* [PATCH v2 2/2] ARM: dts: Add devicetree for NovaTech OrionLXm
@ 2014-11-17 19:02 ` George McCollister
0 siblings, 0 replies; 11+ messages in thread
From: George McCollister @ 2014-11-17 19:02 UTC (permalink / raw)
Cc: George McCollister, Rob Herring, Pawel Moll, Mark Rutland,
Ian Campbell, Kumar Gala, Russell King, Benoît Cousson,
Tony Lindgren, Nishanth Menon, Florian Vaussard, Tomi Valkeinen,
Joachim Eastwood, Felipe Balbi, Lokesh Vutla, Rajendra Nayak,
Carlos Garcia, open list:OPEN FIRMWARE AND..., open list,
moderated list:ARM PORT, open list:OMAP DEVICE TREE...
This adds the NovaTech OrionLXm which is based on the AM335x SoC
http://www.novatechweb.com/substation-automation/orionlxm/
RAM: 512MiB
Flash: 4GB eMMC
Ethernet PHYs: 2x Micrel KSZ8041FTLI
USB ports are used internally by the expansion cards.
Internal micro SD slot is available.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
---
.../devicetree/bindings/arm/omap/omap.txt | 3 +
arch/arm/boot/dts/Makefile | 3 +-
arch/arm/boot/dts/am335x-lxm.dts | 362 +++++++++++++++++++++
3 files changed, 367 insertions(+), 1 deletion(-)
create mode 100644 arch/arm/boot/dts/am335x-lxm.dts
diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt
index ddd9bcd..4f6a82c 100644
--- a/Documentation/devicetree/bindings/arm/omap/omap.txt
+++ b/Documentation/devicetree/bindings/arm/omap/omap.txt
@@ -132,6 +132,9 @@ Boards:
- AM335X Bone : Low cost community board
compatible = "ti,am335x-bone", "ti,am33xx", "ti,omap3"
+- AM335X OrionLXm : Substation Automation Platform
+ compatible = "novatech,am335x-lxm", "ti,am33xx"
+
- OMAP5 EVM : Evaluation Module
compatible = "ti,omap5-evm", "ti,omap5"
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 38c89ca..454ee6c 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -331,7 +331,8 @@ dtb-$(CONFIG_SOC_AM33XX) += am335x-base0033.dtb \
am335x-evm.dtb \
am335x-evmsk.dtb \
am335x-nano.dtb \
- am335x-pepper.dtb
+ am335x-pepper.dtb \
+ am335x-lxm.dtb
dtb-$(CONFIG_ARCH_OMAP4) += omap4-duovero-parlor.dtb \
omap4-panda.dtb \
omap4-panda-a4.dtb \
diff --git a/arch/arm/boot/dts/am335x-lxm.dts b/arch/arm/boot/dts/am335x-lxm.dts
new file mode 100644
index 0000000..7266a00
--- /dev/null
+++ b/arch/arm/boot/dts/am335x-lxm.dts
@@ -0,0 +1,362 @@
+/*
+ * Copyright (C) 2014 NovaTech LLC - http://www.novatechweb.com
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+
+#include "am33xx.dtsi"
+
+/ {
+ model = "NovaTech OrionLXm";
+ compatible = "novatech,am335x-lxm", "ti,am33xx";
+
+ cpus {
+ cpu@0 {
+ cpu0-supply = <&vdd1_reg>;
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x80000000 0x20000000>; /* 512 MB */
+ };
+
+ /* Power supply provides a fixed 5V @2A */
+ vbat: fixedregulator@0 {
+ compatible = "regulator-fixed";
+ regulator-name = "vbat";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-boot-on;
+ };
+
+ /* Power supply provides a fixed 3.3V @3A */
+ vmmcsd_fixed: fixedregulator@1 {
+ compatible = "regulator-fixed";
+ regulator-name = "vmmcsd_fixed";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ };
+};
+
+&am33xx_pinmux {
+ mmc1_pins: pinmux_mmc1_pins {
+ pinctrl-single,pins = <
+ 0xf0 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat3 */
+ 0xf4 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat2 */
+ 0xf8 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat1 */
+ 0xfc (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat0 */
+ 0x100 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_clk */
+ 0x104 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_cmd */
+ >;
+ };
+
+ i2c0_pins: pinmux_i2c0_pins {
+ pinctrl-single,pins = <
+ 0x188 (PIN_INPUT | MUX_MODE0) /* i2c0_sda.i2c0_sda */
+ 0x18c (PIN_INPUT | MUX_MODE0) /* i2c0_scl.i2c0_scl */
+ >;
+ };
+
+ cpsw_default: cpsw_default {
+ pinctrl-single,pins = <
+ /* Slave 1 */
+ 0x64 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_int */
+ 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE1) /* rmii1_crs_dv */
+ 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* rmii1_rxer */
+ 0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* rmii1_txen */
+ 0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* rmii1_td1 */
+ 0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* rmii1_td0 */
+ 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE1) /* rmii1_rd1 */
+ 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* rmii1_rd0 */
+ 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* rmii1_refclk */
+
+ /* Slave 2 */
+ 0x40 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* rmii2_txen */
+ 0x50 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* rmii2_td1 */
+ 0x54 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* rmii2_td0 */
+ 0x68 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* rmii2_rd1 */
+ 0x6c (PIN_INPUT_PULLDOWN | MUX_MODE3) /* rmii2_rd0 */
+ 0x70 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* rmii2_crs_dv */
+ 0x74 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* rmii2_rxer */
+ 0x78 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_int */
+ 0x108 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* rmii2_refclk */
+ >;
+ };
+
+ cpsw_sleep: cpsw_sleep {
+ pinctrl-single,pins = <
+ /* Slave 1 reset value */
+ 0x64 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_int */
+ 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_crs_dv */
+ 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_rxer */
+ 0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_txen */
+ 0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_td1 */
+ 0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_td0 */
+ 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_rd1 */
+ 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_rd0 */
+ 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_refclk */
+
+ /* Slave 2 reset value*/
+ 0x40 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_txen */
+ 0x50 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_td1 */
+ 0x54 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_td0 */
+ 0x68 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_rd1 */
+ 0x6c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_rd0 */
+ 0x70 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_crs_dv */
+ 0x74 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_rxer */
+ 0x78 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_int */
+ 0x108 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_refclk */
+ >;
+ };
+
+ davinci_mdio_default: davinci_mdio_default {
+ pinctrl-single,pins = <
+ /* MDIO */
+ 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */
+ 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */
+ >;
+ };
+
+ davinci_mdio_sleep: davinci_mdio_sleep {
+ pinctrl-single,pins = <
+ /* MDIO reset value */
+ 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ >;
+ };
+
+ emmc_pins: pinmux_emmc_pins {
+ pinctrl-single,pins = <
+ 0x80 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn1.mmc1_clk */
+ 0x84 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn2.mmc1_cmd */
+ 0x00 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad0.mmc1_dat0 */
+ 0x04 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad1.mmc1_dat1 */
+ 0x08 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad2.mmc1_dat2 */
+ 0x0c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad3.mmc1_dat3 */
+ 0x10 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad4.mmc1_dat4 */
+ 0x14 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad5.mmc1_dat5 */
+ 0x18 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad6.mmc1_dat6 */
+ 0x1c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad7.mmc1_dat7 */
+ >;
+ };
+
+ uart0_pins: pinmux_uart0_pins {
+ pinctrl-single,pins = <
+ 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */
+ 0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */
+ >;
+ };
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins>;
+
+ status = "okay";
+ clock-frequency = <400000>;
+
+ serial_config1: serial_config1@20 {
+ compatible = "nxp,pca9539";
+ reg = <0x20>;
+ };
+
+ serial_config2: serial_config2@21 {
+ compatible = "nxp,pca9539";
+ reg = <0x21>;
+ };
+
+ tps: tps@2d {
+ compatible = "ti,tps65910";
+ reg = <0x2d>;
+ };
+};
+
+/include/ "tps65910.dtsi"
+
+&tps {
+ vcc1-supply = <&vbat>;
+ vcc2-supply = <&vbat>;
+ vcc3-supply = <&vbat>;
+ vcc4-supply = <&vbat>;
+ vcc5-supply = <&vbat>;
+ vcc6-supply = <&vbat>;
+ vcc7-supply = <&vbat>;
+ vccio-supply = <&vbat>;
+
+ regulators {
+ /* vrtc - unused */
+
+ vio_reg: regulator@1 {
+ regulator-name = "vio_1v5,ddr";
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vdd1_reg: regulator@2 {
+ regulator-name = "vdd1,mpu";
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vdd2_reg: regulator@3 {
+ regulator-name = "vdd2_1v1,core";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ /* vdd3 - unused */
+
+ /* vdig1 - unused */
+
+ vdig2_reg: regulator@6 {
+ regulator-name = "vdig2_1v8,vdds_pll";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ /* vpll - unused */
+
+ vdac_reg: regulator@8 {
+ regulator-name = "vdac_1v8,vdds";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vaux1_reg: regulator@9 {
+ regulator-name = "vaux1_1v8,usb";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vaux2_reg: regulator@10 {
+ regulator-name = "vaux2_3v3,io";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vaux33_reg: regulator@11 {
+ regulator-name = "vaux33_3v3,usb";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vmmc_reg: regulator@12 {
+ regulator-name = "vmmc_3v3,io";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ };
+};
+
+&sham {
+ status = "okay";
+};
+
+&aes {
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins>;
+
+ status = "okay";
+};
+
+&usb {
+ status = "okay";
+};
+
+&usb_ctrl_mod {
+ status = "okay";
+};
+
+&usb0_phy {
+ status = "okay";
+};
+
+&usb1_phy {
+ status = "okay";
+};
+
+&usb0 {
+ status = "okay";
+ dr_mode = "host";
+};
+
+&usb1 {
+ status = "okay";
+ dr_mode = "host";
+};
+
+&cppi41dma {
+ status = "okay";
+};
+
+&cpsw_emac0 {
+ phy_id = <&davinci_mdio>, <5>;
+ phy-mode = "rmii";
+ dual_emac_res_vlan = <2>;
+};
+
+&cpsw_emac1 {
+ phy_id = <&davinci_mdio>, <4>;
+ phy-mode = "rmii";
+ dual_emac_res_vlan = <3>;
+};
+
+&mac {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&cpsw_default>;
+ pinctrl-1 = <&cpsw_sleep>;
+ dual_emac = <1>;
+ status = "okay";
+};
+
+&davinci_mdio {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&davinci_mdio_default>;
+ pinctrl-1 = <&davinci_mdio_sleep>;
+ status = "okay";
+};
+
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins>;
+ vmmc-supply = <&vmmcsd_fixed>;
+ bus-width = <4>;
+ status = "okay";
+};
+
+&mmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&emmc_pins>;
+ vmmc-supply = <&vmmcsd_fixed>;
+ bus-width = <8>;
+ ti,non-removable;
+ status = "okay";
+};
+
--
2.1.0
^ permalink raw reply related [flat|nested] 11+ messages in thread* [PATCH v2 2/2] ARM: dts: Add devicetree for NovaTech OrionLXm
@ 2014-11-17 19:02 ` George McCollister
0 siblings, 0 replies; 11+ messages in thread
From: George McCollister @ 2014-11-17 19:02 UTC (permalink / raw)
To: linux-arm-kernel
This adds the NovaTech OrionLXm which is based on the AM335x SoC
http://www.novatechweb.com/substation-automation/orionlxm/
RAM: 512MiB
Flash: 4GB eMMC
Ethernet PHYs: 2x Micrel KSZ8041FTLI
USB ports are used internally by the expansion cards.
Internal micro SD slot is available.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
---
.../devicetree/bindings/arm/omap/omap.txt | 3 +
arch/arm/boot/dts/Makefile | 3 +-
arch/arm/boot/dts/am335x-lxm.dts | 362 +++++++++++++++++++++
3 files changed, 367 insertions(+), 1 deletion(-)
create mode 100644 arch/arm/boot/dts/am335x-lxm.dts
diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt
index ddd9bcd..4f6a82c 100644
--- a/Documentation/devicetree/bindings/arm/omap/omap.txt
+++ b/Documentation/devicetree/bindings/arm/omap/omap.txt
@@ -132,6 +132,9 @@ Boards:
- AM335X Bone : Low cost community board
compatible = "ti,am335x-bone", "ti,am33xx", "ti,omap3"
+- AM335X OrionLXm : Substation Automation Platform
+ compatible = "novatech,am335x-lxm", "ti,am33xx"
+
- OMAP5 EVM : Evaluation Module
compatible = "ti,omap5-evm", "ti,omap5"
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 38c89ca..454ee6c 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -331,7 +331,8 @@ dtb-$(CONFIG_SOC_AM33XX) += am335x-base0033.dtb \
am335x-evm.dtb \
am335x-evmsk.dtb \
am335x-nano.dtb \
- am335x-pepper.dtb
+ am335x-pepper.dtb \
+ am335x-lxm.dtb
dtb-$(CONFIG_ARCH_OMAP4) += omap4-duovero-parlor.dtb \
omap4-panda.dtb \
omap4-panda-a4.dtb \
diff --git a/arch/arm/boot/dts/am335x-lxm.dts b/arch/arm/boot/dts/am335x-lxm.dts
new file mode 100644
index 0000000..7266a00
--- /dev/null
+++ b/arch/arm/boot/dts/am335x-lxm.dts
@@ -0,0 +1,362 @@
+/*
+ * Copyright (C) 2014 NovaTech LLC - http://www.novatechweb.com
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+
+#include "am33xx.dtsi"
+
+/ {
+ model = "NovaTech OrionLXm";
+ compatible = "novatech,am335x-lxm", "ti,am33xx";
+
+ cpus {
+ cpu at 0 {
+ cpu0-supply = <&vdd1_reg>;
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x80000000 0x20000000>; /* 512 MB */
+ };
+
+ /* Power supply provides a fixed 5V @2A */
+ vbat: fixedregulator at 0 {
+ compatible = "regulator-fixed";
+ regulator-name = "vbat";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-boot-on;
+ };
+
+ /* Power supply provides a fixed 3.3V @3A */
+ vmmcsd_fixed: fixedregulator at 1 {
+ compatible = "regulator-fixed";
+ regulator-name = "vmmcsd_fixed";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ };
+};
+
+&am33xx_pinmux {
+ mmc1_pins: pinmux_mmc1_pins {
+ pinctrl-single,pins = <
+ 0xf0 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat3 */
+ 0xf4 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat2 */
+ 0xf8 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat1 */
+ 0xfc (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat0 */
+ 0x100 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_clk */
+ 0x104 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_cmd */
+ >;
+ };
+
+ i2c0_pins: pinmux_i2c0_pins {
+ pinctrl-single,pins = <
+ 0x188 (PIN_INPUT | MUX_MODE0) /* i2c0_sda.i2c0_sda */
+ 0x18c (PIN_INPUT | MUX_MODE0) /* i2c0_scl.i2c0_scl */
+ >;
+ };
+
+ cpsw_default: cpsw_default {
+ pinctrl-single,pins = <
+ /* Slave 1 */
+ 0x64 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_int */
+ 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE1) /* rmii1_crs_dv */
+ 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* rmii1_rxer */
+ 0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* rmii1_txen */
+ 0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* rmii1_td1 */
+ 0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* rmii1_td0 */
+ 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE1) /* rmii1_rd1 */
+ 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* rmii1_rd0 */
+ 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* rmii1_refclk */
+
+ /* Slave 2 */
+ 0x40 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* rmii2_txen */
+ 0x50 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* rmii2_td1 */
+ 0x54 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* rmii2_td0 */
+ 0x68 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* rmii2_rd1 */
+ 0x6c (PIN_INPUT_PULLDOWN | MUX_MODE3) /* rmii2_rd0 */
+ 0x70 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* rmii2_crs_dv */
+ 0x74 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* rmii2_rxer */
+ 0x78 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_int */
+ 0x108 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* rmii2_refclk */
+ >;
+ };
+
+ cpsw_sleep: cpsw_sleep {
+ pinctrl-single,pins = <
+ /* Slave 1 reset value */
+ 0x64 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_int */
+ 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_crs_dv */
+ 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_rxer */
+ 0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_txen */
+ 0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_td1 */
+ 0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_td0 */
+ 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_rd1 */
+ 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_rd0 */
+ 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_refclk */
+
+ /* Slave 2 reset value*/
+ 0x40 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_txen */
+ 0x50 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_td1 */
+ 0x54 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_td0 */
+ 0x68 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_rd1 */
+ 0x6c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_rd0 */
+ 0x70 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_crs_dv */
+ 0x74 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_rxer */
+ 0x78 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_int */
+ 0x108 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_refclk */
+ >;
+ };
+
+ davinci_mdio_default: davinci_mdio_default {
+ pinctrl-single,pins = <
+ /* MDIO */
+ 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */
+ 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */
+ >;
+ };
+
+ davinci_mdio_sleep: davinci_mdio_sleep {
+ pinctrl-single,pins = <
+ /* MDIO reset value */
+ 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ >;
+ };
+
+ emmc_pins: pinmux_emmc_pins {
+ pinctrl-single,pins = <
+ 0x80 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn1.mmc1_clk */
+ 0x84 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn2.mmc1_cmd */
+ 0x00 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad0.mmc1_dat0 */
+ 0x04 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad1.mmc1_dat1 */
+ 0x08 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad2.mmc1_dat2 */
+ 0x0c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad3.mmc1_dat3 */
+ 0x10 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad4.mmc1_dat4 */
+ 0x14 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad5.mmc1_dat5 */
+ 0x18 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad6.mmc1_dat6 */
+ 0x1c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad7.mmc1_dat7 */
+ >;
+ };
+
+ uart0_pins: pinmux_uart0_pins {
+ pinctrl-single,pins = <
+ 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */
+ 0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */
+ >;
+ };
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins>;
+
+ status = "okay";
+ clock-frequency = <400000>;
+
+ serial_config1: serial_config1 at 20 {
+ compatible = "nxp,pca9539";
+ reg = <0x20>;
+ };
+
+ serial_config2: serial_config2 at 21 {
+ compatible = "nxp,pca9539";
+ reg = <0x21>;
+ };
+
+ tps: tps at 2d {
+ compatible = "ti,tps65910";
+ reg = <0x2d>;
+ };
+};
+
+/include/ "tps65910.dtsi"
+
+&tps {
+ vcc1-supply = <&vbat>;
+ vcc2-supply = <&vbat>;
+ vcc3-supply = <&vbat>;
+ vcc4-supply = <&vbat>;
+ vcc5-supply = <&vbat>;
+ vcc6-supply = <&vbat>;
+ vcc7-supply = <&vbat>;
+ vccio-supply = <&vbat>;
+
+ regulators {
+ /* vrtc - unused */
+
+ vio_reg: regulator at 1 {
+ regulator-name = "vio_1v5,ddr";
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vdd1_reg: regulator at 2 {
+ regulator-name = "vdd1,mpu";
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vdd2_reg: regulator at 3 {
+ regulator-name = "vdd2_1v1,core";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ /* vdd3 - unused */
+
+ /* vdig1 - unused */
+
+ vdig2_reg: regulator at 6 {
+ regulator-name = "vdig2_1v8,vdds_pll";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ /* vpll - unused */
+
+ vdac_reg: regulator at 8 {
+ regulator-name = "vdac_1v8,vdds";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vaux1_reg: regulator at 9 {
+ regulator-name = "vaux1_1v8,usb";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vaux2_reg: regulator at 10 {
+ regulator-name = "vaux2_3v3,io";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vaux33_reg: regulator at 11 {
+ regulator-name = "vaux33_3v3,usb";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vmmc_reg: regulator at 12 {
+ regulator-name = "vmmc_3v3,io";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ };
+};
+
+&sham {
+ status = "okay";
+};
+
+&aes {
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins>;
+
+ status = "okay";
+};
+
+&usb {
+ status = "okay";
+};
+
+&usb_ctrl_mod {
+ status = "okay";
+};
+
+&usb0_phy {
+ status = "okay";
+};
+
+&usb1_phy {
+ status = "okay";
+};
+
+&usb0 {
+ status = "okay";
+ dr_mode = "host";
+};
+
+&usb1 {
+ status = "okay";
+ dr_mode = "host";
+};
+
+&cppi41dma {
+ status = "okay";
+};
+
+&cpsw_emac0 {
+ phy_id = <&davinci_mdio>, <5>;
+ phy-mode = "rmii";
+ dual_emac_res_vlan = <2>;
+};
+
+&cpsw_emac1 {
+ phy_id = <&davinci_mdio>, <4>;
+ phy-mode = "rmii";
+ dual_emac_res_vlan = <3>;
+};
+
+&mac {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&cpsw_default>;
+ pinctrl-1 = <&cpsw_sleep>;
+ dual_emac = <1>;
+ status = "okay";
+};
+
+&davinci_mdio {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&davinci_mdio_default>;
+ pinctrl-1 = <&davinci_mdio_sleep>;
+ status = "okay";
+};
+
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins>;
+ vmmc-supply = <&vmmcsd_fixed>;
+ bus-width = <4>;
+ status = "okay";
+};
+
+&mmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&emmc_pins>;
+ vmmc-supply = <&vmmcsd_fixed>;
+ bus-width = <8>;
+ ti,non-removable;
+ status = "okay";
+};
+
--
2.1.0
^ permalink raw reply related [flat|nested] 11+ messages in thread* Re: [PATCH v2 2/2] ARM: dts: Add devicetree for NovaTech OrionLXm
2014-11-17 19:02 ` George McCollister
@ 2014-11-17 19:09 ` Felipe Balbi
-1 siblings, 0 replies; 11+ messages in thread
From: Felipe Balbi @ 2014-11-17 19:09 UTC (permalink / raw)
To: George McCollister
Cc: Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala,
Russell King, Benoît Cousson, Tony Lindgren, Nishanth Menon,
Florian Vaussard, Tomi Valkeinen, Joachim Eastwood, Felipe Balbi,
Lokesh Vutla, Carlos Garcia, open list:OPEN FIRMWARE AND...,
open list, moderated list:ARM PORT, open list:OMAP DEVICE TREE...
[-- Attachment #1: Type: text/plain, Size: 12607 bytes --]
On Mon, Nov 17, 2014 at 01:02:35PM -0600, George McCollister wrote:
> This adds the NovaTech OrionLXm which is based on the AM335x SoC
> http://www.novatechweb.com/substation-automation/orionlxm/
>
> RAM: 512MiB
> Flash: 4GB eMMC
> Ethernet PHYs: 2x Micrel KSZ8041FTLI
> USB ports are used internally by the expansion cards.
> Internal micro SD slot is available.
>
> Signed-off-by: George McCollister <george.mccollister@gmail.com>
this looks might better to my eyes:
Reviewed-by: Felipe Balbi <balbi@ti.com>
> ---
> .../devicetree/bindings/arm/omap/omap.txt | 3 +
> arch/arm/boot/dts/Makefile | 3 +-
> arch/arm/boot/dts/am335x-lxm.dts | 362 +++++++++++++++++++++
> 3 files changed, 367 insertions(+), 1 deletion(-)
> create mode 100644 arch/arm/boot/dts/am335x-lxm.dts
>
> diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt
> index ddd9bcd..4f6a82c 100644
> --- a/Documentation/devicetree/bindings/arm/omap/omap.txt
> +++ b/Documentation/devicetree/bindings/arm/omap/omap.txt
> @@ -132,6 +132,9 @@ Boards:
> - AM335X Bone : Low cost community board
> compatible = "ti,am335x-bone", "ti,am33xx", "ti,omap3"
>
> +- AM335X OrionLXm : Substation Automation Platform
> + compatible = "novatech,am335x-lxm", "ti,am33xx"
> +
> - OMAP5 EVM : Evaluation Module
> compatible = "ti,omap5-evm", "ti,omap5"
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 38c89ca..454ee6c 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -331,7 +331,8 @@ dtb-$(CONFIG_SOC_AM33XX) += am335x-base0033.dtb \
> am335x-evm.dtb \
> am335x-evmsk.dtb \
> am335x-nano.dtb \
> - am335x-pepper.dtb
> + am335x-pepper.dtb \
> + am335x-lxm.dtb
> dtb-$(CONFIG_ARCH_OMAP4) += omap4-duovero-parlor.dtb \
> omap4-panda.dtb \
> omap4-panda-a4.dtb \
> diff --git a/arch/arm/boot/dts/am335x-lxm.dts b/arch/arm/boot/dts/am335x-lxm.dts
> new file mode 100644
> index 0000000..7266a00
> --- /dev/null
> +++ b/arch/arm/boot/dts/am335x-lxm.dts
> @@ -0,0 +1,362 @@
> +/*
> + * Copyright (C) 2014 NovaTech LLC - http://www.novatechweb.com
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + */
> +/dts-v1/;
> +
> +#include "am33xx.dtsi"
> +
> +/ {
> + model = "NovaTech OrionLXm";
> + compatible = "novatech,am335x-lxm", "ti,am33xx";
> +
> + cpus {
> + cpu@0 {
> + cpu0-supply = <&vdd1_reg>;
> + };
> + };
> +
> + memory {
> + device_type = "memory";
> + reg = <0x80000000 0x20000000>; /* 512 MB */
> + };
> +
> + /* Power supply provides a fixed 5V @2A */
> + vbat: fixedregulator@0 {
> + compatible = "regulator-fixed";
> + regulator-name = "vbat";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-boot-on;
> + };
> +
> + /* Power supply provides a fixed 3.3V @3A */
> + vmmcsd_fixed: fixedregulator@1 {
> + compatible = "regulator-fixed";
> + regulator-name = "vmmcsd_fixed";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + };
> +};
> +
> +&am33xx_pinmux {
> + mmc1_pins: pinmux_mmc1_pins {
> + pinctrl-single,pins = <
> + 0xf0 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat3 */
> + 0xf4 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat2 */
> + 0xf8 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat1 */
> + 0xfc (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat0 */
> + 0x100 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_clk */
> + 0x104 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_cmd */
> + >;
> + };
> +
> + i2c0_pins: pinmux_i2c0_pins {
> + pinctrl-single,pins = <
> + 0x188 (PIN_INPUT | MUX_MODE0) /* i2c0_sda.i2c0_sda */
> + 0x18c (PIN_INPUT | MUX_MODE0) /* i2c0_scl.i2c0_scl */
> + >;
> + };
> +
> + cpsw_default: cpsw_default {
> + pinctrl-single,pins = <
> + /* Slave 1 */
> + 0x64 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_int */
> + 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE1) /* rmii1_crs_dv */
> + 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* rmii1_rxer */
> + 0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* rmii1_txen */
> + 0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* rmii1_td1 */
> + 0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* rmii1_td0 */
> + 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE1) /* rmii1_rd1 */
> + 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* rmii1_rd0 */
> + 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* rmii1_refclk */
> +
> + /* Slave 2 */
> + 0x40 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* rmii2_txen */
> + 0x50 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* rmii2_td1 */
> + 0x54 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* rmii2_td0 */
> + 0x68 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* rmii2_rd1 */
> + 0x6c (PIN_INPUT_PULLDOWN | MUX_MODE3) /* rmii2_rd0 */
> + 0x70 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* rmii2_crs_dv */
> + 0x74 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* rmii2_rxer */
> + 0x78 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_int */
> + 0x108 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* rmii2_refclk */
> + >;
> + };
> +
> + cpsw_sleep: cpsw_sleep {
> + pinctrl-single,pins = <
> + /* Slave 1 reset value */
> + 0x64 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_int */
> + 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_crs_dv */
> + 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_rxer */
> + 0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_txen */
> + 0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_td1 */
> + 0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_td0 */
> + 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_rd1 */
> + 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_rd0 */
> + 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_refclk */
> +
> + /* Slave 2 reset value*/
> + 0x40 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_txen */
> + 0x50 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_td1 */
> + 0x54 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_td0 */
> + 0x68 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_rd1 */
> + 0x6c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_rd0 */
> + 0x70 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_crs_dv */
> + 0x74 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_rxer */
> + 0x78 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_int */
> + 0x108 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_refclk */
> + >;
> + };
> +
> + davinci_mdio_default: davinci_mdio_default {
> + pinctrl-single,pins = <
> + /* MDIO */
> + 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */
> + 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */
> + >;
> + };
> +
> + davinci_mdio_sleep: davinci_mdio_sleep {
> + pinctrl-single,pins = <
> + /* MDIO reset value */
> + 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7)
> + 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7)
> + >;
> + };
> +
> + emmc_pins: pinmux_emmc_pins {
> + pinctrl-single,pins = <
> + 0x80 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn1.mmc1_clk */
> + 0x84 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn2.mmc1_cmd */
> + 0x00 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad0.mmc1_dat0 */
> + 0x04 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad1.mmc1_dat1 */
> + 0x08 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad2.mmc1_dat2 */
> + 0x0c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad3.mmc1_dat3 */
> + 0x10 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad4.mmc1_dat4 */
> + 0x14 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad5.mmc1_dat5 */
> + 0x18 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad6.mmc1_dat6 */
> + 0x1c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad7.mmc1_dat7 */
> + >;
> + };
> +
> + uart0_pins: pinmux_uart0_pins {
> + pinctrl-single,pins = <
> + 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */
> + 0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */
> + >;
> + };
> +};
> +
> +&i2c0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c0_pins>;
> +
> + status = "okay";
> + clock-frequency = <400000>;
> +
> + serial_config1: serial_config1@20 {
> + compatible = "nxp,pca9539";
> + reg = <0x20>;
> + };
> +
> + serial_config2: serial_config2@21 {
> + compatible = "nxp,pca9539";
> + reg = <0x21>;
> + };
> +
> + tps: tps@2d {
> + compatible = "ti,tps65910";
> + reg = <0x2d>;
> + };
> +};
> +
> +/include/ "tps65910.dtsi"
> +
> +&tps {
> + vcc1-supply = <&vbat>;
> + vcc2-supply = <&vbat>;
> + vcc3-supply = <&vbat>;
> + vcc4-supply = <&vbat>;
> + vcc5-supply = <&vbat>;
> + vcc6-supply = <&vbat>;
> + vcc7-supply = <&vbat>;
> + vccio-supply = <&vbat>;
> +
> + regulators {
> + /* vrtc - unused */
> +
> + vio_reg: regulator@1 {
> + regulator-name = "vio_1v5,ddr";
> + regulator-min-microvolt = <1500000>;
> + regulator-max-microvolt = <1500000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + vdd1_reg: regulator@2 {
> + regulator-name = "vdd1,mpu";
> + regulator-min-microvolt = <600000>;
> + regulator-max-microvolt = <1500000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + vdd2_reg: regulator@3 {
> + regulator-name = "vdd2_1v1,core";
> + regulator-min-microvolt = <1100000>;
> + regulator-max-microvolt = <1100000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + /* vdd3 - unused */
> +
> + /* vdig1 - unused */
> +
> + vdig2_reg: regulator@6 {
> + regulator-name = "vdig2_1v8,vdds_pll";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + /* vpll - unused */
> +
> + vdac_reg: regulator@8 {
> + regulator-name = "vdac_1v8,vdds";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + vaux1_reg: regulator@9 {
> + regulator-name = "vaux1_1v8,usb";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + vaux2_reg: regulator@10 {
> + regulator-name = "vaux2_3v3,io";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + vaux33_reg: regulator@11 {
> + regulator-name = "vaux33_3v3,usb";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + vmmc_reg: regulator@12 {
> + regulator-name = "vmmc_3v3,io";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> + };
> +};
> +
> +&sham {
> + status = "okay";
> +};
> +
> +&aes {
> + status = "okay";
> +};
> +
> +&uart0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart0_pins>;
> +
> + status = "okay";
> +};
> +
> +&usb {
> + status = "okay";
> +};
> +
> +&usb_ctrl_mod {
> + status = "okay";
> +};
> +
> +&usb0_phy {
> + status = "okay";
> +};
> +
> +&usb1_phy {
> + status = "okay";
> +};
> +
> +&usb0 {
> + status = "okay";
> + dr_mode = "host";
> +};
> +
> +&usb1 {
> + status = "okay";
> + dr_mode = "host";
> +};
> +
> +&cppi41dma {
> + status = "okay";
> +};
> +
> +&cpsw_emac0 {
> + phy_id = <&davinci_mdio>, <5>;
> + phy-mode = "rmii";
> + dual_emac_res_vlan = <2>;
> +};
> +
> +&cpsw_emac1 {
> + phy_id = <&davinci_mdio>, <4>;
> + phy-mode = "rmii";
> + dual_emac_res_vlan = <3>;
> +};
> +
> +&mac {
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&cpsw_default>;
> + pinctrl-1 = <&cpsw_sleep>;
> + dual_emac = <1>;
> + status = "okay";
> +};
> +
> +&davinci_mdio {
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&davinci_mdio_default>;
> + pinctrl-1 = <&davinci_mdio_sleep>;
> + status = "okay";
> +};
> +
> +&mmc1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&mmc1_pins>;
> + vmmc-supply = <&vmmcsd_fixed>;
> + bus-width = <4>;
> + status = "okay";
> +};
> +
> +&mmc2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&emmc_pins>;
> + vmmc-supply = <&vmmcsd_fixed>;
> + bus-width = <8>;
> + ti,non-removable;
> + status = "okay";
> +};
> +
> --
> 2.1.0
>
--
balbi
[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 819 bytes --]
^ permalink raw reply [flat|nested] 11+ messages in thread* [PATCH v2 2/2] ARM: dts: Add devicetree for NovaTech OrionLXm
@ 2014-11-17 19:09 ` Felipe Balbi
0 siblings, 0 replies; 11+ messages in thread
From: Felipe Balbi @ 2014-11-17 19:09 UTC (permalink / raw)
To: linux-arm-kernel
On Mon, Nov 17, 2014 at 01:02:35PM -0600, George McCollister wrote:
> This adds the NovaTech OrionLXm which is based on the AM335x SoC
> http://www.novatechweb.com/substation-automation/orionlxm/
>
> RAM: 512MiB
> Flash: 4GB eMMC
> Ethernet PHYs: 2x Micrel KSZ8041FTLI
> USB ports are used internally by the expansion cards.
> Internal micro SD slot is available.
>
> Signed-off-by: George McCollister <george.mccollister@gmail.com>
this looks might better to my eyes:
Reviewed-by: Felipe Balbi <balbi@ti.com>
> ---
> .../devicetree/bindings/arm/omap/omap.txt | 3 +
> arch/arm/boot/dts/Makefile | 3 +-
> arch/arm/boot/dts/am335x-lxm.dts | 362 +++++++++++++++++++++
> 3 files changed, 367 insertions(+), 1 deletion(-)
> create mode 100644 arch/arm/boot/dts/am335x-lxm.dts
>
> diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt
> index ddd9bcd..4f6a82c 100644
> --- a/Documentation/devicetree/bindings/arm/omap/omap.txt
> +++ b/Documentation/devicetree/bindings/arm/omap/omap.txt
> @@ -132,6 +132,9 @@ Boards:
> - AM335X Bone : Low cost community board
> compatible = "ti,am335x-bone", "ti,am33xx", "ti,omap3"
>
> +- AM335X OrionLXm : Substation Automation Platform
> + compatible = "novatech,am335x-lxm", "ti,am33xx"
> +
> - OMAP5 EVM : Evaluation Module
> compatible = "ti,omap5-evm", "ti,omap5"
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 38c89ca..454ee6c 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -331,7 +331,8 @@ dtb-$(CONFIG_SOC_AM33XX) += am335x-base0033.dtb \
> am335x-evm.dtb \
> am335x-evmsk.dtb \
> am335x-nano.dtb \
> - am335x-pepper.dtb
> + am335x-pepper.dtb \
> + am335x-lxm.dtb
> dtb-$(CONFIG_ARCH_OMAP4) += omap4-duovero-parlor.dtb \
> omap4-panda.dtb \
> omap4-panda-a4.dtb \
> diff --git a/arch/arm/boot/dts/am335x-lxm.dts b/arch/arm/boot/dts/am335x-lxm.dts
> new file mode 100644
> index 0000000..7266a00
> --- /dev/null
> +++ b/arch/arm/boot/dts/am335x-lxm.dts
> @@ -0,0 +1,362 @@
> +/*
> + * Copyright (C) 2014 NovaTech LLC - http://www.novatechweb.com
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + */
> +/dts-v1/;
> +
> +#include "am33xx.dtsi"
> +
> +/ {
> + model = "NovaTech OrionLXm";
> + compatible = "novatech,am335x-lxm", "ti,am33xx";
> +
> + cpus {
> + cpu at 0 {
> + cpu0-supply = <&vdd1_reg>;
> + };
> + };
> +
> + memory {
> + device_type = "memory";
> + reg = <0x80000000 0x20000000>; /* 512 MB */
> + };
> +
> + /* Power supply provides a fixed 5V @2A */
> + vbat: fixedregulator at 0 {
> + compatible = "regulator-fixed";
> + regulator-name = "vbat";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-boot-on;
> + };
> +
> + /* Power supply provides a fixed 3.3V @3A */
> + vmmcsd_fixed: fixedregulator at 1 {
> + compatible = "regulator-fixed";
> + regulator-name = "vmmcsd_fixed";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + };
> +};
> +
> +&am33xx_pinmux {
> + mmc1_pins: pinmux_mmc1_pins {
> + pinctrl-single,pins = <
> + 0xf0 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat3 */
> + 0xf4 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat2 */
> + 0xf8 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat1 */
> + 0xfc (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat0 */
> + 0x100 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_clk */
> + 0x104 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_cmd */
> + >;
> + };
> +
> + i2c0_pins: pinmux_i2c0_pins {
> + pinctrl-single,pins = <
> + 0x188 (PIN_INPUT | MUX_MODE0) /* i2c0_sda.i2c0_sda */
> + 0x18c (PIN_INPUT | MUX_MODE0) /* i2c0_scl.i2c0_scl */
> + >;
> + };
> +
> + cpsw_default: cpsw_default {
> + pinctrl-single,pins = <
> + /* Slave 1 */
> + 0x64 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_int */
> + 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE1) /* rmii1_crs_dv */
> + 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* rmii1_rxer */
> + 0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* rmii1_txen */
> + 0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* rmii1_td1 */
> + 0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* rmii1_td0 */
> + 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE1) /* rmii1_rd1 */
> + 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* rmii1_rd0 */
> + 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* rmii1_refclk */
> +
> + /* Slave 2 */
> + 0x40 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* rmii2_txen */
> + 0x50 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* rmii2_td1 */
> + 0x54 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* rmii2_td0 */
> + 0x68 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* rmii2_rd1 */
> + 0x6c (PIN_INPUT_PULLDOWN | MUX_MODE3) /* rmii2_rd0 */
> + 0x70 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* rmii2_crs_dv */
> + 0x74 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* rmii2_rxer */
> + 0x78 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_int */
> + 0x108 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* rmii2_refclk */
> + >;
> + };
> +
> + cpsw_sleep: cpsw_sleep {
> + pinctrl-single,pins = <
> + /* Slave 1 reset value */
> + 0x64 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_int */
> + 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_crs_dv */
> + 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_rxer */
> + 0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_txen */
> + 0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_td1 */
> + 0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_td0 */
> + 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_rd1 */
> + 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_rd0 */
> + 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_refclk */
> +
> + /* Slave 2 reset value*/
> + 0x40 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_txen */
> + 0x50 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_td1 */
> + 0x54 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_td0 */
> + 0x68 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_rd1 */
> + 0x6c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_rd0 */
> + 0x70 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_crs_dv */
> + 0x74 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_rxer */
> + 0x78 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_int */
> + 0x108 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii2_refclk */
> + >;
> + };
> +
> + davinci_mdio_default: davinci_mdio_default {
> + pinctrl-single,pins = <
> + /* MDIO */
> + 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */
> + 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */
> + >;
> + };
> +
> + davinci_mdio_sleep: davinci_mdio_sleep {
> + pinctrl-single,pins = <
> + /* MDIO reset value */
> + 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7)
> + 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7)
> + >;
> + };
> +
> + emmc_pins: pinmux_emmc_pins {
> + pinctrl-single,pins = <
> + 0x80 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn1.mmc1_clk */
> + 0x84 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn2.mmc1_cmd */
> + 0x00 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad0.mmc1_dat0 */
> + 0x04 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad1.mmc1_dat1 */
> + 0x08 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad2.mmc1_dat2 */
> + 0x0c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad3.mmc1_dat3 */
> + 0x10 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad4.mmc1_dat4 */
> + 0x14 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad5.mmc1_dat5 */
> + 0x18 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad6.mmc1_dat6 */
> + 0x1c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad7.mmc1_dat7 */
> + >;
> + };
> +
> + uart0_pins: pinmux_uart0_pins {
> + pinctrl-single,pins = <
> + 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */
> + 0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */
> + >;
> + };
> +};
> +
> +&i2c0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c0_pins>;
> +
> + status = "okay";
> + clock-frequency = <400000>;
> +
> + serial_config1: serial_config1 at 20 {
> + compatible = "nxp,pca9539";
> + reg = <0x20>;
> + };
> +
> + serial_config2: serial_config2 at 21 {
> + compatible = "nxp,pca9539";
> + reg = <0x21>;
> + };
> +
> + tps: tps at 2d {
> + compatible = "ti,tps65910";
> + reg = <0x2d>;
> + };
> +};
> +
> +/include/ "tps65910.dtsi"
> +
> +&tps {
> + vcc1-supply = <&vbat>;
> + vcc2-supply = <&vbat>;
> + vcc3-supply = <&vbat>;
> + vcc4-supply = <&vbat>;
> + vcc5-supply = <&vbat>;
> + vcc6-supply = <&vbat>;
> + vcc7-supply = <&vbat>;
> + vccio-supply = <&vbat>;
> +
> + regulators {
> + /* vrtc - unused */
> +
> + vio_reg: regulator at 1 {
> + regulator-name = "vio_1v5,ddr";
> + regulator-min-microvolt = <1500000>;
> + regulator-max-microvolt = <1500000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + vdd1_reg: regulator at 2 {
> + regulator-name = "vdd1,mpu";
> + regulator-min-microvolt = <600000>;
> + regulator-max-microvolt = <1500000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + vdd2_reg: regulator at 3 {
> + regulator-name = "vdd2_1v1,core";
> + regulator-min-microvolt = <1100000>;
> + regulator-max-microvolt = <1100000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + /* vdd3 - unused */
> +
> + /* vdig1 - unused */
> +
> + vdig2_reg: regulator at 6 {
> + regulator-name = "vdig2_1v8,vdds_pll";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + /* vpll - unused */
> +
> + vdac_reg: regulator at 8 {
> + regulator-name = "vdac_1v8,vdds";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + vaux1_reg: regulator at 9 {
> + regulator-name = "vaux1_1v8,usb";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + vaux2_reg: regulator at 10 {
> + regulator-name = "vaux2_3v3,io";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + vaux33_reg: regulator at 11 {
> + regulator-name = "vaux33_3v3,usb";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + vmmc_reg: regulator at 12 {
> + regulator-name = "vmmc_3v3,io";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> + };
> +};
> +
> +&sham {
> + status = "okay";
> +};
> +
> +&aes {
> + status = "okay";
> +};
> +
> +&uart0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart0_pins>;
> +
> + status = "okay";
> +};
> +
> +&usb {
> + status = "okay";
> +};
> +
> +&usb_ctrl_mod {
> + status = "okay";
> +};
> +
> +&usb0_phy {
> + status = "okay";
> +};
> +
> +&usb1_phy {
> + status = "okay";
> +};
> +
> +&usb0 {
> + status = "okay";
> + dr_mode = "host";
> +};
> +
> +&usb1 {
> + status = "okay";
> + dr_mode = "host";
> +};
> +
> +&cppi41dma {
> + status = "okay";
> +};
> +
> +&cpsw_emac0 {
> + phy_id = <&davinci_mdio>, <5>;
> + phy-mode = "rmii";
> + dual_emac_res_vlan = <2>;
> +};
> +
> +&cpsw_emac1 {
> + phy_id = <&davinci_mdio>, <4>;
> + phy-mode = "rmii";
> + dual_emac_res_vlan = <3>;
> +};
> +
> +&mac {
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&cpsw_default>;
> + pinctrl-1 = <&cpsw_sleep>;
> + dual_emac = <1>;
> + status = "okay";
> +};
> +
> +&davinci_mdio {
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&davinci_mdio_default>;
> + pinctrl-1 = <&davinci_mdio_sleep>;
> + status = "okay";
> +};
> +
> +&mmc1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&mmc1_pins>;
> + vmmc-supply = <&vmmcsd_fixed>;
> + bus-width = <4>;
> + status = "okay";
> +};
> +
> +&mmc2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&emmc_pins>;
> + vmmc-supply = <&vmmcsd_fixed>;
> + bus-width = <8>;
> + ti,non-removable;
> + status = "okay";
> +};
> +
> --
> 2.1.0
>
--
balbi
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20141117/4be311fc/attachment-0001.sig>
^ permalink raw reply [flat|nested] 11+ messages in thread* Re: [PATCH v2 2/2] ARM: dts: Add devicetree for NovaTech OrionLXm
2014-11-17 19:09 ` Felipe Balbi
(?)
@ 2014-11-21 23:33 ` Tony Lindgren
-1 siblings, 0 replies; 11+ messages in thread
From: Tony Lindgren @ 2014-11-21 23:33 UTC (permalink / raw)
To: Felipe Balbi
Cc: George McCollister, Rob Herring, Pawel Moll, Mark Rutland,
Ian Campbell, Kumar Gala, Russell King, Benoît Cousson,
Nishanth Menon, Florian Vaussard, Tomi Valkeinen,
Joachim Eastwood, Lokesh Vutla, Carlos Garcia,
open list:OPEN FIRMWARE AND..., open list,
moderated list:ARM PORT, open list:OMAP DEVICE TREE...
* Felipe Balbi <balbi-l0cyMroinI0@public.gmane.org> [141117 11:10]:
> On Mon, Nov 17, 2014 at 01:02:35PM -0600, George McCollister wrote:
> > This adds the NovaTech OrionLXm which is based on the AM335x SoC
> > http://www.novatechweb.com/substation-automation/orionlxm/
> >
> > RAM: 512MiB
> > Flash: 4GB eMMC
> > Ethernet PHYs: 2x Micrel KSZ8041FTLI
> > USB ports are used internally by the expansion cards.
> > Internal micro SD slot is available.
> >
> > Signed-off-by: George McCollister <george.mccollister-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
>
> this looks might better to my eyes:
>
> Reviewed-by: Felipe Balbi <balbi-l0cyMroinI0@public.gmane.org>
Applying into omap-for-v3.19/dt-v2 thanks.
Tony
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [PATCH v2 2/2] ARM: dts: Add devicetree for NovaTech OrionLXm
@ 2014-11-21 23:33 ` Tony Lindgren
0 siblings, 0 replies; 11+ messages in thread
From: Tony Lindgren @ 2014-11-21 23:33 UTC (permalink / raw)
To: Felipe Balbi
Cc: George McCollister, Rob Herring, Pawel Moll, Mark Rutland,
Ian Campbell, Kumar Gala, Russell King, Benoît Cousson,
Nishanth Menon, Florian Vaussard, Tomi Valkeinen,
Joachim Eastwood, Lokesh Vutla, Carlos Garcia,
open list:OPEN FIRMWARE AND..., open list,
moderated list:ARM PORT, open list:OMAP DEVICE TREE...
* Felipe Balbi <balbi@ti.com> [141117 11:10]:
> On Mon, Nov 17, 2014 at 01:02:35PM -0600, George McCollister wrote:
> > This adds the NovaTech OrionLXm which is based on the AM335x SoC
> > http://www.novatechweb.com/substation-automation/orionlxm/
> >
> > RAM: 512MiB
> > Flash: 4GB eMMC
> > Ethernet PHYs: 2x Micrel KSZ8041FTLI
> > USB ports are used internally by the expansion cards.
> > Internal micro SD slot is available.
> >
> > Signed-off-by: George McCollister <george.mccollister@gmail.com>
>
> this looks might better to my eyes:
>
> Reviewed-by: Felipe Balbi <balbi@ti.com>
Applying into omap-for-v3.19/dt-v2 thanks.
Tony
^ permalink raw reply [flat|nested] 11+ messages in thread
* [PATCH v2 2/2] ARM: dts: Add devicetree for NovaTech OrionLXm
@ 2014-11-21 23:33 ` Tony Lindgren
0 siblings, 0 replies; 11+ messages in thread
From: Tony Lindgren @ 2014-11-21 23:33 UTC (permalink / raw)
To: linux-arm-kernel
* Felipe Balbi <balbi@ti.com> [141117 11:10]:
> On Mon, Nov 17, 2014 at 01:02:35PM -0600, George McCollister wrote:
> > This adds the NovaTech OrionLXm which is based on the AM335x SoC
> > http://www.novatechweb.com/substation-automation/orionlxm/
> >
> > RAM: 512MiB
> > Flash: 4GB eMMC
> > Ethernet PHYs: 2x Micrel KSZ8041FTLI
> > USB ports are used internally by the expansion cards.
> > Internal micro SD slot is available.
> >
> > Signed-off-by: George McCollister <george.mccollister@gmail.com>
>
> this looks might better to my eyes:
>
> Reviewed-by: Felipe Balbi <balbi@ti.com>
Applying into omap-for-v3.19/dt-v2 thanks.
Tony
^ permalink raw reply [flat|nested] 11+ messages in thread