `uImage`. Stop. (Even though I have tried with v2010.08(rc1), I had the same error message) Hi, Make sure to run 2010.08(rc1) or higher (there were some patches in the past concerning kernel image building). Please activate the U-Boot bootloader. This should compile a mkimage which will be needed for creating an uImage. >make menuconfig (activate u-boot and/or kernel building if you want this) >make ( Are you trying to run make uImage after deflating? This is not the linux kernel. Buildroot is an independant project. Please read docu page first: http://buildroot.uclibc.org/downloads/buildroot.html ) Regards, Marcus -------------- next part -------------- An HTML attachment was scrubbed... URL: <http://lists.busybox.net/pipermail/buildroot/attachments/20100826/e2462082/attachment.html> ^ permalink raw reply [flat|nested] 5+ messages in thread
* [Buildroot] uImage build error 2010-08-27 0:26 ` Choi, David @ 2010-08-27 8:01 ` Thomas Petazzoni 2010-08-27 14:40 ` Choi, David 0 siblings, 1 reply; 5+ messages in thread From: Thomas Petazzoni @ 2010-08-27 8:01 UTC (permalink / raw) To: buildroot Hello David, On Thu, 26 Aug 2010 17:26:09 -0700 "Choi, David" <David.Choi@Micrel.Com> wrote: > Thank you for your e-mail. Basically I understand Buildroot is an > independent from linux kernel, as you pointed out in your previous > e-mail. > > The reason I posted the question is that users can select [kernel > binary format] from [make menuconfig] in the buildroot of > v2010.08-rc1. > > As I need u-boot and linux kernel, I put the need information properly > from the [make menuconfig]. When I choose vmlinux as a kernel binary > format, > > I can see the root file system, kernel and u-boot in the output/image > direcoty(rootfs.initcramfs, u-boot.bin and vmlinux.bin). > > But when I change uImage as a kernel binary format, there is an error > message( make[1]: ***No rule to make target uImage. Stop). From your previous post, I understand that you are building for MIPS. However, the kernel doesn't provide a "make uImage" target for the MIPS architecture: you have to produce the mkimage'd kernel manually. On the Buildroot side, we should just prevent you from selecting "uImage" if the architecture does not support it. Cheers, Thomas -- Thomas Petazzoni, Free Electrons Kernel, drivers, real-time and embedded Linux development, consulting, training and support. http://free-electrons.com ^ permalink raw reply [flat|nested] 5+ messages in thread
* [Buildroot] uImage build error 2010-08-27 8:01 ` Thomas Petazzoni @ 2010-08-27 14:40 ` Choi, David 0 siblings, 0 replies; 5+ messages in thread From: Choi, David @ 2010-08-27 14:40 UTC (permalink / raw) To: buildroot Hello Thomas & all, Thank you. I got it. Regards, David J. Choi -----Original Message----- From: buildroot-bounces@busybox.net [mailto:buildroot-bounces at busybox.net] On Behalf Of Thomas Petazzoni Sent: Friday, August 27, 2010 1:01 AM To: buildroot at busybox.net Subject: Re: [Buildroot] uImage build error Hello David, On Thu, 26 Aug 2010 17:26:09 -0700 "Choi, David" <David.Choi@Micrel.Com> wrote: > Thank you for your e-mail. Basically I understand Buildroot is an > independent from linux kernel, as you pointed out in your previous > e-mail. > > The reason I posted the question is that users can select [kernel > binary format] from [make menuconfig] in the buildroot of > v2010.08-rc1. > > As I need u-boot and linux kernel, I put the need information properly > from the [make menuconfig]. When I choose vmlinux as a kernel binary > format, > > I can see the root file system, kernel and u-boot in the output/image > direcoty(rootfs.initcramfs, u-boot.bin and vmlinux.bin). > > But when I change uImage as a kernel binary format, there is an error > message( make[1]: ***No rule to make target uImage. Stop). From your previous post, I understand that you are building for MIPS. However, the kernel doesn't provide a "make uImage" target for the MIPS architecture: you have to produce the mkimage'd kernel manually. On the Buildroot side, we should just prevent you from selecting "uImage" if the architecture does not support it. Cheers, Thomas -- Thomas Petazzoni, Free Electrons Kernel, drivers, real-time and embedded Linux development, consulting, training and support. http://free-electrons.com _______________________________________________ buildroot mailing list buildroot at busybox.net http://lists.busybox.net/mailman/listinfo/buildroot ^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2010-08-27 14:40 UTC | newest] Thread overview: 5+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2010-08-25 21:41 [Buildroot] uImage build error Choi, David 2010-08-25 21:54 ` Marcus Osdoba 2010-08-27 0:26 ` Choi, David 2010-08-27 8:01 ` Thomas Petazzoni 2010-08-27 14:40 ` Choi, David
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.