From: Felipe Balbi <balbi@ti.com>
To: George McCollister <george.mccollister@gmail.com>
Cc: "Rob Herring" <robh+dt@kernel.org>,
"Pawel Moll" <pawel.moll@arm.com>,
"Mark Rutland" <mark.rutland@arm.com>,
"Ian Campbell" <ijc+devicetree@hellion.org.uk>,
"Kumar Gala" <galak@codeaurora.org>,
"Russell King" <linux@arm.linux.org.uk>,
"Benoît Cousson" <bcousson@baylibre.com>,
"Tony Lindgren" <tony@atomide.com>, "Nishanth Menon" <nm@ti.com>,
"Florian Vaussard" <florian.vaussard@epfl.ch>,
"Tomi Valkeinen" <tomi.valkeinen@ti.com>,
"Joachim Eastwood" <manabian@gmail.com>,
"Felipe Balbi" <balbi@ti.com>,
"Lokesh Vutla" <lokeshvutla@ti.com>,
"Carlos Garcia" <carlos@cgarcia.org>,
"open list:OPEN FIRMWARE AND..." <devicetree@vger.kernel.org>,
"open list" <linux-kernel@vger.kernel.org>,
"moderated list:ARM PORT" <linux-arm-kernel@lists.infradead.org>,
"open list:OMAP DEVICE TREE..." <linux-omap@vger.kernel.org>
Subject: Re: [PATCH v2 2/2] ARM: dts: Add devicetree for NovaTech OrionLXm
Date: Mon, 17 Nov 2014 13:09:00 -0600 [thread overview]
Message-ID: <20141117190847.GA4857@saruman> (raw)
In-Reply-To: <1416250957-11065-2-git-send-email-george.mccollister@gmail.com>
[-- Attachment #1: Type: text/plain, Size: 12607 bytes --]
On Mon, Nov 17, 2014 at 01:02:35PM -0600, George McCollister wrote:
> This adds the NovaTech OrionLXm which is based on the AM335x SoC
> http://www.novatechweb.com/substation-automation/orionlxm/
>
> RAM: 512MiB
> Flash: 4GB eMMC
> Ethernet PHYs: 2x Micrel KSZ8041FTLI
> USB ports are used internally by the expansion cards.
> Internal micro SD slot is available.
>
> Signed-off-by: George McCollister <george.mccollister@gmail.com>
this looks might better to my eyes:
Reviewed-by: Felipe Balbi <balbi@ti.com>
> ---
> .../devicetree/bindings/arm/omap/omap.txt | 3 +
> arch/arm/boot/dts/Makefile | 3 +-
> arch/arm/boot/dts/am335x-lxm.dts | 362 +++++++++++++++++++++
> 3 files changed, 367 insertions(+), 1 deletion(-)
> create mode 100644 arch/arm/boot/dts/am335x-lxm.dts
>
> diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt
> index ddd9bcd..4f6a82c 100644
> --- a/Documentation/devicetree/bindings/arm/omap/omap.txt
> +++ b/Documentation/devicetree/bindings/arm/omap/omap.txt
> @@ -132,6 +132,9 @@ Boards:
> - AM335X Bone : Low cost community board
> compatible = "ti,am335x-bone", "ti,am33xx", "ti,omap3"
>
> +- AM335X OrionLXm : Substation Automation Platform
> + compatible = "novatech,am335x-lxm", "ti,am33xx"
> +
> - OMAP5 EVM : Evaluation Module
> compatible = "ti,omap5-evm", "ti,omap5"
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 38c89ca..454ee6c 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -331,7 +331,8 @@ dtb-$(CONFIG_SOC_AM33XX) += am335x-base0033.dtb \
> am335x-evm.dtb \
> am335x-evmsk.dtb \
> am335x-nano.dtb \
> - am335x-pepper.dtb
> + am335x-pepper.dtb \
> + am335x-lxm.dtb
> dtb-$(CONFIG_ARCH_OMAP4) += omap4-duovero-parlor.dtb \
> omap4-panda.dtb \
> omap4-panda-a4.dtb \
> diff --git a/arch/arm/boot/dts/am335x-lxm.dts b/arch/arm/boot/dts/am335x-lxm.dts
> new file mode 100644
> index 0000000..7266a00
> --- /dev/null
> +++ b/arch/arm/boot/dts/am335x-lxm.dts
> @@ -0,0 +1,362 @@
> +/*
> + * Copyright (C) 2014 NovaTech LLC - http://www.novatechweb.com
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + */
> +/dts-v1/;
> +
> +#include "am33xx.dtsi"
> +
> +/ {
> + model = "NovaTech OrionLXm";
> + compatible = "novatech,am335x-lxm", "ti,am33xx";
> +
> + cpus {
> + cpu@0 {
> + cpu0-supply = <&vdd1_reg>;
> + };
> + };
> +
> + memory {
> + device_type = "memory";
> + reg = <0x80000000 0x20000000>; /* 512 MB */
> + };
> +
> + /* Power supply provides a fixed 5V @2A */
> + vbat: fixedregulator@0 {
> + compatible = "regulator-fixed";
> + regulator-name = "vbat";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-boot-on;
> + };
> +
> + /* Power supply provides a fixed 3.3V @3A */
> + vmmcsd_fixed: fixedregulator@1 {
> + compatible = "regulator-fixed";
> + regulator-name = "vmmcsd_fixed";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + };
> +};
> +
> +&am33xx_pinmux {
> + mmc1_pins: pinmux_mmc1_pins {
> + pinctrl-single,pins = <
> + 0xf0 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat3 */
> + 0xf4 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat2 */
> + 0xf8 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat1 */
> + 0xfc (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat0 */
> + 0x100 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_clk */
> + 0x104 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_cmd */
> + >;
> + };
> +
> + i2c0_pins: pinmux_i2c0_pins {
> + pinctrl-single,pins = <
> + 0x188 (PIN_INPUT | MUX_MODE0) /* i2c0_sda.i2c0_sda */
> + 0x18c (PIN_INPUT | MUX_MODE0) /* i2c0_scl.i2c0_scl */
> + >;
> + };
> +
> + cpsw_default: cpsw_default {
> + pinctrl-single,pins = <
> + /* Slave 1 */
> + 0x64 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_int */
> + 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE1) /* rmii1_crs_dv */
> + 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* rmii1_rxer */
> + 0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* rmii1_txen */
> + 0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* rmii1_td1 */
> + 0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* rmii1_td0 */
> + 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE1) /* rmii1_rd1 */
> + 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* rmii1_rd0 */
> + 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* rmii1_refclk */
> +
> + /* Slave 2 */
> + 0x40 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* rmii2_txen */
> + 0x50 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* rmii2_td1 */
> + 0x54 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* rmii2_td0 */
> + 0x68 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* rmii2_rd1 */
> + 0x6c (PIN_INPUT_PULLDOWN | MUX_MODE3) /* rmii2_rd0 */
> + 0x70 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* rmii2_crs_dv */
> + 0x74 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* rmii2_rxer */
> + 0x78 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_int */
> + 0x108 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* rmii2_refclk */
> + >;
> + };
> +
> + cpsw_sleep: cpsw_sleep {
> + pinctrl-single,pins = <
> + /* Slave 1 reset value */
> + 0x64 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_int */
> + 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_crs_dv */
> + 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_rxer */
> + 0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_txen */
> + 0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_td1 */
> + 0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_td0 */
> + 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_rd1 */
> + 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_rd0 */
> + 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_refclk */
> +
> + /* Slave 2 reset value*/
> + 0x40 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_txen */
> + 0x50 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_td1 */
> + 0x54 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_td0 */
> + 0x68 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_rd1 */
> + 0x6c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_rd0 */
> + 0x70 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_crs_dv */
> + 0x74 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_rxer */
> + 0x78 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_int */
> + 0x108 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_refclk */
> + >;
> + };
> +
> + davinci_mdio_default: davinci_mdio_default {
> + pinctrl-single,pins = <
> + /* MDIO */
> + 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */
> + 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */
> + >;
> + };
> +
> + davinci_mdio_sleep: davinci_mdio_sleep {
> + pinctrl-single,pins = <
> + /* MDIO reset value */
> + 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7)
> + 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7)
> + >;
> + };
> +
> + emmc_pins: pinmux_emmc_pins {
> + pinctrl-single,pins = <
> + 0x80 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn1.mmc1_clk */
> + 0x84 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn2.mmc1_cmd */
> + 0x00 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad0.mmc1_dat0 */
> + 0x04 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad1.mmc1_dat1 */
> + 0x08 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad2.mmc1_dat2 */
> + 0x0c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad3.mmc1_dat3 */
> + 0x10 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad4.mmc1_dat4 */
> + 0x14 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad5.mmc1_dat5 */
> + 0x18 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad6.mmc1_dat6 */
> + 0x1c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad7.mmc1_dat7 */
> + >;
> + };
> +
> + uart0_pins: pinmux_uart0_pins {
> + pinctrl-single,pins = <
> + 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */
> + 0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */
> + >;
> + };
> +};
> +
> +&i2c0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c0_pins>;
> +
> + status = "okay";
> + clock-frequency = <400000>;
> +
> + serial_config1: serial_config1@20 {
> + compatible = "nxp,pca9539";
> + reg = <0x20>;
> + };
> +
> + serial_config2: serial_config2@21 {
> + compatible = "nxp,pca9539";
> + reg = <0x21>;
> + };
> +
> + tps: tps@2d {
> + compatible = "ti,tps65910";
> + reg = <0x2d>;
> + };
> +};
> +
> +/include/ "tps65910.dtsi"
> +
> +&tps {
> + vcc1-supply = <&vbat>;
> + vcc2-supply = <&vbat>;
> + vcc3-supply = <&vbat>;
> + vcc4-supply = <&vbat>;
> + vcc5-supply = <&vbat>;
> + vcc6-supply = <&vbat>;
> + vcc7-supply = <&vbat>;
> + vccio-supply = <&vbat>;
> +
> + regulators {
> + /* vrtc - unused */
> +
> + vio_reg: regulator@1 {
> + regulator-name = "vio_1v5,ddr";
> + regulator-min-microvolt = <1500000>;
> + regulator-max-microvolt = <1500000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + vdd1_reg: regulator@2 {
> + regulator-name = "vdd1,mpu";
> + regulator-min-microvolt = <600000>;
> + regulator-max-microvolt = <1500000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + vdd2_reg: regulator@3 {
> + regulator-name = "vdd2_1v1,core";
> + regulator-min-microvolt = <1100000>;
> + regulator-max-microvolt = <1100000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + /* vdd3 - unused */
> +
> + /* vdig1 - unused */
> +
> + vdig2_reg: regulator@6 {
> + regulator-name = "vdig2_1v8,vdds_pll";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + /* vpll - unused */
> +
> + vdac_reg: regulator@8 {
> + regulator-name = "vdac_1v8,vdds";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + vaux1_reg: regulator@9 {
> + regulator-name = "vaux1_1v8,usb";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + vaux2_reg: regulator@10 {
> + regulator-name = "vaux2_3v3,io";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + vaux33_reg: regulator@11 {
> + regulator-name = "vaux33_3v3,usb";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + vmmc_reg: regulator@12 {
> + regulator-name = "vmmc_3v3,io";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> + };
> +};
> +
> +&sham {
> + status = "okay";
> +};
> +
> +&aes {
> + status = "okay";
> +};
> +
> +&uart0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart0_pins>;
> +
> + status = "okay";
> +};
> +
> +&usb {
> + status = "okay";
> +};
> +
> +&usb_ctrl_mod {
> + status = "okay";
> +};
> +
> +&usb0_phy {
> + status = "okay";
> +};
> +
> +&usb1_phy {
> + status = "okay";
> +};
> +
> +&usb0 {
> + status = "okay";
> + dr_mode = "host";
> +};
> +
> +&usb1 {
> + status = "okay";
> + dr_mode = "host";
> +};
> +
> +&cppi41dma {
> + status = "okay";
> +};
> +
> +&cpsw_emac0 {
> + phy_id = <&davinci_mdio>, <5>;
> + phy-mode = "rmii";
> + dual_emac_res_vlan = <2>;
> +};
> +
> +&cpsw_emac1 {
> + phy_id = <&davinci_mdio>, <4>;
> + phy-mode = "rmii";
> + dual_emac_res_vlan = <3>;
> +};
> +
> +&mac {
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&cpsw_default>;
> + pinctrl-1 = <&cpsw_sleep>;
> + dual_emac = <1>;
> + status = "okay";
> +};
> +
> +&davinci_mdio {
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&davinci_mdio_default>;
> + pinctrl-1 = <&davinci_mdio_sleep>;
> + status = "okay";
> +};
> +
> +&mmc1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&mmc1_pins>;
> + vmmc-supply = <&vmmcsd_fixed>;
> + bus-width = <4>;
> + status = "okay";
> +};
> +
> +&mmc2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&emmc_pins>;
> + vmmc-supply = <&vmmcsd_fixed>;
> + bus-width = <8>;
> + ti,non-removable;
> + status = "okay";
> +};
> +
> --
> 2.1.0
>
--
balbi
[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 819 bytes --]
WARNING: multiple messages have this Message-ID (diff)
From: balbi@ti.com (Felipe Balbi)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH v2 2/2] ARM: dts: Add devicetree for NovaTech OrionLXm
Date: Mon, 17 Nov 2014 13:09:00 -0600 [thread overview]
Message-ID: <20141117190847.GA4857@saruman> (raw)
In-Reply-To: <1416250957-11065-2-git-send-email-george.mccollister@gmail.com>
On Mon, Nov 17, 2014 at 01:02:35PM -0600, George McCollister wrote:
> This adds the NovaTech OrionLXm which is based on the AM335x SoC
> http://www.novatechweb.com/substation-automation/orionlxm/
>
> RAM: 512MiB
> Flash: 4GB eMMC
> Ethernet PHYs: 2x Micrel KSZ8041FTLI
> USB ports are used internally by the expansion cards.
> Internal micro SD slot is available.
>
> Signed-off-by: George McCollister <george.mccollister@gmail.com>
this looks might better to my eyes:
Reviewed-by: Felipe Balbi <balbi@ti.com>
> ---
> .../devicetree/bindings/arm/omap/omap.txt | 3 +
> arch/arm/boot/dts/Makefile | 3 +-
> arch/arm/boot/dts/am335x-lxm.dts | 362 +++++++++++++++++++++
> 3 files changed, 367 insertions(+), 1 deletion(-)
> create mode 100644 arch/arm/boot/dts/am335x-lxm.dts
>
> diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt
> index ddd9bcd..4f6a82c 100644
> --- a/Documentation/devicetree/bindings/arm/omap/omap.txt
> +++ b/Documentation/devicetree/bindings/arm/omap/omap.txt
> @@ -132,6 +132,9 @@ Boards:
> - AM335X Bone : Low cost community board
> compatible = "ti,am335x-bone", "ti,am33xx", "ti,omap3"
>
> +- AM335X OrionLXm : Substation Automation Platform
> + compatible = "novatech,am335x-lxm", "ti,am33xx"
> +
> - OMAP5 EVM : Evaluation Module
> compatible = "ti,omap5-evm", "ti,omap5"
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 38c89ca..454ee6c 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -331,7 +331,8 @@ dtb-$(CONFIG_SOC_AM33XX) += am335x-base0033.dtb \
> am335x-evm.dtb \
> am335x-evmsk.dtb \
> am335x-nano.dtb \
> - am335x-pepper.dtb
> + am335x-pepper.dtb \
> + am335x-lxm.dtb
> dtb-$(CONFIG_ARCH_OMAP4) += omap4-duovero-parlor.dtb \
> omap4-panda.dtb \
> omap4-panda-a4.dtb \
> diff --git a/arch/arm/boot/dts/am335x-lxm.dts b/arch/arm/boot/dts/am335x-lxm.dts
> new file mode 100644
> index 0000000..7266a00
> --- /dev/null
> +++ b/arch/arm/boot/dts/am335x-lxm.dts
> @@ -0,0 +1,362 @@
> +/*
> + * Copyright (C) 2014 NovaTech LLC - http://www.novatechweb.com
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + */
> +/dts-v1/;
> +
> +#include "am33xx.dtsi"
> +
> +/ {
> + model = "NovaTech OrionLXm";
> + compatible = "novatech,am335x-lxm", "ti,am33xx";
> +
> + cpus {
> + cpu at 0 {
> + cpu0-supply = <&vdd1_reg>;
> + };
> + };
> +
> + memory {
> + device_type = "memory";
> + reg = <0x80000000 0x20000000>; /* 512 MB */
> + };
> +
> + /* Power supply provides a fixed 5V @2A */
> + vbat: fixedregulator at 0 {
> + compatible = "regulator-fixed";
> + regulator-name = "vbat";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-boot-on;
> + };
> +
> + /* Power supply provides a fixed 3.3V @3A */
> + vmmcsd_fixed: fixedregulator at 1 {
> + compatible = "regulator-fixed";
> + regulator-name = "vmmcsd_fixed";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + };
> +};
> +
> +&am33xx_pinmux {
> + mmc1_pins: pinmux_mmc1_pins {
> + pinctrl-single,pins = <
> + 0xf0 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat3 */
> + 0xf4 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat2 */
> + 0xf8 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat1 */
> + 0xfc (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat0 */
> + 0x100 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_clk */
> + 0x104 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_cmd */
> + >;
> + };
> +
> + i2c0_pins: pinmux_i2c0_pins {
> + pinctrl-single,pins = <
> + 0x188 (PIN_INPUT | MUX_MODE0) /* i2c0_sda.i2c0_sda */
> + 0x18c (PIN_INPUT | MUX_MODE0) /* i2c0_scl.i2c0_scl */
> + >;
> + };
> +
> + cpsw_default: cpsw_default {
> + pinctrl-single,pins = <
> + /* Slave 1 */
> + 0x64 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_int */
> + 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE1) /* rmii1_crs_dv */
> + 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* rmii1_rxer */
> + 0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* rmii1_txen */
> + 0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* rmii1_td1 */
> + 0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* rmii1_td0 */
> + 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE1) /* rmii1_rd1 */
> + 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* rmii1_rd0 */
> + 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* rmii1_refclk */
> +
> + /* Slave 2 */
> + 0x40 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* rmii2_txen */
> + 0x50 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* rmii2_td1 */
> + 0x54 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* rmii2_td0 */
> + 0x68 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* rmii2_rd1 */
> + 0x6c (PIN_INPUT_PULLDOWN | MUX_MODE3) /* rmii2_rd0 */
> + 0x70 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* rmii2_crs_dv */
> + 0x74 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* rmii2_rxer */
> + 0x78 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_int */
> + 0x108 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* rmii2_refclk */
> + >;
> + };
> +
> + cpsw_sleep: cpsw_sleep {
> + pinctrl-single,pins = <
> + /* Slave 1 reset value */
> + 0x64 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_int */
> + 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_crs_dv */
> + 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_rxer */
> + 0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_txen */
> + 0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_td1 */
> + 0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_td0 */
> + 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_rd1 */
> + 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_rd0 */
> + 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_refclk */
> +
> + /* Slave 2 reset value*/
> + 0x40 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_txen */
> + 0x50 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_td1 */
> + 0x54 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_td0 */
> + 0x68 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_rd1 */
> + 0x6c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_rd0 */
> + 0x70 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_crs_dv */
> + 0x74 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_rxer */
> + 0x78 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_int */
> + 0x108 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_refclk */
> + >;
> + };
> +
> + davinci_mdio_default: davinci_mdio_default {
> + pinctrl-single,pins = <
> + /* MDIO */
> + 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */
> + 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */
> + >;
> + };
> +
> + davinci_mdio_sleep: davinci_mdio_sleep {
> + pinctrl-single,pins = <
> + /* MDIO reset value */
> + 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7)
> + 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7)
> + >;
> + };
> +
> + emmc_pins: pinmux_emmc_pins {
> + pinctrl-single,pins = <
> + 0x80 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn1.mmc1_clk */
> + 0x84 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn2.mmc1_cmd */
> + 0x00 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad0.mmc1_dat0 */
> + 0x04 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad1.mmc1_dat1 */
> + 0x08 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad2.mmc1_dat2 */
> + 0x0c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad3.mmc1_dat3 */
> + 0x10 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad4.mmc1_dat4 */
> + 0x14 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad5.mmc1_dat5 */
> + 0x18 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad6.mmc1_dat6 */
> + 0x1c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad7.mmc1_dat7 */
> + >;
> + };
> +
> + uart0_pins: pinmux_uart0_pins {
> + pinctrl-single,pins = <
> + 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */
> + 0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */
> + >;
> + };
> +};
> +
> +&i2c0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c0_pins>;
> +
> + status = "okay";
> + clock-frequency = <400000>;
> +
> + serial_config1: serial_config1 at 20 {
> + compatible = "nxp,pca9539";
> + reg = <0x20>;
> + };
> +
> + serial_config2: serial_config2 at 21 {
> + compatible = "nxp,pca9539";
> + reg = <0x21>;
> + };
> +
> + tps: tps at 2d {
> + compatible = "ti,tps65910";
> + reg = <0x2d>;
> + };
> +};
> +
> +/include/ "tps65910.dtsi"
> +
> +&tps {
> + vcc1-supply = <&vbat>;
> + vcc2-supply = <&vbat>;
> + vcc3-supply = <&vbat>;
> + vcc4-supply = <&vbat>;
> + vcc5-supply = <&vbat>;
> + vcc6-supply = <&vbat>;
> + vcc7-supply = <&vbat>;
> + vccio-supply = <&vbat>;
> +
> + regulators {
> + /* vrtc - unused */
> +
> + vio_reg: regulator at 1 {
> + regulator-name = "vio_1v5,ddr";
> + regulator-min-microvolt = <1500000>;
> + regulator-max-microvolt = <1500000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + vdd1_reg: regulator at 2 {
> + regulator-name = "vdd1,mpu";
> + regulator-min-microvolt = <600000>;
> + regulator-max-microvolt = <1500000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + vdd2_reg: regulator at 3 {
> + regulator-name = "vdd2_1v1,core";
> + regulator-min-microvolt = <1100000>;
> + regulator-max-microvolt = <1100000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + /* vdd3 - unused */
> +
> + /* vdig1 - unused */
> +
> + vdig2_reg: regulator at 6 {
> + regulator-name = "vdig2_1v8,vdds_pll";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + /* vpll - unused */
> +
> + vdac_reg: regulator at 8 {
> + regulator-name = "vdac_1v8,vdds";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + vaux1_reg: regulator at 9 {
> + regulator-name = "vaux1_1v8,usb";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + vaux2_reg: regulator at 10 {
> + regulator-name = "vaux2_3v3,io";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + vaux33_reg: regulator at 11 {
> + regulator-name = "vaux33_3v3,usb";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + vmmc_reg: regulator at 12 {
> + regulator-name = "vmmc_3v3,io";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> + };
> +};
> +
> +&sham {
> + status = "okay";
> +};
> +
> +&aes {
> + status = "okay";
> +};
> +
> +&uart0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart0_pins>;
> +
> + status = "okay";
> +};
> +
> +&usb {
> + status = "okay";
> +};
> +
> +&usb_ctrl_mod {
> + status = "okay";
> +};
> +
> +&usb0_phy {
> + status = "okay";
> +};
> +
> +&usb1_phy {
> + status = "okay";
> +};
> +
> +&usb0 {
> + status = "okay";
> + dr_mode = "host";
> +};
> +
> +&usb1 {
> + status = "okay";
> + dr_mode = "host";
> +};
> +
> +&cppi41dma {
> + status = "okay";
> +};
> +
> +&cpsw_emac0 {
> + phy_id = <&davinci_mdio>, <5>;
> + phy-mode = "rmii";
> + dual_emac_res_vlan = <2>;
> +};
> +
> +&cpsw_emac1 {
> + phy_id = <&davinci_mdio>, <4>;
> + phy-mode = "rmii";
> + dual_emac_res_vlan = <3>;
> +};
> +
> +&mac {
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&cpsw_default>;
> + pinctrl-1 = <&cpsw_sleep>;
> + dual_emac = <1>;
> + status = "okay";
> +};
> +
> +&davinci_mdio {
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&davinci_mdio_default>;
> + pinctrl-1 = <&davinci_mdio_sleep>;
> + status = "okay";
> +};
> +
> +&mmc1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&mmc1_pins>;
> + vmmc-supply = <&vmmcsd_fixed>;
> + bus-width = <4>;
> + status = "okay";
> +};
> +
> +&mmc2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&emmc_pins>;
> + vmmc-supply = <&vmmcsd_fixed>;
> + bus-width = <8>;
> + ti,non-removable;
> + status = "okay";
> +};
> +
> --
> 2.1.0
>
--
balbi
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20141117/4be311fc/attachment-0001.sig>
next prev parent reply other threads:[~2014-11-17 19:09 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-11-17 19:02 [PATCH v2 1/2] of: Add vendor prefix for NovaTech LLC George McCollister
2014-11-17 19:02 ` George McCollister
2014-11-17 19:02 ` [PATCH v2 2/2] ARM: dts: Add devicetree for NovaTech OrionLXm George McCollister
2014-11-17 19:02 ` George McCollister
2014-11-17 19:02 ` George McCollister
2014-11-17 19:09 ` Felipe Balbi [this message]
2014-11-17 19:09 ` Felipe Balbi
2014-11-21 23:33 ` Tony Lindgren
2014-11-21 23:33 ` Tony Lindgren
2014-11-21 23:33 ` Tony Lindgren
2014-11-17 19:10 ` [PATCH v2 1/2] of: Add vendor prefix for NovaTech LLC Felipe Balbi
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20141117190847.GA4857@saruman \
--to=balbi@ti.com \
--cc=bcousson@baylibre.com \
--cc=carlos@cgarcia.org \
--cc=devicetree@vger.kernel.org \
--cc=florian.vaussard@epfl.ch \
--cc=galak@codeaurora.org \
--cc=george.mccollister@gmail.com \
--cc=ijc+devicetree@hellion.org.uk \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-omap@vger.kernel.org \
--cc=linux@arm.linux.org.uk \
--cc=lokeshvutla@ti.com \
--cc=manabian@gmail.com \
--cc=mark.rutland@arm.com \
--cc=nm@ti.com \
--cc=pawel.moll@arm.com \
--cc=robh+dt@kernel.org \
--cc=tomi.valkeinen@ti.com \
--cc=tony@atomide.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.