Re: [PATCH] mmc: mmci: Allow MMCI to request channels with information acquired from DT

[Lee Jones <lee.jones@linaro.org>]

> I think you can further simplify this, given that in the DT case we always
> allocate a zeroed mmci_platform_data for host->plat, so !plat cannot happen
> when we get here.

Okay, third time lucky. :)

diff --git a/drivers/mmc/host/mmci.c b/drivers/mmc/host/mmci.c
index 372e921..3260ab4 100644
--- a/drivers/mmc/host/mmci.c
+++ b/drivers/mmc/host/mmci.c
@@ -298,14 +298,16 @@ static void mmci_init_sg(struct mmci_host *host, struct mmc_data *data)
  * no custom DMA interfaces are supported.
  */
 #ifdef CONFIG_DMA_ENGINE
-static void mmci_dma_setup(struct mmci_host *host)
+static void mmci_dma_setup(struct amba_device *dev,
+			   struct mmci_host *host)
 {
+	struct device_node *np = dev->dev.of_node;
 	struct mmci_platform_data *plat = host->plat;
 	const char *rxname, *txname;
 	dma_cap_mask_t mask;
 
-	if (!plat || !plat->dma_filter) {
-		dev_info(mmc_dev(host->mmc), "no DMA platform data\n");
+	if (!(plat->dma_filter || np)) {
+		dev_info(mmc_dev(host->mmc), "no DMA platform data or DT\n");
 		return;
 	}
 
@@ -321,19 +323,21 @@ static void mmci_dma_setup(struct mmci_host *host)
 	 * attempt to use it bidirectionally, however if it is
 	 * is specified but cannot be located, DMA will be disabled.
 	 */
-	if (plat->dma_rx_param) {
-		host->dma_rx_channel = dma_request_channel(mask,
-							   plat->dma_filter,
-							   plat->dma_rx_param);
+	if (plat->dma_rx_param || np) {
+		host->dma_rx_channel = dma_request_slave_channel_compat(mask,
+								plat->dma_filter,
+								plat->dma_rx_param,
+								&dev->dev, "rx");
 		/* E.g if no DMA hardware is present */
 		if (!host->dma_rx_channel)
 			dev_err(mmc_dev(host->mmc), "no RX DMA channel\n");
 	}
 
-	if (plat->dma_tx_param) {
-		host->dma_tx_channel = dma_request_channel(mask,
-							   plat->dma_filter,
-							   plat->dma_tx_param);
+	if (plat->dma_tx_param || np) {
+		host->dma_tx_channel = dma_request_slave_channel_compat(mask,
+								plat->dma_filter,
+								plat->dma_tx_param,
+								&dev->dev, "tx");
 		if (!host->dma_tx_channel)
 			dev_warn(mmc_dev(host->mmc), "no TX DMA channel\n");
 	} else {
@@ -1538,7 +1542,7 @@ static int mmci_probe(struct amba_device *dev,
 		 amba_rev(dev), (unsigned long long)dev->res.start,
 		 dev->irq[0], dev->irq[1]);
 
-	mmci_dma_setup(host);
+	mmci_dma_setup(dev, host);
 
 	pm_runtime_set_autosuspend_delay(&dev->dev, 50);
 	pm_runtime_use_autosuspend(&dev->dev);

-- 
Lee Jones
Linaro ST-Ericsson Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog